Superior mechanical and electrical properties of multiwall carbon nanotube reinforced acrylonitrile butadiene styrene high performance composites

In-house synthesized multiwall carbon nanotubes (MWCNTs) have been dispersed in acrylonitrile butadiene styrene (ABS) using a micro twin-screw extruder with back flow channel. The electrical and mechanical properties of MWCNTs in ABS with different wt% have been studied. Incorporation of only 3 wt. % MWCNTs in ABS leads to significant enhancement in the tensile strength (up to 69.4 MPa) which was equivalent to 29% increase over pure ABS. The effect of MWCNTs on the structural behaviour of ABS under tensile loading showed a ductile to brittle transition with increase concentration of MWCNTs. The results of enhanced mechanical properties were well supported by micro Raman spectroscopic and scanning electron microscopic studies. In addition to the mechanical properties, electrical conductivity of these composites increased from 10⁻¹² to 10⁻⁵ Scm⁻¹ showing an improvement of ∼7 orders of magnitude. Due to significant improvement in the electrical conductivity, EMI shielding effectiveness of the composites is achieved up to −39 dB for 10 wt. % loaded MWCNTs/ABS indicating the usefulness of this material for EMI shielding in the Ku-band. The mechanism of improvement in EMI shielding effectiveness is discussed by resolving their contribution in absorption and reflection loss. This material can be used as high-strength EMI shielding material.     

Structure and properties of highly oriented polyoxymethylene/multi-walled carbon nanotube composites produced by hot stretching

Highly-oriented polyoxymethylene (POM)/multi-walled carbon nanotube (MWCNT) composites were fabricated through solid hot stretching technology. With the draw ratio as high as 900%, the oriented composites exhibited much improved thermal conductivity and mechanical properties along the stretching direction compared with that of the isotropic samples before drawing. The thermal conductivity of the composite with 11.6 vol.% MWCNTs can reach as high as 1.2 W/m K after drawing. Microstructure observation demonstrated that the POM matrix had an ordered fibrillar bundle structure and MWCNTs in the composite tended to align parallel to the stretching direction. Wide-angle X-ray diffraction results showed that the crystal axis of the POM matrix was preferentially oriented perpendicular to the draw direction, while MWCNTs were preferentially oriented parallel to the draw direction. The strong interaction between the POM matrix and the MWCNTs hindered the orientation movement of molecules of POM, but induced the orientation movement of MWCNTs.     

Thermal conductive and electrical properties of polyurethane/hyperbranched poly(urea-urethane)-grafted multi-walled carbon nanotube composites

Hyperbranched poly(urea-urethane)-grafted multi-walled carbon nanotubes (HPU-MWCNTs) were incorporated in a polyurethane (PU) matrix based on poly(ethylene oxide-tetrahydrofuran) and aliphatic polyisocyanate resin as curing agent. The 9–12 nm thick HPU shell formed on the MWCNTs improved the dispersion of MWCNTs and enhanced the interfacial adhesion between the PU matrix and MWCNTs, leading to improvements in storage modulus and T_g of the composites and enhancement of the thermal stability of PU. Thus, composites with 0.5–1 wt% MWCNTs increased the thermal conductivity by about 60–70% when compared to, and retained the high electrical resistivity of, neat PU.     

Interconnected multi-walled carbon nanotubes reinforced polymer-matrix composites

A modified method for interconnecting multi-walled carbon nanotubes (MWCNTs) was put forward. And interconnected MWCNTs by reaction of acyl chloride and amino groups were obtained. Scanning electron microscopy shows that hetero-junctions of MWCNTs with different morphologies were formed. Then specimens of pristine MWCNTs, chemically functionalized MWCNTs and interconnected MWCNTs reinforced epoxy resin composites were fabricated by cast moulding. Tensile properties and fracture surfaces of the specimens were investigated. The results show that, compared with pristine MWCNTs and chemically functionalized MWCNTs, the chemically interconnected MWCNTs improved the fracture strain and therefore the toughness of the composites significantly.     

Development of conducting polychloroprene rubber using imidazolium based ionic liquid modified multi-walled carbon nanotubes

A simplified and an eco-friendly approach to develop polychloroprene rubber composites with high electrical conductivity is reported. The usage of room temperature ionic liquid, 1-butyl 3-methyl imidazolium bis(trifluoromethylsulphonyl)imide and a low concentration (5 phr) of commercial grade multi-walled carbon nanotubes (MWCNTs) in polychloroprene rubber exhibited an electrical conductivity of 0.1 S/cm with a stretchability >500%. The physical (cation-pi/pi-pi) interaction between the ionic liquid and the MWCNTs is evidenced by Raman spectroscopy. Transmission electron microscopy images exhibit an improved dispersion of the BMI modified tubes in matrix at various magnification scales. The dependency of dynamic properties on the concentration of ionic liquid at constant loading of nanotubes supports the fact that ionic liquid assists in the formation of filler-filler networks. The tensile modulus of 3 phr loaded modified MWCNT/CR composite is increased by 50% with regard to that of the unmodified MWCNT/CR composite. Mooney-Rivlin plot displays the existence of rubber-filler interactions.     

Effects of carbon nanotubes and carbon fiber reinforcements on thermal conductivity and ablation properties of carbon/phenolic composites

The ablation properties and thermal conductivity of carbon nanotube (CNT) and carbon fiber (CF)/phenolic composites were evaluated for different filler types and structures. It was found that the mechanical and thermal properties of phenolic-polymer matrix composites were improved significantly by the addition of carbon materials as reinforcement. The concentrations of CF and CNT reinforcing materials used in this study were 30 vol% and 0.5 wt%, respectively. The thermal conductivity and thermal diffusion of the different composites were observed during ablation testing, using an oxygen–kerosene (1:1) flame torch. The thermal conductivity of CF mat/phenolic composites was higher than that of random CF/phenolic composites. Both CF mat and CNT/phenolic composites exhibited much better thermal conductivity and ablation properties than did neat phenolic resin. The more conductive carbon materials significantly enhanced the heat conduction and dissipation from the flame location, thereby minimizing local thermal damage.     

Effects of grafted chain length on mechanical and electrical properties of nanocomposites containing polylactide-grafted carbon nanotubes

We herein report the effects of interfacial reinforcement on mechanical and electrical properties of nanocomposites based on polylactide (PLA) and multi-walled carbon nanotube (MWCNT). For this purpose, a series of MWCNTs grafted with PLA chains of various lengths (MWCNT-g-PLAs) were prepared by ring-opening polymerization of l-lactide with carboxylic acid-functionalized MWCNT (MWCNT-COOH). MWCNT-g-PLAs were then mixed with commercial PLA to obtain PLA/MWCNT-g-PLA nanocomposites with 1.0 wt.% MWCNT content. It was revealed that morphological, mechanical, and electrical properties of PLA/MWCNT-g-PLA nanocomposites were strongly dependent on the PLA chain length of MWCNT-g-PLAs. FE-SEM images exhibited that the nanocomposites containing MWCNT-g-PLA with longer PLA chain length exhibited better dispersion of MWCNTs in the PLA matrix. Initial moduli and tensile strengths of PLA/MWCNT-g-PLA composites increased with the increment of chain length of PLA grafted on MWCNTs, which attributes to the improved interfacial adhesion between the grafted PLA chains of MWCNT-g-PLA and the PLA matrix. As a result, the experimental initial modulus (2775 ± 193 MPa) of the nanocomposite including MWCNT-g-PLA with PLA chains of average molecular weight of 530 g/mol was quite close to the theoretical value (2911 MPa) predicted for the nanocomposite with perfect interfacial adhesion. Unexpectedly, electrical resistivities of PLA/MWCNT-g-PLA nanocomposites were found to increase from ∼10⁴ to ∼10¹² Ω/sq with increasing the PLA chain length of MWCNT-g-PLA, which is due to the fact that the PLA chains grafted on MWCNTs prevent the formation of the electrical conduction path of MWCNTs in the PLA matrix.     

Thermal and mechanical properties of phenolic-based composites reinforced by carbon fibres and multiwall carbon nanotubes

The thermal, mechanical and ablation properties of carbon fibre/phenolic composites filled with multiwall carbon nanotubes (MWCNTs) were investigated. Carbon fibre/phenolic/MWCNTs were prepared using different weight percentage of MWCNTs by compression moulding. The samples were characterized by scanning electron microscopy (SEM), flexural tests, thermal gravimetric analysis and oxyacetylene torch tests. The thermal stability and flexural properties of the nanocomposites increased by increasing MWCNTs content (wt% ⩽1), but they decreased when the content of MWCNTs was 2 wt%. The linear and mass ablation rates of the nanocomposites after modified with 1 wt% MWCNTs decreased by about 80% and 52%, respectively. To investigate the material post-test microstructure, a morphological characterization was carried out using SEM. It was shown that the presence of MWCNTs in the composite led to the formation of a strong network char layer without any cracks or opening.     

Synthesis of poly(3-hexylthiophene)-graft-poly(t-butyl acrylate-co-acrylic acid) and its role of compatibilizer for enhancement of mechanical and electrical properties of Nylon 66/multi-walled carbon nanotube composites

A compatibilizer, poly(3-hexylthiophene)-graft-poly(t-butyl acrylate-co-acrylic acid) was synthesized, where the acrylic aid was formed by hydrolysis of t-butyl acrylate unit. It has been identified that poly(3-hexylthiophene) backbone of the compatibilizer interacts with multi-walled carbon nanotubes (MWCNTs) via π–π interaction and the acrylic acid unit of the graft chain interacts with Nylon 66 (N66) matrix via hydrogen bonding. When a small amount of compatibilizer was added to N66/MWCNT composites, MWCNTs were more homogeneously dispersed in N66 matrix than the case without compatibilizer. As a consequence, mechanical and electrical properties of the composites with compatibilizer were largely improved as compared with those of composites without compatibilizer.     

Effect of size and shape of metal particles to improve hardness and electrical properties of carbon nanotube reinforced copper and copper alloy composites

Utilizing the extra-ordinary properties of carbon nanotube (CNT) in metal matrix composite (MMC) for macroscopic applications is still a big challenge for science and technology. Very few successful attempts have been made for commercial applications due to the difficulties incorporating CNTs in metals with up-scalable processes. CNT reinforced copper and copper alloy (bronze) composites have been fabricated by well-established hot-press sintering method of powder metallurgy. The parameters of CNT–metal powder mixing and hot-press sintering have been optimized and the matrix materials of the mixed powders and composites have been evaluated. However, the effect of shape and size of metal particles as well as selection of carbon nanotubes has significant influence on the mechanical and electrical properties of the composites. The hardness of copper matrix composite has improved up to 47% compared to that of pure copper, while the electrical conductivity of bronze composite has improved up to 20% compared to that of the pure alloy. Thus carbon nanotube can improve the mechanical properties of highly-conductive low-strength copper metals, whereas in low-conductivity high-strength copper alloys the electrical conductivity can be improved.     

Selective location and conductive network formation of multiwalled carbon nanotubes in polycarbonate/poly(vinylidene fluoride) blends

Multiwalled carbon nanotubes (MWCNTs)-filled polycarbonate (PC), poly(vinylidene fluoride) (PVDF) and PC/PVDF conductive composites were fabricated using melt mixing, respectively. The dynamic process of MWCNTs conductive network formation in the composites was in situ traced by recording the variation of electrical resistivity with time during annealing treatments. As a result, the percolation threshold for the MWCNTs-filled PC/PVDF system was much lower than those of MWCNTs-filled individual polymers and the MWCNTs were selectively located in the PC phase of PC/PVDF composite, which had been verified by scanning electron microscopy measurements. The activation energy of conductive network formation for PC/PVDF/MWCNTs composite was close to that of the PC/MWCNTs system, which further confirmed that MWCNTs were dispersed mainly in the PC phase. Furthermore, the assembly velocity of MWCNTs in the polymer melt increased with annealing temperature.     

Mechanical and electrical property improvement in CNT/Nylon composites through drawing and stretching

The excellent mechanical properties of carbon nanotubes (CNTs) make them the ideal reinforcements for high performance composites. The misalignment and waviness of CNTs within composites are two major issues that limit the reinforcing efficiency. We report an effective method to increase the strength and stiffness of high volume fraction, aligned CNT composites by reducing CNT waviness using a drawing and stretching approach. Stretching the composites after fabrication improved the ultimate strength by 50%, 150%, and 190% corresponding to stretch ratios of 2%, 4% and 7%, respectively. Improvement of the electrical conductivities exhibited a similar trend. These results demonstrate the importance of straightening and aligning CNTs in improving the composite strength and electrical conductivity.     

Mechanical,thermal and morphological characterization of cellulose fiber-reinforced phenolic foams

In this work, the compressive mechanical properties, thermal stability and morphology of cellulose fiber-reinforced phenolic foams were studied. The cellulose fiber-reinforced phenolic foam showed the greatest compressive mechanical properties by incorporating 2 wt.% of the reinforcement. The compressive modulus and strength of 2 wt.% cellulose fiber-reinforced phenolic foam were increased by 21% and 18%, respectively, relative to the unreinforced material. The addition of the cellulose fibers to the phenolic foam slightly decreased the thermal stability of the material. The study on the morphology of the cellulose-reinforced phenolic foams via Scanning electron microscopy (SEM) indicated a strong bonding between the fibers and phenolic matrix. In addition, the incorporation of the cellulose fibers into the foam resulted in a decreased cell size and increased cell density of the material. The incorporation of 2 wt.% of cellulose fibers into the phenolic foam led to obtain the material with the best features.     

Preparation,characterization and properties of polycaprolactone diol-functionalized multi-walled carbon nanotube/thermoplastic polyurethane composite

Multi-walled carbon nanotubes (MWCNTs) were chemically functionalized to prepare thermoplastic polyurethane (PU) composites with enhanced properties. In order to achieve a high compatibility of functionalized MWCNTs with the PU matrix, polycaprolactone diol (PCL), as one of PU’s monomers, was selectively grafted on the surface of MWCNTs (MWCNT–PCL), while carboxylic acid groups functionalized MWCNTs (MWCNT–COOH) and raw MWCNTs served as control. Both MWCNT–COOH and MWCNT–PCL improved the dispersion of MWCNTs in the PU matrix and interfacial bonding between them at 1 wt% loading fraction. The MWCNT–PCL/PU composite showed the greatest extent of improvement, where the tensile strength and modulus were 51.2% and 33.5% higher than those of pure PU respectively, without sacrificing the elongation at break. The considerable improvement in both mechanical properties and thermal stability of MWCNT–PCL/PU composite should result from the homogeneous dispersion of MWCNT–PCL in the PU matrix and strong interfacial bonding between them.     

Porous composites coated with hybrid nano carbon materials perform excellent electromagnetic interference shielding

This work reported preparation of porous composites using a simple dip-coating method, and the fabricated composites containing hybrid carbon nanomaterials performed excellent electromagnetic interference (EMI) shielding properties. A commercial sponge was coated with silver nanoparticles before being dip-coated with graphene (GP)/ink, multi-wall carbon nanotubes (MWCNTs)/ink, or hybrid GP/MWCNTs/ink to form Ag/carbon nanomaterial hybrid composites, and then the composites were subjected to EMI measurements in the frequency range of 0.45–1.5 GHz. For comparison, the sponges without Ag nanoparticle coating were also prepared. Herein, we found an insignificant difference in EMI SE among the porous composites without Ag nanoparticle coating, and the maximum values of approximately 14.4 dB was attained. Interestingly, the hybrid composites with Ag nanoparticle coating exhibited maximum EMI shielding of 24.33 dB. Due to their porous structure, the EMI SE measurements showed that reflection dominates the EMI SE for all the sponge composites studied in this work.     

Segregated poly(vinylidene fluoride)/MWCNTs composites for high-performance electromagnetic interference shielding

Conductive polymer composites (CPCs) that contain a segregated structure have attracted significant attentions because of their promising for fulfilling low filler contents with high electromagnetic interference (EMI) properties. In the present study, segregated poly(vinylidene fluoride) (PVDF)/multi-walled carbon nanotubes (MWCNTs) composites were successfully prepared by mechanical mixing and hot compaction. The PVDF/MWCNTs samples with 7 wt% filler content possess high electrical conductivities and high EMI shielding effectiveness (SE), reaching 0.06 S cm⁻¹ and 30.89 dB (in the X-band frequency region), much higher than lots of reported results for CNT-based composites. And the EMI SE greatly increased across the frequency range as the sample thickness was improved from 0.6 to 3.0 mm. The EMI shielding mechanisms were also investigated and the results demonstrated absorption dominating shielding mechanism in this segregated material. This effective preparation method is simple, low-cost, and environmentally-friendly and has potential industrial applications in the future.     

Modification of surface functionality of multi-walled carbon nanotubes on fracture toughness of basalt fiber-reinforced composites

In this work, we studied the influence of surface functionality of multi-walled carbon nanotubes (MWCNTs) on the mechanical properties of basalt fiber-reinforced composites. Acid and base values of the MWCNTs were determined by Boehm's titration technique. The surface properties of the MWCNTs were determined FT-IR, and XPS. The mechanical properties of the composites were assessed by measuring the interlaminar shear stress, fracture toughness, fracture energy, and impact strength. The chemical treatments led to a change of the surface characteristics of the MWCNTs and of the mechanical interfacial properties of MWCNTs/basalt fibers/epoxy composites. Especially the acid-treated MWCNTs/basalt fibers/epoxy composites had improved mechanical properties compared to the base-treated and non-treated MWCNTs/basalt fibers/epoxy composites. These results can probably be attributed to the improved interfacial bonding strength resulting from the improved dispersion and interfacial adhesion between the epoxy resin and the MWCNTs.     

Microstructure changes of polyurethane by inclusion of chemically modified carbon nanotubes at low filler contents

The surface of multi-walled carbon nanotubes (MWCNTs) was modified to introduce acidic groups in either covalent or van der Waals interaction bonding environments to establish cross-linking sites with a host polymer. Nanocomposites based on a polyurethane matrix (PU) containing chemically functionalised multi-walled carbon nanotubes (MWCNTs) have been shown to alter its mechanical performance depending on the nature of the surface functional groups on MWCNTs, which correlates to the type of bonding interaction of the surface group and also the dispersibility of MWCNTs and their influence on the domain structure of polyurethane. The stress at break for nanocomposites containing 0.25 wt% of acid-oxidised MWCNTs (MWCNT-ox), bearing covalently attached carboxylic, lactone and phenolic groups, was twice that of the native PU and Young’s Modulus for the nanocomposites increased by four times. Whereas when hemin, which contains carboxylic functionality, was immobilised to the surface of pure MWCNTs, the improvement in Young’s Modulus was only around twice that of pure PU. Differences in the disaggregation of MWCNTs into PU were observed between the samples as well as variation of the native domain structure of PU. The results also infer that the purification of MWCNTs from acid-oxidative lattice fragments (fulvic acids) is vital prior to conducting surface chemistry and polymerisation in order to ensure maximum mechanical performance enhancement in their reinforcement of the host polymer.     

The poly(urethane-ionic liquid)/multi-walled carbon nanotubes composites

In the paper, a novel kind of imidazolium based poly(urethane-ionic liquid)/multi-walled carbon nanotubes (PUIL/MWCNT) composites was facilely prepared by uncovalent ways. The imidazolium based ionic liquid (IL) greatly improved the dispersion of pristine MWCNTs in PUIL by the π-cation interaction formed between the imidazolium cation and the π-electron of MWCNTs. The PUIL/MWCNT composites showed obviously increased modulus, glass transition temperature and tensile strength in comparison with PU/MWCNT composites. The thermal and mechanical properties of the PUIL/MWCNT composites presented significant increase with low load of the MWCNTs. It indicated the interactions between PUIL and MWCNTs played an important role to enhance the performances of the composites.     

Multi-walled carbon nanotube/nanostructured zirconia composites: Outstanding mechanical properties in a wide range of temperature

Multi-walled carbon nanotube (MWCNT)/nanostructured zirconia composites with a homogenous distribution of different MWCNT quantities (ranging within 0.5-5 wt.%) were developed. By using Spark Plasma Sintering we succeeded in preserving the MWCNTs firmly attached to zirconia grains and in obtaining fully dense materials. Moreover, MWCNTs reduce grain growth and keep a nanosize structure. A significant improvement in room temperature fracture toughness and shear modulus as well as an enhanced creep performance at high temperature is reported for the first time in this type of materials. To support these interesting mechanical properties, high-resolution electron microscopy and mechanical loss measurements have been carried out. Toughening and creep hindering mechanisms are proposed. Moreover, an enhancement of the electrical conductivity up to 10 orders of magnitude is obtained with respect to the pure ceramics.