不同流型下组合约束型提升管出口段固含率分布

在一套组合约束型提升管冷态实验装置上,研究了气力输送和快速流态化两种流型下,出口段局部固含率分布规律及不同操作条件对固含率的影响。结果表明:局部固含率径向分布整体上呈中心小、边壁大的分布特征,并随分布器开孔率和表观气速的降低而增大,随上部流化床层压降和颗粒循环强度的降低而减小;在快速流态化操作下,局部固含率曲线分布形式与常规提升管类似,而在气力输送状态下,临近出口区域局部固含率最大值通常不出现在边壁处,其位置随表观气速和分布器开孔率增加以及颗粒循环强度和上部流化床层压降降低而远离边壁;两种流型下局部固含率径向分布的均匀性均随表观气速及分布器开孔率的增加而升高,随颗粒循环强度及流化床层压降的增加而降低。     

多层流化床床层及溢流管中气固流动特性的模拟

采用多孔介质模型描述两床层间的气体分布板,开发了一种多层流化床典型结构单元的计算流体动力学(CFD)模拟方法,研究了操作气速对多层流化床床层流化状态及其溢流管内颗粒流动特性的影响.结果表明:层间溢流管内颗粒料位具有缓冲作用,使得颗粒进入下床层后被迅速均匀分散,保证了下床层固相均匀性.流化气速增大,下床层进入溢流管的气体...     

分布板开孔率对气固流化床流动特性的影响

在内径0.14 m,高1.6 m的气固流化床中,以空气和流化催化裂化颗粒为气相和固相,采用PV-6A型光纤测速仪和U形管压差计分别测定三种不同开孔率分布板时的颗粒浓度分布和分布板压降,同时应用流体力学软件Fluent 6.2分别对三种不同开孔率分布板压降,径向固含率分布进行了模拟计算,模拟结果与实验值吻合较好.研究结果显示,分布板压降随开孔率的增大而减小,分布板开孔率大于0.86%后对压降影响较小;径向固含率波动随开孔率的增大而增大,开孔率0.46%的分布板径向固含率分布曲线波动最小,气固分布最均匀.     

垂直筛板流化床中FCC催化剂的流化性能

以FCC催化剂颗粒研究垂直筛板流化床内构件对气固两相流化性能的影响,考察了板孔气速、颗粒循环量和帽罩开孔比等筛板结构对流化床压降和提升量强度的影响. 结果表明,气固两相总体逆流流动条件下,帽罩内气速达4 m/s,气固高速并流喷射无气泡,两相接触好、返混小,属快速流态化. 由于没有气泡,床层压力波动小,在塔板上颗粒返混小. 垂直筛板压降随板孔气速、帽罩底隙高度增大而增大,随帽罩开孔比、板孔径增大而减小,颗粒提升量大,床层压降大. 提升量强度随板孔气速、帽罩底隙高度、颗粒循环量增加而增大,随帽罩高度与塔节高度比增大而减少,随帽罩筛孔孔径变化存在最大值. 当帽罩开孔比为1.2~2.5、板孔面积与帽罩截面积比为0.42、帽罩底隙高与板孔孔径比为0.36~0.64时帽罩流化性能较好.     

内构件流化床内颗粒停留时间分布及压降的研究

在一内径100 mm设有数块水平挡板、底部连续加料与上部溢流排料的流化床内,采用粒径为0.04～1.0 mm的精钛矿颗粒,进行了加料速率、流化气速以及内构件间距等不同因素对物料在床内停留时间及压降影响的实验研究,发现在气固并流向上的流化床内增设水平挡板且d/H=1时,可形成稳定流化状态.研究结果表明流化床中的持料量主要取决于流化气速,平均停留时间随流化气速和进料速率增加而降低.平衡时床内颗粒平均粒径大于进料颗粒的平均粒径,使得床内小颗粒停留时间减少,大颗粒停留时间延长,可满足各种粒度颗粒所需的反应时间.通过简化经验公式计算表明,大而重的颗粒趋于沉积床底,小而轻的颗粒趋于漂浮床顶.实验数据可为此类床型用于气固相加工提供有益参考.     

组合约束型提升管出口气固分布器的压降

在一套组合约束型提升管冷态实验装置上,通过实验研究了不同操作条件下提升管出口气固分布器的压降,并与常规气体分布器压降进行了对比。实验结果表明,在零床层及有床层的操作模式下,气固分布器压降均随提升管内表观气速和颗粒循环强度的增加而增大,在颗粒循环强度较低时,气固分布器压降曲线变化的斜率随着表观气速的增加而增大,在颗粒循环强度较高时,气固分布器压降曲线变化的斜率随着表观气速的增加而减小;随着开孔率及上部流化床层压降增加,气固分布器压降呈降低趋势,当流化床层压降达到一定程度后,分布器各孔方可实现有效布气,此后气固分布器压降趋于近似不变;在相同表观气速及开孔率下,气固分布器压降大于常规气体分布器压降。     

组合约束型提升管出口气固分布器的压降

在一套组合约束型提升管冷态实验装置上,通过实验研究了不同操作条件下提升管出口气固分布器的压降,并与常规气体分布器压降进行了对比。实验结果表明,在零床层及有床层的操作模式下,气固分布器压降均随提升管内表观气速和颗粒循环强度的增加而增大,在颗粒循环强度较低时,气固分布器压降曲线变化的斜率随着表观气速的增加而增大,在颗粒循环强度较高时,气固分布器压降曲线变化的斜率随着表观气速的增加而减小;随着开孔率及上部流化床层压降增加,气固分布器压降呈降低趋势,当流化床层压降达到一定程度后,分布器各孔方可实现有效布气,此后气固分布器压降趋于近似不变;在相同表观气速及开孔率下,气固分布器压降大于常规气体分布器压降。     

二元颗粒在气固流化床中的轴向分布特性

通过大型冷模实验测量了二元混合颗粒在流化床内沿轴向的压力分布，考察了混合颗粒截面平均浓度沿轴向的变化特点。通过分析床层压差分布的转折点，确定了密相区与稀相区的相交界面高度，根据实验结果给出了经验关联式。通过压力信号标准差分析了流化床内混合颗粒流化性能与表观气速和颗粒混合比例的关系。实验结果表明，平均颗粒浓度沿流化床轴向呈下降趋势，且在密相区中随表观气速增加而减小，在稀相区中随表观气速增大而增大。二元颗粒中大颗粒比例x_l为0.685时，密相区总平均颗粒浓度存在最大值。密相区与稀相区相交界面高度随表观气速增大而提高。当0.225≤x_l≤0.479和0.561≤u_g≤1.122 m/s时，流化床内二元颗粒的流化性能和混合程度达到最佳。     

气液固三相流化床局部相含率

在以焦末为固相、空气为气相、水为液相的三相流化床中研究了局部气含率和局部固含率径向分布。实验用流化床内径100 mm,高1.7 m,焦末粒度1.07 mm。分别采用电导探针法和光纤法测定局部气含率和局部固含率。结果表明:表观气速为0.35—0.71 cm/s,表观液速为2.12—3.54 cm/s时,局部气含率在流化床中沿径向r/R=0—0.8处分布较均匀,在靠壁面处下降至约0.5%,且随表观液速增加而减小,随表观气速增加而增大,且在距分布板轴向高度分别为370 mm和470 mm时趋势一致,大小沿轴向增加,在表观气速一定时,液速小于2.12 cm/s时,气含率沿径向减小的趋势较明显。局部固含率沿径向分布较均匀,基本不随表观气速变化而变化,随表观液速增大而增大,且在距分布板轴向高度分别为370 mm和470 mm时趋势一致,大小沿轴向减小。     

循环流化床提升管压力瞬时波动的功率谱分析

在φ0.4 m×9.1 m循环流化床提升管中,采集了分布板以上不同轴向高度的压力瞬时波动信号,并采用功率谱进行分析。分析发现,压力瞬时波动功率谱谱图中存在一个振幅最大点,即为主频。增大固体颗粒循环速率或减小提升管操作气速,主频对应振幅增大,而功率谱主频减小。相同操作条件下,随轴向位置的增高,压力瞬时波动的主频基本不变,而主频对应振幅减小。     

The characteristics of particle flow in the overflow and underflow standpipe of fluidized beds

Characteristics of particle flow in the standpipes of a 10 cm I.D.×120 cm high fluidized bed were investigated. The standpipes used in this experiment were vertical overflow and vertical underflow standpipes. Sand particles and polyethylene powders were employed as the bed materials. The effects of standpipe diameter, gas velocity and particle properties on the solid flow rate were determined. The experimental results showed that the flow behaviors of solids through the overflow and underflow standpipes are different with variations of operating conditions. For both standpipes, the mass flow rate of solids was strongly dependent on the standpipe diameter. For the overflow standpipe, the increase of gas velocity increased the solids flow rate. But for the underflow standpipe it decreased the solid flow rate. From the measured pressure drops, solid fractions in the standpipes were determined by the momentum balance. The obtained experimental data of solids mass flow rate were well correlated with the pertinent dimensionless groups for underflow as well as overflow standpipes.     

Entrance effects at a multi-orifice distributor in gas-fluidised beds

The behaviour of multi-orifice distributors in gas-solids fluidised beds has been studied with particular regard to the height of the entrance effect and the mechanics of gas-solids flow in the region immediately above the distributor plate. A model is proposed to predict the height of the entrance effect for a given distributor and gas-solids system at various fluidising flow-rates, and good agreement has been found with experiment. Experiments have been carried out with (a) a two-dimensional air-fluidised bed using three sizes of sand particles (d_p: 137, 263, and 350 μm) and four distributors (orifice diameters: 0.001 m, 0.002 m; orifice spacings: 0.025 m, 0.05 m); and (b) a three-dimensional air-fluidised bed, 0.3 m square in cross-section, using 350 μm sand particles on a distributor with 0.003 m diameter orifices at a spacing of 0.04 m. The principal factors influencing the height of the entrance effect were found to be the incipient fluidising velocity, mean particle size, orifice spacing and gas flow-rate. The model has been used to estimate the minimum ratio of distributor pressure drop to bed pressure drop to bring about an even distribution of gas at the bottom of the bed.     

生物质热裂解双仓式气力输送喂料装置输料特性

设计制造了一套生物质热裂解用双仓式气力输送喂料装置,研究流化气速、喷动气速、有效喷射距离（s=50mm、100mm、150mm、200mm）、输料管内径（d ₁=21mm、24mm、29mm）和生物质颗粒粒径对进料率的影响。试验结果表明,进料率随着流化流速、喷动气速、输料管内径、生物质颗粒粒径的增大而增大。在有效喷射距离为100mm时,进料率最高。固气比随着流化气或喷动气速的增加先增加后降低,在流化气和喷动气的共同作用下,随着气体流速的增加固气比一直在降低。为了描述进料率与喷动气速、流化气速、有效喷射距离、输料管内径以及生物质颗粒粒径之间的关系,采用多元线性回归分析,建立了多元线性回归模型。开展了额外试验验证模型的准确性,结果表明试验值和预测值误差在±10.2%以内,表明所建立的模型可靠,可以利用该模型预测喂料器的进料率。     

Performance characteristics of multijet tuyere distributor plates

A new multijet tuyere type gas distributor is examined for its operational characteristics and appropriateness for gas—solid fluidized bed systems. Tuyeres of different number of slits and slit widths are investigated and their pressure drop data are correlated in terms of tuyere gas velocity. The fluidization quality of silica sand beds of average particle diameter 451 μm is assessed in conjunction with such distributor plates. It is found that such tuyeres service a bed area nearly twice their own size.     

双循环旋风分离器分离性能的实验研究

双循环旋风分离器采用筒锥结构,有2个切向进气口,即主进气口和回流口,分别位于筒体的中部和顶端。排灰口底部设有稳流锥,灰仓侧壁设置了抽气口。通过实验研究了进口位置、进口气速、稳流锥和抽气操作对此新设备分离性能的影响。实验设备直径为0.250 m,实验物料采用粒径0.1—36μm,平均粒径为8.72μm的石英砂。结果表明:主进口进料,风速在12—19 m/s变化时,总分离效率为98.5%—99.17%,可以基本去除大于3μm的颗粒。主进口进料比回流口进料总分离效率大1.5%—3.5%。采用主进气口进料时,稳流锥可以提高总分离效率0.15%—0.2%,抽气操作可以提高总分离效率0.3%—0.4%;回流口进料时,分别提高1.5%—2%和0.6%—1%。     

Slug characteristics of polymer particles in a fluidized bed with different distributors

Pressure fluctuations in a fluidized bed (0.38 m-I.D.x4.4 m-high) of 1.23-mm polymer particles (LLDPE) were measured with different distributors. Slug characteristics (slug frequency and slug rising velocity) were determined by analyzing pressure fluctuations in the bed. The effects of gas velocity (0.6-1.2 m/s) and distributor geometry (opening area ratio, number of orifices and distributor types) on the slug characteristics were determined. The slug frequency decreases slightly with increasing gas velocity. However, slug rising velocity increases linearly with increasing excess fluidization velocity regardless of the distributors used.     

Pressure fluctuation characteristics of polyethylene particles in a gas-solid fluidized bed with different distributors

The effects of gas velocity (0.10–0.68 m/s), distributor geometry (opening area ratio, number of orifices and hole sizes) and the particle size distribution (wide and narrow) of polyethylene on the pressure fluctuation of the distributor and the local pressure drop in the beds have been determined in a gas-solid fluidized bed of 0.07-m I.D. and 0.7 m in height. The mean amplitude and the normalized standard deviation of the local pressure drop were determined by analyzing pressure fluctuation in the bed. The variation of the mean amplitude of the local pressure drop with the gas velocity is independent on the different distributors. The normalized standard deviation of the local pressure drop increased with increasing the ratio of the excess gas velocity to the minimum fluidization velocity and the lumped parameter of the distributor, hD. Also, the normalized standard deviation of the local pressure drop of polyethylene polymerized by Metallocene catalyst (narrow) is higher than that of polyethylene polymerized by Ziegler-Natta catalyst (wide). This paper is dedicated to Professor Dong Sup Doh on the occasion of his retirement from Korea University.     

Attrition of porous glass particles in a fluidised bed

Fluidisation is frequently accompanied by unwanted attrition of the bed material. This paper focuses on the mechanical aspects of fines creation by attrition in fluidised beds supported by multi-orifice distributor plates. The attrition rates of low-density porous glass particles were measured; these particles show abrasive wear behaviour rather than breakage. Positron emission particle tracking (PEPT) was used to follow particle motion in three dimensions within the fluidised bed. For a single orifice distributor with background fluidisation, the attrition rate increased exponentially with increasing orifice gas velocity. For a multi-orifice distributor, however, attrition rates were roughly proportional to excess gas velocity, except near to a critical ratio of particle to orifice diameter; as this ratio approached 2, attrition was observed to increase by an order of magnitude. A method is proposed for estimating attrition rates from a combination of small-scale experimental results and theoretical calculations of distributor jet entrainment rates.     

三维上流式反应器床层流动和返混特性

采用内径为280 mm的上流式反应器,以空气模拟气相、甘油和水混合溶液模拟渣油。用3种不同粒径的氧化铝球形工业催化剂颗粒为填充颗粒,考察了不同模拟物系的颗粒粒径、颗粒密度、液相黏度、不同床层的高径比和不同操作条件对上流式反应器内床层压降及其波动、床层轴向返混的影响规律。得到模拟工业运行物系和操作条件的上流式反应器床层总压降关联式,相对误差在12%以内。床层总压降均随床层高径比、颗粒密度和液相黏度增加而增大,但随颗粒粒径的增大而减小,床层压降波动随表观气速增加而增大。填充颗粒粒径越小、颗粒密度越小、高径比越大,床层内轴向返混越严重;床层内压降和轴向返混均随表观气速的增加而增大。     

高长径比三相内环流反应器中相含率的分布研究

在长径比为22的三相内环流反应器中,常温常压下,以空气-水-石英砂为物系,根据无因次准数建立了气含率、固含率的预测模型,考察了在不同粒径下上升区气含率、下降区气含率和上升区固含率、下降区固含率随表观气速的变化规律和不同固体体积分数下轴向固含率的分布情况。结果表明：不同粒径下上升区和下降区气含率均随表观气速的增大而增大;当粒径（ds）≤0．3mm时,上升区固含率随表观气速的增加呈平缓趋势,下降区固含率随表观气速的增加而增加,当0．3mm〈d。≤1．2mm时,上升区固含率随表观气速的增加而呈先下降后增加的趋势,下降区固含率随表观气速的增加而下降;不同固体体积分数下的固体颗粒的固含率随着轴向高度的增大而变化平缓,能够均匀的分布在反应器中;气含率和固含率的计算值和实验值吻合较好,其平均相对误差分别为6．32％、4．56％。