MEMS中多孔硅绝热技术

主要介绍了多孔硅的制备方法(化学法、电化学法及原电池法等)、多孔硅导热系数测试的几种常用手段(温度传感器法、显微拉曼散射法及光声法等)、导热系数的理论模型及影响因素．此外,采用不同方法制备了多孔硅样品,分析了其表面形貌并用显微拉曼光谱法测定了导热系数．结果发现,化学法制备的多孔硅孔径尺寸大于微米量级,而利用大孔硅电化学和原电池法得到的样品孔径尺寸小(约20nm),属于介孔硅．由于腐蚀条件的不同,多孔硅的孔隙率和厚度也不同,多孔硅的导热系数随孔隙率和厚度的增大而迅速减小．     

多孔硅表面氧化钒热敏电阻薄膜的阻温特性

用电化学腐蚀法制备了具有不同导热系数的多孔硅样品(孔隙率为80％±2、厚度为110μm时,导热系数可降低至0．20 W／m·K),并在其表面沉积了氧化钒热敏薄膜,研究了多孔硅样品的热绝缘性能对氧化钒热敏薄膜阻温特性的影响．结果表明:多孔硅良好的热绝缘性使在其表面制备的氧化钒热敏薄膜电阻的灵敏度远高于在硅基底上制备的热敏电阻的(多孔硅和硅片上的氧化钒薄膜电阻随功率变化斜率分别为120 kΩ／μW和2．1 kΩ／μW),且热敏电阻的灵敏度随着多孔硅孔隙率和厚度的增大而升高．     

纳米多孔硅的电化学制备及性能研究

纳米多孔硅是一种潜在的化学和生物传感材料,本文采用电化学腐蚀法制备纳米多孔硅。采用SEM技术分析多孔硅的表面形貌,研究了腐蚀条件对多孔硅的孔隙率、厚度、I-V特性的影响。结果表明,多孔硅的孔隙率随着腐蚀电流密度和腐蚀时间的增加而呈线性增大趋势;其厚度随着腐蚀电流密度的增加而近似呈线性增大趋势,随腐蚀时间的成倍增加而显著增大;其I-V特性表现出非整流的欧姆接触。     

适用于微型燃料电池扩散层的多孔硅的可控制备工艺研究

多孔硅以其多孔结构及大的表面体积比等特点被认为是可在基于MEMS技术的微型燃料电池中代替碳 纸、碳布作为扩散层的材料. 本文考虑传统碳纸、碳布作为扩散层的要求, 并结合多孔硅材料的特点, 选用n<100>(0.04～0.15 Ω·cm)单晶硅进行了多孔硅制备工艺的研究; 考察了腐蚀液的浓度、电流密度和氧化处理时间对多孔硅的孔隙率、孔深度及氧化速率 的影响, 实现了多孔硅的可控制备. 孔隙率为40%、孔径为350～700nm、厚度为60μm的多孔硅膜电极经循环伏安测定, 在0.5mol/L H₂SO₄溶液中, 表现出与碳纸相近的电活性, 显示了潜在的应用价值.     

基于热绝缘的多孔硅技术及其在微传感器中的应用

介绍了多孔硅的热导率特性以及孔径、孔隙率、热处理等因素对其影响.分析了目前基于热绝缘的多孔硅制备技术发展现状,着重对阶梯电流法和脉冲电流法进行了介绍和比较, 认为脉冲电流法因为其特殊的优势,将在以后的发展中得到更广泛的应用.多孔硅由于其热绝缘特性以及技术优势,已经在微传感器领域得到广泛的应用.     

多孔硅基热敏薄膜的制备与性能

对MEMS用具有绝热性能的多孔硅基底上沉积的热敏感薄膜进行了研究．首先用电化学方法制备多孔硅,分别在多孔硅基底和硅基底上通过溅射镀膜方法沉积氧化钒、Cu、Au热敏薄膜,测试多孔硅基底和硅基底上的氧化钒及金属薄膜电阻的热敏特性．结果表明,在多孔硅基底表面沉积的热敏薄膜具有与硅基表面热敏薄膜同样的热敏特性且表现出更高的灵敏度;此外,对沉积在不同制备条件得到的多孔硅上的氧化钒薄膜电阻热敏特性进行比较,发现随着孔隙率和厚度的增加,多孔硅的绝热性能提高,其上沉积的氧化钒薄膜电阻热敏特性增强．     

用于MEMS热敏传感器中绝热层的多孔硅性能研究

利用电化学方法制备了多孔硅,利用显微拉曼光谱法测量多孔硅样品的热导率和多孔硅中的残余应力,利用纳米压入测量仪测量多孔硅显微硬度与弹性模量.研究了多孔硅绝热性能和力学性能与微观结构的关系,认为通过控制制备条件可以得到绝热性能和力学性能满足MEMS热敏传感器结构性能要求的多孔硅.     

应用于微电子机械系统中多孔硅的研究

针对多孔硅在MEMS中作为牺牲层和绝热层的应用,主要研究了电化学腐蚀法制备多孔硅的实验条件与多孔硅深度及其孔隙率间的关系,实验发现电化学腐蚀法制备多孔硅的腐蚀速率在腐蚀前期阶段基本是一定值(电流密度为80mA/cm2时为1.3μm/min,电流密度为40 mA/cm2时为0.4μm/min),但到腐蚀后期阶段随着孔深的增加有所下降.同时发现对于不同的腐蚀电流密度,多孔硅的孔隙率都有随腐蚀时间的延长先增加后降低的趋势,用Beale模型可以很好的解释这一现象.最后,针对多孔硅在制备后易发生龟裂的现象,用拉曼光谱分析了多孔硅的内部应力情况,结果表明随多孔硅孔隙率的上升其内部残余应力有增加的趋势.     

纳米多孔硅膜在医学上的应用

采用纳米技术和生物微电子机械系统技术制备纳米多孔硅膜,可准确控制膜的厚度、几何形状、孔大小、孔分布和孔隙率。纳米多孔硅膜具有优异的耐热性和化学稳定性,且可回收利用。在医学上的纳米多孔硅膜可作为药物载体、免疫隔离生物胶囊、纳米硅微镜和纳米多孔硅生物传感器。     

图案化厚膜多孔硅制备与表征

图案化多孔硅是微电子、微机械、光电子器件的重要组成部分.实验以含Si3N4保护层的光刻单晶硅片为基底,采用电化学阳极氧化法制备图案化厚膜多孔硅,分析阳极氧化前后Si3N4保护层表面形貌变化特征和光刻尺寸对图案化多孔硅宽度、膜层厚度的影响规律,表征图案化多孔硅的结构、组成与发光性能.结果表明,氧化前Si3N4保护层局部区域出现枝晶,阳极氧化后形成不均匀孔状结构;制备的图案化多孔硅膜厚62～83μm,其横向扩展程度和膜层厚度均随光刻尺寸增大呈减小趋势;图案化多孔硅微结构含大量不规则裂纹和硅柱,新鲜制备的表面含Si-Hx键,其光致发光峰值波长650nm.     

Insertion of triangulated surfaces into a meccano tetrahedral discretization by means of mesh refinement and optimization procedures

In this paper, we present a new method for inserting several triangulated surfaces into an existing tetrahedral mesh generated by the meccano method. The result is a conformal mesh where each inserted surface is approximated by a set of faces of the final tetrahedral mesh. First, the tetrahedral mesh is refined around the inserted surfaces to capture their geometric features. Second, each immersed surface is approximated by a set of faces from the tetrahedral mesh. Third, following a novel approach, the nodes of the approximated surfaces are mapped to the corresponding immersed surface. Fourth, we untangle and smooth the mesh by optimizing a regularized shape distortion measure for tetrahedral elements in which we move all the nodes of the mesh, restricting the movement of the edge and surface nodes along the corresponding entity they belong to. The refining process allows approximating the immersed surface for any initial meccano tetrahedral mesh. Moreover, the proposed projection method avoids computational expensive geometric projections. Finally, the applied simultaneous untangling and smoothing process delivers a high‐quality mesh and ensures that the immersed surfaces are interpolated. Several examples are presented to assess the properties of the proposed method.     

Certification Institutions Expected to Update and Transfer Information on Present Standards

Standards are the basis for production enterprises to organize production, ex-factory inspection, trade (delivery) and technical exchanges, product certification, quality arbitration and supervision.……     

Flow calorimeter for enthalpy increment measurements on condensed gases

A flow calorimeter for enthalpy increment measurements on condensed gases is presented. A better knowledge of the properties of the liquefied natural gas is needed, and therefore a liquid loop has been designed for our flow calorimeter. The fluid loop in the calorimeter is designed in order to avoid the two-phase region, since two phases would give compositional disturbances in the measurements. The avoidance of the two-phase region is made possible by increasing the pressure of the test fluid after the measurement section, then heating the fluid at super-critical pressure past the critical point. Finally, the fluid is throttled to the low-pressure gas state at the inlet condition of the compressor that circulates the fluid. To perform the pressure increase, a new cryogenic pump has been designed. To evaluate the new equipment, measurements were taken on liquid ethane over the temperature range 146–256 K at pressure between 0.9 and 5.1 MPa.     

Refrigerators Enter a New Era of Health Preservation Frestech initiates the establishment of China's first standard for household sterilization refrigerators

On November 30, 2007, the China Association for Standardization (CAS) held a press conference at Beijing Diaoyutai State Guest House. Leaders from the China Household Electric Appliance Research Institute, the China Household Electric Appliance Association, and the China Consumers' Association attended and made speeches.……     

Optimum-Simulation von Ernteprozessen

Zusammenfassung Bei der Gestaltung von Ernteprozessen — beispielsweise des Prozesses Mähdrusch, Körnertransport und -abnahme — als transportverbundene Fließarbeitsverfahren mit mindestens zwei verschiedenen Arbeitsmitteln gibt es einen großen Optimierungsspielraum. Solche Prozesse sind mehrstufige Bedienungsprozesse mit gemischter Anordnung der Bedienungseinrichtungen. Außerdem besitzen sie stark ausgeprägte räumliche Aspekte. Es wird vor allem gezeigt, welche Merkmale solcher Prozesse in Simulationsmodellen abgebildet sein müssen, welche Zielgrößen in Abhängigkeit von welchen Einflußgrößen unter Berücksichtigung welcher Prozeßbedingungen ermittelt werden sollten und wie der Bewertungsprozeß zur Ermittlung der gewünschten Informationen gestaltet werden muß.     

A study of centrifugal cast high boron high speed steel

In the present study a high‐boron high speed steel (HSS) roll material was designed. Many expensive alloy elements have been substituted by cheap boron alloy, and high‐boron high speed steel roll has been manufactured by centrifugal casting method. The microstructures, mechanical properties and wear resistance of centrifugal casting high‐boron high speed steel roll have been investigated by optical microscopy (OM), scanning electron microscopy (SEM), and X‐ray diffraction (XRD) analysis, hardness test, impact test and wear test. The results indicated that the solidification microstructures of high‐boron high speed steel roll consisted of M₂(B,C), (W,Mo)₂(B,C), M₃(B,C), M₂₃(B,C)₆ type borocarbides and martensite, a small amount of retained austenite. Borocarbides were continuously distributed over the grain boundary. After quenching from 1050 °C, local broken network appeared in partial borocarbides, and fine secondary borocarbide precipitated from the matrix. After tempering from 525 °C, the amount of precipitated borocarbide increased significantly. After heat treatment, the hardness of high‐boron high speed steel roll excelled 60 HRC, and its impact toughness excelled 8.0 J/cm². The single groove steel rolling amount of high‐boron high speed steel rolls increases by 500% than that of bainite cast iron roll, when the rolls are used in K₁ mill housing of bar mill.     

Thixotropy of Systems with Shear Thinning and Plastic Flow Behavior

The definition of the thixotropy is a decrease in viscosity with time in shear and a subsequent recovery of viscosity after the shear deformation is removed.We ...     

Brainstorming for ISO Strategy 2016-2020

正Responding to ISO’s appeal for survey for the to-be-developed ISO Strategy Plan for 2016-2020,SAC hosted a special workshop over the needs and comments of various fi elds on June 8 in Beijing.The workshop was attended by ISO President-elect and Ansteel General Manager Zhang Xiaogang,SAC Vice-Administrator Yu Xinli,and 30 experts from     

CNAS Passes APLAC's PTP Review

正The review group of Asia Pacific Laboratory Accreditation Cooperation(APLAC)carried out a 4-day peer review of the proficiency testing provider(PTP)for China National Accreditation Service for Conformity Assessment(CNAS)from July 28 to 31,2014.CNAS passed the PTP review with excellent performance.Two senior peer reviewers of APLAC made a comprehensive,rigorous and detailed review of CNAS’s PTP accreditation activities,and made the on-spot inspection of the review groups in Shanghai and Shenzhen respectively.