Fabrication of a Flat Tubular Segmented‐in‐series Solid Oxide Fuel Cell Using Decalcomania Paper

A flat tubular segmented‐in‐series (SIS) solid oxide fuel cell (SOFC) was fabricated using decalcomania paper. The performance of a two‐cell stack with 4.5‐mm‐wide electrodes was investigated in a temperature range of 650–800 °C. The decalcomania paper allowed fabrication of the SIS‐SOFC on all sides of the flat tubular support and achieve an effective electrode area larger than that obtained using typical SOFC fabrication techniques such as screen printing or slurry coating. SEM observations revealed that each component layer was flat, uniformly thick, and well adherent to adjacent layers. Measured values of open circuit voltages were very close to the theoretical values; confirming that the processing technique utilizing decalcomania paper is suitable for SIS‐SOFC fabrication. The power densities of the two‐cell‐stack were 437.4, 375.6, 324.6, and 257.1 mW cm⁻² at 800, 750, 700 and 650 °C, respectively.     

Development and Fabrication of a New Concept Planar‐tubular Solid Oxide Fuel Cell (PT‐SOFC)

The paper reports a new concept of planar‐tubular solid oxide fuel cell (PT‐SOFC). Emphasis is on the fabrication of the required complex configuration of Ni‐yttria‐stabilised zirconia (YSZ) porous anode support by tert‐butyl alcohol (TBA) based gelcasting, particularly the effects of solid loading, amounts of monomers and dispersant on the rheological behaviour of suspension, the shrinkage of a wet gelcast green body upon drying, and the properties of final sample after sintering at 1350 °C and reduction from NiO‐YSZ to Ni‐YSZ. The results show that the gelcasting is a powerful method for preparation of the required complex configuration anode support. The anode support resulted from an optimised suspension with the solid loading of 25 vol% has uniform microstructure with 37% porosity, bending strength of 44 MPa and conductivity of 300 S cm^—1 at 700 °C, meeting the requirements for an anode support of SOFC. Based on the as‐prepared anode support, PT‐SOFC single cell of Ni‐YSZ/YSZ/LSCF has been fabricated by slurry coating and co‐sintering technique. The cell peak power density reaches 63, 106 and 141 mW cm^—2 at 700, 750 and 800 °C, respectively, using hydrogen as fuel and ambient air as oxidant.     

A Novel Cell‐Array Design for Single Chamber SOFC Microstack

A novel design of single chamber solid oxide fuel cell (SC‐SOFC) microstack with cell‐array arrangement is fabricated and operated successfully in a methane–oxygen–nitrogen mixture. The small stack, consisting of five anode‐supported single cells connected in series, exhibits an open circuit voltage (OCV) of 4.74 V at the furnace temperature of 600 °C and a maximum power output of 420 mW (total active electrode area is 1.4 cm²) at the furnace temperature of 700 °C. A gas mixture of CH₄/O₂ = 1 leads to best performance and stability.     

Fabrication and Characterization of Anode‐Supported Low‐Temperature SOFC Based on Gd‐Doped Ceria Electrolyte

Large‐size, 9.5 cm × 9.5 cm, Ni‐Gd_0.1Ce_0.9O_1.95 (Ni‐GDC) anode‐supported solid oxide fuel cell (SOFC) has been successfully fabricated with NiO‐GDC anode substrate prepared by tape casting method and thin‐film GDC electrolyte fabricated by screen‐printing method. Influence of the sintering shrinkage behavior of NiO‐GDC anode substrate on the densification of thin GDC electrolyte film and on the flatness of the co‐sintered electrolyte/anode bi‐layer was studied. The increase in the pore‐former content in the anode substrate improved the densification of GDC electrolyte film. Pre‐sintering temperature of the anode substrate was optimized to obtain a homogeneous electrolyte film, significantly reducing the mismatch between the electrolyte and anode substrate and improving the electrolyte quality. Dense GDC electrolyte film and flat electrolyte/anode bi‐layer can be fabricated by adding 10 wt.% of pore‐former into the composite anode and pre‐sintering it at 1,100 °C for 2 h. Composite cathode, La_0.6Sr_0.4Fe_0.8Co_0.2O₃, and GDC (LSCF‐GDC), was screen‐printed on the as‐prepared electrolyte surface and sintered to form a complete single cell. The maximum power density of the single cell reached 497 mW cm^–2 at 600 °C and 953 mW cm^–2 at 650 °C with hydrogen as fuel and air as oxidant.     

Performance of Cobalt‐free La0.6Sr0.4Fe0.9Ni0.1O3–δ Cathode Material for Intermediate Temperature Solid Oxide Fuel Cells

A series of cobalt‐free perovskite‐type cathode materials La_0.6Sr_0.4Fe_1–xNi_xO_3–δ (0 ≤ x ≤ 0.15) for intermediate temperature solid oxide fuel cells (IT‐SOFCs) are prepared by a citric‐nitrate process. The conductivities of the cathode materials are measured as functions of temperature (300–800 °C) in air by AC impedance method, and the La_0.6Sr_0.4Fe_0.9Ni_0.1O_3–δ (LSFN10) has the highest conductivity to be 160 S cm^–1 at 400 °C. A single IT‐SOFC based on LSFN10 cathode, BaZr_0.1Ce_0.7Y_0.2O_3–δ electrolyte membrane and Ni–BaZr_0.1Ce_0.7Y_0.2O_3–δ anode substrate was fabricated by a simple spin‐coating process, and the performances of the cell using hydrogen as fuel and air as the oxidant were researched by electrochemical methods at 600–700 °C. The maximum power densities of the cell are 405 mW cm^–2 at 700 °C, 238 mW cm^–2 at 650 °C, and 140 mW cm^–2 at 600 °C, respectively. The results indicate that the LSFN10 is a promising cathode material for proton conducting IT‐SOFCs.     

Integration of Spin‐Coated Nanoparticulate‐Based La0.6Sr0.4CoO3–δ Cathodes into Micro‐Solid Oxide Fuel Cell Membranes

Thin cathodes for micro‐solid oxide fuel cells (micro‐SOFCs) are fabricated by spin‐coating a suspension of La_0.6Sr_0.4CoO_3–δ (LSC) nanoparticulates obtained by salt‐assisted spray pyrolysis. The resulting 250 nm thin LSC layers exhibit a three‐dimensional porous microstructure with a grain size of around 45 nm and can be integrated onto free‐standing 3 mol.% yttria‐stabilized‐zirconia (3YSZ) electrolyte membranes with high survival rates. Weakly buckled micro‐SOFC membranes enable a homogeneous distribution of the LSC dispersion on the electrolyte, whereas the steep slopes of strongly buckled membranes do not allow for a perfect LSC coverage. A micro‐SOFC membrane consisting of an LSC cathode on a weakly buckled 3YSZ electrolyte and a sputtered Pt anode has an open‐circuit voltage of 1.05 V and delivers a maximum power density of 12 mW cm^–2 at 500 °C.     

Tubular Cathode Prepared by a Dip‐Coating Method for Low Temperature DMFC

A novel tubular cathode for the direct methanol fuel cell (DMFC) is proposed, based on a tubular titanium mesh. A dip‐coating method has been developed for its fabrication. The tubular cathode is composed of titanium mesh, a cathode diffusion layer, a catalyst layer, and a recast Nafion® film. The titanium mesh is present at the inner circumference of the diffusion layer, while the recast Nafion® film is at the outer circumference of the catalyst layer. A DMFC single cell with a 3.5 mgPt cm^–2 tubular cathode was able to perform as well, in terms of power density, as a conventional planar DMFC. A peak power density of 9 mW cm^–2 was reached under atmospheric air at 25 °C.     

Fabrication and operation of flow‐through tubular SOFCs for electric power and synthesis gas cogeneration from methane

Flow‐through type tubular solid oxide fuel cells were successfully fabricated and operated with a single‐chamber configuration for realizing the simultaneous generation of electric power and synthesis gas from methane by integrating a downstream catalyst into the fuel cell reactor. A new operation mode, which completely eliminated the gas diffusion between cathode side and anode side, is proposed. The cell showed high open‐circuit voltages of 1.02–1.08 V at the furnace temperature range of 650–800°C when operating on CH₄‐O₂ gas mixture at a molar ratio of 2:1. A peak power density of approximately 300 mW cm^?2 and a maximum power output of 1.5 W were achieved for a single cell with an effective cathode geometric surface area of 5.4 cm² at the furnace temperature of 750°C. The in‐situ initialization of the cell using CH₄‐O₂ gas mixture was also realized via applying an effective catalyst into the tubular cell. © 2013 American Institute of Chemical Engineers AIChE J, 60: 1036–1044, 2014     

Performance of IT‐SOFC with Ce0.9Gd0.1O1.95 Functional Layer at the Interface of Ce0.9Gd0.1O1.95 Electrolyte and Ni‐Ce0.9Gd0.1O1.95 Anode

In this paper we present results for a high power density IT‐SOFC and a method for dispersing nanosized Ce_0.9Gd_0.1O_1.95 (GDC) particles at the GDC electrolyte and Ni‐GDC anode interface. Dispersed nanosized particles were deposited to form an anode functional layer (AFL). Anode supports were prepared by tape casting of large micron‐sized NiO powder and sub micron‐sized GDC powder without pore former. For the cathode a La_0.6Sr_0.4Co_0.2Fe_0.8O_{3 – δ} (LSCF)‐GDC composite was used. Without an AFL the open circuit potential (OCP) and the maximum power density were 0.677 V and 407 mW cm^–2, respectively, at 650 °C using 30 sccm of hydrogen and air flow‐rate. With an AFL the OCP and the maximum power density increased to 0.796 V and 994 mW cm^–2, respectively, at the same temperature. Two point probe impedance measurements revealed that the AFL fabricated by the proposed method not only increased the OCP but also reduced the electrode polarisation by 68%. The effect of gas flow‐rate is also present in this paper. When hydrogen and air flow‐rate is increased to 90 sccm, the sample with AFL obtained 1.57 W cm^–2 at 650 °C.     

Fabrication of BaZr0.1Ce0.7Y0.2O3 – δ ‐Based Proton‐Conducting Solid Oxide Fuel Cells Co‐Fired at 1,150 °C

Dense proton‐conducting BaZr_0.1Ce_0.7Y_0.2O_{3 – δ} (BZCY) electrolyte membranes were successfully fabricated on NiO–BZCY anode substrates at a low temperature of 1,150 °C via a combined co‐press and co‐firing process. To fabricate full cells, the LaSr₃Co_1.5Fe_1.5O_{10 – δ}–BZCY composite cathode layer was fixed to the electrolyte membrane by two means of one‐step co‐firing and two‐step co‐firing, respectively. The SEM results revealed that the cathode layer bonded more closely to the electrolyte membrane via the one‐step co‐firing process. Correspondingly, determined from the electrochemical impedance spectroscopy measured under open current conditions, the electrode polarisation and Ohmic resistances of the one‐step co‐fired cell were dramatically lower than the other one for its excellent interface adhesion. With humidified hydrogen (2% H₂O) as the fuel and static air as the oxidant, the maximum power density of the one‐step co‐fired single cell achieved 328 mW cm^–2 at 700 °C, showing a much better performance than that of the two‐step co‐fired single cell, which was 264 mW cm^–2 at 700 °C.     

Comparative Performance Analysis of Anode‐Supported Micro‐Tubular SOFCs with Different Current‐Collection Architectures

In this study, the performances of single micro‐tubular solid oxide fuel cells based on the NiO–YSZ/YSZ/LSM system with two different current‐collection architectures were compared. In the first case, a straight Ni wire was inserted within the hole of the cell before the electrochemical testing, and in the second case, a coil integrated‐current collector within the anode layer was already arranged for electrical connections during cell processing. The current produced in each case was collected from double terminal and the performance of the cells was estimated by electrochemical I–V characterization. The maximum power outputs generated in the cells with the integrated‐current collector and the common current‐collection architectures were of ∼200 and ∼55 mW cm^–2, respectively at 800 °C under a wet H₂ fuel flow.     

An Investigation on Dip‐Coating Technique for Fabricating Anode‐Supported Solid Oxide Fuel Cells

To cut down the energy consumption and processing period, Ni‐YSZ anode‐supported thin YSZ electrolyte SOFCs have been fabricated by an improved dip‐coating technique, in which the electrolyte layer was dip‐coated on green anode substrates instead of prefired ones, followed by co‐firing. The film formation mechanisms of dip‐coating were analyzed with liquid entrainment and capillary effect assumptions. According to the mechanisms, a typical YSZ electrolyte slurry formula of conventional dip‐coating technique was modified for the improved technique by increasing the binder content and the solid loading. With the improved dip‐coating technique, along with an optimized electrolyte slurry formula, a SOFC with dense electrolyte, revealing a maximum power density of 460 mW/cm² at 800°C, was obtained. Factors affecting the coating layers were also investigated by SEM and AC impedance analyses.     

Improved Electrodes/Electrolyte Interfaces for Solid Oxide Fuel Cell by Using Dual‐Sized Powders in Electrolyte Slurry

The dense electrolyte film with the rough surfaces for solid oxide fuel cell (SOFC) was fabricated on NiO/yttria‐stabilized zirconia (YSZ) anode substrate by using dual‐sized YSZ powders without additional effort to roughen electrolyte film. The dual‐sized YSZ powders consisted of the fine YSZ powder and the coarse YSZ powder at different weight ratios. Incorporation of the coarse YSZ powder into the fine YSZ powder is in order to increase the surface roughness of electrolyte film, and the surface roughness obviously increased with the increase of coarse YSZ powder. The rough surfaces resulted in an enlargement of the electrochemical active area. It was found that electrode polarization was reduced evidently and cell electrochemical performance was enhanced, as the surface roughness increased. However, the excessive coarse YSZ powder was not beneficial for densification of electrolyte film and thus the open‐circuit voltage (OCV) was declined. The cell with 17 wt.% coarse YSZ powder in the electrolyte exhibited the best performance and the maximum power density was 1,930 mW cm^–2 at 800 °C.     

Comparison Between Anode‐Supported and Electrolyte‐Supported Ni‐CGO‐LSCF Micro‐tubular Solid Oxide Fuel Cells

Two types of micro‐tubular hollow fiber SOFCs (MT‐HF‐SOFCs) were prepared using phase inversion and sintering; electrolyte‐supported, based on highly asymmetric Ce_0.9Gd_0.1O_1.95(CGO) HFs and anode‐supported based on co‐extruded NiO‐CGO(CGO)/CGO HFs. Electroless plating was used to deposit Ni onto the inner surfaces of the electrolyte‐supported MT‐HF‐SOFCs to form Ni‐CGO anodes. LSCF‐CGO cathodes were deposited on the outer surface of both these MT‐HF‐SOFCs before their electrochemical performances were compared at similar operating conditions. The performance of the anode‐supported MT‐HF‐SOFCs which delivered ca. 480 mW cm^–2 at 600 °C was superior to the electrolyte‐supported MT‐HF‐SOFCs which delivered ca. six times lower power. The contribution of ohmic and electrode polarization losses of both FCs was investigated using electrochemical impedance spectroscopy. The electrolyte‐supported MT‐HF‐SOFCs had significantly higher ohmic and electrode polarization ASR values; this has been attributed to the thicker electrolyte and the difficulties associated with forming quality anodes inside the small (<1 mm) lumen of the electrolyte tubes. Further development on co‐extruded anode‐supported MT‐HF‐SOFCs led to the fabrication of a thinner electrolyte layer and improved electrode microstructures which delivered a world leading 2,400 mW cm^–2. The newly made cell was investigated at different H₂ flow rates and the effect of fuel utilization on current densities was analyzed.     

Direct Applicability of La0.6Sr0.4CoO3 – δ Thin Film Cathode to Yttria Stabilised Zirconia Electrolytes at T ≤ 650 °C

For investigating the direct applicability of highly active cobalt containing cathodes on YSZ electrolytes at a lower processing and operating temperature range (T ≤ 650 °C), we fabricated a thin film lanthanum strontium cobalt oxide (LSC) cathode on an yttria stabilised zirconia (YSZ)‐based solid oxide fuel cell (SOFC) via pulsed laser deposition (PLD). Its electrochemical performance (5.9 mW cm^–2 at 0.7 V, 650 °C) was significantly inferior to that (595 mW cm^–2 at 0.7 V, 650 °C) of an SOFC with a thin (t ∼ 200 nm) gadolinium doped ceria (GDC) buffer layer in between the LSC thin film cathode and the YSZ electrolyte. It implies that even though the cathode processing and cell operating temperatures were strictly controlled not to exceed 650 °C, the direct application of LSC on YSZ should be avoided. The origin of the cell performance deterioration is thoroughly studied by glancing angle X‐ray diffraction (GAXRD) and transmission electron microscopy (TEM), and the decomposition of the cathode and diffusion of La and Sr into YSZ were observed when LSC directly contacted YSZ.     

A Low Cost Large‐Area Solid Oxide Cells Fabrication Technology based on Aqueous Co‐Tape Casting and Co‐Sintering

Aqueous‐based tape casting is a low‐cost and environment friendly technology. In this paper, large‐area fuel electrode‐supported solid oxide cells (SOCs) were fabricated by this technology in conjunction with co‐sintering process. A 10 cm × 10 cm single cell with NiO/Zr_0.92Y_0.08O_2–δ fuel electrode, Zr_0.92Y_0.08O_2–δ electrolyte and La_0.6Sr_0.4Co_0.2Fe_0.8O_3+δ/Ce_0.9Gd_0.1O_2+δ air electrode has been successfully developed with improved electrode microstructure and hence the cell performance with the maximum power density of 534 mW cm^–2 at 850 °C with humidified H₂ as the fuel and air as the oxidant has been achieved. The optimal slurry formulations used in the fabrication of SOC were summarized for future reference purpose.     

Intermediate Temperature Anode‐Supported Fuel Cell Based on BaCe0.9Y0.1O3 Electrolyte with Novel Pr2NiO4 Cathode

A proton conducting ceramic fuel cell (PCFC) operating at intermediate temperature has been developed that incorporates electrolyte and electrode materials prepared by flash combustion (yttrium‐doped barium cerate) and auto‐ignition (praseodymium nickelate) methods. The fuel cell components were assembled using an anode‐support approach, with the anode and proton ceramic layers prepared by co‐pressing and co‐firing, and subsequent deposition of the cathode by screen‐printing onto the proton ceramic surface. When the fuel cell was fed with moist hydrogen and air, a high Open Circuit Voltage (OCV > 1.1 V) was observed at T > 550 °C, which was stable for 300 h (end of test), indicating excellent gas‐tightness of the proton ceramic layer. The power density of the fuel cell increased with temperature of operation, providing more than 130 mW cm^–2 at 650 °C. Symmetric cells incorporating Ni‐BCY10 cermet and BCY10 electrolyte on the one hand, and Pr₂NiO_{4 + δ} and BCY10 electrolyte on the other hand, were also characterised and area specific resistances of 0.06 Ω cm² for the anode material and 1–2 Ω cm² for the cathode material were obtained at 600 °C.     

Electrochemical Performance of a Ni and YSZ Composite Synthesised by Ultrasonic Spray Pyrolysis as an Anode for SOFCs

The electrochemical performance of an anode material for a solid oxide fuel cell (SOFC) depends highly on microstructure in addition to composition. In this study, a NiO–yttria‐stabilised zirconia (NiO–YSZ) composite with a highly dispersed microstructure and large pore volume/surface area has been synthesised by ultrasonic spray pyrolysis (USP) and its electrochemical characteristics has been investigated. For comparison, the electrochemical performance of a conventional NiO–YSZ is also evaluated. The power density of the zirconia electrolyte‐supported SOFC with the synthesised anode is ∼392 mW cm^–2 at 900 °C and that of the SOFC with the conventional NiO–YSZ anode is ∼315 mW cm^–2. The improvement is ∼24%. This result demonstrates that the synthesised NiO–YSZ is a potential alternative anode material for SOFCs fabricated with a zirconia solid electrolyte.     

Preparation and Electrochemical Properties of Sr‐doped K2NiF4‐type Cathode Material Pr1.7Sr0.3CuO4 for IT‐SOFCs

A novel K₂NiF₄‐type oxide Pr_1.7Sr_0.3CuO₄ (PSCu) is studied to obtain its electrochemical properties as the cathode for intermediate‐temperature solid oxide fuel cells (IT‐SOFCs). The PSCu cathode powder and Ce_0.8Sm_0.2O_1.9 (SDC) electrolyte powder were synthesized by sol‐gel method and glycine‐nitrate method, respectively. The crystal structure of PSCu powder and PSCu‐SDC composite powder were identified with X‐ray diffraction (XRD). It is shown that PSCu belongs to tetragonal K₂NiF₄‐type and has good chemical compatibility with SDC. The thermal expansion coefficient (TEC) of PSCu is close to that of SDC. The conductivity of PSCu tested with four‐probe method exhibits a semiconductor‐pseudometal transformation at 400–450 °C, where the maximum conductivity of 103.6 S cm⁻¹ is obtained. The polarization test indicates the area specific resistance (ASR) of PSCu decreases with increasing temperature, reaching 0.11 Ω cm² at 800 °C. The activation energy of oxygen reduction reaction during 600–800 °C is 1.19 eV. The single fuel cell performance test reveals the open circuit voltage (OCV) and resistivity of PSCu reduce with increasing temperature, but the power density ascends with increasing temperature. The maximal power density is 243 mW cm⁻² at 800 °C, and the corresponding current density and OCV are 633 mA cm⁻² and 0.77 V, respectively.     

Ionically Cross‐Linked Proton Conducting Membranes for Fuel Cells

For improving stability without sacrificing ionic conductivity, ionically cross‐linked proton conducting membranes are fabricated from Na⁺‐form sulfonated poly(phthalazinone ether sulfone kentone) (SPPESK) and H⁺‐formed sulfonated poly(2,6‐dimethyl‐1,4‐phenylene oxide) (SPPO). Ionically acid‐base cross‐linking between sulfonic acid groups in SPPO and phthalazone groups in SPPESK impart the composite membranes the good miscibility and electrochemical performance. In particular, the composite membranes possess proton conductivity of 60–110 mS cm⁻¹ at 30 °C. By controlling the protonation degree of SPPO within 40–100 %, the composite membranes with favorable cross‐linking degree are qualified for application in fuel cells. The maximum power density of the composite membrane reaches approximately 1100 mW cm⁻² at the current density of 2800 mA cm⁻² at 70 °C.