合金化和球化工艺对超高碳钢组织和性能的影响

 研究了合金化和球化工艺对超高碳钢组织和性能的影响。用扫描电子显微镜、透射电子显微镜和能谱仪观察了钢的组织形貌和元素分布。结果表明：在碳和铬含量相同的超高碳钢中加入同量的合金元素铝和硅时,铝可明显抑制锻造组织中网状或粗大的颗粒状碳化物的析出、细化珠光体组织和控制石墨形成。UHCS 213Si和UHCS 261Al钢经850 ℃×3 h球化退火处理后,都能得到较好的球化组织,其力学性能分别为：UHCS 213Si钢,Rm=1 033 MPa,Re=734 MPa,A=149%;UHCS 261Al钢,Rm=973 MPa,Re=677 MPa,A=182%。     

Influence of Texture on Mechanical Behavior of Friction-Stir-Processed Magnesium Alloy

Friction stir processing (FSP) improves the mechanical properties of metallic materials. In this study, a magnesium alloy AZ31B was friction stir processed by using single and multiple pass. The friction-stir-processed magnesium alloy exhibits higher tensile strength and ductility in the transverse direction (TD) compared to the longitudinal direction (LD). Both single pass and multiple (two) pass friction-stir-processed material show similar anisotropy in tensile properties, but the multiple pass friction-stir-processed material shows fine-grained microstructure with higher tensile strength and ductility. The tensile anisotropy in the friction-stir-processed AZ31B originated from the textured microstructure that evolved during FSP.     

Laser Welding of Nitinol Thin Foils: Mechanical Properties and Microstructure Depending on Process Parameters

Metallurgical and Materials Transactions A - Ni–Ti alloys are used as functional materials in numerous sectors such as aerospace, automotive engineering, medical technology, and consumer...     

后处理对ZTi60合金材料组织及性能的影响

研究了ZTi60铸造钛合金材料在铸造状态和不同后处理状态下的性能和微观组织。实验结果表明:合金在铸造状态下,存在一定的铸造残余拉应力;经650℃退火处理后,合金的强度和塑性略有提高,硬度HB达到最高,为2 410～2 550 MPa;经热等静压处理后,强度降低,但综合性能有所提高,尤其是冲击吸收功达到最高,为85～94 J;经热等静压+650℃退火后,合金的组织粗化,冲击吸收功显著降低,仅为60～73 J。     

Microstructure Characteristics and Mechanical Properties of Al 413/Mg Joint in Compound Casting Process

Al 413/Mg couples were prepared by the compound casting process. Characterization of the interface by an optical microscope and scanning electron microscope (SEM) showed that a relatively uniform interface composed of three different layers is formed at the interface. The thickness of the interface depended on the melt/insert volume ratio (VR) significantly and was 80?and 470? ??m? in 1.25?and 3?VRs, respectively. The results of the energy dispersive X-ray spectroscopy (EDS), wavelength dispersive X-ray spectroscopy (WDS), and X-ray diffraction analysis showed that the interface layers are mainly composed of Al₃Mg₂, Al₁₂Mg₁₇, and Mg₂Si intermetallic compounds. An accumulation of magnesium oxide films was detected within the (Al₁₂Mg₁₇?+???) eutectic structure of the interface next to the magnesium base metal. Despite different thicknesses of the interface, shear strengths of the Al 413/Mg couples prepared in 1.25?and 3?VRs were almost same. The study of the fracture surfaces of the Al 413/Mg couples revealed that the accumulated magnesium oxide films act as a weak point for initiation of longitudinal cracks and failure of the joint.     

热处理制度对Ti-55531合金组织和力学性能的影响

通过采用不同的热处理制度研究了时效温度和β退火温度对Ti-55531合金显微组织和力学性能的影响。结果表明:Ti-55531合金固溶加时效处理后可获得初生α相呈长条或等轴状的组织,β基体上大量析出的次生α相使其获得较高的强度,且强度随时效温度升高而显著降低,延伸率变化不明显,断面收缩率在620℃以上随着时效温度升高有所增加,但该组织状态断裂韧度偏低;β退火后可获得均匀的片状组织,具有较高的断裂韧性,抗拉强度在600~650℃之间随退火温度升高呈线性关系降低,可根据需要很方便地调整强度级别,塑性随退火温度升高变化不太明显。     

Effect of Process Parameters on Microstructure and Mechanical Properties in Friction Stir Welding of Aluminum Alloy

Friction stir welding process is a promising solid state joining process with the potential to join low melting point materials, particularly aluminum alloys. The most attractive reason for this is the avoidance of solidification defects formed during conventional fusion welding processes. Tool rotational speed and the welding speed play a major role in deciding the weld quality. In the present work an effort has been made to study the effect of the tool rotational speed and welding speed on mechanical and metallurgical properties of friction stir welded joints of aluminum alloy AA6082-T651. The micro hardness profiles obtained on welded zone indicate uniform distribution of grains in the stir zone. The maximum tensile strength obtained is 263 MPa which is about 85% of that of base metal. Scanning electron microscope was used to show the fractured surfaces of tensile tested specimens.     

逆相变退火对连铸坯组织和力学性能的影响

 研究了逆相变退火温度对0.1C5Mn钢连铸坯的组织结构和力学性能的影响规律,采用SEM进行组织结构的表征,利用XRD技术分析连铸坯退火后奥氏体含量,并测试了退火试样的力学拉伸性能。试验结果表明,连铸坯退火过程中发生奥氏体逆转变且在较低退火温度下有少量碳化物析出,随着退火温度升高,奥氏体含量先增加后减少,析出物逐渐溶解消失。提高退火温度可以显著提高试验钢的抗拉强度但却降低它的屈服强度,另外随退火温度升高,断后伸长率和强塑积先增高后降低。在625~650℃退火,可以获得20%~25%的伸长率。研究结果说明利用逆转变退火可以大幅度提高中锰钢铸坯的力学性能。     

轧制工艺参数对高级别管线钢组织及性能的影响

试验研究了在贝氏体基体中形成针状铁素体,来改善高强度管线钢的综合机械性能,特别是低温韧性.为了研究轧制工艺参数对组织的影响,以及获得合适的轧钢条件,以保证强度和韧性的最佳结合,达到X80和X120的性能要求.首先运用Gleeble进行了热模拟,然后,根据热模拟的试验结果,进行了试验轧制.根据组织观察和性能分析,阐述了微观结构和力学性能的关系.结果表明:随着冷却速度的提高,上贝氏体的体积比增加,并且,通过控制冷却速度和终止冷却温度,可以控制各构成相的体积比,从而获得不同的强度级别;由于针状铁素体的有效晶粒尺寸小,贝氏体基体中针状铁素体的含量越多,上架能量(IJSE)越大,并且针状铁素体能降低韧脆转变温度(JDBTF);初轧阶段采用大的压下率对组织细化有很大影响.     

镦粗变形工艺对TC18组织和性能的影响

研究了不同镦粗变形工艺对TC18钛合金棒材的显微组织和力学性能的影响规律。结果表明,TC18钛合金棒材首先在β单相区加热并施加大变形量锻造,而后在（α＋β）两相区加热并以适当变形量锻造,可获得强度、塑性和韧性等综合性能的良好匹配。     

Effects of Heat Treatment Process Parameters on Microstructure and Mechanical Properties of DP440Cold Rolled Strip

In order to optimize the production process, improve the production efficiency and accelerate the development and application of the domestic dual-phase steel, the effects of heat treatment process parameters on microstructure and mechanical properties of DP440 cold rolled strip were studied by the CAS-300 simulated continuous annealing equipment. When the heating rate increased from 5 to 100 ℃/s, both the tensile strength and yield strength increased because of the decreased grain size. When the intercritical annealing temperature increased from 780 to 850 ℃, the martensite content decreased so that the tensile strength decreased first, then increased, and the yield strength increased. When the rapid cooling rate increased from 25 to 100 ℃/s, because the martensite content increased, the tensile strength increased, while the yield strength decreased. When the overaging temperature increased from 260 to 400 ℃, the tensile strength decreased, while the yield strength increased. When the overaging time increased from 240 to 480 s, the tensile strength decreased a little, while the yield strength increased a little.     

预变形对Mg-Gd-Y-Zr合金力学性能的影响

通过拉伸测试、显微硬度测试、扫描电镜分析等手段,研究了预变形对Mg-Gd-Y-Zr合金力学性能的影响。结果表明：时效前的预变形提高了合金峰值硬度,加速了Mg-Gd-Y-Zr合金在220℃下的时效过程,合金峰值时效时间提前2-3 h;另外预变形可以提高合金的强度,同时也降低了合金的塑性;综合考虑合金的强度和塑性,Mg-Gd-Y-Zr合金时效前的预变形以8%为宜。     

锆和钪对Al-Mg铸造合金组织和力学性能的影响

通过金相显微镜、拉伸力学性能测试、XRD等手段研究了在铸造Al-Mg合金中添加不同含量的钪和锆后合金的铸态组织。结果表明,合金添加钪和锆后,明显减小了枝晶网胞尺寸,细化了晶粒。当锆和钪的添加量分别为0.2%、0.4%时,铸造Al-Mg合金组织具有良好的综合性能。     

喷射成形工艺参数及热挤压制度对8009耐热铝合金的组织及性能的影响

采用喷射成形方法制备了A1-8．5Fe-1．4v-1．7Si(8009)耐热铝合金，研究了喷射成形工艺参数及沉积坯件的热挤压工艺对材料的微观组织及性能的影响。结果表明：喷射成形工艺能够有效地抑制8009合金中粗大的富铁相的析出，获得均匀细小的组织；当喷射成形工艺参数选择适当时，沉积坯件具有良好的成形性与致密度，在随后的热挤压过程中，通过较低的挤压比即可使材料达到全致密。合金经过热挤压后，在室温及高温下均具有良好的力学性能。     

稀土元素Sm对Mg-Zn-Y合金组织结构和力学性能的影响

制备了Mg-6Zn-1.5Y-0.8Zr-xSm(x=0,1,2,3)系列合金,研究了稀土元素Sm对Mg-6Zn-1.5Y-0.8Zr合金组织结构和力学性能的影响.通过金相显微镜、扫描电镜、EDS、XRD等观察和分析了合金的微观形貌和组织结构,测量了合金抗拉强度、屈服强度和伸长率等力学性能.结果表明:合金中添加稀土元素Sm后晶粒有了明显的细化,随着Sm元素含量的增加,晶粒细化效果更为明显;通过XRD分析,添加Sm元素后,合金中并没有出现新的含Sm的物相,通过扫描电镜和EDS分析表明,合金中加入的Sm置换了部分Y,形成了Mg3( SmY)2 Zn3,Mg3( SmY) Zn6的相结构,Sm元素对Y的置换主要出现在Mg3( SmY) Zn6结构当中,在Mg3 (SmY) Zn6相结构出现较少;力学性能测试结果表明,随着Sm含量增多,合金晶粒细化,细晶强化作用明显,合金屈服强度逐渐增大,而抗拉强度和伸长率在Sm含量为2％时达到最大,比未添加Sm元素时提高约15％以上.     

镱对铝-镁合金显微组织和力学性能的影响

研究了Yb对Al-Mg合金显微组织和力学性能的影响.结果表明:添加0.3%(质量分数)Yb降低了Al-Mg合金的抗拉强度和屈服强度,主要是由于含Mg和Yb的化合物相的形成降低了Mg和Yb在Al基体中的固溶度,从而减小固溶强化效果.但添加1.0%Yb,基体中Yb溶质原子的浓度提高,产生很强的固溶强化效果,并提高热挤压制品的位错密度和加工硬化程度,改善合金的屈服强度和抗拉强度.     

Influence of Yb:YAG Laser Beam Parameters on Haynes 188 Weld Fusion Zone Microstructure and Mechanical Properties

The weldability of 1.2 mm thick Haynes 188 alloy sheets by a disk Yb:YAG laser welding was examined. Butt joints were made, and the influence of parameters such as power, size, and shape of the spot, welding speed, and gas flow has been investigated. Based on an iconographic correlation approach, optimum process parameters were determined. Depending on the distribution of the power density (circular or annular), acceptable welds were obtained. Powers greater than 1700 W, welding speeds higher than 3.8 m mm^?1, and spot sizes between 160 and 320 μm were needed in the circular (small fiber) configuration. By comparison, the annular (large fiber) configuration required a power as high as 2500 W, and a welding speed less than 3.8 m min^?1. The mechanical properties of the welds depended on their shape and microstructure, which in turn depended on the welding conditions. The content of carbides, the proportion of areas consisting of cellular and dendritic substructures, and the size of these substructures were used to explain the welded joint mechanical properties.