共查询到20条相似文献,搜索用时 602 毫秒
1.
2.
3.
4.
5.
6.
连续挤压与正挤压在扩展成形中的对比分析 总被引:2,自引:0,他引:2
通过有限元数值模拟分析了连续挤压较常规正挤压更能实现铜的更大扩展比挤压的原理。在连续挤压扩展模型的基础上建立了与之相对应的常规正挤压模型,对两种模型下金属的流动特性进行了对比分析。连续挤压与正挤压相比,由于在挤压轮槽区,受到挤压轮三面的主动摩擦力和腔体一面阻碍摩擦力的作用,有利于提高铜扩展成形金属流动的均匀性;而正挤压中坯料在挤压筒区受四面的摩擦阻力的作用,加剧了金属流动的不均匀性。所以,连续挤压中的扩展成形金属在产品宽度和厚度方向上流动较正挤压更均匀,成形产品的完整性更好。因此,连续挤压更利于铜的扩展成形。 相似文献
7.
介绍了采用有效摩擦力进行挤压的基本概念,这是俄罗斯三个研究机构的科学家们长期工作的结果。此处所述的是利用铸锭和挤压筒之间的摩擦以加强反向挤压过程。 相似文献
8.
9.
10.
针对空心导杆零件的特点,分析了其挤压成形工艺,提出了该零件的挤压成形工艺方案,并利用数值模拟软件DEFORM-2D,分析了金属成形时的流动规律.通过改变摩擦因子和芯轴运动速度,进行了多次模拟,得到了空心导杆在挤压成形时的最优工艺参数,并分析了在最优工艺参数下,空心导杆挤压成形时的最大等效应力、损伤因子、最大成形载荷和芯轴的受力,从而保证了挤压件的质量,为实际生产提供了理论基础. 相似文献
11.
对挤压铝合金时锭坯与工模具接触面上摩擦的性质和行为进行了研究。结果表明,由于铝锭坯与粘附在挤压筒内壁、穿孔针和模具工作带上的铝套或铝层是同种金属,粘着变形使得接触表面微结构自发地趋于相称,从而导致很大的摩擦;其摩擦因数与铝合金的牌号和变形抗力有关。建立了摩擦因数与变形抗力的关系式。 相似文献
12.
邓小民 《中国有色金属学报》2002,12(3):539-543
目前,用于计算反向挤压力的计算式都是根据相奕正向挤压时的算式,并直接令作用在挤压筒壁上的摩擦为零得来的。实践中发现,计算出的挤压力与实测值差异较大,无法正确指导生产。造成这种差异的主要原因是忽略了正、反向挤压时变形区中温升及加工硬化程度不同对金属变形抗力的影响。及采用了与正挤压时盯同的变形抗力值。通过实践,建立了确定反挤压时金属变形抗力的方法及计算式。验证结果表明,以此为依据计算反向挤压力,误差不大于5%,可以满足工程计算要求。 相似文献
13.
针对44 mm×10.5 mm小规格Ti Ni Nb管材反挤压成形试验的工艺参数确定和模具设计问题,采用有限元热力耦合数值模拟和单因素轮换法,分析在满足制件成形质量(挤出温度低于共晶熔点)的前提下,挤压力与凹模模角和定径带长度、凹模和挤压筒温度、毛坯初始温度、挤压速度及摩擦因子等工艺参数和模具结构参数之间的关系,确定影响挤压力的主要工艺参数和模具结构参数分别为凹模模角、初始坯料温度、挤压速度和摩擦因子,并给出上述参数的取值范围。通过基于数值模拟的正交试验方法,得到了主要工艺参数和模具结构参数的最佳组合,即在保证润滑效果的前提下,取凹模模角110°、毛坯初始温度为950℃、挤压速度为50 mm/s。利用铅和45号钢毛坯在6.5 MN多向模锻挤压液压机上进行了验证实验。 相似文献
14.
15.
空心坯料反挤压省力成形方法及应用研究 总被引:2,自引:0,他引:2
采用主应力法与数值模拟相结合的方法,研究分析空心坯料反挤压成形力变化规律。结果表明,空心坯料反挤压在减少接触面积的同时,减小了接触面上的单位变形力,大幅度降低了挤压成形力。经在重型车辆铝合金轮辋成形中验证和应用表明,该方法可行,为底部带中心孔的大型薄壁筒形零件的成形,提供了新思路。 相似文献
16.
扁挤压筒可以为扁宽型材挤压提供更有利的金属流动条件,并降低挤压力。在36MN镁挤压机上应用扁挤压筒实现了扁宽型材挤压生产,生产实际经验表明:扁挤压筒内衬应进行优化设计,尽可能降低应力,同时也要保证加工质量,避免产生加工应力;扁挤压筒选材应保证较高强度,并具有良好的热疲劳性能、热稳定性能和加工性能;扁挤压筒外套对应内孔短边的位置应适当减少加热管孔,以利于扁挤压筒整体温度均匀变化;扁挤压筒应进行温度控制和调节,防止其因过热而产生塑性变形。 相似文献
17.
Optimisation of flow balance and isothermal extrusion of aluminium using finite-element simulations 总被引:2,自引:0,他引:2
There is significant demand to reduce variations in the shape and mechanical properties of the aluminium extrusion process to meet tighter tolerance requirements. To reduce variations, the flow and temperature evolution in the container and die must be controlled. To study how the process parameters influence the temperature evolution and the material flow, the effects of ram speed, initial temperature distribution in the billet and container cooling rate have been studied. This work is divided into three parts which examine the different aspects of the extrusion process. (1) To minimize the radial variations of temperature and velocity fields over multiple press cycles. (2) To obtain isothermal extrusion of aluminium. (3) To understand and formulate the effect of an undesired lateral temperature gradient in the billet on the exit velocity of the aluminium sections. In each part, the effect of different process parameters on the flow balance and temperature evolution of the extruded sections is shown and discussed. 相似文献
18.
A three-dimensional steady-state finite element analysis of square die extrusion by using automatic mesh generation 总被引:2,自引:0,他引:2
Steady-state finite element analysis is made for three-dimensional hot extrusion of sections through square dies by using an automatic mesh generator which can generate three-dimensional meshes by shifting two-dimensional meshes. In industrial practice, the design of extrusion dies is still an art rather than science, especially for complicated profiles, because the die design for a new extrusion is developed from previous experience and in-plant trials. The objective of this study is to develop a steady-state finite element method for hot extrusion through square dies, and to provide a theoretical basis for an optimal die design and process control for the extrusion technology. In the present investigation, steady-state assumption is used for both the analyses of deformation and temperature. The analysis of temperature distribution includes heat transfer, and is carried out by decoupling from the analysis of deformation. Convection link element is adopted for the heat transfer analysis between the billet and the container, and also between the billet and the die. Computations are carried out for solid and hollow extrusion of several sections. The present method of analysis has been shown to provide good results comparable with the non-steady-state method with reduced computation time. Distributions of temperature, effective strain rate, velocity and mean stress are discussed for effective design of an extrusion die. 相似文献
19.
基于有限体积法的铜母线连续挤压扩展成形的数值模拟 总被引:2,自引:1,他引:1
对连续挤压几何模型进行简化,基于MSC.SuperForge软件平台,成功实现10mm×80mm铜母线连续挤压扩展成形的有限体积数值模拟,避免了刚塑性有限元法模拟大变形需要多次网格重划,体积损失等难题。获得了金属在模腔内的流动-应力-温度-组织耦合变化规律,详尽的分析了整个扩展变形流动过程与各物理场之间的关系,进一步探明了模腔结构对成形过程的影响。结果表明,在成形过程中,坯料最高温度约为872K,出现在坯料与挡料块接触的表面上;当趋于稳定状态时,扩展腔内坯料温度分布比较均匀一致,约为660K;坯料密度发生了明显变化,镦粗段坯料密度最高,为8.962×103kg/m3,产品成形区域坯料密度最低,在8.750×103kg/m3~8.771×103kg/m3之间。在镦粗段内,坯料与挤压轮的打滑量为32%,在镦粗前,坯料与挤压轮保持同步。坯料作用在腔体上的压力高点出现在腔体挡料块顶端,压力为473MPa。扭矩校核表明,数值模拟结果和实测结果吻合较好。 相似文献
20.
以拐角长悬臂空心铝型材为例,使用Hyper Xtrude分析软件对其挤压过程进行数值模拟,设计正交试验研究了挤压速度、棒料预热温度、挤压筒预热温度、模具预热温度、棒料直径、棒料长度等工艺参数对型材出口截面流速均方差(SDV)和温度均方差(SDT)的影响规律。结果表明:通过极差分析及再次模拟确定最优方案为:挤压速度1 mm·s~(-1),棒料预热温度440℃,挤压筒预热温度420℃,模具预热温度400℃,棒料直径Φ150 mm,棒料长度450 mm,对应的SDV与SDT分别仅为1.3680和1.9130,保证挤出型材获得高的综合质量。通过方差分析得到挤压速度对SDV的影响度及棒料预热温度对SDT的影响度分别高达67.50%和76.41%,定量地表明挤压速度和棒料预热温度分别是影响型材外观质量和内部组织的最主要工艺参数。工厂挤压出的合格产品验证了最优方案的可靠性。 相似文献