Greenhouse gas emissions and energy balance of palm oil biofuel

The search for alternatives to fossil fuels is boosting interest in biodiesel production. Among the crops used to produce biodiesel, palm trees stand out due to their high productivity and positive energy balance. This work assesses life cycle emissions and the energy balance of biodiesel production from palm oil in Brazil. The results are compared through a meta-analysis to previous published studies: Wood and Corley (1991) [Wood BJ, Corley RH. The energy balance of oil palm cultivation. In: PORIM intl. palm oil conference – agriculture; 1991.], Malaysia; Yusoff and Hansen (2005) [Yusoff S, Hansen SB. Feasibility study of performing an life cycle assessment on crude palm oil production in Malaysia. International Journal of Life Cycle Assessment 2007;12:50–8], Malaysia; Angarita et al. (2009) [Angarita EE, Lora EE, Costa RE, Torres EA. The energy balance in the palm oil-derived methyl ester (PME) life cycle for the cases in Brazil and Colombia. Renewable Energy 2009;34:2905–13], Colombia; Pleanjai and Gheewala (2009) [Pleanjai S, Gheewala SH. Full chain energy analysis of biodiesel production from palm oil in Thailand. Applied Energy 2009;86:S209–14], Thailand; and Yee et al. (2009) [Yee KF, Tan KT, Abdullah AZ, Lee KT. Life cycle assessment of palm biodiesel: revealing facts and benefits for sustainability. Applied Energy 2009;86:S189–96], Malaysia. In our study, data for the agricultural phase, transport, and energy content of the products and co-products were obtained from previous assessments done in Brazil. The energy intensities and greenhouse gas emission factors were obtained from the Simapro 7.1.8. software and other authors. These factors were applied to the inputs and outputs listed in the selected studies to render them comparable. The energy balance for our study was 1:5.37. In comparison the range for the other studies is between 1:3.40 and 1:7.78. Life cycle emissions determined in our assessment resulted in 1437 kg CO₂e/ha, while our analysis based on the information provided by other authors resulted in 2406 kg CO₂e/ha, on average. The Angarita et al. (2009) [Angarita EE, Lora EE, Costa RE, Torres EA. The energy balance in the palm oil-derived methyl ester (PME) life cycle for the cases in Brazil and Colombia. Renewable Energy 2009;34:2905–13] study does not report emissions. When compared to diesel on a energy basis, avoided emissions due to the use of biodiesel account for 80 g CO₂e/MJ. Thus, avoided life cycle emissions associated with the use of biodiesel yield a net reduction of greenhouse gas emissions. We also assessed the carbon balance between a palm tree plantation, including displaced emissions from diesel, and a natural ecosystem. Considering the carbon balance outcome plus life cycle emissions the payback time for a tropical forest is 39 years. The result published by Gibbs et al. (2008) [Gibbs HK, Johnston M, Foley JA, Holloway T, Monfreda C, Ramankutty N, et al., Carbon payback times for crop-based biofuel expansion in the tropics: the effects of changing yield and technology. Environmental Research Letters 2008;3:10], which ignores life cycle emissions, determined a payback range for biodiesel production between 30 and 120 years.     

Biofuel production potentials in Europe: Sustainable use of cultivated land and pastures. Part I: Land productivity potentials

IIASA's agro-ecological zones modelling framework has been extended for biofuel productivity assessments distinguishing five main groups of feedstocks covering a wide range of agronomic conditions and energy production pathways, namely: woody lignocellulosic plants, herbaceous lignocellulosic plants, oil crops, starch crops and sugar crops. A uniform Pan-European land resources database was compiled at the spatial resolution of 1 km². Suitability and productivity assessments were carried out by matching climate characteristics with plant requirements, calculating annual biomass increments or yields including consideration of soil and terrain characteristics of each grid-cell.Potential biomass productivity and associated energy yields were calculated for each grid-cell. Spatial distributions of suitabilities of biofuel feedstocks in Europe were generated for each individual feedstock as well as for the five biofuel feedstock groups. Estimated agronomical attainable yields, both in terms of biomass (kg ha^?1) as well as biofuel energy equivalent (GJ ha^?1), were mapped and tabulated by agriculture and pasture land cover classes as derived from the CORINE land cover database. Results have been further aggregated by administrative units at NUTS 2 level.     

The feasibility and implications for conventional liquid fossil fuel of the Indonesian biofuel target in 2025

This paper identifies conventional liquid fossil fuels that can be replaced or blended with biofuel and quantifies the biofuels required to meet the Indonesian biofuel target of at least 5% of the total primary energy mix in 2025. The analysis was conducted using the Long range Energy Alternatives Planning (LEAP) system with an energy elasticity of 1 and maximum allowable biofuel blending ratios according to the current best practices. The results show that the target could be achieved with the maximum blending alternative based on constant energy demand growth of 6%. The target requires a total contribution from biofuel of about 8–27 GL in 2025 depending on blending ratios. In energy terms, these are equivalent to 232–782 PJ or about 40–135 million barrels crude oil, which constitute roughly around 3.3–11.0% of the estimated liquid fossil fuel oil annual consumption in that year. The results imply that it may have detrimental environmental impact, as it requires 5.2 million ha of palm oil and sugar cane plantations. On the positive side, achieving the target offers potential new employment opportunities of about 3.4 million jobs, particularly in the agricultural sector relevant to liquid biofuel production.     

Investigating the potential for energy,fuel, materials and chemicals production from corn residues (cobs and stalks) by non-catalytic and catalytic pyrolysis in two reactor configurations

The results of thermogravimetric analysis (TGA), non-catalytic and catalytic pyrolysis of corn cobs and corn stalks are reported in this paper. Pyrolysis took place in two different reactor configurations for both feedstocks: (1) fast pyrolysis in a captive sample reactor; and (2) non-catalytic slow pyrolysis and catalytic pyrolysis in a fixed-bed reactor. Experiments were carried out in atmospheric pressure at three temperatures: low temperature (360–380 °C), medium temperature (500–600 °C) and at high temperature (600–700 °C). The results of the experimental study were compared with data reported in the literature. Investigating the potential of corn residues for energy, fuel, materials and chemicals production according to their thermochemical treatment products yields and quality, it can be stated that: (a) corn stalks could be suitable raw material for energy production via gasification at high temperature, due to their medium low heating value (LHV) of pyrolysis gas (13–15 MJ/m³); (b) corn cob could be a good solid biofuel, due to the high LHV (24–26 MJ/kg) of the produced char; (c) additionally, corn cobs could be a good material for activated carbon production after being activated or gasified with steam, due to its high fixed carbon content(～74 wt%); (d) liquid was the major pyrolysis product from catalytic pyrolysis (about 40–44 wt% on biomass) for both feedstocks; further analysis of the organic phase of the liquid products were hydrocarbons and phenols, which make them interesting for chemicals production.     

Utilization of carbon-negative biofuels from low-input high-diversity grassland biomass for energy in China

This paper analyzes utilization of carbon-negative biofuels from low-input high-diversity grassland biomass on degraded lands (LIHD) for energy including energy equivalent to green house gases (GHG) capture and storage. The results show that the energy output of LIHD biomass on degraded soil is nearly equal to that of ethanol from conventional corn grain on fertile soil. It has also been shown that LIHD biofuel is far more economical than the conventional biofuels such as corn ethanol or soybean biodiesel.China is a large agriculturally developing country, with its rural area largely populated and vast land degraded. It is in this respect that we analyzed the utilization of LIHD. The potential of using energy from LIHD biomass on degraded lands in China is estimated. The results show that the potential energy production of LIHD biomass reaches 6350971.32 TJ year^?1, accounting for about 15% of China’s energy consumption in 2002.     

The potential biomass for energy production in the Czech Republic

Biomass production is a promising alternative for the Czech Republic's (CZ) agricultural sector. Biomass could cover the domestic bio-energy demand of 250 PJ a⁻¹ (predicted for 2030), and could be exported as bio-fuels to other EU countries. This study assesses the CZ's biomass production potential on a regional level and provides cost–supply curves for biomass from energy crops and agricultural and forestry residues. Agricultural productivity and the amount of land available for energy crop production are key variables in determining biomass potentials. Six scenarios for 2030 with different crop-yield levels, feed conversion efficiencies and land allocation procedures were built. The demand for food and fodder production was derived from FAO predictions for 2030. Biomass potential in the CZ is mainly determined by the development of food and fodder crop yields because the amount of land available for energy crop production increases with increasing productivity of food and fodder crops. In most scenarios the NUTS-3 regions CZ020, 31 and 32 provided the most land for energy-crop production and the highest biomass potentials. About 110 PJ a⁻¹, mostly from agricultural and forestry residues, can be provided from biomass when the present Czech agricultural productivity is maintained. About 195 PJ a⁻¹ (105 PJ from energy crops) can be provided when production systems are optimised with regard to fertilizer regimes and 365 PJ a⁻¹ (290 PJ from energy crops) when the yield level of Dutch agriculture is reached. Costs for woody biomass decrease with increasing plantation yield and range between 2.58 and 4.76 € GJ⁻¹. It was concluded that Czech agriculture could provide enough biomass for domestic demand and for export if agricultural productivity is increased.     

Life cycle assessment of a Brassica carinata bioenergy cropping system in southern Europe

The energetic and environmental performance of production and distribution of the Brassica carinata biomass crop in Soria (Spain) is analysed using life cycle assessment (LCA) methodology in order to demonstrate the major potential that the crop has in southern Europe as a lignocellulosic fuel for use as a renewable energy source.The Life Cycle Impact Assessment (LCIA) including midpoint impact analysis that was performed shows that the use of fertilizers is the action with the highest impact in six of the 10 environmental categories considered, representing between 51% and 68% of the impact in these categories.The second most important impact is produced when the diesel is used in tractors and transport vehicles which represents between 48% and 77%. The contribution of the B. carinata cropping system to the global warming category is 12.7 g CO₂ eq. MJ⁻¹ biomass produced. Assuming a preliminary estimation of the B. carinata capacity of translocated CO₂ (631 kg CO₂ ha⁻¹) from below-ground biomass into the soil, the emissions are reduced by up to 5.2 g CO₂ eq. MJ⁻¹.The production and transport are as far as a thermoelectric plant of the B. carinata biomass used as a solid fuel consumes 0.12 MJ of primary energy per 1 MJ of biomass energy stored. In comparison with other fossil fuels such as natural gas, it reduces primary energy consumption by 33.2% and greenhouse gas emission from 33.1% to 71.2% depending on whether the capacity of translocated CO₂ is considered or not.The results of the analysis support the assertion that B. carinata crops are viable from an energy balance and environmental perspective for producing lignocellulosic solid fuel destined for the production of energy in southern Europe. Furthermore, the performance of the crop could be improved, thus increasing the energy and environmental benefits.     

LCA of poplar bioenergy system compared with Brassica carinata energy crop and natural gas in regional scenario

The poplar bioenergy system has been analysed applying life cycle assessment (LCA) to compare its environmental performance to: Ethiopian mustard bioenergy system and natural gas. The life cycle impact assessment (LCIA) shows that the use of fertilizers is the highest impact in four of the 10 environmental categories, representing between 39% and 67% of the impact in them. The diesel used in transport vehicles and agricultural tractors also has a significant impact in another five of the 10 analysed categories 40–85%. The poplar bioenergy system contributes to global warming with 1.90–1.98 g CO₂ eq MJ^?1 biomass produced. The production and transport as far as the thermoelectric plant of the poplar biomass consumes 0.02 MJ of primary energy per 1 MJ of biomass stored. In comparison with Ethiopian mustard and natural gas, it reduces primary energy consumption by 83% and 89% and the greenhouse gas emission by 84% and 89%, respectively. The results of the analysis support that the poplar bioenergy system is viable from an energy balance and environmental perspective for producing energy in southern Europe, as long as it is cultivated in areas where water is available. This latter point and the better environmental performance of both crops in comparison to natural gas allows us to affirm that the combination of several crops adapted to the local agro-climatic conditions of the territory will be the most suitable strategy in Mediterranean areas that wish to reach the global energy production targets in terms of biomass established by the European Union (EU).     

Understanding energy systems change in Canada: 1. Decomposition of total energy intensity

Between 1995 and 2010, the total energy intensity (E/GDP, PJ/Gross Domestic Product in 2002$) of the Canadian economy declined by 23% or − 2.64 MJ/$. To understand why, the Logarithmic Mean Divisia Index (LMD-I) method was used to decompose a large body of government statistical data supporting the observed E/GDP decline. The analysis shows that (a) 48% (1.27 MJ/$) of the decline was associated with an inter-sector structural change in the economy (i.e. an increased contribution to the total GDP of the low energy-using commercial and institutional sector compared with the high energy-using manufacturing and heavy industry sectors); (b) 24% (0.62 MJ/$) was attributed to the impact of the Canadian GDP growing faster than population; (c) 22% (0.58 MJ/$) of the decline was associated with an overall decrease in business energy intensity. A deeper analysis of business sectors shows a positive impact of 0.4 MJ/$ from increased energy intensity in the oil and gas sector, offset by a 0.98 MJ/$ decline due to energy intensity declines in the other business sectors; (d) 6.3% (0.17 MJ/$) of the decline was associated with an improvement in the energy intensity of households, mostly from residential energy use rather than personal transportation energy use. These results provide insights for policy makers regarding those aspects of the Canadian economy that contribute to, or work against, efforts to transform energy systems toward sustainability.     

Banana biomass as potential renewable energy resource: A Malaysian case study

The world has been relying on fossil fuels as its primary source of energy. This unsustainable energy source is not going to last long and thus, gradual shift towards green renewable energy should be practiced. In Malaysia, even though fossil fuel dominates the energy production, renewable energies such as hydropower and biomass are gaining popularity due to the implementation of energy policies and greater understanding on the importance of green energy. Malaysia has been well endowed with natural resources in areas such as agriculture and forestry. Thus, with the availability of feedstock, biomass energy is practical to be conducted and oil palm topped the ranking as biomass source here because of its high production. However, new sources should be sought after as to avoid the over dependency on a single source. Hence, other agriculture biomass should be considered such as banana plant biomass. This paper will discuss on its potential as a new biomass source in Malaysia. Banana plant is chosen as the subject due to its availability, high growth rates, carbon neutrality and the fact that it bears fruit only once a lifetime. Conversion of the biomass to energy can be done via combustion, supercritical water gasification and digestion to produce thermal energy and biogas. The theoretical potential power generation calculated reached maximum of 950 MW meeting more than half of the renewable energy requirement in the Fifth Fuel Policy (Eighth Malaysia Plan 2001–2005). Thus, banana biomass is feasible as a source of renewable energy in Malaysia and also other similar tropical countries in the world.     

Biomass production potentials in Central and Eastern Europe under different scenarios

A methodology for the assessment of biomass potentials was developed and applied to Central and Eastern European countries (CEEC). Biomass resources considered are agricultural residues, forestry residues, and wood from surplus forest and biomass from energy crops. Only land that is not needed for food and feed production is considered as available for the production of energy crops. Five scenarios were built to depict the influences of different factors on biomass potentials and costs. Scenarios, with a domination of current level of agricultural production or ecological production systems, show the smallest biomass potentials of 2–5.7 EJ for all CEEC. Highest potentials can reach up to 11.7 EJ (85% from energy crops, 12% from residues and 3% from surplus forest wood) when 44 million ha of agricultural land become available for energy crop production. This potential is, however, only realizable under high input production systems and most advanced production technology, best allocation of crop production over all CEEC and by choosing willow as energy crops. The production of lignocellulosic crops, and willow in particular, best combines high biomass production potentials and low biomass production costs. Production costs for willow biomass range from 1.6 to 8.0 €/GJ HHV in the scenario with the highest agricultural productivity and 1.0–4.5 €/GJ HHV in the scenario reflecting the current status of agricultural production. Generally the highest biomass production costs are experienced when ecological agriculture is prevailing and on land with lower quality. In most CEEC, the production potentials are larger than the current energy use in the more favourable scenarios. Bulk of the biomass potential can be produced at costs lower than 2 €/GJ. High potentials combined with the low cost levels gives CEEC major export opportunities.     

Estimates of technically available woody biomass feedstock from natural forests and willow biomass crops for two locations in New York State

A Geographic Information System (GIS) was used to estimate the technically available woody biomass from forests and willow biomass crops within a 40 km radius of Syracuse and Tupper Lake, NY. Land cover and land use data were used to identify the available land base and restrictions were applied for slope, parcel size and designated wetlands. Approximately 222,984 oven-dry tonnes (odt) of forest biomass are technically available annually around Syracuse, from 165,848 hectares (ha) of timberland. There are 67,880 ha of agricultural land technically available for growing willow biomass crops, which could produce 38,181 odt yr^?1 if 5% of this land was used and yields were 11.25 odt ha^?1 yr^?1. There are approximately 215,300 odt of forest biomass technically available annually around Tupper Lake from 211,500 ha of timberland. There are 781 ha of technically available agricultural land in this area so willow biomass production would be minimal. While these two areas have different land cover and land use characteristics, both have the potential to produce significant amounts of woody biomass.     

Modeling the land requirements and potential productivity of sugarcane and jatropha in Brazil and India using the LPJmL dynamic global vegetation model

The governments of Brazil and India are planning a large expansion of bioethanol and biodiesel production in the next decade. Considering that limitation of suitable land and/or competition with other land uses might occur in both countries, assessments of potential crop productivity can contribute to an improved planning of land requirements for biofuels under high productivity or marginal conditions. In this paper we model the potential productivity of sugarcane and jatropha in both countries. Land requirements for such expansions are calculated according to policy scenarios based on government targets for biofuel production in 2015. Spatial variations in the potential productivity lead to rather different land requirements, depending on where plantations are located. If jatropha is not irrigated, land requirements to fulfill the Indian government plans in 2015 would be of 410 000 to 95 000 km² if grown in low or high productivity areas respectively (mean of 212 000 km²). In Brazil land requirements, are of 18 000–89 000 km² (mean of 29 000 km²), suggesting a promising substitute to soybean biodiesel. Although future demand for sugarcane ethanol in Brazil is approximately ten times larger than in India, land requirements are comparable in both countries due to large differences in ethanol production systems. In Brazil this requirement ranges from 25 000 to 211 000 km² (mean of 33 000 km²) and in India from 7000 to 161 000 km² (mean 17 000 km²). Irrigation could reduce the land requirements by 63% and 41% (24% and 15%) in India (Brazil) for jatropha and sugarcane respectively.     

Options of biofuel trade from Central and Eastern to Western European countries

Central and Eastern European countries (CEEC) have a substantial biomass production and export potential. The objective of this study is to assess whether the market for biofuels and trade can be profitable enough to realize a supply of biofuels from the CEEC to the European market and to estimate the cost performance of the energy carriers delivered. Five NUTS-2 (Nomenclature d'Unités Territoriales Statistiques) regions with high biomass production potentials in Poland, Romania, Hungary and the Czech Republic were analysed for biofuel export options. From these regions pellets from willow can be provided to destination areas in Western European countries (WEC) at costs of 105.2–219.8 € t^?1. Ethanol can be provided at 11.95–20.89 € per GJ if the biomass conversion is performed at the destination areas in the WEC or at 14.84–17.83 € GJ^?1J if the biomass to ethanol conversion takes place (at small scale) at the CEEC region where the biomass is produced. Short sea shipping shows most cost advantages for longer distance international transport compared to inland waterway shipping and railway. Another reason for lower biofuel supply costs are shorter distances between the regions of biomass production and the destination areas. Therefore the Szczecin region in Poland, closely located to the Baltic Sea, shows a better economic performance for long distance trade of biomass production than the selected region in Hungary (‘land-locked’). It is concluded that in future key CEEC regions can supply (pre-treated) biomass and biofuels to the European market at cost levels, which are sound and attractive to current and expected diesel and gasoline prices.     

The economical and environmental performance of miscanthus and switchgrass production and supply chains in a European setting

The purpose of this study is to analyse the economical and environmental performance of switchgrass and miscanthus production and supply chains in the European Union (EU25), for the years 2004 and 2030. The environmental performance refers to the greenhouse gas (GHG) emissions, the primary fossil energy use and to the impact on fresh water reserves, soil erosion and biodiversity. Analyses are carried out for regions in five countries. The lowest costs of producing (including storing and transporting across 100 km) in the year 2004 are calculated for Poland, Hungary and Lithuania at 43–64 € per oven dry tonne (odt) or 2.4–3.6 € GJ^?1 higher heating value. This cost level is roughly equivalent to the price of natural gas (3.1 € GJ^?1) and lower than the price of crude oil (4.6 € GJ^?1) in 2004, but higher than the price of coal (1.7 € GJ^?1) in 2004. The costs of biomass in Italy and the United Kingdom are somewhat higher (65–105 € odt^?1 or 3.6–5.8 € GJ^?1). The doubling of the price of crude oil and natural gas that is projected for the period 2004–2030, combined with nearly stable biomass production costs, makes the production of perennial grasses competitive with natural gas and fossil oil. The results also show that the substitution of fossil fuels by biomass from perennial grasses is a robust strategy to reduce fossil energy use and curb GHG emissions, provided that perennial grasses are grown on agricultural land (cropland or pastures). However, in such case deep percolation and runoff of water are reduced, which can lead to overexploitation of fresh water reservoirs. This can be avoided by selecting suitable locations (away from direct accessible fresh water reservoirs) and by limiting the size of the plantations. The impacts on biodiversity are generally favourable compared to conventional crops, but the location of the plantation compared to other vegetation types and the size and harvesting regime of the plantation are important variables.     

The influence of CO2 mitigation incentives on profitability of eucalyptus production on clay settling areas in Florida

Fast growing, short-rotation tree crops provide unique opportunities to sequester carbon on phosphate-mined lands in central Florida and, if used as a biofuel, can reduce CO₂ emissions associated with electricity generation. Base case land expectation values (LEVs) of phosphate-mined land under Eucalyptus amplifolia (EA) forestry range from 762 to 6507 $ ha^?1 assuming real discount rates of 10% and 4%, respectively. Assuming 5 $ Mg^?1 C, these LEVs increase from 3% to 24% with incentives for in situ carbon sequestration benefits, or 21% to 73% given in situ carbon sequestration with additional incentives for reducing CO₂ emissions through the use of EA as an energy feedstock. Potential benefits from below-ground C sequestration and mine land reclamation are estimated to be worth an additional 5642–11,056 $ ha^?1.     

Integration of algae-based biofuel production with an oil refinery: Energy and carbon footprint assessment

Biofuel production from algae feedstock has become a topic of interest in the recent decades since algae biomass cultivation is feasible in aquaculture and does therefore not compete with use of arable land. In the present work, hydrothermal liquefaction of both microalgae and macroalgae is evaluated for biofuel production and compared with transesterifying lipids extracted from microalgae as a benchmark process. The focus of the evaluation is on both the energy and carbon footprint performance of the processes. In addition, integration of the processes with an oil refinery has been assessed with regard to heat and material integration. It is shown that there are several potential benefits of co-locating an algae-based biorefinery at an oil refinery site and that the use of macroalgae as feedstock is more beneficial than the use of microalgae from a system energy performance perspective. Macroalgae-based hydrothermal liquefaction achieves the highest system energy efficiency of 38.6%, but has the lowest yield of liquid fuel (22.5 MJ per 100 MJ_algae) with a substantial amount of solid biochar produced (28.0 MJ per 100 MJ_algae). Microalgae-based hydrothermal liquefaction achieves the highest liquid biofuel yield (54.1 MJ per 100 MJ_algae), achieving a system efficiency of 30.6%. Macro-algae-based hydrothermal liquefaction achieves the highest CO₂ reduction potential, leading to savings of 24.5 resp 92 kt CO_2eq/year for the two future energy market scenarios considered, assuming a constant feedstock supply rate of 100 MW algae, generating 184.5, 177.1 and 229.6 GWh_biochar/year, respectively. Heat integration with the oil refinery is only possible to a limited extent for the hydrothermal liquefaction process routes, whereas the lipid extraction process can benefit to a larger extent from heat integration due to the lower temperature level of the process heat demand.     

Heat and power demands in babassu palm oil extraction industry in Brazil

The objective of this paper is to analyze the energy use profile of the babassu (Orbignya ssp—Palmae) oil extraction industry in Brazil in order to establish the basis for a cogeneration study of this important part of the Brazilian Northeast region economy, which is still ignored by energetic biomass studies. The work used information from new equipment suppliers that was analyzed against field information from operating units. The data was used to establish a basis for the thermal and mechanical energy consumption for the two main basic unit profiles for the sector: a simple one with just oil extraction and the other, more vertically integrated with other secondary by-products. For the energetic demand taken from the only oil extraction unit profile study, the minimum pressure for the steam process was estimated at 1.4 MPa, electric demand at 5.79 kW/ton of processed kernel and heat consumption at 2071 MJ/ton of processed kernel (829 kg steam/ton of processed kernel). For the vertically integrated unit profile, the following values were found: minimum pressure for the steam process 1.4 MPa, electric demand 6.22 kW/ton of processed kernel and heat consumption 21,503 MJ/ton of processed kernel (7600 kg steam/ton of processed kernel).     

Cogeneration potential in the Columbian palm oil industry: Three case studies

The palm oil mills are characterized by the availability of considerable amounts of by-products of high-energy value such as empty fruit bunches (EFB), fibers, shells and liquid effluents with high content of organics called palm oil mill effluent (POME). A palm oil mill produces residues equivalent to almost three times the amount of oil produced by biomass, showing a huge potential for increasing the power efficiency of the plants and installed power, mainly by the use of by-products in cogeneration plants with high steam parameters and by reducing steam consumption in process. The objective of this paper is to present the results of the study about the cogeneration potential for three representative palm oil mills located in two important palm oil producing regions in Colombia (South-America), fifth palm oil producers of the world. The sizing of the cogeneration system was made assuming it operation during the greatest possible number of hours throughout the year (based on the seasonal availability of fruit) considering parameters for the steam at 2 MPa and 350 °C, using a condensing-extraction turbine. The balance of mass and energy was made by using the Gate Cycle Enter Software, version 5.51, to estimate the potential of electricity generation. The results showed that for fresh fruit bunch (FFB) processing capacities between 18 and 60 t FFB h⁻¹, it is possible to have surplus power ranging between 1 and 7 MW, if the plants are self-sufficient in electric energy and steam for process. With an average Capacity Factor (approximately 0.4), it is possible to expect a generation index of 75 and 160 kWh t⁻¹ FFB when the processing plant is operating or shutdown, respectively, 3 or 4 times better than when a traditional system with a back-pressure steam turbines is used. This analysis used up to 60% of EFB produced in plant as fuel, considering its value as fertilizer for the palm crop. Several economic conditions were considered to estimate the economic and technical feasibility of cogeneration systems in palm oil mill for Colombian palm oil sector.     

Exploration of regional and global cost–supply curves of biomass energy from short-rotation crops at abandoned cropland and rest land under four IPCC SRES land-use scenarios

We explored the production cost of energy crops at abandoned agricultural land and at rest land at a regional and a global level to the year 2050 using four different land-use scenarios. The estimations were based on grid cell data on the productivity of short-rotation crops on the available land over time and assumptions regarding the capital and the labour input required to reach these productivity levels. It was concluded that large amounts of grown biomass at abandoned agricultural land and rest land, 130–270 EJ yr^?1 (about 40–70% of the present energy consumption) may be produced at costs below $2 GJ^?1 by 2050 (present lower limit of cost of coal). Interesting regions because of their low production cost and significant potentials are the Former USSR, Oceania, Eastern and Western Africa and East Asia. Such low costs presume significant land productivity improvements over time and cost reductions due to learning and capital-labour substitution. An assessment of biomass fuel cost, using the primary biomass energy costs, showed that the future costs of biomass liquid fuels may be in the same order of the present diesel production costs, although this may change in the long term. Biomass-derived electricity costs are at present slightly higher than electricity baseload costs and may directly compete with estimated future production costs of fossil fuel electricity with CO₂ sequestration. The present world electricity consumption of around 20 PWh yr^?1 may be generated in 2050 at costs below $45 MWh^?1 in A1 and B1 and below $55 MWh^?1 in A2 and B2. At costs of $60 MWh^?1, about 18 (A2) to 53 (A1) PWh yr^?1 can be produced.