Efficient Preparation of Submicrometer α-Alumina Powders by Calcining Carbon-Covered Alumina

A simple method is described to prepare submicrometer α-alumina by burning carbon supported on the surface of γ-alumina in oxygen flow at a temperature of 800°C. The burning of carbon generates a large amount of heat and leads to a rapid increase in the local temperature inside the pores of alumina. When the temperature is high enough for the phase transformation, α-alumina is obtained in a very short time. It was found that, for carbon contents between 6 and 10 wt%, all the γ-alumina could transform into α-alumina after burning of carbon in oxygen for a short time, and the transformed particle sizes of α-alumina were mostly no more than 1 μm.     

Effect of Pore Size Distribution of Carbon-Covered Alumina on the Preparation of Submicrometer α-Alumina Powders

Calcining carbon-covered alumina (CCA) samples at 800°C in an oxygen flow is an efficient method to prepare α-alumina powders. It is found that the pore size distribution of CCA samples, which depends on the carbon content and the pore size distribution of the precursor alumina used, is one of the key factors for the total conversion of γ-alumina to α-alumina and the complete combustion of carbon in the pores of alumina. No matter how high the carbon content, total conversion does not occur for CCA samples prepared from alumina possessing the most probable pore size of about 5.2 nm. Using γ-alumina with the most probable pore size of 6.1 nm as the precursor of CCA samples, total transformation occurs when the carbon content of CCA ranges from 11.9 to 17.3 wt%, but the color of as-prepared α-alumina is not pure white but light gray. Polyethylene glycol (PEG 20 000), added to the sucrose/γ-alumina system, can expand the pores of CCA samples after carbonization, and calcining of thus-prepared CCA results in a complete transformation of γ-alumina to pure white α-alumina with a particle size of about 1 μm when the carbon content of CCA is between 6 and 19 wt%.     

Sintering of Mixtures of Seeded Boehmite and Ultrafine α-Alumina

α-Alumina was fabricated by dry pressing mixtures of seeded boehmite and fine α-alumina (i.e., 0.2 and 0.3 μm diameter) to reduce the large shrinkage of boehmite-derived α-alumina. The maximum green density was obtained with mixtures containing ∼70%α-alumina for both alumina powders. The ∼15% linear shrinkage and microstructures of these samples were comparable to 100% alumina powder samples. Samples with 0.2 μm alumina sintered to densities >95% at 1300°C whereas 1400°C was needed for samples with 0.3 μm alumina. These results indicate that boehmite can be used as a substitute for relatively expensive ultrafine α-alumina powders.     

New Sol–Gel Route for the Preparation of Pure α-Alumina at 950°C

An anhydrous alumina (Al₂O₃) sol was prepared from aluminum isopropoxide and an organic solvent, using an acetic acid stabilizer. The complete conversion of the dried sol to α-Al₂O₃ was accomplished at a temperature of 950°C by a single transition via γ-Al₂O₃. Al₂O₃ that was deposited via dip coating resulted in amorphous films, even after annealing at 1100°C, because of the silicon diffusion from the substrate. This phenomenon was avoided using a rapid thermal treatment in a flame after dip coating, which resulted in uniform thin films that are converted to α-Al₂O₃ via heat treatment.     

Kinetics and Microstructural Evolution of Heterogeneous Transformation of θ-Alumina to α-Alumina

Ultrafine (<0.1 μm) high-purity θ-Al₂O₃ powder containing 3–17.5 mol%α-Al₂O₃ seeds was used to investigate the kinetics and microstructural evolution of the θ-Al₂O₃ to α-Al₂O₃ transformation. The transformation and densification of the powder that occurred in sequence from 960° to 1100°C were characterized by quantitative X-ray diffractometry, dilatometry, mercury intrusion porosimetry, and transmission and scanning electron microscopy. The relative bulk density and the fraction of α phase increased with annealing temperature and holding time, but the crystal size of the α phase remained ∼50 nm in all cases at the transformation stage (≤1020°C). The activation energy and the time exponent of the θ to α transformation were 650 ± 50 kJ/mol and 1.5, respectively. The results implied the transformation occurred at the interface via structure rearrangement caused by the diffusion of oxygen ions in the Al₂O₃ lattice. A completely transformed α matrix of uniform porosity was the result of appropriate annealing processes (1020°C for 10 h) that considerably enhanced densification and reduced grain growth in the sintering stage. The Al₂O₃ sample sintered at 1490°C for 1 h had a density of 99.4% of the theoretical density and average grain size of 1.67 μm.     

Synthesis of Magnesium Aluminate Spinel Platelets from α-Alumina Platelet and Magnesium Sulfate Precursors

Spinel platelets were formed from a powder mixture of 3–5 μm wide and 0.2–0.5 μm thick α-Al₂O₃ and 1–8 μm (average 3 μm) MgSO₄ heated 2 h at 1200°C. The hexagonal platelet shape of the original α-Al₂O₃ platelet was maintained in the spinel, although their size was slightly increased and their surface roughened. When a mixture of α-Al₂O₃ platelets and MgO powder was heated 3 h at 1400°C, the spinel formed lost the platelet morphology of the alumina.     

Seeding with γ-Alumina for Transformation and Microstructure Control in Boehmite-Derived α-Alumina

The dehydration, transformation, and densification of boehmite (γ-AlOOH) are enhanced by addition of γ-Al₂O₃ seed particles. α-Al₂O₃ microstructures with uniform 1- to 2-μm grain size and sintered densities 98% of theoretical are achieved at 1300°C Thermal analysis shows that γ-Al₂O₃ seed particles transform to α-Al₂O₃ before the matrix, thus controllably nucleating the transformation of θ-AI₂O₃ to α-Al₂O₃.     

Effect of Calcination on the Sintering of Gel-Derived, Zirconia-Toughened Alumina

The densification behavior of ZrO₂ (+ 3 mol% Y₂O₃)/85 wt% Al₂O₃ powder compacts, prepared by the hydrolysis of metal chlorides, can be characterized by a transition- and an α-alumina densification stage. The sintering behavior is strongly determined by the densification of the transition alumina aggregates. Intra-aggregate porosity, resulting from calcination at 800°C, partly persists during sintering and alumina phase transformation and negatively influences further macroscopic densification. Calcination at 1200°C, however, densifies the transition alumina aggregates prior to sintering and enables densification to almost full density (96%) within 2 h at 1450°C, thus obtaining a microstructure with an alumina and a zirconia grain size of 1 μm and 0.3–0.4 μm, respectively.     

Morphological Forms of α-Alumina Particles Synthesized in 1,4-Butanediol Solution

Phase-pure, monodispersed, hexagonal plates of single-crystal α-alumina (∼ 2 μm wide and ∼0.5 μm thick) have been prepared via precipitation by treating an aluminum hydrous oxide precursor in 1,4-butanediol at 300°C under autogenous vapor pressure. Present work shows that KOH is the only reagent that precipitates an aluminum hydrous oxide precursor suitable to synthesize α-alumina in 1,4-butanediol solution. In contrast, the use of NaOH or NH₄OH as the precipitating reagent for the precursor material does not yield the alpha phase. The solution pH at which the precursor materials are precipitated is also a critical factor for the formation of α-Al₂O₃. Phase-pure α-alumina powders were also only synthesized from the aluminum hydrous oxide precursors precipitated in the pH range from 10 to 10.5. The results of X-ray diffraction and scanning electron microscopy indicate that longer reaction times promote the phase transformation from the intermediate boehmite phase to α-alumina. The complete transformation from boehmite to α-alumina requires reaction times of about 12 h.     

Phase Transformation in Nanometer-Sized γ-Alumina by Mechanical Milling

Nanocrystalline γ-alumina powders of 50-nm size were milled by high-energy ball milling. It was found that the pure γ-alumina phase showed great stability and did not transform to any other phase even after a long milling time. On the other hand, γ-alumina, which contained a small amount of the α-alumina phase, showed a gradual phase transformation from γ- to α-alumina on milling. The phase transformation mechanism during milling appears to be nucleation and growth type and promoted by the α-alumina seed.     

Preparation of Larnthanum β-Alumina with High Surface Area by Coprecipitation

Mixtures of La₂O₃ and Al₂O₃ with various La contents were prepared by co-precipitation from La(NO₃)₃ and Al(NO₃)₃ solutions and calcined at 800° to 1400°C. The addition of small amounts of La₂O₃ (2 to 10 mol%) to Al₂O₃ gives rise to the formation of lanthanum β-alumina (La 2 O₃·11–14Al₂O₃) upon heating to above 1000°C and retards the transformation of γ-Al₂O₃ to α-Al₂O₃ and associated sintering.     

Influence of Pyridine–Borane on the Sintering Behavior and Properties of α-Silicon Carbide

In the present study, α-SiC powder is coated with pyridineborane (BH₃·C₅H₅N), a liquid molecular compound, which forms a boron carbonitride (BC_3.5N) layer by heat treatment at 1000°C under argon. The precipitation method leads to an improved chemical homogeneity in the compacted powder resulting in enhanced densification and significant reduction in grain growth during subsequent sintering at temperatures exceeding 2070°C. Thus, small average grain sizes of d ₅₀= 1.3 μm and a narrow grain size distribution ( d ₁₀= 0.6 μm, d ₉₀= 2.2 μm) are detected in the liquid-phase-processed sample sintered at 2200°C for 0.5 h in argon. Final densities of at least 98% of theoretical could be obtained by pressureless sintering at 2100°C. These results as well as the microstructural distribution of the sintering aids in the densified samples are discussed.     

Mechanical-Activation-Triggered Gibbsite-to-Boehmite Transition and Activation-Derived Alumina Powders

Mechanical activation of monoclinic gibbsite (Al(OH)₃) in nitrogen led to the formation of nanocrystalline orthorhombic boehmite (AlOOH) at room temperature. The boehmite phase formed after merely 3 h of mechanical activation and developed steadily as the mechanical-activation time increased. Forty hours of mechanical activation resulted in essentially single-phase boehmite, together with α-alumina (α-Al₂O₃) nanocrystallites 2–3 nm in size. The sequence of phase transitions in the activation-derived boehmite was as follows: boehmite to γ-Al₂O₃ and then to α-Al₂O₃ when flash-calcined at a heating rate of 10°C/min in air. γ-Al₂O₃ formed at 520°C, and flash calcination to 1100°C led to the formation of an α-Al₂O₃ phase, which exhibited a refined particle size in the range of 100–200 nm. In contrast, the gibbsite-to-boehmite transition in the unactivated gibbsite occurred over the temperature range of 220°–330°C. A flash-calcination temperature of 1400°C was required to complete the conversion to α-Al₂O₃ phase, with both δ-Al₂O₃ and θ-Al₂O₃ as the transitional phases. The resulting alumina powder consisted of irregularly shaped particles 0.4–0.8 μm in size, together with an extensive degree of particle agglomeration.     

Processing and Microstructure Development in Alumina–Silicon Carbide Intragranular Particulate Composites

Al₂O₃–SiC particulate composites were fabricated by hot-pressing mixtures of 5–30 vol% SiC with either α-Al₂O₃, γ-Al₂O₃, or boehmite (γ-AlOOH) to determine whether grain growth or the α-alumina phase transformation could be used to fabricate intragranular particulate composites. Samples starting with α-alumina resulted in primarily intergranular SiC of 0.3 μ and an alumina grain size of 1.5–4.1 μm. Heat treatments resulted in SiC coarsening but no entrapment of SiC by grain boundary breakaway. The α-alumina transformation in the samples starting with γ-alumina resulted in the entrapment of ∼48% of the 5 vol% of SiC added whereas 79% of the SiC was entrapped in the α-alumina grains in samples starting with boehmite. Only SiC particles ≤0.2 SmUm were entrapped in the α-alumina grains during the phase transformation. With increasing SiC content, the relative volume of intragranular SiC decreased, but the amount of intragranular SiC was constant and independent of the amount of SiC added before transformation. The formation of intragranular composites from γ-alumina and boehmite samples was explained with a model that attributes particle entrapment to the vermicular growth of α-alumina into the transition alumina matrix during the α-alumina phase transformation. Seeding the boehmite-based samples did not affect the concentration of entrapped SiC, but did lower the hot-pressing densification temperature by as much as 150°C.     

Liquid-Phase-Assisted Transformation of Seeded γ-Alumina

α-Al₂O₃-seeded, boehmite-derived γ-Al₂O₃ was transformed in the presence of V₂O₅, resulting in a 205°C decrease in the α-Al₂O₃ transformation temperature and a 74% reduction in the apparent activation energy for the γ- to α-Al₂O₃ transformation at temperatures greater than 850°C. These changes are attributed to the lowered energy barrier for nucleation by seeding and the lowered activation energy for material transport through the liquid relative to the unseeded, solid-state transformation. Growth of the transforming alumina yielded fine-grained α-Al₂O₃ particles which exhibited a highly faceted morphology. It is proposed that the combined control of both nucleation and growth during liquid-phase-assisted transformation provides a potentially powerful technique for tailoring powder characteristics in many material systems which undergo nucleation and growth processes.     

Texture Development by Templated Grain Growth in Liquid-Phase-Sintered α-Alumina

The distribution and orientation of platelet-shaped particles of α-alumina in a fine-grained alumina matrix is shown to template texture development via anisotropic grain growth. The textured microstructure ranges from 4 wt% oriented platelet particles in calcined samples to nearly 100% oriented α-Al₂O₃ grains after sintering at 1400°C. A CaO + SiO₂ liquid phase creates favorable thermodynamic and kinetic conditions for anisotropic grain growth and grain reorientation during sintering. Important criteria for templated grain growth include (1) anisotropic crystal structure and growth, (2) high thermodynamic driving force for template grain growth, and (3) modification of diffusion in the system to continuously provide material to the anisotropically growing template grains.     

Preparation of Nanometer-Sized α-Alumina Powders by Calcining an Emulsion of Boehmite and Oleic Acid

This study proposes a method to form ultrafine α-Al₂O₃ powders. Oleic acid is mixed with Al(OH)₃ gel. The gel is the precursor of the Al₂O₃. After it is mixed and aged, the mixture is calcined in a depleted oxygen atmosphere between 25° and 1100°C. Oleic acid evaporates and decomposes into carbon during the thermal process. Residual carbon prevents the growth of agglomerates during the formation of α-Al₂O₃. The phase transformation in this process is as follows: emulsion →γ-Al₂O₃→δ-Al₂O₃→θ-Al₂O₃→α-Al₂O₃. This process has no clear θ phase. Aging the mixed sample lowers the formation temperature of α-Al₂O₃ from 1100° to 1000°C. The average crystallite diameter is 60 nm, measured using Scherrer's equation, which is consistent with TEM observations.     

Synthesis of Thermally Stable χ-Alumina by Thermal Decomposition of Aluminum Isopropoxide in Toluene

Thermal decomposition of aluminum isopropoxide in toluene at 315°C resulted in χ-alumina that had high thermal stability, whereas the reaction at lower temperatures resulted in formation of an amorphous product. The χ-alumina thus obtained directly transformed to α-alumina at ∼1150°C, bypassing the other transition alumina phases, whereas the amorphous product transformed to γ-alumina and then to θ-alumina before final transformation to α-alumina. When the χ-alumina, solvothermally synthesized at 315°C, was recovered by the removal of the solvent at the reaction temperature, thermal stability of the product was improved further. This procedure is convenient because it avoids bothersome work-up processes that yield large-surface-area and large-pore-volume alumina.     

Preparation of Monodisperse, Spherical Alumina Powders from Alkoxides

Monodisperse, spherical alumina powders were prepared by the controlled hydrolysis of aluminum alkoxide in a dilute solution consisting of octanoi and acetonitrile. The reagent concentration influenced the particle size, size distribution, morphology, and state of agglomeration. The addition of acetonitrile and octanol affected both particle shape and the state of agglomeration and prevented gelation during hydrolysis. Sub-micrometer-sized alumina particles grew to 10 μm with increased concentration of hydroxypropylcellulose dispersant. As-prepared amorphous powders crystal-lized to γ-alumina at 1000°C and converted to α-alumina at 1150°C without intermediate phases. The particle morphology was retained after crystallization to γ-alumina.     

Growth of α-AI2O3 Platelets in the HF-γy-AI2O3 System

In the presence of a fluorine mineralizer, highly aggregated, <5 μm α-Al₂O₃ platelet particles form by vapor transport during the thermal transformation of γ-alumina. Platelet aggregation was determined to occur by platelet inter-growth and by edge nucleation on primary α-Al₂0₃ platelets. The addition of 10¹⁰α-alumina seed particles/cm³γ–Al₂O₃ resulted in the development of discrete particles during the initial stage of transformation. Impingement of the growing platelets during the latter stage of transformation, however, resulted in intergrowth, a process which was not changed by seeding. Particle size distribution broadening was observed to increase with increasing HF and H₂O concentrations because vapor reactant supersaturation increases the degree of edge nucleation. When initially low HF and H₂O concentrations were used in seeded systems, however, essentially aggregate-free α-Al₂O₃ platelets of 10–15 μm were obtained.