High-Temperature Failure Mechanisms of Hot-Pressed Si3N4 and Si3N4/Si3N4-Whisker-Reinforced Composites

The high-temperature flexural strength of hot-pressed silicon nitride (Si₃N₄) and Si₃N₄-whisker-reinforced Si₃N₄-matrix composites has been measured at a crosshead speed of 1.27 mm/min and temperatures up to 1400°C in a nitrogen atmosphere. Load–displacement curves for whisker-reinforced composites showed nonelastic fracture behavior at 1400°C. In contrast, such behavior was not observed for monolithic Si₃N₄. Microstructures of both materials have been examined by scanning and transmission electron microscopy. The results indicate that grain-boundary sliding could be responsible for strength degradation in both monolithic Si₃N₄ and its whisker composites. The origin of the nonelastic failure behavior of Si₃N₄-whisker composite at 1400°C was not positively identified but several possibilities are discussed.     

Properties of Si3N4 Produced by Nitriding Slip-Cast Si Containing Si3N4 Grog Additions

The properties of Si₃N₄ compositions produced by nitriding slip-cast Si bodies containing up to 16% Si₃N₄ grog were determined. The introduction of grog consistently lowered the densities, the room- and high-temperature strengths, and the resistance to oxidation. The open structure of the grog-containing mixes favored low-temperature gas-phase reactions leading to α-Si₃N₄ formation. In higher-density compositions containing predominantly Si, gas-liquid-solid reactions at higher temperatures produced a relatively greater content of the β phase.     

Hot Isostatic Pressing of Si3N4 Powder Compacts and Reaction-Bonded Si3N4

Hot isostatically pressed silicon nitride was produced by densifying Si₃N₄ powder compacts and reaction-bonded Si₃N₄ (RBSN) parts with yttria as a sintering additive. The microstructure was analyzed using scanning electron microscopy, X-ray diffraction, and density measurements. The influence of the microstructure on fracture strength, creep, and oxidation behavior was investigated. It is assumed that the higher amount of oxygen in the Si₃N₄ starting powder compared with the RBSN starting material leads to an increased amount of liquid phase during densification. This results in grain growth and in a larger amount of grain boundary phase in the hot isostatically pressed material. Compared with the hot isostatically pressed RBSN samples therefore, strength decreases whereas the creep rate and the weight gain during oxidation increase.     

Synthesis of Si3N4 with Emphasis on Si-S-N Chemistry

Industrial production of Si₃N₄ from SiCI₄, is increasing. An element rivaling CI in abundance and cheapness with potentially suitable chemistry for this application is sulfur. Thus, Si–S–N chemistry was investigated to determine its usefulness in producing Si₃N₄. Bifunctionality in S, as opposed to mono-functionality in CI, may allow special routes via polymers to become important.     

Pressureless Sintering of Dense Si3N4 and Si3N4/SiC Composites with Nitrate Additives

The effect of aluminum and yttrium nitrate additives on the densification of monolithic Si₃N₄ and a Si₃N₄/SiC composite by pressureless sintering was compared with that of oxide additives. The surfaces of Si₃N₄ particles milled with aluminum and yttrium nitrates, which were added as methanol solutions, were coated with a different layer containing Al and Y from that of Si₃N₄ particles milled with oxide additives. Monolithic Si₃N₄ could be sintered to 94% of theoretical density (TD) at 1500°C with nitrate additives. The sintering temperature was about 100°C lower than the case with oxide additives. After pressureless sintering at 1750°C for 2 h in N₂, the bulk density of a Si₃N₄/20 wt% SiC composite reached 95% TD with nitrate additives.     

Comparison of Tribological Behavior Between α-Sialon/Si3N4 and Si3N4/Si3N4 Sliding Pairs in Water Lubrication

We report here the study on tribological behavior of α-Sialon in aqueous medium. The results derived from a wide range of test conditions are briefly discussed. A reduction in friction coefficient from 0.7 to 0.03 and a decrease in wear rate by two orders of magnitude were achieved under low load (9.8 N) and high speed (>0.54 m/s) conditions. The tribological behavior of α-Sialon/Si₃N₄ ceramics was then compared with Si₃N₄/Si₃N₄ tribopairs.     

Combustion Synthesis of Si3N4–SiC Composite Powders

Fine Si₃N₄-SiC composite powders were synthesized in various SiC compositions to 46 vol% by nitriding combustion of silicon and carbon. The powders were composed of α-Si₃N₄, β-Si₃N₄, and β-SiC. The reaction analysis suggested that the SiC formation is assisted by the high reaction heat of Si nitridation. The sintered bodies consisted of uniformly dispersed grains of β-Si₃N₄, β-SiC, and a few Si₂N₂O.     

Hot-Pressing Behavior of Si3N4

The densification behavior of Si₃N₄ containing MgO was studied in detail. It was concluded that MgO forms a liquid phase (most likely a magnesium silicate). This liquid wets and allows atomic transfer of Si₃N₄. Evidence of a second-phase material between the Si₃N₄ grains was obtained through etching studies. Transformation of α- to β-Si₃N₄ during hot-pressing is not necessary for densification.     

Synthesis of Porous Si3N4 Ceramics with Rod-Shaped Pore Structure

Porous Si₃N₄ ceramics were synthesized by pressureless sintering of green compacts prepared using slip casting of slurries containing Si₃N₄, 5 wt% Y₂O₃+2 wt% Al₂O₃, and 0–60% organic whiskers composed of phenol–formaldehyde resin with solids loading up to 60 wt%. Rheological properties of slurries were optimized to achieve a high degree of dispersion with a high solid-volume fraction. Samples were heated at 800°C in air and sintered at 1850°C in a N₂ atmosphere. Porosities ranging from 0% to 45% were obtained by the whisker contents (corresponding to 0–60 vol% whisker). Samples exhibited a uniform pore distribution. Their rod-shaped pore morphology originated from burnout of whiskers, and an extremely dense Si₃N₄ matrix.     

Impurity Phases in Hot-Pressed Si3N4

Impurity phases in commercial hot-pressed Si₃N₄ were investigated using transmission electron microscopy. In addition to the dominant, β-Si₃N₄ phase, small amounts of Si₂N₂O, SiC, and WC were found. Significantly, a continuous grain-boundary phase was observed in the ∼ 25 high-angle boundaries examined. This film is ∼ 10 Å thick between, β-Si₃N₄ grains and ∼ 30 Å thick between Si₂N₂O and β-Si₃N₄ grains.     

Facile Synthesis of Si3N4 Nanocrystals Via an Organic–Inorganic Reaction Route

Silicon nitride (Si₃N₄) nanocrystals were synthesized at about 250°C by a simple organic–inorganic reaction between CH₃SiCl₃ and NaN₃. The yield of Si₃N₄ is no <70 wt% based on the amount of precursor CH₃SiCl₃ used in the reaction and TGA analysis. X-ray diffraction indicates the formation of a mixture of α- and β-Si₃N₄. Particles with size from 40 to 100 nm are dominant in the products examined by transmission electron microscopy. X-ray photoelectron spectroscopy gives an atomic ratio of Si:N around 0.75:1. The formation of nanocrystalline Si₃N₄ during the organic–inorganic reaction goes through an intermediate product of NaSi₂N₃, which is important for understanding the reaction mechanism.