Co‐optimisation of the emitter region and the metal grid of silicon solar cells

The procedure for the simultaneous optimisation of the dopant density profile and the front metal grid of silicon solar cells is illustrated with representative cases of laboratory and commercial devices. Contour plots for the saturation current density and the photo‐generated current density of phosphorus doped emitter regions of silicon solar cells are calculated as a function of emitter thickness and dopant concentration, for the particular case of Gaussian dopant profiles. To expose the competing factors of surface and bulk emitter recombination, grid shading and series resistance, the other regions of the device are assumed ideal, that is, loss‐less. The calculated contour plots of the conversion efficiency indicate that relatively thick emitters are optimum if surface passivation is available, whereas thin, heavily doped emitters are preferable in the absence of surface passivation. Copyright © 2000 John Wiley & Sons, Ltd.     

Silicon solar cells based on all‐laser‐transferred contacts

Crystalline silicon solar cells based on all‐laser‐transferred contacts (ALTC) have been fabricated with both front and rear metallization achieved through laser induced forward transferring. Both the front and rear contacts were laser‐transferred from a glass slide coated with a metal layer to the silicon substrate already processed with emitter formation, surface passivation, and antireflection coating. Ohmic contacts were achieved after this laser transferring. The ALTC solar cells were fabricated on chemically textured p‐type Cz silicon wafers. An initial conversion efficiency of over 15% was achieved on a simple cell structure with full‐area emitter. Further improvements are expected with optimized laser transferring conditions, front grid pattern design, and surface passivation. The ALTC process demonstrates the advantage of laser processing in simplifying the solar cell fabrication by a one‐step metal transferring and firing process. Copyright © 2013 John Wiley & Sons, Ltd.     

Application of junction capacitance measurements to the characterization of solar cells

The quasi-static capacitance-voltage ( C-V) technique measures the dependence of junction capacitance on the bias voltage by applying a slow, reverse-bias voltage ramp to the solar cell in the dark, using simple circuitry. The resulting C-V curves contain information on the junction area and base dopant concentration, as well as their built-in potential. However, in the case of solar cells made on low to medium resistivity substrates and having thick emitters, the emitter dopant profile has to be taken into account. A simple method can then be used to model the complete C-V curves, which, if the base doping is known, permits one to estimate the emitter doping profile. To illustrate the method experimentally, several silicon solar cells with different base resistivities have been measured. They comprise a wide range of areas, surface faceting conditions and emitter doping profiles. The analysis of the quasi-static capacitance characteristics of the flat surface cells resulted in good agreement with independent data for the wafer resistivity and the emitter doping profile. The capacitance in the case of textured surfaces is a function of the effective junction area, which is otherwise difficult to measure, and is essential to understand the emitter and space charge region recombination currents. The results indicate that the effective area of the junction is not as large as the area of the textured surface.     

Selective laser ablation of SiNx layers on textured surfaces for low temperature front side metallizations

For an alternative front side metallization process without screen printing of metal paste the selective opening of the front surface anti‐reflection coating could be realized by laser ablation. A successful implementation of this scheme requires direct absorption of the laser light within the anti‐reflection coating, since the emitter underneath must not be damaged severely. Additionally, the ablation must be feasible on textured surfaces. In this paper, we show that laser light with a wavelength of 355 nm and a pulse length of approximately 30 ns is absorbed directly by a typical silicon nitride anti‐reflection coating. Based on lifetime measurements on ablated samples it is shown that a damage free laser ablation of SiN_x layers on planar surfaces is possible. The characteristic ablation structure on textured surfaces is explained and quantified by rigorous coupled wave analysis (RCWA) simulations. Finally, high efficiency solar cells with a standard emitter (R_sh approx. 50 Ω/sq) have been processed using laser ablation of the silicon nitride anti‐reflection coating. These cells show efficiencies of up to 19·1%, comparable to the reference solar cells using photolithographically opened contact areas. Copyright © 2008 John Wiley & Sons, Ltd.     

Add‐on laser tailored selective emitter solar cells

An elegant laser tailoring add‐on process for silicon solar cells, leading to selectively doped emitters increases their efficiency η by Δη = 0.5% absolute. Our patented, scanned laser doping add‐on process locally increases the doping under the front side metallization, thus allowing for shallow doping and less Auger recombination between the contacts. The selective laser add‐on process modifies the emitter profile from a shallow error‐function type to Gaussian type and enables excellent contact formation by screen printing, normally difficult to achieve for shallow diffused emitters. The significantly deeper doping profile of the laser irradiated samples widens the process window for the firing of screen printed contacts and avoids metal spiking through the pn‐junction. Copyright © 2010 John Wiley & Sons, Ltd.     

Opto‐electrical modelling and optimization study of a novel IBC c‐Si solar cell

Interdigitated back contact (IBC) crystalline silicon (c‐Si) solar cells are attracting a lot of attention because of their capability to reach world record conversion efficiency. Because of the relatively complex contact pattern, their design and optimization typically require advanced numerical simulation tools. In this work, a TCAD‐based simulation platform has been developed to account accurately and in detail the optical and passivation mechanisms of front texturization. Its validation has been carried out with respect to a novel homo‐junction IBC c‐Si solar cell based on ion implantation and epitaxial growth, comparing measured and simulated reflectance, transmittance, internal quantum efficiency, external quantum efficiency spectra, and current density–voltage characteristics. As a result of the calibration process, the opto‐electrical losses of the investigated device have been identified quantitatively and qualitatively. Then, an optimization study about the optimal front surface field (FSF) doping, front‐side texturing morphology, and rear side geometry has been performed. The proposed simulation platform can be potentially deployed to model other solar cell architectures than homo‐junction IBC devices (e.g., passivated emitter rear cell, passivated emitter rear locally diffused cell, hetero‐IBC cell). Simulation results show that a not‐smoothed pyramid‐textured front interface and an optimal FSF doping are mandatory to minimize both the optical and the recombination losses in the considered IBC cell and, consequently, to maximize the conversion efficiency. Similarly, it has been showed that recombination losses are affected more by the doping profile rather than the surface smoothing. Moreover, the performed investigation reveals that the optimal FSF doping is almost independent from the front texturing morphology and FSF passivation quality. According to this result, it has been demonstrated that an IBC cell featuring an optimal FSF doping does not exhibit a significant efficiency improvement when the FSF passivation quality strongly improves, proving that IBC cell designs based on low‐doped FSF require a very outstanding passivation quality to be competitive. Deploying an optimization algorithm, the adoption of an optimized rear side geometry can potentially lead to an efficiency improvement of about 1%_abs as compared with the reference IBC solar cell. Further, by improving both emitter and c‐Si bulk quality, a 22.84% efficient solar cell for 280‐μm thick c‐Si bulk was simulated. Copyright © 2017 John Wiley & Sons, Ltd.     

Passivation of n‐type emitter and p‐type base in solar cells via oxygen terminated silicon nanoparticles

Various measurements and experiments are performed to establish the mechanism of passivation on emitter and base of conventionally manufactured solar cell with p‐type base. The surface coatings on the emitter are removed. The bare surface is then coated with silicon (Si) nanoparticles (NPs) with oxygen termination. It shows an increase in the cell efficiency up to 14% over bare surface of solar cell. The NPs show enhancement in light scattering from the surface, but shows an increase in the recombination lifetime indicating an improved passivation. When back contact is partially removed, the coating on bare back side ( p‐type) of the solar cell also improves the cell efficiency. This is also attributable to the increased recombination lifetime from the measurements. Same NPs are seen to degrade the surface of n and p‐type Si wafers. This apparently contradictory behaviour is explained by studying and comparing the emitter (n‐type) surface of the solar cell with that of n‐type Si wafer and the back surface ( p‐type) with that of p‐type Si wafer. The emitter surface is distinctly different from the n‐type wafer because of the shallow p–n junction causing the surface depletion. Back surface has aluminium (Al) metal trace, which plays an important role in forming complexes with the oxygen‐terminated Si NPs (Si–O NPs). With these studies, it is observed that increase in the efficiency can potentially reduce the thermal budget in solar cell preparation. Copyright © 2013 John Wiley & Sons, Ltd.     

Optimizing the diffused regions of interdigitated backside buried contact solar cells

Recombination and a number of other important factors must be considered in the optimization of the diffused regions of high‐efficiency silicon solar cells. In this paper, we examine issues related to the four types of diffusions used in rear‐junction, interdigitated backside buried contact solar cells made on n‐type silicon wafers: the phosphorus‐diffused front‐surface field (FSF), the boron‐diffused emitter, and the boron and the phosphorus diffused contact regions. Dark saturation current density, effective lifetime, implied open‐circuit voltage and sheet resistance are characterized for the optimization of the above‐mentioned diffused regions. Diffusion uniformity and the avoidance of the diffusion‐induced dislocations are also discussed for the heavily diffused, metal coated contact diffusions. It is found that the optimal sheet resistances of the FSF for planar and textured surfaces are 120 Ω/□ and 105 Ω/□ respectively, whereas the optimal post‐processing sheet resistance for the boron emitter is approximately 100 Ω/□. Moreover, sheet resistance as heavy as 10–20 Ω/□ for the boron groove diffusion and 5–10 Ω/□ for the phosphorus groove diffusion have been achieved without introducing the diffusion‐induced misfit dislocations. Careful consideration of the issues discussed here led to an absolute efficiency improvement on the planar n‐type IBBC solar cell of more than 0·6%. Copyright © 2006 John Wiley & Sons, Ltd.     

Screen‐printed Emitter‐Wrap‐Through solar cell with single step side selective emitter with 18.8% efficiency

A fabrication process for Emitter‐Wrap‐Through solar cells on monocrystalline material with high quality gap passivation by wet thermal silicon dioxide is investigated. Masking and structuring steps are performed by screen‐printing technology. Via‐holes are created by an industrially applicable high‐speed laser drilling process. The cell structure features a selective emitter structure fabricated in a single high temperature step: a highly doped emitter at the via‐holes and the rear side, allowing for a low via‐hole resistivity as well as a low resistivity contact to screen‐printed pastes, and a moderately doped front side emitter exhibiting high quantum efficiency in the low wavelength range. Therefore a novel approach is applied depositing either doped or undoped PECVD silicon dioxide layers on the front side. It is shown that doping profiles advantageous for the EWT‐cell structure can be achieved. The screen‐printed aluminum paste is found to penetrate the underlying thermal dioxide layer at appropriate contact firing conditions leading to a zone of high recombination in the overlap region of aluminum and silicon dioxide. It is shown that conventional PECVD‐anti‐reflection silicon nitride acts as effective protection layer reducing the recombination in this region. Designated area conversion efficiencies up to 18.8% on FZ material are obtained applying the single step side selective emitter fabrication technique. Copyright © 2010 John Wiley & Sons, Ltd.     

Analysis of the EWT‐DGB solar cell at low and medium concentration and comparison with a PESC architecture

Silicon represents an interesting material to fabricate low‐cost and relatively simple and high‐efficient solar cells in the low and medium concentration range. In this paper, we discuss a novel cell scheme conceived for concentrating photovoltaic, named emitter wrap through with deep grooved base (EWT‐DGB), and compare it with the simpler passivated emitter solar cell. Both cells have been fabricated by means of a complementary metal–oxide–semiconductor‐compatible process in our laboratory. The experimental characterization of both cells is reported in the range 1–200 suns in terms of conversion efficiency, open circuit voltage, short circuit current density and fill factor. In particular, for the EWT‐DGB solar cells, we obtain an encouraging 21.4% maximum conversion efficiency at 44 suns. By using a calibrated finite‐element numerical electro‐optical simulation tool, validated by a comparison with experimental data, we study the potentials of the two architectures for concentrated light conditions considering possible realistic improvements with respect to the fabricated devices. We compare the solar cell figures of merit with those of the state‐of‐the‐art silicon back‐contact back‐junction solar cell holding the conversion efficiency record for concentrator photovoltaic silicon. Simulation results predict a 24.8% efficiency at 50 suns for the EWT‐DGB cell and up to 23.9% at 100 suns for the passivated emitter solar cell, thus confirming the good potential of the proposed architectures for low to medium light concentration. Finally, simulations are exploited to provide additional analysis of the EWT‐DGB scheme under concentrated light. Copyright © 2017 John Wiley & Sons, Ltd.     

Combining laser chemical processing and aerosol jet printing: a laboratory scale feasibility study

First results showing the viability of combining laser chemical processing (LCP) and aerosol jet printing (AJP) technologies to produce a high‐efficiency front side for silicon solar cells are presented. LCP simultaneously opens the anti‐reflection coating (ARC) and highly dopes the underlying silicon to create a selective emitter, while AJP is the first in a two‐step fine‐line contact formation procedure. The electrical properties as well as the morphology of the resulting structures are presented. Performance similar to that achieved with evaporated TiPdAg metallization is demonstrated. Copyright © 2010 John Wiley & Sons, Ltd.     

丝网印刷制备黑硅太阳电池及其性能表征

采用纳米金颗粒催化腐蚀的方法在硅片表面制备得纳米多孔结构,实现了1.5%（300-1200 nm）的权重反射率。本文采用OPCl3扩散、丝网印刷制备前后电极及共烧等常规太阳电池工艺来制备黑硅太阳电池,对不同腐蚀深度及不同扩散方阻的黑硅太阳电池片的输出电性能进行了分析,并对制备工艺进行了优化,提高了电池的转换效率,实现了丝网印刷制备12.17%的黑硅太阳电池转换效率。     

Optimization of ultraviolet laser doping for crystalline silicon solar cells with a novel segmented selective emitter design

This paper reports on the use of ultraviolet laser for forming segmented selective emitters on POCl ₃ n ⁺ –p–p ⁺ solar cells. Laser scan speed, pulse power, and repetition rate are optimized to minimize laser‐induced defects, which are found to enhance recombination and reduce the local open‐circuit voltage. Laser‐doped selective emitters formed by locally driving in additional phosphorous from the diffusion glass are well suited for an etchback process without the need for a mask. In this paper, we show a novel selective emitter design that is segmented instead of continuous, combined with an emitter etchback process gives an efficiency improvement of about 0.3% absolute over a standard industrial type solar cell and 0.2% absolute improvement over a non‐segmented selective emitter solar cell. Copyright © 2012 John Wiley & Sons, Ltd.     

Diffusion‐based model of local Al back surface field formation for industrial passivated emitter and rear cell solar cells

In this work, the back surface field (BSF) formation of locally alloyed Al‐paste contacts employed in recent industrial passivated emitter and rear cell solar cell designs is discussed. A predictive model for resulting local BSF thickness and doping profile is proposed that is based on the time‐dependent Si distribution in the molten Al paste during the firing step. Diffusion of Si in liquid Al away from the contact points is identified as the main differentiator to a full‐area Al‐BSF; therefore, a diffusion‐based solution to the involved differential equation is pursued. Data on the Si distribution in the Al and the resulting BSF structures are experimentally obtained by firing samples with different metal contact geometries, peak temperature times and pastes as well as by investigating them by means of scanning electron microscopy and energy dispersive X‐ray spectroscopy. The Si diffusivity in the Al paste is then calculated from these results. It is found that the diffusivity is strongly dependent on the paste composition. Furthermore, the local BSF doping profiles and thicknesses resulting from different contact geometries and paste parameters are calculated from the Si concentration at the contact sites, the diffusivity and solubility data. These profiles are then used in a finite element device simulator to evaluate their performance on solar cell level. With this approach, a beneficial paste composition for any given rear contact geometry can be determined. Two line widths are investigated, and the effects of the different paste properties are discussed in the light of the solar cell results obtained by simulation. Copyright © 2013 John Wiley & Sons, Ltd.     

Autodiffusion: a novel method for emitter formation in crystalline silicon thin‐film solar cells

The in situ formation of an emitter in monocrystalline silicon thin‐film solar cells by solid‐state diffusion of dopants from the growth substrate during epitaxy is demonstrated. This approach, that we denote autodiffusion, combines the epitaxy and the diffusion into one single process. Layer‐transfer with porous silicon (PSI process) is used to fabricate n‐type silicon thin‐film solar cells. The cells feature a boron emitter on the cell rear side that is formed by autodiffusion. The sheet resistance of this autodiffused emitter is 330 Ω/□. An independently confirmed conversion efficiency of (14·5 ± 0·4)% with a high short circuit current density of (33·3 ± 0·8) mA/cm² is achieved for a 2 × 2 cm² large cell with a thickness of (24 ± 1) µm. Transferred n‐type silicon thin films made from the same run as the cells show effective carrier lifetimes exceeding 13 µs. From these samples a bulk diffusion length L > 111 µm is deduced. Amorphous silicon is used to passivate the rear surface of these samples after the layer‐transfer resulting in a surface recombination velocity lower than 38 cm/s. Copyright © 2006 John Wiley & Sons, Ltd.     

Optimizing annealing steps for crystalline silicon solar cells with screen printed front side metallization and an oxide‐passivated rear surface with local contacts

Silicon solar cells that feature screen printed front contacts and a passivated rear surface with local contacts allow higher efficiencies compared to present industrial solar cells that exhibit a full area rear side metallization. If thermal oxidation is used for the rear surface passivation, the final annealing step in the processing sequence is crucial. On the one hand, this post‐metallization annealing (PMA) step is required for decreasing the surface recombination velocity (SRV) at the aluminum‐coated oxide‐passivated rear surface. On the other hand, PMA can negatively affect the screen printed front side metallization leading to a lower fill factor. This work separately analyzes the impact of PMA on both, the screen printed front metallization and the oxide‐passivated rear surface. Measuring dark and illuminated IV‐curves of standard industrial aluminum back surface field (Al‐BSF) silicon solar cells reveals the impact of PMA on the front metallization, while measuring the effective minority carrier lifetime of symmetric lifetime samples provides information about the rear side SRV. One‐dimensional simulations are used for predicting the cell performance according to the contributions from both, the front metallization and the rear oxide‐passivation for different PMA temperatures and durations. The simulation also includes recombination at the local rear contacts. An optimized PMA process is presented according to the simulations and is experimentally verified. The optimized process is applied to silicon solar cells with a screen printed front side metallization and an oxide‐passivated rear surface. Efficiencies up to 18.1% are achieved on 148.8 cm² Czochralski (Cz) silicon wafers. Copyright © 2009 John Wiley & Sons, Ltd.     

>16% thin‐film epitaxial silicon solar cells on 70‐cm2 area with 30‐µm active layer,porous silicon back reflector,and Cu‐based top‐contact metallization

We demonstrate the use of a copper‐based metallization scheme for the specific application of thin‐film epitaxial silicon wafer equivalent (EpiWE) solar cells with rear chemical vapor deposition emitter and conventional POCl₃ emitter. Thin‐film epitaxial silicon wafer equivalent cells are consisting of high‐quality epitaxial active layer of only 30 µm, beneath which a highly reflective porous silicon multilayer stack is embedded. By combining Cu‐plating metallization and narrow finger lines with an epitaxial cell architecture including the porous silicon reflector, a J_sc exceeding 32 mA/cm² was achieved. We report on reproducible cell efficiencies of >16% on >70‐cm² cells with rear epitaxial chemical vapor deposition emitters and Cu contacts. Copyright © 2011 John Wiley & Sons, Ltd.     

Use of porous silicon antireflection coating in multicrystallinesilicon solar cell processing

The latest results on the use of porous silicon (PS) as an antireflection coating (ARC) in simplified processing for multicrystalline silicon solar cells are presented. The optimization of a PS selective emitter formation results in a 14.1% efficiency multicrystalline (5×5 cm²) Si cell with evaporated contacts processed without texturization, surface passivation, or additional ARC deposition. Specific attention is given to the implementation of a PS ARC into an industrially compatible screen-printed solar cell process. Both the chemical and electrochemical PS ARC formation method are used in different solar cell processes, as well as on different multicrystalline silicon materials. Efficiencies between 12.1 and 13.2% are achieved on large-area (up to 164 cm² ) commercial Si solar cells     

Highly transparent modulated surface textured front electrodes for high‐efficiency multijunction thin‐film silicon solar cells

To further increase the efficiency of multijunction thin‐film silicon (TF‐Si) solar cells, it is crucial for the front electrode to have a good transparency and conduction, to provide efficient light trapping for each subcell, and to ensure a suitable morphology for the growth of high‐quality silicon layers. Here, we present the implementation of highly transparent modulated surface textured (MST) front electrodes as light‐trapping structures in multijunction TF‐Si solar cells. The MST substrates comprise a micro‐textured glass, a thin layer of hydrogenated indium oxide (IOH), and a sub‐micron nano‐textured ZnO layer grown by low‐pressure chemical vapor deposition (LPCVD ZnO). The bilayer IOH/LPCVD ZnO stack guarantees efficient light in‐coupling and light trapping for the top amorphous silicon (a‐Si:H) solar cell while minimizing the parasitic absorption losses. The crater‐shaped micro‐textured glass provides both efficient light trapping in the red and infrared wavelength range and a suitable morphology for the growth of high‐quality nanocrystalline silicon (nc‐Si:H) layers. Thanks to the efficient light trapping for the individual subcells and suitable morphology for the growth of high‐quality silicon layers, multijunction solar cells deposited on MST substrates have a higher efficiency than those on single‐textured state‐of‐the‐art LPCVD ZnO substrates. Efficiencies of 14.8% (initial) and 12.5% (stable) have been achieved for a‐Si:H/nc‐Si:H tandem solar cells with the MST front electrode, surpassing efficiencies obtained on state‐of‐the‐art LPCVD ZnO, thereby highlighting the high potential of MST front electrodes for high‐efficiency multijunction solar cells. Copyright © 2015 John Wiley & Sons, Ltd.