Effect of Exhaust Gas Recirculation (EGR) on performance,emissions, deposits and durability of a constant speed compression ignition engine

To meet stringent vehicular exhaust emission norms worldwide, several exhaust pre-treatment and post-treatment techniques have been employed in modern engines. Exhaust Gas Recirculation (EGR) is a pre-treatment technique, which is being used widely to reduce and control the oxides of nitrogen (NO_x) emission from diesel engines. EGR controls the NO_x because it lowers oxygen concentration and flame temperature of the working fluid in the combustion chamber. However, the use of EGR leads to a trade-off in terms of soot emissions. Higher soot generated by EGR leads to long-term usage problems inside the engines such as higher carbon deposits, lubricating oil degradation and enhanced engine wear. Present experimental study has been carried out to investigate the effect of EGR on soot deposits, and wear of vital engine parts, especially piston rings, apart from performance and emissions in a two cylinder, air cooled, constant speed direct injection diesel engine, which is typically used in agricultural farm machinery and decentralized captive power generation. Such engines are normally not operated with EGR. The experiments were carried out to experimentally evaluate the performance and emissions for different EGR rates of the engine. Emissions of hydrocarbons (HC), NO_x, carbon monoxide (CO), exhaust gas temperature, and smoke opacity of the exhaust gas etc. were measured. Performance parameters such as thermal efficiency, brake specific fuel consumption (BSFC) were calculated. Reduction in NO_x and exhaust gas temperature were observed but emissions of particulate matter (PM), HC, and CO were found to have increased with usage of EGR. The engine was operated for 96 h in normal running conditions and the deposits on vital engine parts were assessed. The engine was again operated for 96 h with EGR and similar observations were recorded. Higher carbon deposits were observed on the engine parts operating with EGR. Higher wear of piston rings was also observed for engine operated with EGR.     

Experimental investigation of control of NOx emissions in biodiesel-fueled compression ignition engine

Biodiesel is an alternative fuel consisting of the alkyl esters of fatty acids from vegetable oils or animal fats. Vegetable oils are produced from numerous oil seed crops (edible and non-edible), e.g., rapeseed oil, linseed oil, rice bran oil, soybean oil, etc. Research has shown that biodiesel-fueled engines produce less carbon monoxide (CO), unburned hydrocarbon (HC), and particulate emissions compared to mineral diesel fuel but higher NO_x emissions. Exhaust gas recirculation (EGR) is effective to reduce NO_x from diesel engines because it lowers the flame temperature and the oxygen concentration in the combustion chamber. However, EGR results in higher particulate matter (PM) emissions. Thus, the drawback of higher NO_x emissions while using biodiesel may be overcome by employing EGR. The objective of current research work is to investigate the usage of biodiesel and EGR simultaneously in order to reduce the emissions of all regulated pollutants from diesel engines. A two-cylinder, air-cooled, constant speed direct injection diesel engine was used for experiments. HCs, NO_x, CO, and opacity of the exhaust gas were measured to estimate the emissions. Various engine performance parameters such as thermal efficiency, brake specific fuel consumption (BSFC), and brake specific energy consumption (BSEC), etc. were calculated from the acquired data. Application of EGR with biodiesel blends resulted in reductions in NO_x emissions without any significant penalty in PM emissions or BSEC.     

Use of HOT EGR for NOx control in a compression ignition engine fuelled with bio-diesel from Jatropha oil

Environmental degradation and depleting oil reserves are matters of great concern round the globe. Developing countries like India depend heavily on oil import. Diesel being the main transport fuel in India, finding a suitable alternative to diesel is an urgent need. Jatropha based bio-diesel (JBD) is a non-edible, renewable fuel suitable for diesel engines and is receiving increasing attention in India because of its potential to generate large-scale employment and relatively low environmental degradation. Diesel engines running on JBD are found to emit higher oxides of nitrogen, NO_x. HOT EGR, a low cost technique of exhaust gas recirculation, is effectively used in this work to overcome this environmental penalty. Practical problems faced while using a COOLED EGR system are avoided with HOT EGR. Results indicated higher nitric oxide (NO) emissions when a single cylinder diesel engine was fuelled with JBD, without EGR. NO emissions were reduced when the engine was operated under HOT EGR levels of 5–25%. However, EGR level was optimized as 15% based on adequate reduction in NO emissions, minimum possible smoke, CO, HC emissions and reasonable brake thermal efficiency. Smoke emissions of JBD in the higher load region were lower than diesel, irrespective of the EGR levels. However, smoke emission was higher in the lower load region. CO and HC emissions were found to be lower for JBD irrespective of EGR levels. Combustion parameters were found to be comparable for both fuels.     

Hydrogen rich exhaust gas recirculation (H2EGR) for performance improvement and emissions reduction of a compression ignition engine

Hydrogen (H₂), being carbon free energy carrier, is best suitable for compression ignition (CI) engines with better performance and lower carbon derived emissions. Novelty of present study is the employment of low-cost catalyst (alumina) for production of H₂ reformate (hydrogen rich exhaust gas recirculation: H2EGR) in an indigenous catalytic reactor. Experimental tests were carried out on a CI engine under three conditions; base diesel, exhaust gas recirculation (EGR), and H2EGR. Results indicated that brake thermal efficiency of the engine with H2EGR was higher than EGR and comparable with base diesel operation. All carbon-based emissions including smoke emission decreased significantly with H2EGR than diesel and EGR operations. In addition, oxides of nitrogen emission (NO_x) also decreased by about 46% with H2EGR than base diesel operation. It is concluded that H2EGR is a promising option for CI engines for simultaneous reduction of both NO_x and smoke emissions along with the additional benefit of higher efficiency.     

Combustion performance and emission reduction characteristics of automotive DME engine system

This article is a condensed overview of a dimethyl ether (DME) fuel application for a compression ignition diesel engine. In this review article, the spray, atomization, combustion and exhaust emissions characteristics from a DME-fueled engine are described, as well as the fundamental fuel properties including the vapor pressure, kinematic viscosity, cetane number, and the bulk modulus. DME fuel exists as gas phase at atmospheric state and it must be pressurized to supply the liquid DME to fuel injection system. In addition, DME-fueled engine needs the modification of fuel supply and injection system because the low viscosity of DME caused the leakage. Different fuel properties such as low density, viscosity and higher vapor pressure compared to diesel fuel induced the shorter spray tip penetration, wider cone angle, and smaller droplet size than diesel fuel. The ignition of DME fuel in combustion chamber starts in advance compared to diesel or biodiesel fueled compression ignition engine due to higher cetane number than diesel and biodiesel fuels. In addition, DME combustion is soot-free since it has no carbon–carbon bonds, and has lower HC and CO emissions than that of diesel combustion. The NO_x emission from DME-fueled combustion can be reduced by the application of EGR (exhaust gas recirculation). This article also describes various technologies to reduce NO_x emission from DME-fueled engines, such as the multiple injection strategy and premixed combustion. Finally, the development trends of DME-fueled vehicle are described with various experimental results and discussion for fuel properties, spray atomization characteristics, combustion performance, and exhaust emissions characteristics of DME fuel.     

Natural-gas fueled spark-ignition (SI) and compression-ignition (CI) engine performance and emissions

Natural gas is a fossil fuel that has been used and investigated extensively for use in spark-ignition (SI) and compression-ignition (CI) engines. Compared with conventional gasoline engines, SI engines using natural gas can run at higher compression ratios, thus producing higher thermal efficiencies but also increased nitrogen oxide (NO_x) emissions, while producing lower emissions of carbon dioxide (CO₂), unburned hydrocarbons (HC) and carbon monoxide (CO). These engines also produce relatively less power than gasoline-fueled engines because of the convergence of one or more of three factors: a reduction in volumetric efficiency due to natural-gas injection in the intake manifold; the lower stoichiometric fuel/air ratio of natural gas compared to gasoline; and the lower equivalence ratio at which these engines may be run in order to reduce NO_x emissions. High NO_x emissions, especially at high loads, reduce with exhaust gas recirculation (EGR). However, EGR rates above a maximum value result in misfire and erratic engine operation. Hydrogen gas addition increases this EGR threshold significantly. In addition, hydrogen increases the flame speed of the natural gas-hydrogen mixture. Power levels can be increased with supercharging or turbocharging and intercooling. Natural gas is used to power CI engines via the dual-fuel mode, where a high-cetane fuel is injected along with the natural gas in order to provide a source of ignition for the charge. Thermal efficiency levels compared with normal diesel-fueled CI-engine operation are generally maintained with dual-fuel operation, and smoke levels are reduced significantly. At the same time, lower NO_x and CO₂ emissions, as well as higher HC and CO emissions compared with normal CI-engine operation at low and intermediate loads are recorded. These trends are caused by the low charge temperature and increased ignition delay, resulting in low combustion temperatures. Another factor is insufficient penetration and distribution of the pilot fuel in the charge, resulting in a lack of ignition centers. EGR admission at low and intermediate loads increases combustion temperatures, lowering unburned HC and CO emissions. Larger pilot fuel quantities at these load levels and hydrogen gas addition can also help increase combustion efficiency. Power output is lower at certain conditions than diesel-fueled engines, for reasons similar to those affecting power output of SI engines. In both cases the power output can be maintained with direct injection. Overall, natural gas can be used in both engine types; however further refinement and optimization of engines and fuel-injection systems is needed.     

Effect of induction on exhaust gas recirculation and hydrogen gas in compression ignition engine with simarouba oil in dual fuel mode

Biofuels extracted from non-edible oil is sustainable and can be used as an alternative fuel for internal combustion engines. This study presents the performance, emission and combustion characteristic analysis by using simarouba oil (obtained from Simarouba seed) as an alternative fuel along with hydrogen and exhaust gas recirculation (EGR) in a compression ignition (CI) engine operating on dual fuel mode. Simarouba biofuel blend (B20) was prepared on volumetric basis by mixing simarouba oil and diesel in the proportion of 20% and 80% (v/v), respectively. Hydrogen gas was introduced at the flow rate of 2.67 kg/min, and EGR concentration was maintained at 30% of total air introduction. Performance, combustion and emission characteristics analysis were examined with biodiesel (B20), biodiesel with hydrogen substitution and biodiesel, hydrogen with EGR and were compared with neat diesel operation. Results indicate that BTE of the engine operating with biodiesel B20 was decreased when compared to neat diesel operation. However, introducing hydrogen along with B20 blend into the combustion chamber shows a slight increase in the BTE by 1%. NO_x emission was increased to 18.13% with the introduction of hydrogen than that of base fuel (diesel) operation. With the introduction of EGR, there is a significant reduction in NO_x emission due to decrease in in-cylinder temperature by 19.07%. A significant reduction in CO, CO_2, and smoke emissions were also noted with the introduction of both hydrogen and EGR. The ignition delay and combustion duration were increased with the introduction of hydrogen, EGR with biodiesel than neat diesel operation. Hence, the proposed biodiesel B20 with H₂ and EGR combination can be applied as an alternative fuel in CI engines.     

Effect of exhaust gas recirculation (EGR) temperature for various EGR rates on heavy duty DI diesel engine performance and emissions

DI diesel engines are well established today as the main powertrain solution for trucks and other relevant heavy duty vehicles. At the same time emission legislation (mainly for NO_x and particulate matter) becomes stricter, reducing their limit to extremely low values. One efficient method to control NO_x in order to achieve future emissions limits is the use of rather high exhaust gas recirculation (EGR) rates accompanied by increased boost pressure to avoid the negative impact on soot emissions. The method is based on the reduction of gas temperature level and O₂ availability inside the combustion chamber, but unfortunately it has usually an adverse effect on soot emissions and brake specific fuel consumption (bsfc). The use of high EGR rates creates the need for EGR gas cooling in order to minimize its negative impact on soot emissions especially at high engine load were the EGR flow rate and exhaust temperature are high. For this reason in the present paper it is examined, using a multi-zone combustion model, the effect of cooled EGR gas temperature level for various EGR percentages on performance and emissions of a turbocharged DI heavy duty diesel engine operating at full load. Results reveal that the decrease of EGR gas temperature has a positive effect on bsfc, soot (lower values) while it has only a small positive effect on NO. As revealed, the effect of low EGR temperature is stronger at high EGR rates.     

Experimental study of the performances of a modified diesel engine operating in homogeneous charge compression ignition (HCCI) combustion mode versus the original diesel combustion mode

Homogeneous charge compression ignition (HCCI) combustion mode provides very low NO_x and soot emissions; however, it has some challenges associated with hydrocarbon (HC) emissions, fuel consumption, difficult control of start of ignition and bad behaviour to high loads. Cooled exhaust gas recirculation (EGR) is a common way to control in-cylinder NO_x production in diesel and HCCI combustion mode. However EGR has different effects on combustion and emissions, which are difficult to distinguish. This work is intended to characterize an engine that has been modified from the base diesel engine (FL1 906 DEUTZ-DITER) to work in HCCI combustion mode. It shows the experimental results for the modified diesel engine in HCCI combustion mode fueled with commercial diesel fuel compared to the diesel engine mode. An experimental installation, in conjunction with systematic tests to determine the optimum crank angle of fuel injection, has been used to measure the evolution of the cylinder pressure and to get an estimate of the heat release rate from a single-zone numerical model. From these the angle of start of combustion has been obtained. The performances and emissions of HC, CO and the huge reduction of NO_x and smoke emissions of the engine are presented. These results have allowed a deeper analysis of the effects of external EGR on the HCCI operation mode, on some engine design parameters and also on NO_x emission reduction.     

Combustion and emission characteristics of a two-stroke diesel engine operating on alcohol

Though, as a renewable energy resource, alcohol fuel has many advantages in China, it is difficult for diesel engines to operate on alcohol due to its low cetane number and high latent heat of vaporization. This paper proposes an approach to its ignition problem by combining internal exhaust gas recirculation (EGR) with injection of small diesel fuel. Based on this approach, a two-stroke single-cylinder diesel engine was developed. Preliminary studies demonstrated that the engine can run on alcohol with almost zero level of smoke and low exhaust gas temperature, and that the engine operating on alcohol has lower nitrogen oxide (NO_x) emissions and 2–3% higher effective thermal efficiency than that operating on diesel fuel in moderate and high load zones.     

Performance and emission characteristics of CIE using hydrogen,biodiesel, and massive EGR

Hydrogen is considered as an excellent energy carrier and can be used in diesel engines that operate in dual fuel mode. Many studies have shown that biodiesel, which is sustainable, clean, and safe, a good alternative to fossil fuel. However, tests have confirmed that using biodiesel or hydrogen as a fuel or added fuel in compression ignition engines increases NOx concentrations. Cooled or hot exhaust gas recirculation (EGR) effectively controls the NOx outflows of diesel engines. However, this technique is restricted by high particulate matter PM emissions and the low thermal efficiency of diesel engines.In this study, gaseous hydrogen was added to the intake manifold of a diesel engine that uses biodiesel fuel as pilot fuel. The investigation was conducted under heavy-EGR conditions. An EGR system was modified to achieve the highest possible control on the EGR ratio and temperature. Hot EGR was recirculated directly from the engine exhaust to the intake manifold. A heat exchanger was utilized to maintain the temperature of the cooled EGR at 25 °C.The supplied hydrogen increased NOx concentrations in the exhaust gas emissions and high EGR rates reduced the brake thermal efficiency. The reduction in NOx emissions depended on the added hydrogen and the EGR ratios when compared with pure diesel combustion. Adding hydrogen to significant amounts of recycled exhaust gas reduced the CO, PM, and unburned hydrocarbon (HC) emissions significantly. Results showed that using hydrogen and biodiesel increases engine noise, which is reduced by adding high levels of EGR.     

The effect of clove oil and diesel fuel blends on the engine performance and exhaust emissions of a compression-ignition engine

Diesel engines provide the major power source for transportation in the world and contribute to the prosperity of the worldwide economy. However, recent concerns over the environment, increasing fuel prices and the scarcity of fuel supplies have promoted considerable interest in searching for alternatives to petroleum based fuels. Based on this background, the main purpose of this investigation is to evaluate clove stem oil (CSO) as an alternative fuel for diesel engines. To this end, an experimental investigation was performed on a four-stroke, four-cylinder water-cooled direct injection diesel engine to study the performance and emissions of an engine operated using the CSO–diesel blended fuels. The effects of the CSO–diesel blended fuels on the engine brake thermal efficiency, brake specific fuel consumption (BSFC), specific energy consumption (SEC), exhaust gas temperatures and exhaust emissions were investigated. The experimental results reveal that the engine brake thermal efficiency and BSFC of the CSO–diesel blended fuels were higher than the pure diesel fuel while at the same time they exhibited a lower SEC than the latter over the entire engine load range. The variations in exhaust gas temperatures between the tested fuels were significant only at medium speed operating conditions. Furthermore, the HC emissions were lower for the CSO–diesel blended fuels than the pure diesel fuel whereas the NO_x emissions were increased remarkably when the engine was fuelled with the 50% CSO–diesel blended fuel.     

Experimental investigation of the effect of compression ratio and injection pressure in a direct injection diesel engine running on Jatropha methyl ester

Being a fuel of different origin, the standard design parameters of a diesel engine may not be suitable for Jatropha methyl ester (JME). This study targets at finding the effects of the engine design parameters viz. compression ratio (CR) and fuel injection pressure (IP) jointly on the performance with regard to fuel consumption (BSFC), brake thermal efficiency (BTHE) and emissions of CO, CO₂, HC, NO_x and Smoke opacity with JME as fuel. Comparison of performance and emission was done for different values of compression ratio along with injection pressure to find best possible combination for operating engine with JME. It is found that the combined increase of compression ratio and injection pressure increases the BTHE and reduces BSFC while having lower emissions. For small sized direct injection constant speed engines used for agricultural applications (3.5 kW), the optimum combination was found as CR of 18 with IP of 250 bar.     

Effect of manifold injection of hydrogen gas in producer gas and neem biodiesel fueled CRDI dual fuel engine

The high flammability of hydrogen gas gives it a steady flow without throttling in engines while operating. Such engines also include different induction/injection methods. Hydrogen fuels are encouraging fuel for applications of diesel engines in dual fuel mode operation. Engines operating with dual fuel can replace pilot injection of liquid fuel with gaseous fuels, significantly being eco-friendly. Lower particulate matter (PM) and nitrogen oxides (NO_x) emissions are the significant advantages of operating with dual fuel.Consequently, fuels used in the present work are renewable and can generate power for different applications. Hydrogen being gaseous fuel acts as an alternative and shows fascinating use along with diesel to operate the engines with lower emissions. Such engines can also be operated either by injection or induction on compression of gaseous fuels for combustion by initiating with the pilot amount of biodiesel. Present work highlights the experimental investigation conducted on dual fuel mode operation of diesel engine using Neem Oil Methyl Ester (NeOME) and producer gas with enriched hydrogen gas combination. Experiments were performed at four different manifold hydrogen gas injection timings of TDC, 5°aTDC, 10°aTDC and 15°aTDC and three injection durations of 30°CA, 60°CA, and 90°CA. Compared to baseline operation, improvement in engine performance was evaluated in combustion and its emission characteristics. Current experimental investigations revealed that the 10°aTDC hydrogen manifold injection with 60°CA injection duration showed better performance. The BTE of diesel + PG and NeOME + PG operation was found to be 28% and 23%, respectively, and the emissions level were reduced to 25.4%, 14.6%, 54.6%, and 26.8% for CO, HC, smoke, and NO_x, respectively.     

Hydrogen-diesel fuel co-combustion strategies in light duty and heavy duty CI engines

The co-combustion of diesel fuel with H₂ presents a promising route to reduce the adverse effects of diesel engine exhaust pollutants on the environment and human health. This paper presents the results of H₂-diesel co-combustion experiments carried out on two different research facilities, a light duty and a heavy duty diesel engine. For both engines, H₂ was supplied to the engine intake manifold and aspirated with the intake air. H₂ concentrations of up to 20% vol/vol and 8% vol/vol were tested in the light duty and heavy duty engines respectively. Exhaust gas circulation (EGR) was also utilised for some of the tests to control exhaust NO_x emissions.The results showed NO_x emissions increase with increasing H₂ in the case of the light duty engine, however, in contrast, for the heavy duty engine NO_x emissions were stable/reduced slightly with H₂, attributable to lower in-cylinder gas temperatures during diffusion-controlled combustion. CO and particulate emissions were observed to reduce as the intake H₂ was increased. For the light duty, H₂ was observed to auto-ignite intermittently before diesel fuel injection had started, when the intake H₂ concentration was 20% vol/vol. A similar effect was observed in the heavy duty engine at just over 8% H₂ concentration.     

An experimental investigation on hydrogen as a dual fuel for diesel engine system with exhaust gas recirculation technique

With higher rate of depletion of the non-renewable fuels, the quest for an appropriate alternative fuel has gathered great momentum. Though diesel engines are the most trusted power sources in the transportation industry, due to stringent emission norms and rapid depletion of petroleum resources there has been a continuous effort to use alternative fuels. Hydrogen is one of the best alternatives for conventional fuels. Hydrogen has its own benefits and limitations in its use as a conventional fuel in automotive engine system.In the present investigation, hydrogen-enriched air is used as intake charge in a diesel engine adopting exhaust gas recirculation (EGR) technique with hydrogen flow rate at 20 l/min. Experiments are conducted in a single-cylinder, four-stroke, water-cooled, direct-injection diesel engine coupled to an electrical generator. Performance parameters such as specific energy consumption, brake thermal efficiency are determined and emissions such as oxides of nitrogen, hydrocarbon, carbon monoxide, particulate matter, smoke and exhaust gas temperature are measured. Usage of hydrogen in dual fuel mode with EGR technique results in lowered smoke level, particulate and NO_x emissions.     

Comparative performance and emission studies when using olive oil as a fuel supplement in DI and IDI diesel engines

An experimental study is conducted to evaluate and compare the use of a diesel fuel supplement, specifically a 25/75% and a 50/50% blend of waste olive oil and commercial diesel fuel, in a four-stroke, DI (Direct Injection) diesel engine and in a four-stroke, IDI (Indirect Injection) diesel engine having a swirl-combustion chamber. The influence of the blends (diesel fuel+olive oil), for a large range of loads, has been examined on fuel consumption, maximum pressure, exhaust temperature, exhaust smokiness and exhaust-gas emissions such as nitrogen oxides (NO_x), hydrocarbons (HC) and carbon monoxide (CO). The differences in the measured performance and exhaust-emission parameters, from the baseline operation of either engine, are determined and compared. The study shows, for both the DI and IDI engines, a small penalty in specific fuel consumption, a moderate increase in exhaust smokiness and essentially unaltered maximum pressures and exhaust temperatures when using the blends. Also, for both the IDI and DI engines when using the blends, the study shows moderate decreases in emitted nitrogen oxides and increases in hydrocarbons as well as negligible increases in emitted carbon monoxide. Theoretical aspects of diesel engine combustion are used to aid the interpretation of the observed engines' behaviour.     

Application of exhaust gas fuel reforming in diesel and homogeneous charge compression ignition (HCCI) engines fuelled with biofuels

This paper documents the application of exhaust gas fuel reforming of two alternative fuels, biodiesel and bioethanol, in internal combustion engines. The exhaust gas fuel reforming process is a method of on-board production of hydrogen-rich gas by catalytic reaction of fuel and engine exhaust gas. The benefits of exhaust gas fuel reforming have been demonstrated by adding simulated reformed gas to a diesel engine fuelled by a mixture of 50% ultra low sulphur diesel (ULSD) and 50% rapeseed methyl ester (RME) as well as to a homogeneous charge compression ignition (HCCI) engine fuelled by bioethanol. In the case of the biodiesel fuelled engine, a reduction of NO_x emissions was achieved without considerable smoke increase. In the case of the bioethanol fuelled HCCI engine, the engine tolerance to exhaust gas recirculation (EGR) was extended and hence the typically high pressure rise rates of HCCI engines, associated with intense combustion noise, were reduced.     

Gas emissions and particulate matter of non-road diesel engine fueled with F-T diesel with EGR

The gas emissions and particulate matter of non-road diesel engine fueled with Fischer–Tropsch diesel fuel were investigated. The test was carried out on a four-stroke, water-cooled, single-cylinder engine under different the exhaust gas recirculation (EGR) rates such as 0%, 15%, and 30% at 2,700 rpm, 25%, 50%, and 75% load. The test results showed that when the EGR rate is less than 15%, nitrogen oxides (NO_x) are reduced significantly, while hydrocarbon (HC) and carbon monoxide (CO) are increased less than 5%. However, when the EGR rate was 30%, HC and CO were maximally increased to 13.2% and 13.3%, respectively. Additionally, the Field Emission Scanning Electronic Microscope test and Energy Dispersive Spectrometer test were conducted. With increase of EGR rates, the micromorphology of particles was mainly showed as chain-like status and the growth of number concentration of particle was mainly contributed by the nuclear particle when the engine was at 25% load. In contrast, the micromorphology of particles was principally showed as clustered-like status, and the aggregated particles were dominating growth at 50% and 75% load. Moreover, as EGR rates increased, the degree of agglomeration and carbon content were gradually decreased at 25% load. The test also showed the opposite tendency at 50% and 75% load.     

Enhancing the NO2/NOx ratio in compression ignition engines by hydrogen and reformate combustion,for improved aftertreatment performance

Enhanced NO₂ production (without raising total NOx) in a diesel engine combustion chamber can improve the performance of several catalytic aftertreatment systems. Thus this can facilitate a further reduction in key regulated emissions such as nitrogen oxides (NOx) and particulate matter (PM) emissions. The oxidation of NO to NO₂ is an important intermediate step involved in all current aftertreatment systems that are designed for NOx and PM catalytic removal. The performance of both NOx control systems and catalysed particulate filters depend highly on the NO₂ concentration. In this work we have examined the influence of using hydrogen (H₂) and simulated reformate (H₂, CO and EGR gases) as a supplement to diesel fuel on NO₂ production. In actual engine applications a reformer will be integrated within the engine EGR system. This will not only provide the engine with recirculated exhaust gas (i.e. EGR), but will enrich it with H₂ and CO.