Influence of oxygen pressure on Nd:LuVO4 films grown by pulsed laser deposition

High quality Nd-doped lutecium vanadate thin films on silica glass substrates were fabricated successfully by using a pulsed laser deposition technique. The properties of the samples were characterized by using X-ray diffraction, Rutherford backscattering, atomic force microscopy (AFM), and prism-coupling measurements. The RBS shows that the ratio of Lu/V in the film is 0.991, which is in good agreement with the target composition. X-ray diffraction results show that the degree of crystal orientation along (2 0 0) increases with increasing oxygen pressure up to 20 Pa. The refractive indices of the films determined with dark-mode prism coupling measurements are slight, smaller than that of the bulk crystal. An optimum 20 Pa oxygen pressure, at which the oxygen was leaked into the chamber as the reactive ambient, was determined.     

Composition, structural and electrical properties of thin films prepared by laser ablation of neodymium-doped potassium gadolinium tungstate

Thin films were grown on (001) SiO₂, SiO₂/(100) Si or (100) MgO substrates by laser ablation of neodymium-doped potassium gadolinium tungstate (Nd:KGW) single crystal target. The films were deposited at temperatures between room temperature and 750 °C and pressures between 1 × 10^− 4 Pa and 50 Pa of oxygen ambient. The influence of the deposition conditions on the composition, structure, morphology and electrical properties of the films was investigated. Special attention was paid to the films deposited in vacuum (1 × 10^− 4 Pa) or at very low oxygen pressures. Under such conditions, the potassium (K), gadolinium (Gd) and oxygen (O) content decreased strongly as the temperature was increased. At room temperature, the films were K and O stoichiometric, in contrast with Gd, which showed a concentration twice higher. The films were polycrystalline, with the exception of those deposited at temperatures below 500 °C, which were amorphous. However, all were smooth and dense. The films grown in vacuum and at temperatures between 500 and 700 °C consist mainly of “â-tungsten” - tungsten oxide (W₃O) phase. The films grown on SiO₂/Si possessed the best surface quality with nano-size relief. The resistivity measurements as a function of the temperature showed that the films produced in vacuum and at temperatures below 500 °C were highly insulating, whereas at 600 °C they exhibited semiconducting behavior or a metallic one at 700 °C. This behavior can be attributed to the existence of various valence states for tungsten below W⁶⁺ in the films and to their crystal structure.     

Growth temperature dependent dielectric properties of BiFeO3 thin films deposited on silica glass substrates

We have studied the dependence of dielectric properties on the deposition temperature of BiFeO₃ thin films grown by the pulsed laser deposition technique. Thin films have been grown onto amorphous silica glass substrates with pre-patterned Au in-plane capacitor structures. It is shown that on the amorphous glass substrate, BiFeO₃ films with a near-bulk permittivity of 26 and coercive field of 80 kV/cm may be grown at a deposition temperature of about 600 °C and 1 Pa oxygen pressure. Low permittivity and higher coercive field of the films grown at the temperatures below and above 600 °C are associated with an increased amount of secondary phases. It is also shown that the deposition of BiFeO₃ at low temperature (i.e. 500 °C) and post deposition ex-situ annealing at elevated temperature (700 °C) increases the permittivity of a film. The applied bias and time dependence of capacitance of the films deposited at 700 °C and ex-situ annealed films are explained by the de-pinning of the ferroelectric domain-walls.     

Study of manganese oxide thin films grown by pulsed laser deposition

In this paper, we report on the growth of manganese oxides thin films by Pulsed Laser Deposition using an MnO target at various oxygen pressures and substrate temperatures ranging from 550 to 800 °C. Grazing Incidence X-Ray Diffraction measurements on the grown films revealed that, at low deposition temperature, the dominant phase is Mn₂O₃, but as the deposition temperature was raised above 700 °C, a phase transformation occurred leading to the formation of Mn₃O₄. In a qualitative comparison, in the temperature range of 500-850 °C, and at a pressure below 13 Pa, the phase diagram of bulk manganese oxides and our grown films show a fair correlation. The films grown near the transition temperature (T = 700 °C) were found to be very thin compared to those grown at lower or higher temperatures, but the surface roughness was found to increase with temperature, as determined by Atomic Force Microscopy.     

Anomalous behavior in ZnMgO thin films deposited by sol-gel method

The magnesium doped zinc oxide is a promising optical material to enhance the luminescence for possible application in solid state lighting. Magnesium doped zinc oxide thin films (Zn_0.85Mg_0.15O) were deposited by sol-gel route on p-type silicon and annealed at different temperatures in oxygen environment for an hour. The doping of magnesium in zinc oxide was confirmed by X-Ray diffraction and the samples were found to have wurtzite crystal structure with (002) preferred orientation. The films were characterized by Hall-effect, atomic force microscopy, UV-VIS spectroscopy, photoluminescence (PL) and work function measurements. The different studies exhibited an anomalous behavior for the film annealed at 900 °C. The Hall effect, work function measurements and UV-VIS spectroscopy indicated that the resistivity, work function and optical band gap increased as a function of annealing temperature (from 300 °C to 700 °C) however these parameters were found to decrease for the films annealed above 700 °C. The particle size increased with the annealing but for the samples annealed at 900 °C, the shape of the grains changed and became elongated like fibers as observed by the atomic force microscopy. The PL measurements displayed the existence of oxygen vacancies defects for the samples annealed at and above 600 °C. The possible mechanism for this anomaly has been discussed in this work.     

Piezoelectric properties of Bi4Ti3O12 thin films annealed in different atmospheres

Bismuth titanate (Bi₄Ti₃O₁₂—BIT) films were evaluated for use as lead-free piezoelectric thin-films in micro-electromechanical systems. The films were grown by the polymeric precursor method on Pt/Ti/SiO₂/Si (1 0 0) (Pt) bottom electrodes at 700 °C for 2 h in static air and oxygen atmospheres. The domain structure was investigated by piezoresponse force microscopy (PFM). Annealing in static air leads to better ferroelectric properties, higher remanent polarization, lower drive voltages and higher piezoelectric coefficient. On the other hand, oxygen atmosphere favors the imprint phenomenon and reduces the piezoelectric coefficient dramatically. Impedance data, represented by means of Nyquist diagrams, show a dramatic increase in the resistivity for the films annealed in static air atmopshere.     

Thermal stability of amorphous molybdenum trioxide films prepared at different oxygen partial pressures by reactive DC magnetron sputtering

Thin films of MoO₃ were prepared on quartz and Si (1 0 0) substrates by reactive dc magnetron sputtering of a Mo target in an oxygen and argon atmosphere. The structural and optical changes induced in the films due to post-growth annealing have been systematically studied by Rutherford backscattering (RBS), X-ray diffraction (XRD), X-ray reflectivity (XRR) and by optical methods. RBS studies reveal no change in composition of the films upon annealing at high temperatures. Grazing angle XRD studies show that the as-deposited films are amorphous and crystallize to β-MoO₃ phase with small contribution of α-MoO₃ upon annealing at 300 °C. The film prepared at 0.40 Pa transforms to α-MoO₃ upon annealing at 650 °C, while the film deposited at 0.19 Pa still has some β-MoO₃ phase contribution. XRR measurements reveal that the film thickness decreases upon annealing with simultaneous increase of film density. The surface roughness of the films strongly increases after crystallization. The contraction of the film deposited at 0.40 Pa is much greater than the contraction of the film prepared at 0.19 Pa. The mass variation of the film deposited at 0.19 Pa and that deposited at 0.40 Pa are completely different. The optical properties of MoO₃ films deposited at 0.19 and 0.40 Pa are changed strongly by annealing.     

Preparation of homogeneous VOX thin films by ion beam sputtering and annealing process

Polycrystalline VO_x thin films that were prepared for thermal-sensitive material of far infrared sensor had been deposited on Si substrates by ion beam sputtering deposition. Scanning electron microscopy images indicated that VO_x thin films (oxygen pressure of 1.5×10⁻³ Pa) were grown into compact and ultra-fine grains (?50 nm), the film surfaces seemed smooth and uniform. Four-point probe measurements showed that the homogeneity of the films was better than 98% in a size of 30×30 mm². The four-point probe measurement on hot plate presented the sheet resistance and the temperature coefficient of resistance of the VO_x thin film that were 50 kΩ/square and −0.021 K⁻¹ at 28°C, respectively. In addition, some samples annealed in Ar atmosphere had their resistance decreased. Thus, vanadium oxide films containing more amount VO₂ were obtained.     

Deposition and characterization of MgO/Si gate stacks grown by molecular beam epitaxy

In this article, the deposition and characterization of amorphous MgO films grown on Si (001) using molecular beam epitaxy is reported. In order to ensure amorphous films, low substrate temperatures (200 °C) and high oxygen pressures were used (up to 5 × 10^− 3 Pa). Both atomic and molecular oxygen species were used at different pressures. Films ranging in thickness from 3 nm till 30 nm were grown and characterized using structural and electrical methods.The dielectric constant deduced from this thickness series corresponds to 8.74 close to the bulk value of 9.8. The best equivalent oxide thickness value observed for this series - grown under high oxygen pressure - corresponds to 1.2 nm for a current density measured at V_FB − 1 V of 0.1 A/cm². The films grown with atomic oxygen display a lower capacitance and lower leakage compared to the films grown using molecular oxygen. This is due to the appearance of a thin SiO₂ interface layer which is also responsible for the high defect density observed in the capacitance-voltage measurements. Upon annealing both types of films in forming gas for 15 min at 450 °C, the capacitance decreases further while the leakage increases. This change is assigned to the appearance of the lower bandgap (6.6 eV), lower dielectric constant (6.6) phase of silicate, MgSiO₃. Furthermore a V_FB shift of − 0.6 V is observed and is related to the appearance of oxygen vacancies as Mg diffuses into the SiO₂ interface layer.     

Fabrication of epitaxial conductive LaNiO3 films on different substrates by pulsed laser ablation

LaNiO₃ (LNO) thin films were deposited on (1 0 0) MgO, SrTiO₃ (STO) and LaAlO₃ (LAO) crystal substrates by pulsed laser deposition (PLD) under 20 Pa oxygen pressure at different substrate temperatures from 450 to 750 °C. X-ray diffraction (XRD), ex situ reflection high energy electron diffraction (RHEED) and atomic force microscopy (AFM) were employed to characterize the crystal structure of LNO films. LNO films deposited on STO and LAO at a temperature range from 450 to 700 °C exhibit high (0 0 l) orientation. XRD ψ scans and RHEED observations indicate that LNO films could be epitaxially grown on these two substrates with cubic-on-cubic arrangement at a wide temperature range. LNO films deposited at 700 °C on MgO (1 0 0) substrate have the (l l 0) orientation, which was identified to be bicrystalline epitaxial growth. La₂NiO₄ phase appears in LNO films deposited at 750 °C on three substrates. The epitaxial LNO films were tested to be good metallic conductive layers by four-probe method.     

Influence of oxygen pressure on the structural, electrical and optical properties of VO2 thin films deposited on ZnO/glass substrates by pulsed laser deposition

The influence of oxygen pressure on the structural and electrical properties of vanadium oxide thin films deposited on glass substrates by pulsed laser deposition, via a 5-nm thick ZnO buffer, was investigated. For the purposes of comparison, VO₂ thin films were also deposited on c-cut sapphire and glass substrates. During laser ablation of the V metal target, the oxygen pressure was varied between 1.33 and 6.67 Pa at 500 °C, and the interaction and reaction of the VO₂ and the ZnO buffer were studied. X-ray diffraction studies showed that the VO₂ thin film deposited on a c-axis oriented ZnO buffer layer under 1.33 Pa oxygen had (020) preferential orientation. However, VO₂ thin films deposited under 5.33 and 6.67 Pa were randomly oriented and showed (011) peaks. Crystalline orientation controlled VO₂ thin films were prepared without such expensive single crystal substrates as c-cut sapphire. The metal-insulator transition properties of the VO₂/ZnO/glass samples were investigated in terms of electrical conductivity and infrared reflectance with varying temperatures, and the surface composition was investigated by X-ray photoelectron spectroscopy.     

Characteristics of highly orientated BiFeO3 thin films on a LaNiO3-coated Si substrate by RF sputtering

BiFeO₃ (BFO) films were grown on LaNiO₃-coated Si substrate by a RF magnetron sputtering system at temperatures in the range of 300-700 °C. X-ray reflectivity and high-resolution diffraction measurements were employed to characterize the microstructure of these films. For a substrate temperature below 300 °C and at 700 °C only partially crystalline films and completely randomly polycrystalline films were grown, whereas highly (001)-orientated BFO film was obtained for a substrate temperature in the range of 400-600 °C. The crystalline quality of BFO thin films increase as the deposition temperature increase except for the film deposited at 700 °C. The fitted result from X-ray reflectivity curves show that the densities of the BFO films are slightly less than their bulk values. For the BFO films deposited at 300-600 °C, the higher the deposition temperature, the larger the remnant polarization and surface roughness of the films present.     

Influence of incidence angle and distance on the structure of aluminium nitride films prepared by reactive magnetron sputtering

Aluminum nitride (AlN) films were reactively deposited on (100) oriented silicon substrates by reactive radio frequency (RF) magnetron sputtering for different incidence angles and distances between substrate and target.X-ray diffraction (XRD), atomic force microscopy (AFM), and scanning electron microscopy (SEM) were used to consider the influence of process parameters such as reactive gas flow rate, grazing incidence angle (α), and distance (d) between substrate and target surface on the property of AlN films. XRD results showed that AlN film prepared at a constant distance (d) of 3 cm and an incidence angle of 45° revealed a mixture of AlN (002), (100), and (101) planes, while the film prepared at α = 0° revealed a strong AlN (002) orientation which has a perpendicular growth direction to the substrate surface. AFM results showed that AlN film prepared at α = 0° exhibited more flat surface morphology than that of film prepared at α = 45°.     

Structure, hardness and thermal stability of TiAlN and nanolayered TiAlN/CrN multilayer films

TiAlN films were deposited on silicon (1 1 1) substrates from a TiAl target using a reactive DC magnetron sputtering process in Ar+N₂ plasma. Films were prepared at various nitrogen flow rates and TiAl target compositions. Similarly, CrN films were prepared from the reactive sputtering of Cr target. Subsequently, nanolayered TiAlN/CrN multilayer films were deposited at various modulation wavelengths (Λ). X-ray diffraction (XRD), energy dispersive X-ray analysis, nanoindentation and atomic force microscopy were used to characterize the films. The XRD confirmed the formation of superlattice structure at low modulation wavelengths. The maximum hardness of TiAlN/CrN multilayers was 3900 kg/mm², whereas TiAlN and CrN films exhibited maximum hardnesses of 3850 and 1000 kg/mm², respectively. Thermal stability of TiAlN and TiAlN/CrN multilayer films was studied by heating the films in air in the temperature range (T_A) of 500-900 °C for 30 min. The XRD spectra revealed that TiAlN/CrN multilayers were stable up to 800 °C and got oxidized substantially at 900 °C. On the other hand, the TiAlN films were stable up to 700 °C and got completely oxidized at 800 °C. Nanoindentation measurements performed on the films after heat treatment showed that TiAlN retained a hardness of 2200 kg/mm² at T_A=700 °C and TiAlN/CrN multilayers retained hardness as high as 2600 kg/mm² upon annealing at 800° C.     

Influence of oxygen partial pressure on the structural and dielectric properties of Ba(Zr0.3Ti0.7)O3 thin films grown on (LaAlO3)0.3(Sr2AlTaO6)0.35 (001) using pulsed laser deposition

Epitaxial Ba(Zr_0.3Ti_0.7)O₃ thin films were grown on (LaAlO₃)_0.3(Sr₂AlTaO₆)_0.35 (001) single-crystal substrates by pulsed laser deposition at 700 °C in different oxygen partial pressures ranging from 6.7 Pa to 40.0 Pa. A strong correlation is observed between the structure and dielectric properties for the Ba(Zr_0.3Ti_0.7)O₃ thin films. The tetragonal distortion (ratio of in-plane and out-of-plane lattice parameter, a/c) of the films depends on the oxygen partial pressures. a/c varies from 0.989 at 6.7 Pa to 1.010 at 40.0 Pa, indicating the in-plain strain changes from compressive to tensile. The in-plain strain (either compressive or tensile) shifts the Curie temperature of the Ba(Zr_0.3Ti_0.7)O₃ thin films dramatically. Surface morphology and dielectric properties of Ba(Zr_0.3Ti_0.7)O₃ thin films have a strong dependence of the oxygen partial pressure. The film grown 26.7 Pa, which corresponds to a moderate in-plain tensile strain and a Curie temperature of ~ 30 °C, shows the largest relative permittivity, tunability and the best figure of merit in a broad frequency range (1 kHz-500 MHz), which may be a promising candidate for room-temperature microwave device applications.     

Effect of cadmium oxide incorporation on the microstructural and optical properties of pulsed laser deposited nanostructured zinc oxide thin films

CdO doped (doping concentration 0, 1, 3 and 16 wt%) ZnO nanostructured thin films are grown on quartz substrate by pulsed laser deposition and the films are annealed at temperature 500 °C. The structural, morphological and optical properties of the annealed films are systematically studied using grazing incidence X-ray diffraction (GIXRD), energy dispersive X-ray analysis (EDX), scanning electron microscopy (SEM), atomic force microscopy (AFM), Micro-Raman spectra, UV–vis spectroscopy, photoluminescence spectra and open aperture z-scan. 1 wt% CdO doped ZnO films are annealed at different temperatures viz., 300, 400, 500, 600, 700 and 800 °C and the structural and optical properties of these films are also investigated. The XRD patterns suggest a hexagonal wurtzite structure for the films. The crystallite size, lattice constants, stress and lattice strain in the films are calculated. The presence of high-frequency E₂ mode and the longitudinal optical A₁ (LO) modes in the Raman spectra confirms the hexagonal wurtzite structure for the films. The presence of CdO in the doped films is confirmed from the EDX spectrum. SEM and AFM micrographs show that the films are uniform and the crystallites are in the nano-dimension. AFM picture suggests a porous network structure for 3% CdO doped film. The porosity and refractive indices of the films are calculated from the transmittance and reflectance spectra. Optical band gap energy is found to decrease in the CdO doped films as the CdO doping concentration increases. The PL spectra show emissions corresponding to the near band edge (NBE) ultra violet emission and deep level emission in the visible region. The 16CdZnO film shows an intense deep green PL emission. Non-linear optical measurements using the z-scan technique indicate that the saturable absorption (SA) behavior exhibited by undoped ZnO under green light excitation (532 nm) can be changed to reverse saturable absorption (RSA) with CdO doping. From numerical simulations the saturation intensity (I_s) and the effective two-photon absorption coefficient (β) are calculated for the undoped and CdO doped ZnO films.     

Low cost CuInSe2 thin films production by stacked elemental layers process for large area fabrication of solar cell application

Low cost deposition of large area CuInSe₂ (CIS) thin films have been grown on Mo-coated glass substrate by simple and economic stacked elemental layer deposition technique in vacuum. The grown parameters such as concentration of Cu, In and Se elements have been optimized to achieve uniform thin film in vacuum chamber. The as-grown Cu/In/Se stacked layers have been annealed at 200 °C and 350 °C for 1 h in air ambient. The as-grown and annealed films have been further subjected to characterization by X-ray diffraction (XRD), optical absorption, atomic force microscopy (AFM) and I-V measurement techniques. XRD patterns revealed that as-grown Cu/In/Se stacked layers represent amorphous nature while annealed CIS film reproduces nano-polycrystalline nature with chalcopyrite structure. The optical band gap of annealed films increases with respect to air annealing which confirms the reduction of crystallite size. Surface morphology of as-grown Cu/In/Se stacked layers and annealed CIS thin films have been confirmed by AFM images. The electrical measurements show enhancement of conductivity which is useful for solar cell application.     

The effect of annealing on Al-doped ZnO films deposited by RF magnetron sputtering method for transparent electrodes

In this study, transparent conducting Al-doped zinc oxide (AZO) films with a thickness of 150 nm were prepared on Corning glass substrates by the RF magnetron sputtering with using a ZnO:Al (Al₂O₃: 2 wt.%) target at room temperature. This study investigated the effects of the post-annealing temperature and the annealing ambient on the structural, electrical and optical properties of the AZO films. The films were annealed at temperatures ranging from 300 to 500 °C in steps of 100 °C by using rapid thermal annealing equipment in oxygen. The thicknesses of the films were observed by field emission scanning electron microscopy (FE-SEM); their grain size was calculated from the X-ray diffraction (XRD) spectra using the Scherrer equation. XRD measurements showed the AZO films to be crystallized with strong (002) orientation as substrate temperature increases over 300 °C. Their electrical properties were investigated by using the Hall measurement and their transmittance was measured by UV-vis spectrometry. The AZO film annealed at the 500 °C in oxygen showed an electrical resistivity of 2.24 × 10^− 3 Ω cm and a very high transmittance of 93.5% which were decreased about one order and increased about 9.4%, respectively, compared with as-deposited AZO film.     

Hot corrosion behavior of powder metallurgy Rene95 nickel-based superalloy in molten NaCl–Na2SO4 salts

Hot corrosion behavior of powder metallurgy (PM) Rene95 Ni-based superalloy in molten 25%NaCl + 75%Na₂SO₄ salts at 650 °C, 700 °C and 750 °C are investigated by weight loss measurements, X-ray diffraction (XRD), scanning electron microscopy (SEM), and energy dispersive X-ray spectroscopy (EDS). Experimental results show that hot corrosion kinetics follow a square power law at 650 °C and linear power laws at 700 °C and 750 °C. The corrosion layers on the surface of PM Rene95 superalloy are detected to be mainly composed of Cr₂O₃, NiO, and Ni₃S₂ at each temperature. Besides, small amounts of NiCr₂O₄ at 700 °C and NaCl at 750 °C are observed respectively. Cross-sectional morphologies and corresponding elemental maps indicate that corrosion layers near scale/alloy interface are composed of oxides at 650 °C while duplex oxides and sulfides at 700 °C and 750 °C. According to these results, a cooperating mechanism of oxidation and sulfuration for hot corrosion of PM Rene95 Ni-based superalloy is confirmed.     

Optical properties of tungsten oxide thin films by non-reactive sputtering

Tungsten oxide thin films were grown on glass substrates by RF sputtering at room temperature using a tungsten trioxide target for several values of the argon pressure (P_Ar). The structural and morphological properties of these films were studied using X-ray diffraction and atomic force microscopy. The as-deposited films were amorphous irrespective of the argon pressure, and crystallized in a mixture of hexagonal and monoclinic phases after annealing at a temperature of 350 °C in air. Surface-roughness increased by an order of magnitude (from 1 nm to 20 nm) after thermal treatment. The argon pressure, however, had a strong influence on the optical properties of the films. Three different regions are clearly identified: deep blue films for P_Ar ≤ 2.67 Pa with low transmittance values, light blue films for 2.67 Pa < P_Ar < 6 Pa with intermediate transmittance values and transparent films for P_Ar ≥ 6 Pa with high transmittance values. We suggest that the observed changes in optical properties are due to an increasing number of oxygen vacancies as the growth argon pressure decreases.