基于干涉解调技术的光纤激光器水声传感系统

分析了基于Michelson干涉解调技术的光纤激光器水声传感的原理,在一段掺铒光纤中写入具有π相移的光纤光栅构成光纤激光器,水声压力作用在激光器上引起激光工作波长的变化;采用基于3×3耦合器的偏振无关的非平衡光纤Michelson干涉仪将激光波长变化转化为干涉仪的相位变化;干涉仪的输出由光电探测器转换后使用DSP进行信号解调.针对3×3耦合器分光比不对称的问题,本文提出利用实时调整幅度的2路干涉信号进行解调的方案,该方案不需要3×3耦合器有严格的分光比,消除了外界环境对解调输出的非线性影响.水声探测实验表明,光纤激光器水声传感系统的声压灵敏度为-166.5 dB(参考值1 rad/μPa),解调结果与水声信号具有良好的线性关系.     

Distributed measurement of static strain in an optical fiber with multiple bragg gratings at nominally equal wavelengths

The Fourier transform relationship between the reflected light froma Bragg grating and the complex spatial modulation of the Bragg grating is used to produce a distributed strain sensing system. A tunable external cavity diode laser along with a reference reflector in anoptical fiber are used to produce a measurement of the phase and amplitude of the reflected light from the modulated Bragg grating as a function of wavelength. The system is demonstrated with 22 Bragg gratings in a single fiber on a cantilever beam and compared with foil strain gauge readings.     

Dynamic holographic interferometry by photorefractive crystals for quantitative deformation measurements

A holographic interferometer that uses two-wave mixing in a photorefractive (Bi12SiO20) crystal under an applied ac field is described. The interferometer uses a repetitive sequence of separate record and readout times to obtain quasi real-time holographic interferograms of vibrating objects. It is shown that a good signal-to-noise ratio of the interferometer is obtained by turning off the object illumination and the applied ac field during readout of the hologram. The good signal-to-noise ratio of the resulting holographic interferograms enables phase measurement, which allows for quantitative deformation analysis.     

Dispersive resonators with volume holographic gratings

A dispersive resonator with volume holographic phase gratings for a tunable laser is described. The experimental results showed advantages of these resonators over the analogous devices using blaze-angle reflection relief gratings.     

Ultra-low-power all-optical switching device by use of ytterbium-doped fiber Bragg gratings

A new, to our knowledge, scheme of all-optical switching is put forward by use of an all-fiber Mach-Zehnder interferometer incorporating ytterbium-doped fiber Bragg gratings. The device utilizes the characteristics of the sharp change of group velocity in transmission with the detuning parameter, delta = 2pi n(1/lambda - 1/lambdaB). The switching is achieved by changing the Bragg wavelength of the ytterbium-doped arm of the interferometer. A very small shift of the Bragg wavelength can lead to a pi phase shift between the two arms, so the power needed to realize complete switching is much lower than that of other schemes. In addition, the device can compensate the dispersion of an optical pulse through the positive group velocity dispersion in transmission provided by the gratings.     

Non-hydroscopic vanilla doped dichromated gelatin holographic material

Dichromate gelatins are well-known holographic materials. By doping this material with synthetic vanilla a change in the spectral response from regular dichromate gelatin is observed as an increase in optical density. This mixture presents an unusual high humidity resistance. It was possible to record holographic diffraction gratings using an argon ion laser (λ=488 nm). These gratings exhibit good diffraction efficiency in transmission, on the order of 60% at Bragg angle, with more than 1700 lines/mm spatial resolution. The material development process consists simply of dipping it into using a solution of water and isopropyl alcohol. A hypothesis on the hydroscopic response of this new photosensitive material is also presented.     

Observation of ferroelectric 180° domains by microphotometry of holographic gratings

A new holographic observation technique for 180° domains is demonstrated with a cerium-doped strontium barium niobate sample containing two antiparallel ferroelectric domains. The method relies on the fact that the phase shift of holographically written refractive-index gratings is +π/2 or -π/2 with respect to the initial light interference pattern depending on the orientation of the domains. As a consequence, readout of these gratings creates at the exit face of the sample new interference patterns shifted by 0 or π with respect to the initial one. These patterns, providing an image of the domain structure, are observed by microscope.     

Pump efficiency improvement of a C-band tunable fiber laser using optical circulator and tunable fiber gratings

We propose and demonstrate a tunable fiber laser based on an optical circulator (OC) and two tunable fiber Bragg gratings (TFBGs). The OC acts as a pump power router to improve the pumping efficiency, and a 4% increase in overall conversion efficiency has been observed. The combined tuning spectra range of two TFBGs could cover the entire C-band spectrum from 1530 to 1560 nm. Stable laser output power above 10 dBm is obtained using 1.9 m of erbium-doped fiber and TFBGs with 50% reflectivity. With power equalization by using variable optical attenuators, the power variation is less than 0.1 dB in the whole C band with narrow linewidth of 0.05 nm. A signal-to-noise ratio of 60 dB and a continuous tuning resolution of 0.5 nm have been achieved. The TFBG-based tunable fiber laser can be a promising light source for WDM transmission and fiber sensor applications.     

Improving the holographic sensitivity of dichromated gelatin in the blue-green part of the spectrum by sensitization with xanthene dyes

The holographic properties of dichromated gelatin (DCG) sensitized with various xanthene dyes were studied, and results are reported. The sensitivity of dyed DCG in the green part of the spectrum compared with that of pure DCG (215 mJ/cm(2)) was significantly improved by addition of Rhodamine 6G (140 mJ/cm(2)) or Erythrosin B (90 mJ/cm(2)). Diffraction gratings were recorded with a He-Ne laser at 543.5 nm. The maximum diffraction efficiency was found to be 32% at normal incidence of the readout beam; it was 80% at the Bragg angle.     

Working-point control method for readout of dynamic phase changes in interferometric fiber-optic sensors by tuning the laser frequency

A simple but reliable method, namely the working-point control by tuning the laser frequency, for the dynamic phase shift measurement in a passive homodyne interferometric fiber-optic sensor is proposed. A dc voltage calculated from the photodetector output is applied to the light source to control the interferometer at the condition of maximum sensitivity. Then the signal's phase shift can be obtained from the components of zero and fundamental frequencies. To test the method, an all polarization-maintaining Mach-Zehnder interferometer with a piezoelectric ceramic (PbZrTiO(3), or PZT) cylinder in one arm is constructed. The experimental results show that the simulation signal's phase shift generated by the PZT cylinder can be read out correctly with the method. It has the advantages of simplicities of operation, no-active element in the sensing head, and large operating bandwidth. It can be used for readout of dynamic phase shifts in various interferometric fiber-optic sensors.     

基于光电缆的分布式温度传感网络的实验研究

本文提出增加一根光纤光栅与光电缆绕制在一起,用于监测电缆中的实时温度.采用有限元分析方法,建立了光电缆温度场模型.使用可调谐脉冲激光为光源,在一根光纤上刻制多个相同中心波长的布拉格光栅,即采用全同光栅作为系统的温度传感器,当光电缆线路中温度发生异常时,反射回来的光栅中心波长发生偏移,通过检测反射光中心波长发生的偏移量可...     

采用DBR LD的正弦相位调制激光干涉仪

分析影响正弦相位调制半导体激光干涉仪测量精度和系统分辨力的因素,提出了用分布布拉格反射半导体激光器DBR LD实现高分辨力亚纳米精度测量的方案。理论计算表明,DBR LD的波长连续调制深度比F-P腔LD高一个量级。指出邮于DBR LD的特殊结构可通过简单的反馈回路稳定输出光功率,有效地避免了光强波动对测量精度提高的限制。     

All-optical analog-to-digital conversion scheme based on Sagnac loop and balanced receivers

An all-optical analog-to-digital conversion scheme based on a Sagnac loop and balanced receivers is proposed and experimentally demonstrated. Adjustable phase shift about the transfer function of the Sagnac loop is obtained by using the multiwavelength optical pulses to realize the phase-shift optical quantization. Benefit from the complementary outputs at the transmitted and reflected ports of the Sagnac loop and balanced receiver can be used to obtain the quantized output binary signal for the encoding operation. A proof-of-concept experiment is implemented using a wavelength tunable continuous-wave laser diode. Using 16 different wavelengths, the 16 quantization levels are demonstrated and an effective number of bits (ENOB) of 4?bits is obtained.     

Near-IR absorption in high-purity photothermorefractive glass and holographic optical elements: measurement and application for high-energy lasers

Volume Bragg gratings (VBGs) in photothermorefractive (PTR) glass are widely used for laser beam control including high-power laser systems. Among them, spectral beam combining based on VBGs is one of the most promising. Achieving 100+ kW of combined laser beams requires the development of PTR glass and VBGs with an extremely low absorption coefficient and therefore methods of its measurement. This paper describes the calorimetric method that was developed for measuring a low absorption coefficient in PTR glass and VBGs. It is based on transmission monitoring of the intrinsic Fabry-Perot interferometer produced by the plane-parallel surfaces of the measured optical elements when heated by high-power laser radiation. An absorption coefficient at 1085 nm as low as 5×10(-5) cm(-1) is demonstrated in pristine PTR glass while an absorption coefficient as low as 1×10(-4) cm(-1) is measured in high-efficiency reflecting Bragg gratings with highest purity. The actual level of absorption in PTR glass allows laser beam control at the 10 kW level, while the 100 kW level would require active cooling and/or decreasing the absorption in PTR Bragg gratings to a value similar to that in virgin PTR glass.     

Round Robin for Optical Fiber Bragg Grating Metrology

NIST has administered the first round robin of measurements for optical fiber Bragg gratings. We compared the measurement of center wavelength, bandwidth, isolation, minimum relative transmittance, and relative group delay among several grating types in two industry groups, telecommunications and sensors. We found that the state of fiber Bragg grating metrology needs improvement in most areas. Specifically, when tunable lasers are used a filter is needed to remove broadband emissions from the laser. The linear slope of relative group delay measurements is sensitive to drift and systematic bias in the rf-modulation technique. The center wavelength measurement had a range of about 27 pm in the sensors group and is not adequate to support long-term structural monitoring applications.     

Holographic imaging and interferometry with non-Bragg diffraction orders on volume and surface-relief gratings in lithium niobate and photo-thermoplastic materials

The recording of holographic volume and surface-relief gratings in a photorefractive crystal using a photo-thermoplastic (PTP) holographic camera with an image-bearing signal beam leads to the appearance of two Bragg and two or more non-Bragg diffracted beams that show the transformed images in each beam (rotation and angular amplification of images). Using this real-time mode of interferometry, the hologram is retrieved with a deformed object beam, resulting in the appearance of fringes with a proper phase shift in each of four diffracted beams. This one-shot (one-exposure) phase-shifting interferometry results in clarification of the object wave-front information (for example, from surface deformation) and solution of the sign ambiguity problem. This procedure demonstrates that high-resolution holographic imaging of the PTP holographic camera static deformations in the order of ～0.1?mm can be revealed on the diffusion reflection surface. In addition, it was demonstrated that using the PTP materials could achieve holographic recording and imaging through phase aberration, with the image appearing in the non-Bragg diffraction order.     

Strain and damage monitoring of CFRP in impact loading using a fiber Bragg grating sensor system

A fiber-optic system featuring strain measurement and ultrasonic detection was constructed with fiber Bragg gratings based on wavelength–light intensity conversion technique. This fiber Bragg grating sensing system consists of a broadband light source, a broadband optical filter for strain measurement and a narrowband tunable filter for ultrasonic detection. The system was applied to strain measurement in impact loading to carbon fiber-reinforced plastics and the subsequent impact damage detection. Experimental results demonstrated that fiber Bragg grating sensors could measure strain with higher resolution compared with conventional strain gauges. Furthermore, ultrasonic inspection in which ultrasonic sensitivity was maximized by controlling the transmissive wavelength of the tunable filter could detect a 6.3 × 9 mm² impact damage.     

Phase-stepped gauge block interferometry using a frequency-tunable visible laser diode

Frequency changes induced by bias or temperature modulation of injection diode lasers can provide an economical and effective method of applying phase-stepping interferometry to optical metrology. However, the intrinsic frequency instability of these devices limits their use in gauge block interferometry where precise and repeatable phase steps must be maintained simultaneously on two discontinuous surfaces and over relatively long path lengths. We demonstrate a method using a visible injection diode laser, the frequency of which is locked by using a Fabry-Perot interferometer. Small changes to the length of the Fabry-Perot interferometer shift the frequency of the laser producing proportional and repeatable phase steps to the gauge block interferogram. This method has been successfully implemented with a Fizeau-type gauge block interferometer with a phase measurement resolution of 0.005 lambda. The phase data are then processed to map the surface form of gauge blocks up to 100 mm in length and to objectively assess surface shape parameters.     

一种新型单频激光干涉系统的研究

这种单频激光干涉系统采用共光路设计布局,通过偏振分束器以及1/4波长片等光学器件对干涉条纹进行空间移相,提取相位依次相差90°的三路干涉输出信号,进行比较放大,解决了常规单频激光干涉仪中的光强“零漂”问题。利用共模抑制技术,提高了干涉系统的测量稳定性和重复性。采用光程差放大技术,提高了干涉系统的分辨力。     

Selectivity and tolerance calculations with half-cone-shaped reference beam in volume holographic storage

When developing a compact holographic storage system it is beneficial to use a reflection-type arrangement, where the entire optical system is on the same side of the storage material. For reflection type holographic discs, it is important to use half-cone-shaped spherical reference beams to avoid the ghost images caused by phase conjugate readout. The goal of this paper is to look for appropriate engineering tools to model diffraction efficiency of finite volume holograms created by half-cone-shaped reference beams. Two numerical methods – volume integral and beam propagation – were applied to calculate the shift selectivity curves. Simulation results show significant discrepancies between the shift selectivity curves corresponding to the approximated analytical equation and the numerically calculated shift selectivity curves; there are no Bragg zeros and there are no selective and nonselective directions. Beside the shift selectivity curves, track, focus, tilt and wavelength tolerance values are shown for finite volume holograms.