共查询到19条相似文献,搜索用时 125 毫秒
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
聚氨酯缔合增稠剂(HEUR)是一类高效的缔合型增稠剂,其增稠机理是通过疏水缔合作用形成物理网状交联结构。重点讨论了影响聚氨酯缔合增稠剂增稠效果的因素。其内因方面主要有:亲水主链段、末端疏水基团、疏水基团结构、分子量及分子量分布等;外因方面主要有表面活性剂等。 相似文献
11.
12.
研究了将谷朊粉溶解于水的方法和其在水性建筑涂料中的应用:谷朊粉的耐水性差,不能用作建筑涂料的主要基料,但其具有良好的粘结性、流动性和流平性,可用在合成树脂乳液内墙涂料中,作增稠剂使用,使涂料具有良好的流平性和涂膜外观,而成本与常用的增稠剂相差不大。 相似文献
13.
14.
The work presented in this article involves the study of rheometric profile of several rheological additives in two-component (2K) high build epoxy zinc phosphate primer and two-component high build aliphatic polyurethane topcoat. Viscosity profile and thixotropic behavior at different shear rates have been determined for both the paints using Physica MCR 301 Rheometer of Anton Paar. The valuable information derived from these measurements led to better insight into the influence of these rheological additives on important paint properties like flow and leveling, sag control, in-can settling during storage, etc. Rheometric results were also compared with the results obtained during the actual application of these experimental coatings on mild steel panels. From the rheological study it was concluded that the thickeners based on surface-modified clay and organically modified castor oil derivative work well in epoxy zinc phosphate primer whereas polyurea-based thickener showed better results than other rheological additives in the case of the 2K polyurethane system. Measurement of low shear and high shear viscosity response of different thickeners helps in predicting storage and application behavior of these coatings which correlates well with the actual observation. 相似文献
15.
采用自制的丙烯酸酯微乳液配制了单组分室温交联木器涂料,对成膜助溶剂、润湿流平剂、消泡剂、增稠剂等助剂进行了筛选,并通过正交试验对各助剂的最佳用量进行了确定。结果表明,由丙二醇单丁醚和二丙二醇单丁醚构成的混合成膜助溶剂,其添加量在4%较为适宜;润湿流平剂BYK346的适宜添加量为0.4%;消泡剂FoamStar-A34添加量为0.4%较为适宜;缔合型增稠剂Rheolat 212适宜用量为0.7%。 相似文献
16.
改性胶体及其对高PVC内墙乳胶漆性能的影响 总被引:3,自引:0,他引:3
介绍了改性胶体改善乳胶漆性能的原理,讨论了使用改性胶体配制的高PVC乳胶漆的性能和改性胶体对乳胶漆性能的影响。改性胶体能够降低乳胶漆中分散剂、增稠剂和冻融稳定剂的用量,改善乳胶漆的流平性和涂膜的手感,提高抗分水性能,但对于涂膜的耐洗刷性没有明显的影响。 相似文献
17.
本描述了涂料涂装工艺的重要性,试验讨论了增稠剂、转速、乳胶漆pH值等因素对涂料黏度及流平性的影响,确定了较理想的参数,为乳睃漆的生产及施工提供参考数据,具有一定的实用价值。 相似文献
18.
Al/ZnS涂层织物的红外发射性能 总被引:2,自引:0,他引:2
以片状Al粉为金属颜料,加入ZnS、Na2SiO4、羧甲基纤维素钠和不同粘合剂制备低红外发射率涂料。将涂料涂覆在铝板上,比较含4种不同粘合剂涂层的发射率,研究粘合剂对涂层红外发射率的影响。将涂料涂覆在织物上,测量涂层的表观形态,分析工艺处方、织物种类等因素对织物涂层发射率的影响。油性聚氨酯粘合剂涂层的发射率最低,随着Al和ZnS含量的增加,织物涂层发射率逐渐降低,且不同织物基质上的涂层红外发射率不同。当使用油性聚氨酯为粘合剂,铝粉质量分数为35%~40%,ZnS质量分数为2%时,涤纶织物涂层发射率为0.69。 相似文献
19.
基于互穿网络聚合法合成了丙烯酸酯乳胶涂料乳化剂,选用二烷基磺基琥珀酸盐、聚氧乙烯烷酚基醚、聚二甲基硅氧烷、聚氨酯类增稠剂、乙二醇、2-甲基-4-噻唑啉-3-酮、5-氯-2-甲基-4-异噻唑啉-3-酮等助剂,加入不同的颜料,完成丙烯酸酯乳胶涂料的制备,并分别对其防腐耐霉性、摩擦系数、耐磨性、抗冲击性能进行分析.结果表明:... 相似文献