A new single-phase ZCS-PWM boost rectifier with high power factor and low conduction losses

This paper proposes a new single-phase high-power-factor rectifier, which features regulation by conventional pulsewidth modulation (PWM), soft commutation, and instantaneous average line current control. A new zero-current switching PWM (ZCS-PWM) auxiliary circuit is configured in the presented ZCS-PWM rectifier to perform ZCS in the active switches and zero-voltage switching (ZVS) in the passive switches. Furthermore, soft commutation of the main switch is achieved without additional current stress by the presented ZCS-PWM auxiliary circuit. A significant reduction in the conduction losses is achieved because of the following reasons: 1) the circulating current for the soft switching flows only through the auxiliary circuit; 2) a minimum number of switching devices are involved in the circulating current path; and 3) the proposed rectifier uses a single converter instead of the conventional configuration composed of a four-diode front-end rectifier followed by a boost converter. Seven transition states for describing the behavior of the ZCS-PWM rectifier in one switching period are described. The PWM-switch model is used to predict the system performance. A prototype rated at 1 kW, operating at 60 kHz, with an input alternating current voltage of 220 V/sub rms/ and an output voltage of 400 V/sub dc/, has been implemented in laboratory. An efficiency of 98.3% and a power factor over 0.99 have been measured. Analysis, design, and the control circuitry are also presented in this paper.     

A novel zero-Voltage-switching PWM boost rectifier with high power factor and low conduction losses

This paper proposes a new single-phase high-power-factor rectifier, which features regulation by conventional pulsewidth modulation (PWM), soft commutation, and instantaneous average line current control. A new zero-voltage-switching PWM (ZVS-PWM) auxiliary circuit is configured in the presented ZVS-PWM rectifier to perform ZVS in the main switches and the passive switches, and zero-current switching in the auxiliary switch. Furthermore, soft commutation of the main switch is achieved without additional current stress by the presented ZVS-PWM auxiliary circuit. A significant reduction in the conduction losses is achieved, since the circulating current for the soft switching flows only through the auxiliary circuit and a minimum number of switching devices are involved in the circulating current path, and the proposed rectifier uses a single converter instead of the conventional configuration composed of a four-diode front-end rectifier followed by a boost converter. Nine transition states for describing the behavior of the ZVS-PWM rectifier in one switching period are described. A prototype rated at 1 kW, operating 80 kHz, with an input ac voltage of 220 V/sub rms/ and an output voltage of 400 V/sub dc/ has been implemented in the laboratory. An efficiency of 96.7% and power factor over 0.99 has been measured. Analysis, design, and the control circuitry are also presented in this paper.     

An improved ZCS-PWM commutation cell for IGBT's application

An improved zero-current-switching pulsewidth-modulation (ZCS-PWM) commutation cell is proposed, which is suitable for high-power applications using insulated gate bipolar transistors (IGBTs) as the power switches. It provides ZCS operation for active switches with low-current stress without voltage stress and PWM operating at constant frequency. The main advantage of this cell is a substantial reduction of the resonant current peak through the main switch during the commutation process. Therefore, the RMS current through it is very close to that observed in the hard-switching PWM converters. Also, small ratings auxiliary components can be used. To demonstrate the feasibility of the proposed ZCS-PWM commutation cell, it was applied to a boost converter. Operating principles, theoretical analysis, design guidelines and a design example are described and verified by experimental results obtained from a prototype operating at 40 kHz, with an input voltage rated at 155 V and 1 kW output power. The measured efficiency of the improved ZCS-PWM boost converter is presented and compared with that of hard-switching boost converter and with some ZCS-PWM boost converters presented in the literature. Finally, this paper presents the application of the proposed soft-switching technique in DC-DC nonisolated power converters     

A novel zero-current-transition full bridge DC/DC converter

This paper proposes a novel zero-current-transition pulse-width modulation full-bridge dc/dc converter. The proposed converter not only achieves zero current switching for the main switches and auxiliary switch in the entire load ranges, but it also realizes soft commutation for the output rectifier diodes. Furthermore, the auxiliary circuit also helps to turn on the main switches softly. Simulation results and experimental results verify the theoretical analysis.     

电流型零电压开关节能整流器

为解决电流型脉冲宽度调制（Pulse Width Modulation,PWM）整流器在高开关频率下硬切换时的开关损耗问题,提出了一种电流型零电压开关节能整流器,其辅助谐振电路位于直流环节,且与直流母线并联,只有1个辅助开关.在换流过程中,主开关能实现零电压切换,辅助开关能实现零电流切换,而且当整流器采用多电平PWM控制策略时,辅助电路在每个开关周期只需工作1次.分析了谐振换流过程,仿真结果表明特征仿真波形符合理论分析,开关器件切换时处于软开关状态,整流器能平稳运行.该电流型零电压开关节能整流器可以在高开关频率和大功率的应用场合实现高效率运行.     

A simple active auxiliary commutation circuit for three-level PWMsingle-phase inverters

This paper presents the analysis and design of a new low-loss auxiliary circuit for three-level pulsewidth-modulation single-phase full-bridge inverters which achieve soft switching at all semiconductor devices. The active auxiliary commutation circuit (AACC) is composed of an LC circuit and two bidirectional switches, where one auxiliary switch commutates under zero-voltage switching condition and the other under zero-current switching condition. The AACC dispenses with the use of auxiliary voltage sources. Low reactive energy is added to the converter, resulting in low RMS current stresses at the main switches and, consequently, higher efficiency is achieved. Auxiliary circuit design procedures and experimental results are presented to prove the operation principle     

New family of zero-current-switching PWM converters using a new zero-current-switching PWM auxiliary circuit

A new family of zero-current-switching (ZCS) pulsewidth-modulation (PWM) converters using a new ZCS-PWM auxiliary circuit is presented in this paper. The main switch and auxiliary switch operate at ZCS turn-on and turn-off, and the all-passive semiconductor devices in the ZCS-PWM converters operate at zero-voltage-switching (ZVS) turn-on and turn-off. Besides operating at constant frequency and reducing commutation losses, these new converters have no additional current stress and conduction loss in the main switch in comparison to the hard-switching converter counterpart. The PWM switch model and state-space averaging approach is used to estimate and examine the steady-state and dynamic character of the system. The new family of ZCS-PWM converters is suitable for high-power applications using insulated gate bipolar transistors (IGBTs). The principle of operation, theoretical analysis, and experimental results of the new ZCS-PWM boost converter, rated 1.6 kW and operating at 30 kHz, are provided in this paper to verify the performance of this new family of converters.     

Analysis,design and implementation of an interleaved three-level PWM DC/DC ZVS converter

This paper presents a new parallel three-level soft switching pulse-width modulation (PWM) converter. The proposed converter has two circuit cells operated by the interleaved PWM modulation. Thus, the ripple currents at input and output sides are reduced. Each circuit cell has two three-level zero voltage switching circuits sharing the same power switches. Therefore, the current and power rating of the secondary side components are reduced. Current double rectifier topology is selected on the secondary side to decrease output ripple current. The main advantages of the proposed converter are soft switching of power switches, low ripple current on the output side and low-voltage rating of power switches for medium-power applications. Finally, the performance of the proposed converter is verified by experiments with 1 kW prototype circuit.     

Novel zero-voltage and zero-current-switching (ZVZCS) full-bridge PWM converter using coupled output inductor

A novel zero-voltage and zero-current-switching (ZVZCS) full-bridge pulse-width-modulated (PWM) converter is proposed to improve the previously proposed ZVZCS full-bridge PWM converters. By employing a simple auxiliary circuit with neither lossy components nor active switches, soft-switching of the primary switches is achieved. The proposed converter has many advantages such as simple auxiliary circuit, high efficiency, low voltage stress of the rectifier diode and self-adjustment of the circulating current, which make the proposed converter attractive for the high voltage and high power applications. The principles of operation and design considerations are presented and verified on the 4 kW experimental converter operating at 80 kHz.     

Resonant link bidirectional power converter. I. Resonant circuit

This paper proposes a novel resonant circuit capable of PWM operation with zero switching losses. The resonant circuit is aimed at providing zero voltage intervals in the DC link of the PWM converter during the required converter device switching periods, and it gives minimum DC bus voltage stresses and minimum peak resonant current. It requires only two additional switches compared to a conventional PWM converter. It is observed that the resonant circuit guarantees the soft switching of all the switching power devices of converters including the switches for resonant operation. Simulation results and experimental results are presented to verify the operating principles     

Analysis, designing, and experimentation of a transformer-assistedPWM zero-voltage switching pole inverter

This paper proposes a transformer-assisted pulsewidth modulation (PWM) zero-voltage switching pole inverter. As the auxiliary-resonant-commutated pole inverter (ARCPI), the proposal guarantees zero-voltage switching of the main switch and zero-current switching of the auxiliary switch, with a small power auxiliary circuit and full PWM capability. In particular, problems outstanding with the ARCPI such as control complexity, auxiliary switch protection, and center-tap potential variation, etc., are solved in the proposal. The commutation process is discussed step by step in the paper. A detailed analysis for the auxiliary circuit with regard to commutation duration/duty-cycle limitation, auxiliary switch peak current/RMS current, resonant capacitor RMS current, as well as pole output voltage loss are presented afterwards. A design methodology for the auxiliary circuit is recommended based on the analysis. The proposal is experimentally verified with a 4.25 kW half-bridge inverter prototype     

A zero-voltage-switched PWM boost converter with an energyfeedforward auxiliary circuit

A zero-voltage-switched (ZVS) pulsewidth-modulated (PWM) boost converter with an energy feedforward auxiliary circuit is proposed in this paper. The auxiliary circuit, which is a resonant circuit consisting of a switch and passive components, ensures that the converter's main switch and boost diode operate with soft switching. This converter can function with PWM control because the auxiliary resonant circuit operates for a small fraction of the switching cycle. Since the auxiliary circuit is a resonant circuit, the auxiliary switch itself has both a soft turn on and turn off, resulting in reduced switching losses and electromagnetic interference (EMI). This is unlike other proposed ZVS boost converters with auxiliary circuits where the auxiliary switch has a hard turn off. Peak switch stresses are only slightly higher than those found in a conventional PWM boost converter because part of the energy that would otherwise circulate in the auxiliary circuit and drastically increase peak switch stresses is fed to the load. In this paper, the operation of the converter is explained and analyzed, design guidelines are given, and experimental results obtained from a prototype are presented. The proposed converter is found to be about 2%-3% more efficient than the conventional PWM boost converter     

一种新颖的ZVZCS双管正激变换器

本文提出了一种新颖的、利用辅助电路实现零电压、零电流开关的双管正激变换器。其中,有源钳位辅助电路用来实现主开关管上的零电压开通,同时使该变换器的占空比拓展到50%以上;变压器副边的辅助电路用来实现主开关管以及副边二极管的零电流关断。因此,该变换器中全部开关管均工作在软开关状态下。与其他软开关双管正激变换器相比,该变换器具有结构简单、所用元器件最少等优点。最后,经过一台250W的样机检验,该变换器效率最高可达95.7%,非常适合IGBT应用的场合。     

一种新型软开关DC-DC PWM升压变换器设计

为提高转换效率并降低电源开关的电流应力,提出一种基于新型有源缓冲电路的PWM DC-DC升压变换器。该有源缓冲电路使用ZVT—ZCT软开关技术,分别提供了总开关ZVT开启及ZCT闭合、辅助开关ZCS开启及ZCT闭合。消除了总开关额外的电流及电压应力,消除了辅助开关电压应力,且有源缓冲电路的耦合电感降低了电流应力。另外,通过连续将二极管添加到辅助开关电路,防止来自共振电路的输入电流应力进入总开关。实验结果表明,相比传统的PWM变换器,新的DC-DC PWM升压变换器在满负荷时电流应力降低且总体效率能达到98.7%。     

A novel ZVS DC/DC converter for high power applications

This paper presents a novel zero voltage switch (ZVS) pulse-width modulation (PWM) DC/DC converter for high power, high output voltage applications. By using two active switches in the secondary side of a transformer, the proposed converter achieves not only ZVS of the active switches in the entire load ranges but also soft commutation of the output rectifier diodes. The proposed topology has simple structure and control strategy. Simulation results and experimental results of a 2.8 kW 200 kHz DC/DC converter are presented.     

Three-level LLC series resonant DC/DC converter

Paper presents a three-level soft switching LLC series resonant dc/dc converter. Zero-voltage switching (ZVS) is achieved for each main switch without any auxiliary circuit. Voltage stress of each main switch is half of input voltage. Zero-current-switching (ZCS) is achieved for rectifier diodes. Wide input/output range can be achieved under low frequency range because of two-stage resonance. Only one magnetic component is required in this converter. Efficiency is higher in high line input, so this converter is a preferable candidate for power products with the requirement of hold up time. For design convenience, relationship between dc gain and switching frequency, load resistance is deduced. Its open load characteristic and short load characteristic are exposed to provide theory basis for no load operation and over current protection. Design consideration of four dead times is presented to assure that voltage stress for main switches is within half of input voltage and ZVS for each main switch is achieved. Finally the principle of operation and the characteristics of the presented converter are verified on a 500V-700V input 54V/10A output experimental prototype, whose efficiency reaches 94.7% under rating condition.     

单相全桥三电平节能逆变器

随着开关频率的提高,单相全桥逆变器处于硬开关切换时的开关损耗也会明显增大,将导致逆变器处于低效率运行.为解决这一问题,提出了一种单相全桥三电平节能逆变器.通过设置辅助换流电路,利用谐振使主开关并联的电容的电压下降到零,主开关可实现零电压切换,而且在换流过程中,两组双向辅助开关可分别实现零电压切换和零电流切换.分析了电路的工作状态,实验结果表明主开关和辅助开关都能实现软切换.因此该单相全桥三电平逆变器可实现高效率运行.     

A New Family of Zero-Current-Switching (ZCS) PWM Converters

A new family of zero-current-switching (ZCS) pulsewidth-modulated (PWM) converters which uses a new ZCS-PWM switch cell is presented in this paper. The main switch and auxiliary switch operate at ZCS turn-on and turn-off, and all the passive semiconductor devices in the ZCS-PWM converter operate at zero-voltage-switching (ZVS) turn-on and turn-off. Besides operating at constant frequency and with reduced commutation losses, these new converters have no additional current stress in comparison to the hard-switching converter counterpart. The new family of ZCS-PWM converters is suitable for high-power applications using insulated gate bipolar transistors (IGBTs). The PWM switch model and state-space averaging approach is used to estimate and examine the steady-state and dynamic character of the system. The principle of operation, theoretical analysis, and experimental results of the new ZCS-PWM boost converter, rated 1 kW and operating at 30 kHz, are provided in this paper to verify the performance of this new family of converters.     

A New PWM-Controlled Quasi-Resonant Converter for a High Efficiency PDP Sustaining Power Module

A new pulsewidth modulation (PWM)-controlled quasi-resonant converter for a high-efficiency plasma display panel (PDP) sustaining power module is proposed in this paper. The load regulation of the proposed converter can be achieved by controlling the ripple of the resonant voltage across the primary resonant capacitor with a bidirectional auxiliary circuit, while the main switches are operating at a fixed duty ratio and fixed switching frequency. Hence, the waveforms of the currents can be expected to be optimized from the view-point of conduction loss. Furthermore, the proposed converter has good zero-voltage switching (ZVS) capability, simple control circuits, no hign-voltage ringing problem of rectifier diodes, no dc offset of the magnetizing current and low-voltage stresses of power switches. Thus, the proposed converter shows higher efficiency than that of a half-bridge LLC resonant converter under light load condition. Although it shows the lower efficiency at heavy load, because of the increased power loss in auxiliary circuit, it still shows the high efficiency around 94%. In this paper, operational principles, features of the proposed converter, and analysis and design considerations are presented. Experimental results demonstrate that the output voltage can be controlled well by the auxiliary circuit using the PWM method.      

有源箝位软开关充电机的设计与仿真研究

传统硬开关电路影响效率和可靠性的同时,对其他设备的电磁干扰也较大,软开关则可解决上述问题。本文提出了一种基于辅助谐振换流的新型ZVT-PWM变换器,即通过采用简单的有源辅助谐振网络实现了主、辅开关管的软开关,主开关管实现了零电压开通,开关管电流电压应力小。利用这种软开关技术研制了一台用于为风力发电蓄电池充电的充电机,给出了充电机的控制系统框图,简单介绍了充电机的工作原理。最后利用Pspice给出了运行波形和仿真结果。