Numerical study of an exhaust heat recovery system using corrugated tube heat exchanger with twisted tape inserts

The purpose of this work is to investigate gas to liquid heat transfer performance of concentric tube heat exchanger with twisted tape inserted corrugated tube and to evaluate its impact on engine performance and economics through heat recovery from the exhaust of a heavy duty diesel generator (120 ekW rated load). This type of heat exchanger is expected to be inexpensive to install and effective in heat transfer and to have minimal effect on exhaust emissions of diesel engines. This type of heat exchanger has been investigated for liquid to liquid heat transfer at low Reynolds number by few investigators, but not for gas to liquid heat transfer. In this paper, a detail of heat transfer performance is investigated through simulations using computer software. The software is first justified by comparing the simulation results with the developed renowned correlations. Simulations are then conducted for concentric tube heat exchanger with different twisted tape configuration for optimal design. The results show that the enhancement in the rate of heat transfer in annularly corrugated tube heat exchanger with twisted tape is about 235.3% and 67.26% when compared with the plain tube and annularly corrugated tube heat exchangers without twisted tapes respectively. Based on optimal results, for a 120 ekW diesel generator, the application of corrugated tube with twisted tape concentric tube heat exchanger can save 2250 gal of fuel, $11,330 of fuel cost annually and expected payback of 1 month. In addition, saving in heating fuel also reduces in CO₂ emission by 23 metric tons a year.     

A novel polygeneration system integrating the acetylene production process and fuel cell

This paper presents a novel polygeneration system that integrates the acetylene process and the use of fuel cells. The system produces acetylene and power by a process of the partial oxidation/combustion (POC) of natural gas process, a water–gas shift reactor, a fuel cell and a waste heat boiler auxiliary system to recover the exhaust heat and gas from the fuel cell. Based on 584.3 kg/h of natural gas feedstock, a POC reactor temperature of 1773 K, an absorber pressure of 1.013 MPa and a degasser pressure of 0.103 MPa, the simulation results show that the new system achieved acetylene production of 1.9 MW, net electricity production of 1.7 MW, power generation efficiency of 26.8% and exergy efficiency of 43.4%, which was 20.2% higher than the traditional acetylene production process. The new system's exergy analysis and the flow rate of the products were investigated, and the results revealed that the energy conversion and systematic integration mechanism demonstrated the improvement of natural gas energy conversion efficiency.     

Numerical analysis of the tubular heat exchanger designed for co-generating units on the basis of microturbines

The application of numerical simulations using the computational fluid dynamics (CFD) analysis when mapping processes in the course of which the heat transmission occurs has become an essential part of the heat transfer systems. The present contribution deals with the possibility to use the waste heat of the flue gas produced by small microturbines. The waste heat is mapped by means of both the numerical simulations applying the FLUENT software and the practical experiment. Utilizing a part of the waste heat for water heating and decreasing the outlet temperature of the flue gas into atmosphere when applying in co-generating units represents one of the partial benefits. The present paper brings information concerning the newly designed type of heat exchanger including the results of its numerical analysis.The analysed heat exchanger designed in the system with microturbine (MT) C30 reached generally the efficiency of 75%. Both the results of simulations and the carried out practical experiment confirmed the temperature of the flue gas to be sufficient behind the exchanger to prevent the condensation of water from the flue gas. On the contrary, except for heating water the exchanger under consideration offers – thanks to its design – also other possibilities to use of the flue gas. The practical experiment confirmed the results of the CFD prediction with rather small differences as the temperature of water obtained from the exchanger was 359 K and the designed shape of the exchanger did not result in substantial pressure losses in flue gas approximately 50 Pa. The mean logarithmic temperature difference of the mapped and verified exchanger was ～203 K.     

Investigation of heat transfer and pressure drop in plate heat exchangers having different surface profiles

It would be misleading to consider only cost aspect of the design of a heat exchanger. High maintenance costs increase total cost during the services life of heat exchanger. Therefore exergy analysis and energy saving are very important parameters in the heat exchanger design. In this study, the effects of surface geometries of three different type heat exchangers called as PHE_flat (Flat plate heat exchanger), PHE_corrugated (Corrugated plate heat exchanger) and PHE_asteriks (Asterisk plate heat exchanger) on heat transfer, friction factor and exergy loss were investigated experimentally. The experiments were carried out for a heat exchanger with single pass under condition of parallel and counter flow. In this study, experiments were conducted for laminar flow conditions. Reynolds number and Prandtl number were in the range of 50 ? Re ? 1000 and 3 ? Pr ? 7, respectively. Heat transfer, friction factor and exergy loss correlations were obtained according to the experimental results.     

Assessment of thermoelectric module with nanofluid heat exchanger

For applications such as cooling of electronic devices, it is a common practice to sandwich the thermoelectric module between an integrated chip and a heat exchanger, with the cold-side of the module attached to the chip. This configuration results thermal contact resistances in series between the chip, module, and heat exchanger. In this paper, an appraisal of thermal augmentation of thermoelectric module using nanofluid-based heat exchanger is presented. The system under consideration uses commercially available thermoelectric module, 27 nm Al₂O₃–H₂O nanofluid, and a heat source to replicate the chip. The volume fraction of nanofluid is varied between 0% and 2%. At optimum input current conditions, experimental simulations were performed to measure the transient and steady-state thermal response of the module to imposed isoflux conditions. Data collected from the nanofluid-based exchanger is compared with that of deionized water.Results show that there exist a lag-time in thermal response between the module and the heat exchanger. This is attributed to thermal contact resistance between the two components. A comparison of nanofluid and deionized water data reveals that the temperature difference between the hot- and cold-side, ΔT = T_h ? T_c ≈ 0, is almost zero for nanofluid whereas ΔT > 0 for water. When ΔT ≈ 0, the contribution of Fourier effect to the overall heating is approximately zero hence enhancing the module cooling capacity. Experimental evidence further shows that temperature gradient across the thermal paste that bonds the chip and heat exchanger is much lower for the nanofluid than for deionized water. Low temperature gradient results in low resistance to the flow of heat across the thermal paste. The average thermal contact resistance, R = ΔT/Q, is 0.18 and 0.12 °C/W, respectively for the deionized water and nanofluid. For the range of optimum current, 1.2 ? current ? 4.1 A, considered in this study, the COP ranges between 1.96 and 0.68.     

Heat recovery from Diesel engines: A thermodynamic comparison between Kalina and ORC cycles

In the context of heat recovery for electric power generation, Kalina cycle (a thermodynamic cycle using as working fluid a mixture of water and ammonia) and Organic Rankine Cycle (ORC) represent two different eligible technologies. In this work a comparison between the thermodynamic performances of Kalina cycle and an ORC cycle, using hexamethyldisiloxane as working fluid, was conducted for the case of heat recovery from two Diesel engines, each one with an electrical power of 8900 kWe. The maximum net electric power that can be produced exploiting the heat source constituted by the exhaust gases mass flow (35 kg/s for both engines, at 346 °C) was calculated for the two thermodynamic cycles. Owing to the relatively low useful power, for the Kalina cycle a relatively simple plant layout was assumed. Supposing reasonable design parameters and a logarithmic mean temperature difference in the heat recovery exchanger of 50 °C, a net electric power of 1615 kW and of 1603 kW respectively for the Kalina and for the ORC cycle was calculated.Although the obtained useful powers are actually equal in value, the Kalina cycle requires a very high maximum pressure in order to obtain high thermodynamic performances (in our case, 100 bar against about 10 bar for the ORC cycle). So, the adoption of Kalina cycle, at least for low power level and medium–high temperature thermal sources, seems not to be justified because the gain in performance with respect to a properly optimized ORC is very small and must be obtained with a complicated plant scheme, large surface heat exchangers and particular high pressure resistant and no-corrosion materials.     

Influence of packed honeycomb ceramic on heat extraction rate of packed bed embedded heat exchanger and heat transfer modes in heat transfer process

Under the condition that the transient oxidation heat extraction process of coal mine ventilation air methane (VAM) is equivalent to a series of steady state process, the steady state heat extraction experiment platform is built. The influence of the honeycomb ceramic packed in heat extraction zone and its two-side space on heat extraction rate and heat transfer modes is investigated. The experimental results show that the honeycomb ceramic packed in heat extraction zone two-side space can always strengthen heat extract ion of heat exchanger by increasing gas physical flow velocity in bed and radiation heat exchanging area and disturbing heat exchanger leeward side flow field. The contradictory dual characteristic of the influence of the honeycomb ceramic packed in heat extraction zone on heat exchanger heat extraction rate determines that the honeycomb ceramic has no great influence on heat extraction rate and doesn't always strengthen heat exchanger heat extraction. Contribution of heat transfer modes on packed bed embedded heat exchanger heat extraction is investigated using the method of coating heat exchanger outer surface silver; the experimental result shows that 55% contribution of packed bed embedded heat exchanger heat extraction rate is from radiation when gas mass flow rate is 0.15 kg·s^− 1·m^− 2 and its temperature is 1113 k; with the gas temperature being increased further, radiation will become the main way of packed bed embedded heat exchanger heat extraction.     

Optimization of finned-tube heat exchangers for diesel exhaust waste heat recovery using CFD and CCD techniques

In this paper, response surface methodology (RSM) based on central composite design (CCD) is applied to obtain an optimization design of finned type heat exchangers (HEX) to recover waste heat from the exhaust of a diesel engine. The design is performed for a single point operation (1600 rpm and 60 N m) of an OM314 diesel engine obtained from experimental measurements. Based on the CCD principle, fifteen HEX cases with different fins height, thickness and number are modeled numerically and the optimization is done to have the maximum heat recovery amount and minimum of pressure drop along the heat exchanger.     

Solid/vapour sorption heat transformer: Design and performance

A high temperature high lift solid sorption based heat transformer has been successfully designed and tested. The sorption reactor concept is based on a tube-fin heat exchanger where the heat exchanging fluids can flow through the hollow fins. The plates were brazed together with porous metal foam that was impregnated with either of the sorbents, LiCl and MgCl₂. The adsorbate is ammonia. The batch system was tested as to the power delivered at high temperatures, 150–200 °C. Peak power at 200 °C was about 0.8 kW, the average power about 0.4 kW. The thermal efficiency, COP, was calculated from the experimental results to be 0.11. This is only 40% of the expected theoretical value and can largely be attributed to the thermal mass of the reactor.     

Modeling of shell and tube heat recovery exchanger operated with nanofluid based coolants

The emergence of several challenging issues such as climate change, fuel price hike and fuel security have become hot topics around the world. Therefore, introducing highly efficient devices and heat recovery systems are necessary to overcome these challenges. It is reported that a high portion of industrial energy is wasted as flue gas from heating plants, boilers, etc. This study has focused on the application of nanofluids as working fluids in shell and tube heat recovery exchangers in a biomass heating plant. Heat exchanger specification, nanofluid properties and mathematical formulations were taken from the literature to analyze thermal and energy performance of the heat recovery system. It was observed that the convective and overall heat transfer coefficient increased with the application of nanofluids compared to ethylene glycol or water based fluids. It addition, 7.8% of the heat transfer enhancement could be achieved with the addition of 1% copper nanoparticles in ethylene glycol based fluid at a mass flow rate of 26.3 and 116.0 kg/s for flue gas and coolant, respectively.     

Unsteady fluid mechanics and heat transfer study in a double-tube air–combustor heat exchanger with porous medium

Fluid mechanics and heat transfer are studied in a double-tube heat exchanger that uses the combustion gases from natural gas in a porous medium located in a cylindrical tube to warm up air that flows through a cylindrical annular space. The mathematical model is constructed based on the equations of continuity, linear momentum, energy and chemical species. Unsteady fluid mechanics and heat transfer by forced gas convection in the porous media, with combustion in the inner tube, coupled to the forced convection of air in the annular cylindrical space are predicted by use of finite volumes method. Numerical simulations are made for four values of the annular air flow Reynolds number in the range 100 ? Re ? 2000, keeping constant the excess air ψ = 4.88, the porosity ε = 0.4, and the air–fuel mixture inlet speed Uo = 0.43 m/s. The results obtained allow the characterization of the velocity and temperature distributions in the inner tube and in the annular space, and at the same time to describe the displacement of the moving combustion zone and the annular porous media heat exchanger thermal efficiency. It is concluded that the temperature increase is directly related to the outer Reynolds number.     

Air heat exchangers with long heat pipes: Experiments and predictions

This paper presents measurements and predictions of a heat pipe-equipped heat exchanger with two filling ratios of R134a, 19% and 59%. The length of the heat pipe, or rather thermosyphon, is long (1.5 m) as compared to its diameter (16 mm). The airflow rate varied from 0.4 to 2.0 kg/s. The temperatures at the evaporator side of the heat pipe varied from 40 to 70 °C and at the condenser part from 20 to 50 °C. The measured performance of the heat pipe has been compared with predictions of two pool boiling models and two filmwise condensation models. A good agreement is found. This study demonstrates that a heat pipe equipped heat exchanger is a good alternative for air–air exchangers in process conditions when air–water cooling is impossible, typically in warmer countries.     

Entropy generation of vapor condensation in the presence of a non-condensable gas in a shell and tube condenser

This article investigates the entropy production of condensation of a vapor in the presence of a non-condensable gas in a counter-current baffled shell and one-pass tube condenser. The non-dimensional entropy number is derived with respect to heat exchange between the bulk fluid and condensate, as well as heat exchange between the condensate and coolant. Numerical results show that heat transfer from the condensate to the coolant has a dominant role in generating entropy. For example, at an air mass flow rate of 330 kg/h, 93.4% of the total entropy generation is due to this source. The resultant profiles during the condensation process indicate that a higher air mass flow rate leads to a lower rate of entropy production. For example, as the air mass flow rate increases from 330 kg/h to 660 kg/h and 990 kg/h, the total entropy generation decreases from 976 J/s K to 904 and 857.2 J/s K, respectively. By introducing a new parameter called the condensation effectiveness, a correlation is also developed for predictions of the entropy number, and an illustrative example is presented.     

Life cycle assessment (LCA) of an integrated biomass gasification combined cycle (IBGCC) with CO2 removal

Based on the results of previous studies, the efficiency of a Brayton/Hirn combined cycle fuelled with a clean syngas produced by means of biomass gasification and equipped with CO₂ removal by chemical absorption reached 33.94%, considering also the separate CO₂ compression process. The specific CO₂ emission of the power plant was 178 kg/MW h. In comparison with values previously found for an integrated coal gasification combined cycle (ICGCC) with upstream CO₂ chemical absorption (38–39% efficiency, 130 kg/MW h specific CO₂ emissions), this configuration seems to be attractive because of the possibility of operating with a simplified scheme and because of the possibility of using biomass in a more efficient way with respect to conventional systems. In this paper, a life cycle assessment (LCA) was conducted with presenting the results on the basis of the Eco-Indicator 95 impact assessment methodology. Further, a comparison with the results previously obtained for the LCA of the ICGCC was performed in order to highlight the environmental impact of biomass production with fossil fuels utilisation. The LCA shows the important environmental advantages of biomass utilisation in terms of reduction of both greenhouse gas emissions and natural resource depletion, although an improved impact assessment methodology may better highlight the advantages due to the biomass utilisation.     

Heat transfer and pressure drop properties of high viscous solutions in plate heat exchangers

Heat transfer and pressure drop characteristics of an absorbent salt solution in a commercial plate heat exchanger serving as a solution sub-cooler in the high loop of triple-effect absorption refrigeration cycle was investigated. The main objectives of this research were to establish the correlation equations to predict the heat transfer and pressure drop and to analyze and optimize the operating parameters for use in the design of absorption systems.In order to conduct above studies, a single-pass cross-corrugated ALFA-LAVAL plate heat exchanger, Model PO1-VG, with capacity of 14,650 W (50,000 Btu/h) was used. In order to evaluate the performance, hot solution inlet temperatures from 55 °C (130 °F) to 77 °C (170 °F), and inlet temperature differences from 14 °C (25 °F) to 20 °C (35 °F) were used. The cold side of the heat exchanger was operated to match the equal heat capacity rate of hot side.Based on the empirical models proposed in the literature, a program was developed and experimental data were curve fitted. From the best-fitted curves, the power-law equations for heat transfer and pressure losses were established and the performance was evaluated.In the hot salt solution side, the Reynolds number was varied from 250 to 1100 and the resulting Nusselt number varied from 7.4 to 15.8. The measured overall heat transfer coefficient U_overall varied from 970 W/m² °C (170 Btu/h ft² °F) to 2270 W/m² °C (400 Btu/h ft² °F) and the Fanning friction factor in the absorbent side of the heat exchanger varied from 5.7 to 7.6. The correlation equations developed to predict the heat transfer and friction factor perfectly agree with the experimental results. Those equations can be used to predict the performance of any solution with Prandtl numbers between 82 and 174, for heat exchangers with similar geometry.     

Emission reductions potential for energy from municipal solid waste incineration in Chongqing

Municipal solid waste (MSW) is a potential energy resource which can be incineration to energy. Furthermore, it can conserve more valuable fossil fuel and improve the environment by lessening Greenhouse Gas (GHG) emission and the amount of waste that must be landfilled. This paper highlights the MSW generation and characteristics for the city of Chongqing, the nation's fourth largest municipality after Beijing, Shanghai and Tianjin. At present the daily amount of MSW generated per person is about 0.85 kg; food waste accounts for about 53.7% of total MSW. MSW in Chongqing has higher moisture content and lower net caloric value, which is an obstruction for incineration. This paper examines the emission reductions potential for MSW incineration power plant in urban Chongqing. As a case study, emission reductions analysis and economic assessment was implemented for Tongxing MSW incineration power plant. The results show that with the power displacement potential at 235 060 MWh, Chongqing is expected to generate emission reductions as much as 815 862–827 969 tCO₂ and net profit US$7.72 million per annum.     

Study on solar/waste heat driven multi-bed adsorption chiller with mass recovery

The study deals with a solar or waste heat driven three-bed adsorption cooling cycle employing mass recovery scheme. A cycle simulation computer program is developed to investigate the performance of the chiller. The innovative chiller is driven by exploiting solar/waste heat of temperatures between 60 and 90 °C with a cooling source at 30 °C for air-conditioning purpose. The performance of the three-bed adsorption chiller with mass recovery scheme was compared with that of the three-bed chiller without mass recovery. It is found that cooling effect as well as solar/waste heat recovery efficiency, η of the chiller with mass recovery scheme is superior to those of three-bed chiller without mass recovery for heat source temperatures between 60 and 90 °C. However, COP of the proposed chiller is higher than that of the three-bed chiller without mass recovery, when heat source temperature is below 65 °C.     

Effect of fatty acid composition of soybean oil on deposit and performance of plant oil pressure stoves

Plant oil as household energy could be a sustainable and locally available alternative for fossil fuel. However, the use of pure plant oil in pressure stoves leads to deposit in the vaporizer. Therefore, objective of this study was to investigate the effect of the degree of unsaturation of plant oils on performance and deposit formation. Soybean oil with an iodine value of 128 g I₂/100 g was used as well as partly hydrogenated soybean oil with an iodine value of 62 g I₂/100 g, hydrogenated soybean oil with an iodine value of 1 g I₂/100 g, and a blend of 50% refined soybean oil and 50% partly hydrogenated soybean oil was confected to obtain an iodine value of 95 g I₂/100 g. In burning trials, the specific fuel consumption, the required frequency of nozzle cleaning and the amount of deposit in the vaporizer were measured. Results showed an exponential increase of deposits in the vaporizer when iodine value of soybean oil was increased: deposits amounted to 0.26 g/kg of consumed fuel for hydrogenated soybean oil and 0.70 g/kg for the original (untreated) soybean oil. However, an increase in the soybean oil iodine value did not affect fuel consumption, which was 0.296 kg/h for hydrogenated soybean oil compared to 0.286 kg/h for original (untreated) soybean oil. Further research is necessary to investigate the chemical reactions in the vaporizer to identify key precursors (factors) and reactions mechanisms that could influence the formation of deposits in plant oil pressure stoves.     

Heat transfer,friction factor and effectiveness analysis of Fe3O4/water nanofluid flow in a double pipe heat exchanger with return bend

The convective heat transfer, friction factor and effectiveness of different volume concentrations of Fe₃O₄ nanofluid flow in an inner tube of double pipe heat exchanger with return bend has been estimated experimentally and turbulent flow conditions. The test section used in this study is of double pipe type in which the inner tube diameter is 0.019 m, the annulus tube diameter is 0.05 m and the total length of inner tube is 5 m. At a distance of 2.2 m from the inlet of the inner tube the return bend is provided. The hot Fe₃O₄ nanofluid flows through an inner tube, where as the cold water flows through an annulus tube. The volume concentrations of the nanoparticles used in this study are 0.005%, 0.01%, 0.03% and 0.06% with Reynolds number range from 15,000 to 30,000. Based on the results, the Nusselt number enhancement is 14.7% for 0.06% volume concentration of nanofluid flow in an inner tube of heat exchanger at a Reynolds number of 30,000 when compared to base fluid data; the pumping penalty of nanofluid is < 10%. The effectiveness of heat exchanger for water and nanofluid flow is explained in terms of number of transfer units (NTU) in order to estimate the overall performance of the double pipe heat exchanger. New correlations for Nusselt number and friction factor have been developed based on the experimental data.     

Experimental study on a small Brayton air refrigerator under −120 °C

A small Brayton air refrigerator with high-speed gas bearing turbo-expander and compact plate-fin heat exchanger was designed and fabricated. Performances of the two key components (turbo-expander and heat exchanger) and the refrigerator as a whole were investigated. The bearings used in the refrigerator were compliant foil journal bearings with elastic support, and stability inspection was conducted on them. The results indicate that the refrigerator had a high cooling capability, and that the gas bearings used here achieved good performance in a wide speed region up to 250,000 rpm. While the expander operated at its design speed (220,000 rpm), the refrigerator had a cooling capacity of 1500 W at ?80 °C, and the lowest no-load refrigeration temperature of ?124.5 °C was obtained. Moreover, the influence of nozzle number and velocity ratio on the turbo-expander and the effect of flow rate and cold inlet temperature on the heat exchanger are discussed in detail.