Dielectric behavior characterization of a fibrous‐ZnO/PVDF nanocomposite

This study is focused on forming a fibrous‐zinc oxide/polyvinylidine fluoride (ZnO/PVDF) nanocomposite and characterizing its dielectric behavior. The nanocomposite is prepared in two steps. First, a network of nanoscale diameter ZnO fibers is produced by sintering electrospun PVA/Zinc Acetate fibers. Second, the ZnO fibrous nonwoven mat is sandwiched between two PVDF thermoplastic polymer films by hot‐press casting. Scanning electron microscope images of the nanocomposite show that hot‐press casting of the fibrous‐ZnO network breaks the network up into short fibers. The in‐plane distribution of the ZnO fillers (i.e., the short fibers) in the PVDF matrix appears to comply with that of the pristine ZnO fibers before hot‐pressing, indicating that the fillers remain well‐dispersed in the polymer matrix. To the authors' knowledge, the work reported herein is the first demonstration of the use of electrospinning to secure the dispersion and distribution of a network of inorganic fillers. Moreover, processing a fibrous‐ZnO/PVDF flexible composite as described in this report would facilitate material handling and enable dielectric property measurement, in contrast to that on a fibrous mat of pure ZnO. Because of the high surface area of the short ZnO fibers and their polycrystalline structure, interfacial polarization is pronounced in the nanocomposite film. The dielectric constant is enhanced significantly‐up to a factor of 10 at low frequencies compared to the dielectric constant of constituent materials (both bulk ZnO and PVDF), and up to a factor of two compared to a bulk‐ZnO/PVDF composite. POLYM. COMPOS., 2010. © 2009 Society of Plastics Engineers     

Effects of epoxy resin‐modified zinc‐ion‐coated nanosilica on structural,thermal and dynamic mechanical properties of propylene‐ethylene copolymer

This paper reports a comparative study of propylene–ethylene copolymer (EP) nanocomposites synthesized using zinc‐ion (Zn²⁺)‐coated nanosilica (ZNS) and the diglycidyl ether of bisphenol‐A (DGEBA, an epoxy resin)‐modified zinc‐ion‐coated nanosilica (EZNS) as nanofillers. These nanocomposites were prepared using the ‘melt mixing’ method at a constant loading level of 2.5 wt%. This loading level is much lower than that used for fillers in conventional composites. The EP nanocomposites were characterized using wide‐angle X‐ray diffractometer (WAXD), a thermo gravimetric analyzer (TGA), a differential scanning calorimeter (DSC), a dynamic mechanical analyzer (DMA) and scanning electron microscopy (SEM). DMA results showed a higher storage modulus for EP‐epoxy‐modified Zn²⁺‐coated nanosilica nanocomposite (EP‐EZNS) with respect to EP and EP‐Zn²⁺‐coated nanosilica nanocomposite (EP‐ZNS). In addition, TGA thermograms showed an increase in degradation temperature of EP in the presence of EZNS. Copyright © 2006 Society of Chemical Industry     

Synthesis,characterization and controlled release properties of zinc–aluminium-beta-naphthoxyacetate nanocomposite

An organic–inorganic nanohybrid nanocomposite was synthesized by co-precipitation method using beta-naphthoxyacetate (BNOA) as guest anion and zinc–aluminium layered double hydroxide (Zn–Al-LDH) as the inorganic host. A well-ordered nanohybrid nanocomposite was formed when the concentration of BNOA was 0.08 M and the molar ratio of Zn to Al, R = 2. Basal spacing of layered double hydroxide containing nitrate ions expanded from 8.9 to 19.5 Å in resulting of Zn–Al-BNOA nanocomposite was obtained indicates that beta-naphthoxyacetate was successfully intercalated into interlayer spaces of layered double hydroxide. It was also found out the BET surface area increased from 1.13 to 42.79 m² g^?1 for Zn–Al-LDH and Zn–Al-BNOA nanocomposite, respectively. The BJH average pore diameter of the synthesized nanocomposite is 199 Å which shows mesoporous-type of material. CHNS analysis shows the Zn–Al-BNOA nanocomposite material contains 36.2 % (w/w) of BNOA calculated based on the percentage of carbon in the sample. Release of BNOA from the lamella of Zn–Al-BNOA was controlled by the zeroth and first order kinetics at the beginning of the deintercalation process up to 200 min and controlled by pseudo-second order kinetics for the whole process. This study suggests that layered double hydroxide can be used as a carrier for organic acid herbicide controlled release formulation of BNOA.     

Synthesis of intercalated lamellar hydroxyapatite/gelatin nanocomposite for bone substitute application

Hydroxyapatite (HAp)/polymer composites have been widely investigated for bone substitute applications in recent years. Inspired by the arrangement of ordered organic and inorganic layers in natural bones and seashells, for the first time a novel intercalated nanocomposite of gelatin and lamellar HAp was prepared via solution intercalation process. X‐ray diffraction (XRD) results showed that the basal spacing of HAp lamellas enlarged by 3.0 nm from 3.1 nm to 6.1 nm, indicating that the gelatin molecules had been intercalated into the gallery of lamellar HAp. The microstructures of pure lamellar HAp and intercalated gelatin/HAp nanocomposite were observed by transmission electron microscopy (TEM) analysis. Fourier transform infrared spectroscopy (FT‐IR) analysis revealed that there were chemical interactions between gelatin molecules and HAp. Thermogravimetric analysis (TGA) results confirmed that thermal stability of the composites was enhanced. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Electrokinetic properties of polypropylene‐layered silicate nanocomposite fibers

Nanocomposite fibers based on polypropylene (PP) polymer were prepared with different content of nanofiller. Filaments were spun from an isotactic iPP homopolymer. Montmorillonite modified by N,N‐dimethyl‐N,N dioctadecylammonium cations was used for preparation of PP nanocomposite fibers. A PP grafted with acrylic acid was added as a coupling agent. Nanocomposite fibers were characterized, i.e., the surface morphology of PP nanocomposite fibers was observed and surface properties were defined by electrokinetic properties determination by zeta potential measurements. For particle distribution observation the plasma etching was involved as a method for sample preparation. The addition of nanoparticles has an impact on ZP value of nanofilled fibers, however, isoelectric point IEP is not significantly influenced by different concentrations of nanofiller. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Development of microbial protective Kolliphor‐based nanocomposite hydrogels

In this scientific work, a novel class of antimicrobial nanocomposite hydrogels were designed and synthesized by chemical and environmentally bioprocess using Kolliphor, acrylamide, and mint leafs in order to achieve antiseptic property for wound applications. In the bioprocess approach, silver nitrate and gold chloride were nucleated with mint leafs in order to obtain effective free individual nano‐inorganic compounds to provide superior antibacterial assets. The formations of dual inorganic nanoparticles were confirmed by transmission electron microscopy, which indicated the size of nanoparticles in the range of approximately 3 ± 2 nm and without agglomeration. The formations of biomaterials were characterized using Fourier transform infrared spectroscopy, thermogravimetric analysis, scanning electron microscopic–energy dispersive spectrometric studies and their swelling properties were determined. Furthermore, the pure hydrogel and the dual inorganic nanocomposite hydrogels developed were tested for antibacterial activities. When compared with the neat hydrogel, the nanocomposite hydrogels significantly improved their anti‐bacterial activities on Bacillus bacterium. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42781.     

Development of Gelatin Based Inorganic Nanocomposite Hydrogels for Inactivation of Bacteria

In this investigation, silver nanocomposite hydrogels were developed by using acrylamide and biodegradable gelatin. Silver nanoparticles were generated throughout the hydrogel networks using in situ method by incorporating Ag⁺ ions and the subsequent treatment with sodium borohydride. The effect of gelatin on the swelling studies was investigated. The hydrogel synthesized silver nanocomposites were characterized by using Fourier transform infrared, UV–Visible spectroscopy, X-ray diffraction, thermogravimetric analysis, scanning electron and transmission electron microscopy techniques. The biodegradable gelatin-based silver nanocomposite hydrogels were tested for antibacterial properties. The results indicate that these biodegradable silver nanocomposite hydrogels can be useful in medical applications, as antibacterial agents.     

UV‐assisted three‐dimensional printing of polymer nanocomposites based on inorganic fillers

In this work, nanocomposites based on a UV‐curable polymeric resin and different inorganic fillers were developed for use in UV‐assisted three‐dimensional (UV‐3D) printing. This technology consists in the additive multilayer deposition of a UV‐curable resin for the fabrication of 3D macro structures and microstructures of arbitrary shapes. A systematic investigation on the effect of filler concentration on the rheological properties of the polymer‐based nanocomposites was performed. In particular, the rheological characterization of these nanocomposites allowed to identify the optimal printability parameters for these systems based on the shear rate of the materials at the extrusion nozzle. In addition, photocalorimetric measurements were used to assess the effect of the presence of the inorganic fillers on the thermodynamics and kinetics of the photocuring process of the resins. By direct deposition of homogeneous solvent‐free nanocomposite dispersions of different fillers in a UV‐curable polymeric resin, the effect of UV‐3D printing direction, fill density, and fill pattern on the mechanical properties of UV‐3D printed specimens was investigated by means of uniaxial tensile tests. Finally, examples of 3D macroarchitectures and microarchitectures, spanning features, and planar transparent structures directly formed upon UV‐3D printing of such nanocomposite dispersions were reproducibly obtained and demonstrated, clearly highlighting the suitability of these nanocomposite formulations for advanced UV‐3D printing applications. POLYM. COMPOS., 38:1662–1670, 2017. © 2015 Society of Plastics Engineers     

Synthesis and properties of PMMA‐ZrO2 organic–inorganic hybrid films

In this work we report the synthesis process and properties of PMMA‐ZrO₂ organic–inorganic hybrid films. The hybrid films were deposited by a modified sol‐gel process using zirconium propoxide (ZP) as the inorganic (zirconia) source, methyl methacrylate (MMA) as the organic source, and 3‐trimetoxy‐silyl‐propyl‐methacrylate (TMSPM) as the coupling agent between organic and inorganic phases. The films were deposited by dip coating on glass slide substrates from a hybrid precursor solution containing the three precursors with molar ratio 1 : 0.25 : 0.25 for ZP, TMSPM, and MMA, respectively. After deposition, the hybrid thin films were heat‐treated at 100°C for 24 h. The macroscopic characteristics of the hybrid films such as high homogeneity and high optical transparence evidenced the formation of a cross‐linked, interpenetrated organic–inorganic network. The deposited PMMA‐ZrO₂ hybrid films were homogeneous, highly transparent and very well adhered to substrates. Fourier Transform Infra‐Red measurements of the hybrid films display absorption bands of chemical groups associated with both PMMA and ZrO₂ phases. The amounts of organic and inorganic phases in the hybrid films were determined from thermogravimetric measurements. The surface morphology and homogeneity of the hybrid films at microscopic level were analyzed by scanning electron microscopy and atomic force microscopy images. From the analysis of optical transmission and reflection spectra, the optical constants (refraction index and extinction coefficient) of the hybrid films were determined, employing a physical model to simulate the hybrid optical layers. The refraction index of the hybrid films at 532 nm was 1.56. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42738.     

复合添加剂对含镁硫酸锌电积锌的影响

通过电沉积锌实验,针对含镁硫酸锌电积液合成出了2种复合添加剂A1(明胶+硫脲+甲酚)和A2(明胶+硫脲+十二烷基磺酸钠). 结果表明,A2对硫酸锌电积锌的沉积效果优于A1,其使低镁(Mg2+<15 g/L)硫酸锌电积锌电流效率提高1%~2%,电能消耗则降低28~78 kW×h/t,A2最佳使用量为15 mg/L. 而对高镁(Mg2+>15 g/L)硫酸锌沉积效果则不理想. 扫描电镜分析表明,A2明显使电锌的表面更致密光滑,减少了支晶和孔洞. 在复合添加剂A2作用下,得到了含镁硫酸锌电积锌的阴极极化曲线,并研究了其作用机理.     

Structure and phase transition in thin films of block copolymer micelles complexed with inorganic precursors

Block copolymer micelle can be used as nano-reactor where separated domains serve as a compartment for the production of nanomaterials, ultimately creating nanocomposite materials. In this work, thin nanocomposite films generated from polystyrene-b-poly(acrylic acid) (PS-b-PAA) micellar solution in which small amount of inorganic precursor was added were investigated. The films were prepared by spin coating onto silicon substrate, and then solvent-annealed. As-spun films exhibit typical micellar structure with spherical shape along which inorganic nanoparticles are dispersed. Such morphology remains unchanged after solvent annealing for micellar films with small amount of inorganic precursor. However, further increase in the amount of inorganic precursors brings about the morphological changes, producing different organization of inorganic nanoparticles in composite films. This behavior was found to strongly depend on the types of precursors and solvents used for annealing. These results illustrate a simple yet useful route to generate the polymeric nanocomposites with diverse structure and composition.     

Preparation of Mineralized Electrospun Fibers as a Biomimetic Nanocomposite

Mineralization of gelatin electrospun nano and micro fiber was investigated in order to prepare a biomimetic bone nanocomposite. For this aim, at first, calcium containing gelatin nanofibers were electrospun by a novel ethanol/water/salt solution. Fibers with mean diameters varying from 300 to 3000 nm were acquired. Then, fiber mats were exposed to phosphate ions by soaking them in phosphate solution or laminating them between phosphate containing gelatin films. SEM micrographs demonstrated the presence of nano to micro sized minerals on gelatin fibers. FTIR and XRD results illustrated that the calcium phosphates in all samples are combinations of brushite and hydroxyapatite.     

Dielectric analysis for in‐situ monitoring of gelatin renaturation and crosslinking

This article probes the use of dielectric analysis (DEA) to monitor the physical changes that occur during gelatin renaturation and crosslinking. An interdigitated dielectric sensor was used to monitor ionic mobility in gelatin. In spite of the large concentration of water and ions in the gelatin model systems, a range of frequencies was found where DEA met all the requirements for ion viscosity measurements necessary to monitor aging gelatin. DEA was successful at detecting gelatin renaturation with a remarkably high signal‐to‐noise ratio. DEA was also capable of detecting crosslinking in the presence of formaldehyde, but only in the special case of fish gelatin. Unlike acid bone gelatin, which is semicrystalline at room temperature, fish gelatin remains fluid. Thus, fish gelatin provides a model system where crosslinking can be monitored in the absence of interference by renaturation processes. The dielectric response was also found to be sensitive to water transport between acid bone gelatin and a simulated pharmaceutical fill made of a PEG 600‐water solution. In the case of acid bone gelatin, the kinetics of renaturation as detected from DEA closely matched those measured by monitoring the evolution of the melting point and of the enthalpy of melting as measured by differential scanning calorimetry (DSC). With dynamic mechanical analysis (DMA), the rise in the loss modulus with renaturation also closely tracked the increase in ionic viscosity. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 2765–2775, 2006     

Synthesis and characterization of novel silver/L‐phenylalanine‐based optically active polyacrylate nanocomposite

Novel bioactive and optically active poly(N‐acryloyl‐L ‐phenylalanine) (PAPA) was synthesized by atom transfer radical polymerization. PAPA‐silver (Ag) nanocomposites have been successfully prepared via in situ reducing Ag⁺ ions anchored in the polymer chain using hydrazine hydrate as reducing agent in an aqueous medium. By controlling of the amount of Ag⁺ ions introduced, we have produced an organic/inorganic nanocomposite containing Ag nanoparticles with well controlled size. Nanocomposites were characterized by X‐ray diffraction (XRD), UV–Vis spectrophotometry, transmission electron microscopy, and Fourier transform infrared. XRD pattern showed presence of Ag nanoparticles. The PAPA/Ag nanocomposites with 1 : 10 silver nitrate (AgNO₃) : PAPA ratio revealed the presence of well‐dispersed Ag nanoparticles in the polymer matrix. All of these Ag nanoparticles formed are spherical and more than 80% of them are in the range of 15–25 nm. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

In Situ Formation of a Novel Nanocomposite Structure Based on MCM-41 and Polyethylene

M41S materials are prepared by in situ assembly of inorganic precursors and organic template and can be viewed as nanocomposites of the siliceous phase and organic surfactant. Calcination of these precursors gives the M41S materials that have been used to prepare novel nanocomposite structures, in which the organic phase inside the nano-sized pores is isolated by the nano-sized inorganic pore walls. The nanocomposite structures can be formed by in situ polymerization of monomers inside the channels. Polymerization of ethylene takes place inside the nano-sized pores, producing the desired nanocomposite structure. The resulting polyethylene was found to be a mixture of crystalline and amorphous phases.     

Self‐assembled polymer nanocomposites and their networks

Synthetic modifications to block‐copolymer structure‐directing agents lead to polymerizable macromers suitable for templating the growth of mesoporous silica particles, which can subsequently react in situ to form extended nanocomposites and nanocomposite networks. Suitably functionalized triblock polymers can preserve the structure‐directing capabilities of the triblock polymer for templating ordered mesoporous silica particle growth and also generate a reactive matrix for subsequent polymer network formation via the reactive end groups. The final self‐assembled products are polymer nanocomposites or novel crosslinked nanocomposite networks whose organic/inorganic composition ratios can vary systematically. The novel self‐assembly route described here should be generally applicable to the synthesis of intimately mixed nanocomposites and nanocomposite networks, starting from a wide variety of block polymeric template/macromer/ordered silica systems. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 41111.     

UVA‐shielding silicone/zinc oxide nanocomposite coating for automobile windows

Among all types of ultraviolet radiation, UVA rays are the most prevalent and can penetrate clouds and glass. In this article, we report the fabrication of a novel silicone/zinc oxide (ZnO) nanocomposite that has outstanding performance in shielding the harmful UVA light. We prepared wurtzite ZnO nanoparticles of three growth durations and dispersed them in a transparent silicone matrix via solution mixing. Our results exhibit a red shift in the absorption peak of the nanocomposites when compared with ZnO colloidal dispersions and decreasing the growth duration of ZnO nanoparticles could improve the UVA‐shielding properties of the nanocomposite. In addition, the nanocomposite presents good shear adhesion strength over 10.5 MPa on glass substrate. The excellent optical and mechanical properties of the novel nanocomposite make it highly promising for automobile window coatings. POLYM. COMPOS., 37:2053–2057, 2016. © 2015 Society of Plastics Engineers     

Preparation of antibacterial temperature‐sensitive silver‐nanocomposite hydrogels from N‐isopropylacrylamide with green tea

This article reports the temperature‐sensitive, green tea (GT)‐based silver‐nanocomposite hydrogels for bacterial growth inactivation. The temperature‐sensitive hydrogels were prepared via free‐radical polymerization using temperature‐sensitive N‐isopropylacrylamide (NIPAM) monomer with GT as the hydrogel matrix. The nanocomposite hydrogels were encapsulated with silver ions via swelling method, which was later reduced to silver nanoparticles using Azadirachta indica leaf extract. The temperature‐sensitive silver nanocomposite hydrogels were analyzed by using Fourier transforms infrared, UV–visible spectroscopy, differential scanning calorimetry–thermogravimetric analysis, X‐ray diffraction, scanning electron microscopy, and transmission electron microscopy. The prepared hydrogels exhibited higher phase volume transition temperature than the NIPAM. The inhibition zone study of the inactivation of bacteria on the developed hydrogels was carried out against Gram negative (Escherichia coli) and Gram positive (Staphylococcus aureus), which revealed that the prepared hydrogels are helpful for the inactivation of these bacteria due to the high stabilization of antibacterial properties of the silver nanoparticles. The developed hydrogels are promising for biomedical applications. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45739.     

富硒、富锌金针菇营养菌丝体的培养

以金针菇F20为菌株,向液体种子培养基、发酵培养基中添加一定量的无机硒和无机锌,利用金针菇对无机离子的富集和转化功能,培养出富含有机硒和有机锌的金针菇营养菌丝体。     

Graphene/poly(styrene‐b‐isoprene‐b‐styrene) nanocomposite optical actuators

This article presents an optomechanical actuator, which is driven by infra red (IR) radiation. The actuator is a nanocomposite‐containing graphene platelets embedded in poly(styrene‐b‐isoprene‐b‐styrene) (SIS) matrix. 0.1 mm thick free‐standing nanocomposite films are fabricated by a simple process of solvent casting. We demonstrate that graphene/SIS nanocomposite contracts on irradiation with IR radiation under strained conditions, whereas expansion behavior was exhibited by them when no prestrain is applied. A maximum photomechanical stress of 28.34 kPa and strain upto 3.1% was obtained for these nanocomposite actuators. We have also studied the mechanical characteristics and thermal degradation of these nanocomposite actuators. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 3902–3908, 2013