A graded-gap photoelectric detector for ionizing radiation

A heterostructure consisting of a graded-gap p-Al_xGa_1?xAs layer on an n-GaAs substrate is studied in relation to its role as a photoelectric-response detector of X-ray photons and α particles. It is found that the current-power sensitivity of the detector is as high as 0.13 A/W and the voltage-power sensitivity exceeds 10⁶ V/W. The effect of preliminary irradiation with 5.48-MeV α particles (²⁴¹Am) on the detector’s sensitivity is studied. It is established that the detector’s sensitivity is reduced by a factor of 1.5–2 after irradiation with α particles at a dose of 5 × 10⁹ cm^?2. A further increase in the radiation dose to 4 × 10¹⁰ cm^?2 does not affect the detector’s sensitivity.     

Effective electron mass in a Mn<Subscript>x</Subscript>Hg<Subscript>1−<Emphasis Type="Italic">x</Emphasis></Subscript>Te system

The reflection spectra of n-Mn_xHg_1?xTe single crystals and epitaxial layers were measured at 300 K. The effective electron mass was determined for the samples with x=0.06–0.10 and an electron concentration N>6×10¹⁶ cm^?3. The calculated values of effective electron mass are close to experimental values.     

Role of Si-doped Al<Subscript>0.3</Subscript>Ga<Subscript>0.7</Subscript>As layers in the high-frequency conductivity of GaAs/Al<Subscript>0.3</Subscript>Ga<Subscript>0.7</Subscript>As heterostructures under conditions of the quantum hall effect

The complex high-frequency conductivity of GaAs/Al_0.3Ga_0.7As heterostructures that are δ-doped and modulation-doped with silicon was investigated by acoustic methods under conditions of the integer quantum Hall effect. Both the real (σ₁) and imaginary (σ₂) parts of the complex conductivity σ(ω, H)=σ_i?iσ₂ were determined from the dependences of the absorption and velocity of surface acoustic waves on magnetic field. It is shown that, in the heterostructures with electron density n_s=(1.3–7)×10¹¹ cm^?2 and mobility μ=(1–2)×10⁵ cm²/(V s), the high-frequency conductivity near the centers of the Hall plateau is due to electron hopping between localized states. It is established that, with filling numbers 2 and 4, the conductivity of the Al_0.3Ga_0.7As:Si layer efficiently shunts the high-frequency hopping conductivity of the two-dimensional interface layer. A method of separating the contributions of the interface and Al_0.3Ga_0.7As:Si layers to the hopping conductivity σ(ω, H) is developed. The localization length of electrons in the interface layer is determined on the basis of the nearest neighbor hopping model. It is shown that, near the centers of the Hall plateau, both σ(ω, H) and n_s depend on the cooling rate of a GaAs/Al_0.3Ga_0.7As sample. As a result, the sample “remembers” the cooling conditions. Infrared light and static strain also change both σ(ω, H) and n_s. We attribute this behavior to the presence of two-electron defects (so-called DX^? centers) in the Al_0.3Ga_0.7As:Si layer.     

Population inversion between Γ subbands in quantum wells under the conditions of Γ-<Emphasis Type="Italic">L</Emphasis> intervalley transfer

Monte Carlo simulations of electron transport in Al_xGa_1−x As/GaAs/In_yGa_1−y As double-quantum-well heterostructures in high lateral electric fields are carried out. It is shown that, under the conditions of intervalley Γ-L electron transfer, there exists a population inversion between the first and the second quantum-confinement subbands in the Γ valley. The population inversion appears in the fields exceeding 4 and 5.5 kV/cm at 77 and 300 K, respectively. The gain in a superlattice composed of such quantum wells is estimated to be on the order of 100 cm⁻¹ for radiation with a wavelength of 12.6 μm. __________ Translated from Fizika i Tekhnika Poluprovodnikov, Vol. 37, No. 2, 2003, pp. 224–229. Original Russian Text Copyright ? 2003 by Aleshkin, Andronov, Dubinov.     

1 550 nm long-wavelength vertical-cavity surface emitting lasers

A 1 550 nm long-wavelength vertical cavity surface emitting laser (VCSEL) on InP substrate is designed and fabricated. The transfer matrix is used to compute reflectivity spectrum of the designed epitaxial layers. The epitaxial layers mainly consist of 40 pairs of n-AlxGayIn(1-x-y)As/InP, and 6 strain compensated AlxGayIn(1-x-y)As/InP quantum wells on n-InP substrate, respectively. The top distributed Bragg reflection (DBR) mirror system has been formed by fabricating 4.5 pairs of SiO2/Si. The designed cavity mode is around 1 536 nm. The dip of the fabricated cavity mode is around 1 530 nm. The threshold current is 30 mA and the maximum output power is around 270 μW under CW operation at room temperature.     

Method for narrowing the directional pattern of an InGaAs/GaAs/AlGaAs multiwell heterolaser

A semiconductor laser with a new waveguide is developed. It allows significant narrowing of the directional pattern (to 4° in the plane perpendicular to the p–n junction). In the used waveguide, the minimum excess of the effective refractive index n_eff of the excitation mode over the substrate refractive index n_s (n_eff–n_s ? 1) is provided by selecting the thickness of Al_0.3Ga_0.7As confinement layers, which significantly increases the waveguide mode size and leads to directional-pattern narrowing.     

High-efficiency dual-junction GaInP/GaAs tandem solar cells obtained by the method of MOCVD

Monolithic dual-junction GaInP/GaAs solar cells grown by the MOCVD method were studied. The conditions of the growth of ternary Ga _x In_1?x P and Al _x In_1?x P alloys lattice-matched to GaAs are optimized. Technology for fabrication of a tunneling diode with a high peak current density of 207 A/cm² on the basis of heavily doped n ⁺⁺-GaAs:Si and p ⁺⁺-AlGaAs:C layers is developed. Cascade GaInP/GaAs solar cells obtained as a result of relevant studies featuring a good efficiency of the solar-energy conversion both for space and terrestrial applications. The maximum value of the GaInP/GaAs solar-cell efficiency was 30.03% (at AM1.5D, 40 suns).     

Thermoelectric figure of merit in solid solutions with phonon scattering by off-center impurities

The Seebeck coefficient and the electrical and thermal conductivities (S, σ, and κ) of ternary PbTe_1?xSe_x (x=0.1 and 0.3) and quaternary PbTe_1?2xSe_xS_x (x=0.025, 0.05, 0.1, and 0.15) solid solutions have been studied. Polycrystalline samples with an electron density of (0.5–5.0)×10¹⁸ cm^?3 were used; their quality was monitored by comparing the measured and calculated mobility values at 85 K. A considerable decrease in mobility and an anomalous trend in the σ(T) curve near 77 K were revealed in quaternary alloys with x?0.1; for x=0.15, unusual behavior of κ(T) was also found. According to estimates, the lattice thermal conductivity of this material is temperature-independent in the 80-to 300-K temperature range. This means that a reduction in phonon-phonon scattering with an increase in temperature is completely compensated by an increase in the scattering on impurities. The observed anomalies of σ(T) and κ(T) are considered assuming the possible of off-center location of sulfur atoms at the lattice sites. The thermoelectric figure of merit Z of the studied alloys has been determined in the range 80–300 K. In spite of decreasing mobility, the maximum Z was obtained in a quaternary compound with x=0.1: at 300 K, Z_max=2×10^?3 K^?1 with a carrier density of ～3×10¹⁸ cm^?3; at 175 K, Z_max=1.5×10^?3 K^?1 with the density decreasing to 5×10¹⁷ cm^?3. The obtained data indicate that the introduction of off-center impurities rises Z at T?300 K.     

Iodine Doping of CdTe and CdMgTe for Photovoltaic Applications

Iodine-doped CdTe and Cd_1?x Mg _x Te layers were grown by molecular beam epitaxy. Secondary ion mass spectrometry characterization was used to measure dopant concentration, while Hall measurement was used for determining carrier concentration. Photoluminescence intensity and time-resolved photoluminescence techniques were used for optical characterization. Maximum n-type carrier concentrations of 7.4 × 10¹⁸ cm^?3 for CdTe and 3 × 10¹⁷ cm^?3 for Cd_0.65Mg_0.35Te were achieved. Studies suggest that electrically active doping with iodine is limited with dopant concentration much above these values. Dopant activation of about 80% was observed in most of the CdTe samples. The estimated activation energy is about 6 meV for CdTe and the value for Cd_0.65Mg_0.35Te is about 58 meV. Iodine-doped samples exhibit long lifetimes with no evidence of photoluminescence degradation with doping as high as 2 × 10¹⁸ cm^?3, while indium shows substantial non-radiative recombination at carrier concentrations above 5 × 10¹⁶ cm^?3. Iodine was shown to be thermally stable in CdTe at temperatures up to 600°C. Results suggest iodine may be a preferred n-type dopant compared to indium in achieving heavily doped n-type CdTe.     

Electrical properties of silicon layers implanted with erbium and oxygen ions in a wide dose range and thermally treated in different temperature conditions

The electrical properties of silicon implanted with Er and O ions in a wide dose range have been studied. The dependence of electron mobility on the concentration of electrically active centers is determined for Si:Er layers with Er concentrations in the range of 9×10¹⁵–8×10¹⁶ cm^?3. Sharp bends related to specific features of Er segregation in solid-phase epitaxial recrystallization are observed in the concentration profiles of electrically active centers, n(x), and Er atoms, C(x), at Er ion implantation doses exceeding the amorphization threshold. The n(x) and C(x) profiles virtually coincide near the surface. A linear rise in the maximum concentration of electrically active centers at approximately constant effective coefficient of their activation, k, is observed at Er implantation doses exceeding the amorphization threshold. At an Er concentration higher than 7×10¹⁹ cm^?3, the concentration of electrically active centers levels off and k decreases.     

Resonant Raman scattering and atomic force microscopy of InGaAs/GaAs multilayer nanostructures with quantum dots

The transition from two-dimensional (2D) pseudomorphic growth to the three-dimensional (3D) (nanoisland) growth in In_xGa_1?xAs/GaAs multilayer structures grown by molecular-beam epitaxy was investigated by atomic force microscopy, photoluminescence, and Raman scattering. The nominal In content x in In_xGa_1?xAs was varied from 0.20 to 0.50. The thicknesses of the deposited In_xGa_1?xAs and GaAs layers were 14 and 70 monolayers, respectively. It is shown that, at these thicknesses, the 2D-3D transition occurs at x ≥ 0.27. It is ascertained that the formation of quantum dots (nanoislands) does not follow the classical Stranski-Krastanov mechanism but is significantly modified by the processes of vertical segregation of In atoms and interdiffusion of Ga atoms. As a result, the In_xGa_1?xAs layer can be modeled by a 2D layer with a low In content (x < 0.20), which undergoes a transition into a thin layer containing nanoislands enriched with In (x > 0.60). For multilayer In_xGa_1?xAs structures, lateral alignment of quantum dots into chains oriented along the \([\overline 1 10]\) direction can be implemented and the homogeneity of the sizes of quantum dots can be improved.     

A 4<Emphasis Type="Italic">H</Emphasis>-SiC<Emphasis Type="Italic">p-i-n</Emphasis> diode fabricated by a combination of sublimation epitaxy and CVD

The possibility of fabricating heavily doped (N _a ?N _d ≥ 1 × 10¹⁹ cm_?3) p⁺-4H-SiC layers on CVD-grown lightly doped n-4H-SiC layers by sublimation epitaxy has been demonstrated. It is shown that a Au/Pd/Ti/Pd contact, which combines a low specific contact resistance (～2 × 10^?5 Ω cm²) with high thermal stability (up to 700°C), is the optimal contact to p-4H-SiC. The p-n structures obtained are used to fabricate packaged diodes with a breakdown voltage of up to 1400 V.     

Characterization of HgCdTe Films Grown on Large-Area CdZnTe Substrates by Molecular Beam Epitaxy

Recent advances in growth of Hg_1?x Cd _x Te films on large-area (7 cm × 7.5 cm) CdZnTe (CZT) substrates is presented. Growth of Hg_1?x Cd _x Te with good uniformity on large-area wafers is achieved using a Riber 412 molecular beam epitaxy (MBE) tool designed for growth of Hg_1?x Cd _x Te compounds. The reactor is equipped with conventional CdTe, Te, and Hg sources for achieving uniform exposure of the wafer during growth. The composition of the Hg_1?x Cd _x Te compound is controlled in situ by employing a closed-loop spectral ellipsometry technique to achieve a cutoff wavelength (λ _co) of 14 μm at 78 K. We present data on the thickness and composition uniformity of films grown for large-format focal-plane array applications. The composition and thickness nonuniformity are determined to be <1% over the area of a 7 cm × 7.5 cm wafer. The films are further characterized by Fourier-transform infrared spectroscopy, optical microscopy, and Hall measurements. Additionally, defect maps show the spatial distribution of defects generated during the epitaxial growth of the Hg_1?x Cd _x Te films. Microdefect densities are in the low 10³ cm^?2 range, and void defects are below 500 cm^?2. Dislocation densities less than 5 × 10⁵ cm^?2 are routinely achieved for Hg_1?x Cd _x Te films grown on CZT substrates. HgCdTe 4k × 4k focal-plane arrays with 15 μm pitch for astronomical wide-area infrared imagers have been produced using the recently developed MBE growth process at Teledyne Imaging Sensors.     

Spin effects in magnetoresistance induced in an <Emphasis Type="Italic">n</Emphasis>-In<Subscript>x</Subscript>Ga<Subscript>1−<Emphasis Type="Italic">x</Emphasis></Subscript>As/GaAs double quantum well by a parallel magnetic field

Magnetoresistance in n-In_xGa_1?xAs/GaAs (x ≈ 0.18) heterostructures with double quantum wells (DQWs) was studied in the magnetic field parallel to the DQW layer. Specific features of the magnetoresistance, related to the passing of the tunnel gap edges across the Fermi level, are revealed and studied. Agreement between the calculated and experimental positions of the observed features is obtained when the spin splitting of the energy spectrum is taken into account. Earlier, similar features were observed in the magnetoresistance of n-GaAs/Al_xGa_1?xAs DQW heterostructures, but the spin effects did not manifest themselves.     

Superradiance in quantum heterostructures

Dependences of spectra, intensity, and relaxation time of superradiance in GaAs/In_xGa_1?xAs/GaAs quantum heterostructures on the excitation power density in the range of 1×10^?3–1×10⁶ W/cm² are investigated. It is shown for the first time that filling of the quantum well affects all spectral characteristics of superradiance.     

Investigation of the ZnS-CdHgTe interface

The ZnS-Cd_xHg_1?xTe interface was investigated using the capacitance-voltage characteristics of MIS structures in experimental samples. During fabrication of the n⁺-p junctions based on p-Cd_xHg_1?xTe, the density of states within the range N _ss =(1–6)×10¹¹ cm^?2 eV^?1 at T=78 K was obtained. The experiments showed that the conditions in which n⁺-p junctions are fabricated only slightly affect the state of the ZnS-CdHgTe interface. The negative voltages of the at bands V _FB , even if immediately after deposition of the ZnS films V _FB >0, point to the enrichment of the ZnS-p-CdHgTe near-surface layer with majority carriers, specifically, holes. This led to a decrease in the leakage current over the surface. During long-term storage (as long as ～15 years) in air at room temperature, no degradation of differential resistance R _d , current sensitivity S _i , and detectivity D* of such n⁺-p junctions with a ZnS protection film was observed.     

Interaction of charge carriers with the localized magnetic moments of manganese atoms in <Emphasis Type="Italic">p</Emphasis>-GaInAsSb/<Emphasis Type="Italic">p</Emphasis>-InAs:Mn heterostructures

Transport properties of p-Ga_1?xIn_xAs_ySb_1?y/p-InAs:Mn heterostructures with undoped layers of solid solutions similar in composition to GaSb (x?0.22) grown by liquid-phase epitaxy on substrates with a Mn concentration of (5–7)×10¹⁸ cm^?3 are studied. It is ascertained that there is an electron channel at the interface (from the InAs side). The anomalous Hall effect and negative magnetoresistance are observed at relatively high temperatures (77–200) K. These phenomena can be attributed to the s-d-exchange interaction between Mn ions of the substrate and s electrons of the two-dimensional channel. The effective magnetic moment of Mn ions was evaluated as μ=200µ_B at T=77 K.     

Vegard’s law and superstructural phases in Al<Subscript>x</Subscript>Ga<Subscript>1−<Emphasis Type="Italic">x</Emphasis></Subscript>As/GaAs(100) epitaxial heterostructures

The lattice constants of Al_xGa_1?x As epitaxial alloys with various AlAs (x) contents are determined for AlxGa_1?xAs/GaAs(100) heterostructures grown by MOC-hydride epitaxy using X-ray diffractometry and an X-ray back-reflection method. An ordered AlGaAs₂ (superstructural) phase is found in epitaxial heterostructures with x ≈ 0.50. The lattice constant of this phase is smaller than the lattice constants of an Al_0.50Ga_0.50As alloy and GaAs single-crystal substrate.     

Investigation of MBE-Growth of Mid-Wave Infrared Hg<Subscript>1−<Emphasis Type="Italic">x</Emphasis></Subscript>Cd<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>Se

Undoped mid-wave infrared Hg_1?xCd_xSe epitaxial layers have been grown to a nominal thickness of 8–14 μm on GaSb (211)B substrates by molecular beam epitaxy (MBE) using constant beam equivalent pressure ratios. The effects of growth temperature from 70°C to 120°C on epilayer quality and its electronic parameters has been examined using x-ray diffraction (XRD) rocking curves, atomic force microscopy, Nomarski optical imaging, photoconductive decay measurements, and variable magnetic field Hall effect analysis. For samples grown at 70°C, the measured values of XRD rocking curve full width at half maximum (FWHM) (116 arcsec), root mean square (RMS) surface roughness (2.7 nm), electron mobility (6.6?×?10⁴ cm² V^?1 s^?1 at 130 K), minority carrier lifetime (～?2 μs at 130 K), and background n-type doping (～?3?×?10¹⁶ cm^?3 at 130 K), indicate device-grade material quality that is significantly superior to that previously published in the open literature. All of these parameters were found to degrade monotonically with increasing growth temperature, although a reasonably wide growth window exists from 70°C to 90°C, within which good quality HgCdSe can be grown via MBE.     

Improvement in Thermoelectric Performance of SnS Due to Electronic Structure Modification Under Biaxial Strain

Ab-initio calculations using the full potential linearized augmented plane-wave technique and the semi-classical Boltzmann theory are used to study thermoelectric properties of unstrained SnS and at 1%, 2% and 3% applied biaxial tensile (BT) strain. The studies are carried out at 800 K for p-type and n-type carriers. For an increase in BT strain, lattice constants of SnS change causing changes in the band structure and increase in the band gap which in turn modifies thermoelectric coefficients. In the case of unstrained SnS, the maximum thermopower (S) obtained is 426 μV/K at carrier concentration 5.40?×?10¹⁸ cm^?3 for p-type carriers and 435 μV/K at carrier concentration 1.68?×?10¹⁸ cm^?3 for n-type carriers. At 3% applied BT strain, S is increased to 696 μV/K at carrier concentration 4.61?×?10¹⁷ cm^?3 for p-type carriers and 624 μV/K at carrier concentration 3.21?×?10¹⁷ cm^?3 for n-type carriers. The power factor (PF) increases?～?2 times at 3% BT strain as compared to unstrained SnS, and it is 6.20 mW K^?2 m^?1 for p-type carriers. For n-type carriers, PF at 3% applied BT is slightly less than the PF for unstrained SnS, which is 6.81 mW K^?2 m^?1. For both types of carriers, the figure of merit (ZT) is found to be?～?1.5 for unstrained SnS. For p-type carriers ZT is enhanced 1.4 times at 3% applied BT strain as compared to that of unstrained SnS. However, for n-type carriers, ZT does not change drastically with increase in BT strain.