A 1-V 10.7-MHz switched-opamp bandpass /spl Sigma//spl Delta/ modulator using double-sampling finite-gain-compensation technique

A 1 V switched-capacitor (SC) bandpass sigma-delta (/spl Sigma//spl Delta/) modulator is realized using a high-speed switched-opamp (SO) technique with a sampling frequency of up to 50 MHz, which is improved ten times more than prior 1 V SO designs and comparable to the performance of the state-of-the-art SC circuits that operate at much higher supply voltages. On the system level, a fast-settling double-sampling SC biquadratic filter architecture is proposed to achieve high-speed operation. A low-voltage double-sampling finite-gain-compensation technique is employed to realize a high-resolution /spl Sigma//spl Delta/ modulator using only low-DC-gain opamps to maximize the speed and to reduce power dissipation. On the circuit level, a fast-switching methodology is proposed for the design of the switchable opamps to achieve a switching frequency up to 50 MHz. Implemented in a 0.35-/spl mu/m CMOS process (V/sub TP/=0.82 V and V/sub TN/=0.65 V) and at 1 V supply, the modulator achieves a measured peak signal-to-noise-and-distortion ratio (SNDR) of 42.3 dB at 10.7 MHz with a signal bandwidth of 200 kHz, while dissipating 12 mW and occupying a chip area of 1.3 mm/sup 2/.     

A time-interleaved continuous-time /spl Delta//spl Sigma/ modulator with 20-MHz signal bandwidth

This paper presents the first implementation results for a time-interleaved continuous-time /spl Delta//spl Sigma/ modulator. The derivation of the time-interleaved continuous-time /spl Delta//spl Sigma/ modulator from a discrete-time /spl Delta//spl Sigma/ modulator is presented. With various simplifications, the resulting modulator has only a single path of integrators, making it robust to DC offsets. A time-interleaved by 2 continuous-time third-order low-pass /spl Delta//spl Sigma/ modulator is designed in a 0.18-/spl mu/m CMOS technology with an oversampling ratio of 5 at sampling frequencies of 100 and 200 MHz. Experimental results show that a signal-to-noise-plus-distortion ratio (SNDR) of 57 dB and a dynamic range of 60 dB are obtained with an input bandwidth of 10 MHz, and an SNDR of 49 dB with a dynamic range of 55 dB is attained with an input bandwidth of 20 MHz. The power consumption is 101 and 103 mW, respectively.     

A time-delay jitter-insensitive continuous-time bandpass /spl Delta//spl Sigma/ modulator architecture

In this paper, we present a new continuous-time bandpass delta-sigma (/spl Delta//spl Sigma/) modulator architecture with mixer inside the feedback loop. The proposed bandpass /spl Delta//spl Sigma/ modulator is insensitive to time-delay jitter in the digital-to-analog conversion feedback pulse, unlike conventional continuous-time bandpass /spl Delta//spl Sigma/ modulators. The sampling frequency of the proposed /spl Delta//spl Sigma/ modulator can be less than the center frequency of the input narrow-band signal.     

80-MHz bandpass /spl Delta//spl Sigma/ modulators for multimode digital IF receivers

Three fully differential bandpass (BP) /spl Delta//spl Sigma/ modulators are presented. Two double-delay resonators are implemented using only one operational amplifier. The prototype circuits operate at a sampling frequency of 80 MHz. The BP /spl Delta//spl Sigma/ modulators can be used in an intermediate-frequency (IF) receiver to combine frequency downconversion with analog-to-digital conversion by directly sampling an input signal from an IF of 60 MHz to a digital IF of 20 MHz. The measured peak signal-to-noise-plus-distortion ratios are 78 dB for 270 kHz (GSM), 75 dB for 1.25 MHz (IS-95), 69 dB for 1.762 MHz (DECT), and 48 dB for 3.84 MHz (WCDMA/CDMA2000) bandwidths. The circuits are implemented with a 0.35-/spl mu/m CMOS technology and consume 24-38 mW from a 3.0-V supply, depending on the architecture.     

A wide-band 280-MHz four-path time-interleaved bandpass sigma-delta modulator

This paper describes a 0.35-/spl mu/m CMOS fourth-order bandpass analog-digital sigma-delta (/spl Sigma//spl Delta/) modulator for wide-band base stations receivers. The modulator, based on a time-interleaved four-path architecture, achieves an equivalent sampling frequency of 280 MHz, although the building blocks operate at only 70 MHz. In measurements, the prototype chip achieves a dynamic range of 72 dB (12 bits of resolution) with a signal bandwidth of 4.375 MHz centered around an intermediate frequency of 70 MHz. The measured spurious-free dynamic range is 69 dB. The /spl Sigma//spl Delta/ modulator dissipates 480 mW from a 3.3-V supply, including voltage reference buffers and output pads with high-driving capabilities, and occupies 20 mm/sup 2/ of silicon area.     

Tunable continuous-time bandpass /spl Sigma//spl Delta/ modulators with fractional delays

An analytical design methodology for continuous-time (CT) bandpass (BP) /spl Sigma//spl Delta/ modulators is presented. Second- and fourth-order tunable continuous time BP /spl Sigma//spl Delta/ modulator design equations are presented. A novel /spl Sigma//spl Delta/ loop architecture, where the traditional CT BP loop filter function is replaced with the filter function with fractional delays, is proposed. Validity of the methodology is confirmed by mixed-signal behavioral simulations.     

A 1-MHz-bandwidth second-order continuous-time quadrature bandpass sigma-delta modulator for low-IF radio receivers

This paper presents a quadrature bandpass /spl Sigma//spl Delta/ modulator with continuous-time architecture. Due to the continuous-time architecture and the inherent anti-aliasing filter, the proposed /spl Sigma//spl Delta/ modulator needs no additional anti-aliasing filter in front of the modulator in contrast to quadrature bandpass /spl Sigma//spl Delta/ modulators with switched-capacitor architectures. The second-order /spl Sigma//spl Delta/ modulator digitizes complex analog I/Q input signals at 1-MHz intermediate frequency and operates within a clock frequency range of 25-100 MHz. The modulator chip achieves a peak signal-to-noise-distortion ratio (SNDR) of 56.7 dB and a dynamic range of 63.8 dB within a 1-MHz signal bandwidth and at a clock frequency of 100 MHz. Furthermore, it provides an image rejection of at least 40 dB. The 0.65-/spl mu/m BiCMOS chip consumes 21.8 mW at 2.7-V supply voltage.     

Architecture, design, and test of continuous-time tunableintermediate-frequency bandpass delta-sigma modulators

This paper examines the architecture, design, and test of continuous-time tunable intermediate-frequency (IF) fourth-order bandpass delta-sigma (BP ΔΣ) modulators. Bandpass modulators sampling at high IFs (~100 MHz) allow direct sampling of the RF signal-reducing analog hardware and make it easier to realize completely software programmable receivers. This paper presents circuit design of and test results from continuous-time fourth-order BP ΔΣ modulators fabricated in AlInAs/GaInAs heterojunction bipolar technology with a peak unity current gain cutoff frequency (f_T) of 80 GHz and a maximum frequency of oscillation (f_MAX) of about 130 GHz. Operating from ±5-V power supplies, a fabricated 180-MHz IF fourth-order ΔΣ modulator sampling at 4 GS/s demonstrates stable behavior and achieves 75.8 dB of signal-to-(noise+distortion)-ratio (SNDR) over a 1-MHz bandwidth. Narrowband performance (~1 MHz) performance of these modulators is limited by thermal/device noise while broadband performance (~60 MHz), is limited by quantization noise. The high sampling frequency (4 GS/s) in this converter is dictated by broadband (60 MHz) performance requirements     

A 10.7-MHz self-calibrated switched-capacitor-based multibit second-order bandpass /spl Sigma//spl Delta/ modulator with on-chip switched buffer

A second-order multibit bandpass /spl Sigma//spl Delta/ modulator (BP/spl Sigma//spl Delta/M) used for the digitizing of AM/FM radio broadcasting signals at a 10.7-MHz IF is presented. The BP/spl Sigma//spl Delta/M is realized with switched-capacitor (SC) techniques and operates with a sampling frequency of 37.05 MHz. The input impulse current, required by the SC input branch, is minimized by the use of a switched buffer without deteriorating the overall system performance. The accuracy of the in-band noise shaping is ensured with two self-calibrating control systems. In a 0.18-/spl mu/m CMOS technology, the device die size is 1 mm/sup 2/ and the power consumption is 88 mW. In production, the BP/spl Sigma//spl Delta/M features at least 78-dB dynamic range and 72-dB peak SNR within a 200-kHz bandwidth (FM bandwidth). The intermodulation (IMD) is -65 dBc for two tones at -11 dBFS. The robustness of the aforementioned performance is demonstrated by the fact that it has been realized with the BP/spl Sigma//spl Delta/M embedded in the noisy on-chip environment of a complete mixed-signal FM receiver.     

A 2-GS/s 3-bit /spl Delta//spl Sigma/-modulated DAC with tunable bandpass mismatch shaping

Direct digital synthesis of signals in the hundreds of megahertz can lead to simpler, smaller transceivers, free of images and LO feedthrough that plague systems requiring analog upconversion. We present a 3-bit, 2 GS/s, /spl Delta//spl Sigma/-modulated DAC in InP HBT technology. The DAC is linearized using bandpass mismatch shaping. The mismatch shaper uses seven tunable 1.5-bit discrete-time bandpass /spl Delta//spl Sigma/ modulators to dynamically route the digital signals to the DACs. These /spl Delta//spl Sigma/ modulators operate in the analog domain to decrease system complexity and power consumption. The mismatch-shaped DAC can generate narrowband signals between 250-750 MHz with >68 dB SNR in a 1-MHz bw, >74-dB SFDR, and <-80-dBc intermodulation distortion with an 8.1-W power consumption.     

A 92-MHz 13-bit IF digitizer using optimized SC integrators in 0.35-/spl mu/m CMOS technology

A feedforward compensation scheme with no Miller capacitors is proposed to overcome the bandwidth limitations of traditional Miller compensation schemes. The technique has been used in the design of an operational transconductance amplifier (OTA) with a dc gain of 80 dB, gain bandwidth of 1.4 GHz, phase margin of 62/spl deg/, and 2 ns settling time for 2-pF load capacitor in a standard 0.35-/spl mu/m CMOS technology. The OTA's current consumption is 4.6 mA. The OTA is used in the design of a fourth-order switched-capacitor bandpass /spl Sigma//spl Delta/ modulator with a clock frequency of 92 MHz. It achieves a peak signal-to-noise ratio of 80 and 54 dB for 270-kHz (GSM) and 3.84-MHz (CDMA) bandwidths, respectively and consumes 19 mA of current from a /spl plusmn/1.25-V supply.     

A 14-bit delta-sigma ADC with 8/spl times/ OSR and 4-MHz conversion bandwidth in a 0.18-/spl mu/m CMOS process

A 14-bit 8/spl times/ oversampling delta-sigma (/spl Delta//spl Sigma/) analog-to-digital converter (ADC) for wide-band communication applications has been developed. By using a novel architecture, a high maximum out-of-band quantization noise gain (Q/sub max/) is realized, which greatly improves the SNR and tonal behavior. The ADC employs a fifth-order single-stage structure with a 4-bit quantizer. It achieves 82-dB SNDR and 103-dB SFDR at 4-MHz conversion bandwidth with a single 1.8-V power supply.     

A 250-kHz 94-dB double-sampling /spl Sigma//spl Delta/ modulation A/D converter with a modified noise transfer function

This paper presents a high-order double-sampling single-loop /spl Sigma//spl Delta/ modulation analog-to-digital (A/D) converter. The important problem of noise folding in double-sampling circuits is solved here at the architectural level by placing one of the zeros in the modulator's noise transfer function at half the sampling frequency instead of in the baseband. The resulting modulator is of fifth order but has the baseband performance of a fourth-order modulator. Through the use of an efficient switched-capacitor implementation, the overall circuit uses only four operational amplifiers and hence, its complexity is similar to that of a fourth-order modulator. An experimental 1-bit modulator was designed for an oversampling ratio of 96 and a bandwidth of 250 kHz at a 3.3-V supply in a conservative 0.8-/spl mu/m standard CMOS process. Due to the double-sampling, the sampling frequency is 48 MHz, although the circuits operate at a clock frequency of only 24 MHz. The circuit achieves a dynamic range of 94 dB. The peak signal-to-noise ratio and signal-to-noise-plus-distortion ratio were measured to be 90 and 86 dB, respectively. The power consumption of the complete circuit including clock drivers and output pad drivers was 43 mW. The analog blocks (opamps, comparators, etc.) consume 30 mW of this total.     

A 75-dB image rejection IF-input quadrature-sampling SC /spl Sigma//spl Delta/ Modulator

Quadrature sampling of intermediate frequency (IF) signals is subject to the well-known problem of gain and phase mismatches between the in-phase (I) and quadrature (Q) channels. This paper presents an IF-input quadrature-sampling switched-capacitor (SC) /spl Sigma//spl Delta/ modulator that circumvents the I/Q mismatch problem by time-sharing between the I and Q channels the critical circuit components, namely, the sampling capacitor and the capacitor of the first-stage feedback digital-to-analog converter (DAC). In addition, a clocking scheme that is insensitive to I/Q phase imbalance is used. A third-order single-loop 1-bit low-pass modulator has been designed and fabricated in a 0.35-/spl mu/m CMOS process with an active area of 0.57mm/sup 2/. The experimental results show that the modulator achieves an image-rejection ratio (IRR) of greater than 75dB throughout a 200-kHz signal bandwidth.     

Hybrid /spl Sigma//spl Delta/ modulators with adaptive calibration

This paper describes an architecture for stable high-order /spl Sigma//spl Delta/ modulation. The architecture is based on a hybrid /spl Sigma//spl Delta/ modulator, wherein hybrid integrators replace conventional analog integrators. The hybrid integrator, which is a combination of an analog integrator and a digital integrator, offers an increased dynamic range and helps make the resulting high-order /spl Sigma//spl Delta/ modulator stable. However, the hybrid /spl Sigma//spl Delta/ modulator relies on precise matching of analog and digital paths. In this paper, a calibration technique to alleviate possible mismatch between analog and digital paths is proposed. The calibration adaptively adjusts the digital integrators so that their transfer functions match the transfer functions of corresponding analog integrators. Through behavioral-level simulations of fourth-order /spl Sigma//spl Delta/ modulators, the calibration technique is verified.     

A 3.3-mW /spl Sigma//spl Delta/ modulator for UMTS in 0.18-/spl mu/m CMOS with 70-dB dynamic range in 2-MHz bandwidth

A quadrature fourth-order, continuous-time, /spl Sigma//spl Delta/ modulator with 1.5-b quantizer and feedback digital-to-analog converter (DAC) for a universal mobile telecommunication system (UMTS) receiver chain is presented. It achieves a dynamic range of 70 dB in a 2-MHz bandwidth and the total harmonic distortion is -74 dB at full-scale input. When used in an integrated receiver for UMTS, the dynamic range of the modulator substantially reduces the need for analog automatic gain control and its tolerance of large out-of-band interference also permits the use of only first-order prefiltering. An IC including an I and Q /spl Sigma//spl Delta/ modulator, phase-locked loop, oscillator, and bandgap dissipates 11.5 mW at 1.8 V. The active area is 0.41 mm/sup 2/ in a 0.18-/spl mu/m 1-poly 5-metal CMOS technology.     

A 64-MHz clock-rate /spl Sigma//spl Delta/ ADC with 88-dB SNDR and -105-dB IM3 distortion at a 1.5-MHz signal frequency

A 64-MHz clock rate sigma-delta (/spl Sigma//spl Delta/) analog-to-digital converter (ADC) with -105-dB intermodulation distortion (IMD) at a 1.5-MHz signal frequency is reported. A linear replica bridge sampling network enables the ADC to achieve high linearity for high signal frequencies. Operating at an oversampling ratio of 29, a 2-1-1 cascade with a 2-b quantizer in the last stage reduces the quantization noise level well below that of the thermal noise. The measured signal-to-noise and distortion ratio (SNDR) in 1.1-MHz bandwidth is 88 dB, and the spurious-free-dynamic-range (SFDR) is 106 dB. The modulator and reference buffers occupy a 2.6-mm/sup 2/ die area and have been implemented with thick oxide devices, with minimum channel length of 0.35 /spl mu/m, in a dual-gate 0.18-/spl mu/m 1.8-V single-poly five-metal (SP5M) digital CMOS process. The power consumed by the ADC is 230 mW, including the decimation filters.     

Design and implementation of quadrature bandpass sigma-delta modulator used in low-IF RF receiver

This paper presents the design and implementation of quadrature bandpass sigma-delta modulator.A pole movement method for transforming real sigma-delta modulator to a quadrature one is proposed by detailed study of the relationship of noise-shaping center frequency and integrator pole position in sigma-delta modulator.The proposed modulator uses sampling capacitor sharing switched capacitor integrator,and achieves a very small feedback coefficient by a series capacitor network,and those two techniques can dramatically reduce capacitor area.Quantizer output-dependent dummy capacitor load for reference voltage buffer can compensate signal-dependent noise that is caused by load variation.This paper designs a quadrature bandpass Sigma-Delta modulator for 2.4 GHz low IF receivers that achieve 69 dB SNDR at 1 MHz BW and-1 MHz IF with 48 MHz clock.The chip is fabricated with SMIC 0.18 μm CMOS technology,it achieves a total power current of 2.1 mA,and the chip area is 0.48 mm2.     

A CMOS oversampling bandpass cascaded D/A converter with digital FIR and current-mode semi-digital filtering

An oversampling bandpass digital-to-analog converter has been designed so as to eliminate the carrier leak and in-band SNR degradation that accompany I and Q channel mismatch in wireless transmitters. The converter combines a cascaded noise-shaping sigma-delta (/spl Sigma//spl Delta/) modulator with digital finite impulse response (FIR) and mixed-signal semi-digital filters that attenuate out-of-band quantization noise. The performance of the converter in the presence of current source mismatch has been improved through the use of bandpass data weighted averaging. An experimental prototype of the converter, integrated in a 0.25-/spl mu/m CMOS technology, provides 83 dB of dynamic range for a 6.25-MHz signal band centered at 50 MHz, and suppresses out-of-band quantization noise by 38 dB.     

The tiling phenomenon in /spl Sigma//spl Delta/ modulation

The theoretical error signal analysis of a sigma-delta (/spl Sigma//spl Delta/) modulator is a difficult problem due to the presence of a nonlinear operation (the amplitude quantization) in a feedback loop. In this paper, new deterministic knowledge on the transfer function of a /spl Sigma//spl Delta/ modulator is established, thanks to some recently observed properties of its state variables. For a large class of typical /spl Sigma//spl Delta/ modulators with constant inputs, the state variables appear to remain in a tile. We show what characteristics in a /spl Sigma//spl Delta/ modulator are specifically responsible for this property and give some initial proof of it. Under a constant input, the tiling phenomenon has as fundamental consequence that the output is a fixed and memoryless modulo function of n successive integrated versions of the input. This gives the theoretical knowledge that the modulator has an equivalent feedforward circuit expression. We give some immediate theoretical consequences on error analysis including the case of time-varying inputs.