聚砜/改性碳纳米管复合膜的制备及亲水性能

利用浸没沉淀相转化法,以聚砜(PSF)为膜材料,羧基化碳纳米管(MWCNTs-COOH)为添加剂,聚乙烯吡咯烷酮(PVP)为致孔剂,N,N-二甲基乙酰胺(DMAc)为溶剂,制备了聚砜/多壁碳纳米管复合膜,系统研究了制备复合膜时碳纳米管的添加量、预挥发时间以及凝固浴组成对其结构和性能的影响。实验结果表明,添加MWCNTs-COOH后,复合膜的亲水性能和抗污性能显著提高,同时复合膜的力学性能也明显增强。复合膜的 SEM 照片显示,随预挥发时间的延长和凝固浴中DMAc 质量分数的增加,复合膜断面由指状孔结构向海绵状孔结构过渡;复合膜的水通量下降,截留率上升。     

改性多壁碳纳米管／PA6纤维的制备及力学性能

将多壁碳纳米管(MWNT)氧化后,酰氯化处理,在氨基封端的PA6聚合时加入,制备PA6／MWNT母粒,将母粒同PA6切片熔融共混纺丝,制备PA6／MWNT纤维。用INSTRON 1122型万能材料试验机测定纤维的力学性能。结果表明,改性MWNT的加入提高了PA6纤维的断裂强度,纤维中MWNT质量分数仅为0．05％时,纤维的断裂强度和初始模量最大,分别增加了60％和86％。用扫描电镜观察复合纤维的结构,发现MWNT均匀地分布在PA6中,并与PA6基体间有相互作用,沿纤维轴向取向。     

Thermal and mechanical properties of phosphorylated multiwalled carbon nanotube/polyvinyl chloride composites

The fabrication of carbon nanotube/polyvinyl chloride (PVC) composites and a study of their thermal and mechanical properties are reported. Phosphorylated multiwalled carbon nanotube (p-MWCNT) and pristine MWCNT were used. The MWCNT were embedded in the polymer matrix through melt mixing. The phosphorylation of the MWCNT and their dispersion in the PVC matrix were characterized by scanning and transmission electron microscopy and Raman spectroscopy. Thermal analysis by thermal gravimetric analysis and differential scanning calorimetry, showed an increase in glass transition temperature and melting temperature for the composites with respect to pure PVC. The modulus of the MWCNT/PVC composites increased while there was a reduction in their tensile strength, indicating a decrease in polymer toughness.     

Synthesis and mechanical properties of carbon nanotube/diamond-like carbon composite films

Diamond-like carbon (DLC) coatings were successfully deposited on carbon nanotube (CNT) films with CNT densities of 1 × 10⁹/cm², 3 × 10⁹/cm², and 7 × 10⁹/cm² by a radio frequency plasma-enhanced chemical vapor deposition (CVD). The new composite films consisting of CNT/DLC were synthesized to improve the mechanical properties of DLC coatings especially for toughness. To compare those of the CNT/DLC composite films, the deposition of a DLC coating on a silicon oxide substrate was also carried out. A dynamic ultra micro hardness tester and a ball-on-disk type friction tester were used to investigate the mechanical properties of the CNT/DLC composite films. A scanning electron microscopic (SEM) image of the indentation region of the CNT/DLC composite film showed a triangle shape of the indenter, however, chippings of the DLC coating were observed in the indentation region. This result suggests the improvement of the toughness of the CNT/DLC composite films. The elastic modulus and dynamic hardness of the CNT/DLC composite films decreased linearly with the increase of their CNT density. Friction coefficients of all the CNT/DLC composite films were close to that of the DLC coating.     

Cellulose acetate/multiwalled carbon nanotube nanocomposites with improved mechanical,thermal, and electrical properties

Cellulose acetate (CA)‐based nanocomposites with various contents of neat multiwalled carbon nanotube (MWCNT) or acid‐treated one (MWCNT‐COOH) are prepared via melt‐compounding method and investigated their morphology, thermal stability, mechanical, and electrical properties. SEM microphotographs reveal that MWCNT‐COOHs are dispersed uniformly in the CA matrix, compared with neat MWCNTs. FTIR spectra support that there exists a specific interaction between carboxyl groups of MWCNT‐COOHs and ester groups of CA, indicating good interfacial adhesion between MWCNT‐COOHs and CA matrix. Accordingly, thermal stability and dynamic mechanical properties of CA/MWCNT‐COOH nanocomposites were higher than those of CA/MWCNT composites. On the contrary, electrical volume resistivities of CA/MWCNT‐COOH nanocomposites are found to be somewhat higher than those of CA/MWCNT composites, which is because of the deterioration of graphene structures for MWCNT‐COOHs and the good dispersion of MWCNT‐COOHs in the CA matrix. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Conductivity and mechanical properties of well-dispersed single-wall carbon nanotube/polystyrene composite

The morphologies, electrical and mechanical properties and structure of polystyrene (PS) composites with varying concentrations of single-wall carbon nanotubes (SWNT) are analyzed. Using Raman spectroscopy and electron microscopy, we demonstrate that initial thermal annealing of SWNT significantly improves their dispersion in PS. In dielectric measurements, the annealed SWNT/PS composites show higher electrical conductivity and a lower percolation threshold (less than 0.3 wt%) than the raw SWNT/PS composites, which provides further evidence of good dispersion of the annealed SWNT in PS. Raman spectra of composites under tension show good transfer of an applied stress from the polymer matrix to SWNT. However, mechanical moduli of the annealed SWNT/PS composites are only increased slightly. The reason for this discrepancy remains unclear.     

Electrical,mechanical, and crystallization properties of ethylene‐tetrafluoroethylene copolymer/multiwalled carbon nanotube composites

Multiwalled carbon nanotubes (MWCNTs) were melt‐mixed in a conical twin‐screw extruder with a random copolymer of ethylene and tetrafluoroethylene. Surprisingly, the electrical percolation threshold of the resultant composites was quite low; ～0.9 wt %. In fact, this value is as low or lower than the value for most MWCNT/semicrystalline polymer composites made with roughly equivalent aspect ratio tubes mixed in a similar manner, for example, melt mixing. This low percolation threshold, suggestive of good dispersion, occurred even though the polymer surface energy is quite low which should make tubes more difficult to disperse. Dynamic mechanical measurements confirmed the rather low percolation threshold. The effect of nanotubes on crystallization kinetics was quite small; suggesting perhaps that a lack of nucleation which in turn reduces/eliminates an insulating crystalline polymer layer around the nanotubes might explain the low percolation threshold. Finally, the modulus increased with the addition of nanotubes and the strain at break decreased. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 41052.     

Preparation and properties of multiwalled carbon nanotube/polycaprolactone nanocomposites

Multiwalled carbon nanotube/polycaprolactone nanocomposites (MWNT/PCL) were prepared by in situ polymerization, whereby as‐received MWNTs (P‐MWNTs) and purified MWNTs (A‐MWNTs) were used as reinforcing materials. The A‐MWNTs were purified by nitric acid treatment, which introduced the carboxyl groups (COOH) on the MWNT. The micrographs of the fractured surfaces of the nanocomposites showed that the A‐MWNTs in A‐MWNT/PCL were better dispersed than P‐MWNTs in PCL matrix (P‐MWNT/PCL). Percolation thresholds of the P‐MWNT/PCL and A‐MWNT/PCL, which were studied by rheological properties, were found at ～2 wt % of the MWNT. The conductivity of the P‐MWNT/PCL was between 10^?1 and 10^?2 S/cm by loading of 2 wt % of MWNT although that of the A‐MWNT/PCL reached ～10^?2 S/cm by loading of 7 wt % of MWNT. The conductivity of the P‐MWNT/PCL was higher than that of the A‐MWNT/PCL at the entire range of the studied MWNT loading, which might be due to the destruction of π‐network of the MWNT by acid treatment, although the A‐MWNT/PCL was better dispersed than the P‐MWNT/PCL. The amount of the MWNT at which the conductivity of the nanocomposite started to increase was strongly correlated with the percolation threshold. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 1957–1963, 2007     

Thermal and mechanical properties of carbon nanotube/epoxy nanocomposites reinforced with pristine and functionalized multiwalled carbon nanotubes

In this study, the effects of functionalization and weight fraction of mutliwalled carbon nanotubes (CNTs) were investigated on mechanical and thermomechanical properties of CNT/Epoxy composite. Epoxy resin was used as matrix material with pristine‐, COOH‐, and NH₂‐functionalized CNTs as reinforcements in weight fractions of 0.1, 0.5, and 1.0%. Varying (increasing) the weight fraction and changing type (pristine or functionalized) of CNTs caused increment in Young's modulus and tensile strength as observed during mechanical tests. CNT reinforcement improved thermal stability of the nanocomposites as observed by thermogravimetric analysis. Thermomechanical analysis showed a slight reduction in free volume of the polymer, that is a drop in coefficient of thermal expansion, prior to glass transition temperature (T_g) beside a slight increase in T_g value. Dynamic mechanical analysis indicated an increase in storage modulus and T_g owing to the strength addition of CNT to the matrix alongside the hardener. Scanning electron microscopy analysis of the fractured surface(s) revealed that CNTs were well dispersed with no agglomeration and resulted in reinforcing the matrix. POLYM. COMPOS., 36:1891–1898, 2015. © 2014 Society of Plastics Engineers     

Thermoplastic polyvinyl alcohol/multiwalled carbon nanotube composites: Preparation,mechanical properties,thermal properties,and electromagnetic shielding effectiveness

This study uses the solution mixing method to combine plasticized polyvinyl alcohol (PVA) as a matrix, and multiwalled carbon nanotubes (MWCNTs) as reinforcement to form PVA/MWCNTs films. The films are then laminated and hot pressed to create PVA/MWCNTs composites. The control group of PVA/MWCNTs composites is made by incorporating the melt compounding method. Diverse properties of PVA/MWCNTs composites are then evaluated. For the experimental group, the incorporation of MWCNTs improves the glass transition temperature (T_g), crystallization temperature, T_c), and thermal stability of the composites. In addition, the test results indicate that composites containing 1.5 wt % of MWCNTs have the maximum tensile strength of 51.1 MPa, whereas composites containing 2 wt % MWCNTs have the optimal electrical conductivity of 2.4 S/cm, and electromagnetic shielding effectiveness (EMI SE) of ?31.41 dB. This study proves that the solution mixing method outperforms the melt compounding method in terms of mechanical properties, dispersion, melting and crystallization behaviors, thermal stability, and EMI SE. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43474.     

The thermal and mechanical properties of a polyurethane/multi-walled carbon nanotube composite

A polyurethane/multi-walled carbon nanotube elastomer composite was synthesized. The microstructure of the composite was examined by field-emission scanning electron microscopy and transmission electron microscopy. The thermal and mechanical properties of the composite were characterized by dynamic mechanical thermal analysis, thermogravimetric analysis and tensile testing. The chemical linkage of carbon nanotubes with polyurethane matrix was confirmed by Fourier transform infrared spectra. The study on the structure of the composite showed that carbon nanotubes could be dispersed in the polymer matrix well apart from a few of clusters. The results from thermal analysis indicated that the glass transition temperature of the composite was increased by about 10 °C and its thermal stability was obviously improved, in comparison with pure polyurethane. The investigation on the mechanical properties showed that the modulus and tensile strength could be obviously increased by adding 2 wt% (by weight) CNT to the matrix.     

Broadband dielectric properties of multiwalled carbon nanotube/polystyrene composites

This study investigates the dielectric properties of multiwalled carbon nanotube (MWCNT)/polystyrene (PS) composites over the broadband frequency range, i.e., 10^?1 to 10⁶ Hz. The results showed that the real permittivity and imaginary permittivity increased remarkably with increased MWCNT concentration. For instance, at 100 Hz, the real permittivity and imaginary permittivity of the pristine PS was 2.71 and 0.01, respectively, which increased to 5.22 × 10⁴ and 3.28 × 10⁷ at 3.50 wt%, respectively. The increase in the real permittivity was related to the formation of a large number of nanocapacitor structures, i.e., MWCNTs as nanoelectrodes and polymer matrix as dielectric material, i.e., interfacial polarization. The increase in the imaginary permittivity with MWCNT loading was attributed greater number of dissipating charges, enhanced conductive network formation, and boosted polarization loss arising from interfacial polarization. It was also observed that the real and imaginary permittivities were frequency independent in the insulative region, whereas they decreased drastically with frequency in the conductive region. The descending trend of real permittivity with frequency in the conductive region was related to charge polarization relaxation, whereas the reduction in imaginary permittivity with frequency was attributed to lower Ohmic loss and polarization loss. POLYM. ENG. SCI., 55:173–179, 2015. © 2014 Society of Plastics Engineers     

Preparation and thermal properties of multiwalled carbon nanotube/polybenzoxazine nanocomposites

In this study, we prepared nanocomposites comprising multiwalled carbon nanotubes (MWCNTs) and polybenzoxazine (PBZ). The MWCNTs were purified through microwave digestion to remove most of the amorphous carbon and metal impurities. After purification, MWCNTs were treated with H₂SO₄/HNO₃ (3 : 1) to introduce hydroxyl and carboxyl groups onto their surfaces. Raman spectroscopy revealed the percentage of nanotube content improved after prolonged microwave treatment, as evidenced by the decrease in the ratio of the D (1328 cm^?1) and G (1583 cm^?1) bands. For the untreated MWCNTs, the I_D/I_G ratio was 0.56. After microwave treatment for 40 min, the value decreased to 0.29, indicating that the percentage of nanotube content improved. Dynamic mechanical analyses (DMAs) revealed that the storage moduli and the T_gs of the MWCNTs/PBZ nanocomposites were higher than that of the pristine PBZ. This is due to the nanometer‐scale MWCNTs restricting the motion of the macromolecular chains in the nanocomposites. Transmission electron microscopy (TEM) image revealed that the MWCNTs were well dispersed within the PBZ matrix on the nanoscale when the MWCNT content was less than 2.0 phr. The coefficient of thermal expansion (CTE) of the nanocomposites decreased on increasing the MWCNTs content. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Polyurethane/amino‐grafted multiwalled carbon nanotube nanocomposites: Microstructure,thermal, mechanical,and rheological properties

A mixture of two different polyols, (polytetramethylene ether glycol and polydimethylsiloxane), were employed to synthesize a new structure of polyurethane (PU) with methylene diphenyl diisocyanate (MDI) and 1,4‐butanediol as chain extender. PU nanocomposites containing variable amount (0.3, 0.5, 1, and 3 wt %) of amino‐grafted multiwalled carbon nanotubes (NH₂‐MWNT) were prepared via in situ polymerization. The dispersion of NH₂‐MWNT into polymer matrix was investigated by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). Fourier transform infrared spectroscopy (FT‐IR) confirmed the urethane‐urea chemical bonding between the PU chains and the NH₂‐MWNT. Thermal stabilities of the nanocomposites were examined with thermogravimetric analysis (TGA) and the results indicated a remarkable improvement with increasing NH₂‐MWNT contents. The results of dynamic mechanical thermal analysis (DMTA) including storage modulus (E′) and glass transition temperature (T_g), as well as tensile properties demonstrated that the yield strength, strain‐at‐break, and young modulus were enhanced by increasing NH₂‐MWNT content. Rheological behavior including complex viscosity and storage and loss moduli of the PU nanocomposites improved with increasing NH₂‐MWNT loading, as well. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44411.     

Field emission properties of Cu/multiwalled carbon nanotube composite films fabricated by an electrodeposition technique

Composite films of Cu and multiwalled carbon nanotubes (MWCNTs) were fabricated by an electrodeposition technique, and their field emission properties were examined. Commercially available MWCNTs with various diameters (60–150 nm) were used. The microstructure of the composite films was analyzed by scanning electron microscopy and the field emission properties were measured using a diode-type system. Cu/MWCNT composite films with homogeneous dispersion of MWCNTs were fabricated using each type of MWCNT. Bare MWCNTs were present on the surface of the composite films and the ends of the protruding tips were fixed by the deposited copper matrix. The composite films produced clear emission currents and the corresponding Fowler–Nordheim (F–N) plots showed that these were field emission currents. The turn-on electric field tended to decrease with decreasing MWCNT diameter. A light-emitting device incorporating the Cu/MWCNT composite film as a field emitter was fabricated, and its light-emitting properties were investigated. Light emission with a brightness of around 100 cd m^?2 was observed for approximately 100 h.     

Electromagnetic interference shielding of cellulose triacetate/multiwalled carbon nanotube composite films

Cellulose triacetate (CTA) and multiwalled carbon nanotube (MWNT) composite films were prepared by dispersing different weight percentages of MWNTs into a CTA solution. These composite blends were characterized by UV–vis spectroscopy (UV), and their surface mophology, thermal stability, and amended crystallinity were determined by atomic force microscopy (AFM), thermogravimetric analysis (TGA), and X‐ray diffraction (XRD), respectively. Measurements of the complex impedance of the composite samples were made in the form of films. Sheets prepared from conventional techniques were used to study microwave absorption in the microwave range of 2–12 GHz, and the effects of sample thickness on microwave absorption were investigated. The experimental results show that the electrical conductivity of composites increases with the increase in MWNT loading without a percolation threshold. POLYM. COMPOS., 2011. © 2011 Society of Plastics Engineers     

Preparation of polyaniline/multiwalled carbon nanotube composite by novel electrophoretic route

A nano-structured composite film comprising of emeraldine salt (ES) and carboxyl group functionalized multiwalled carbon nanotubes (MWCNT-c) has been electrophoretically prepared from their colloidal suspension on an indium-tin-oxide (ITO) coated glass plate. This nano-structured composite film (ES/MWCNT-c) has been characterized using atomic force microscopy (AFM), ultraviolet-visible (UV-visible) spectroscopy, Fourier transform infrared (FT-IR) spectroscopy, cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The AFM studies reveal porous morphology with uniformly distributed MWCNT-c in this composite film. The SEM and TEM investigations reveal wrapping of MWCNT-c with the chains of ES. UV-visible and FT-IR investigations show the formation of MWCNT-c doped composite at the molecular level. The results of the CV and EIS studies indicate enhanced electrochemical and charge transfer behavior of the composite. The application of ES/MWCNT-c/ITO electrode to biosensor for cholesterol indicates short response time (10 s) and high sensitivity (6800 nA mM⁻¹).     

Mechanical and thermal properties of polyphenylene sulfide/multiwalled carbon nanotube composites

Polyphenylene sulfide (PPS)/multiwalled carbon nanotube (MWCNT) composites were prepared using a melt‐blending procedure combining twin‐screw extrusion with centrifugal premixing. A homogeneous dispersion of MWCNTs throughout the matrix was revealed by scanning electron microscopy for the nanocomposites with MWCNT contents ranging from 0.5 to 8.0 wt %. The mechanical properties of PPS were markedly enhanced by the incorporation of MWCNTs. Halpin‐Tsai equations, modified with an efficiency factor, were used to model the elastic properties of the nanocomposites. The calculated modulus showed good agreement with the experimental data. The presence of the MWCNTs exhibited both promotion and retardation effects on the crystallization of PPS. The competition between these two effects results in an unusual change of the degree of crystallinity with increasing MWCNT content. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Improvement of the mechanical properties of single-walled carbon nanotube networks by carbon plasma coatings

Carbon vacuum arc was used to deposit 5–25 nm thick carbon coatings on single-walled carbon nanotube (SWCNT) networks. The SWCNT bundles thus embedded in conformal coatings maintained their optical transparency and electrical conductivity. Sheet resistances of the networks were measured during the vacuum arc deposition, revealing initially a 100-fold increase, followed by significant recovery after exposing the samples to an ambient atmosphere. Nanoindentation measurements revealed improved elasticity of the network after applying the carbon coating. Pristine SWCNT networks were easily deformed permanently, but a 20 nm carbon coating strengthened the nanostructure, resulting in a fully elastic recovery from a 20 μN load applied with a Berkovich tip. In nano-wear tests on selected areas, the coated SWCNT maintained its networking integrity after two passes raster scan at loads up to 25 μN. On the other hand, the pristine networks were badly damaged under a 10 μN scan load and completely displaced under 25 μN. Raman and electron energy loss spectroscopies indicated the carbon coating on bundles to be mainly sp² bonded. Finite element modeling suggests that the low content of sp³ bonds may be due to heating by the intense ion flux during the plasma pulse.