Graft copolymerzation of poly(vinyl chloride) with styrene. I. Synthesis and characterization

Graft copolymerization of poly(vinyl chloride) (PVC) partially dehydrochlorinated by heating in nitrobenzene was investigated using styrene as monomer and anhydrous AlCl₃ as cationic initiator in the temperature range of 0–35°C. Effect of monomer, catalyst, and PVC concentration on % graft-on was also evaluated. Introduction of labile sites in PVC by partial dehydrochlorination in nitrobenzene resulted in an increase in % graft-on. Intrinsic viscosity of PVC–g–polystyrene in THF initially increased with an increase in % graft-on. At higher % graft-on a decrease in [η] was observed.     

Grafting of vinyl acetate onto poly(vinyl chloride) in solution

Radiation-induced grafting of vinyl acetate (VAc) onto poly(vinyl chloride) (PVC) was performed in solution with dimethylformamide (DMF). Grafting was studied as a function of dose, dose rate, and VAc/PVC ratio. The amount of grafting was measured by IR spectroscopy on the graft copolymer fraction insoluble in hot methanol. The homopolymerization of VAc was also studied in the same conditions, in order to check the influence of the solvent on radiochemical reactions leading to graft copolymers. The results show that the grafting can be easily obtained and the graft copolymer will be tested for the preparation of ultrafiltration membranes.     

Effect of compatibility between solvent and poly(vinyl chloride) on dechlorination of poly(vinyl chloride)

In this study, the use of diethylene glycol (DEG), triethylene glycol (TEG), n-C₁₀H₂₁OH, and ethylene glycol (EG) as solvents for NaOH in the dechlorination of poly(vinyl chloride) (PVC) was investigated. In the early reaction time, the degrees of dechlorination for DEG, TEG, and n-C₁₀H₂₁OH were notably higher than that for EG. Further, the high compatibility between PVC and the solvents was considered to result in the easy penetration of the solvent and OH⁻ into PVC particles, leading to the acceleration of dechlorination in the early reaction stage. An improvement of the dechlorination was actually observed for DEG and TEG compared with EG. The solvent with the best compatibility to PVC, n-C₁₀H₂₁OH, however, showed little improvement due to the formation of a protective polyene layer on the surface of the PVC particles.     

Chlorinated atactic polypropylene as a plasticizer for poly(vinyl chloride)

Atactic polypropylene, a byproduct obtained in the manufacture of isotactic polypropylene, has been chlorinated under various reaction conditions. The chlorination reaction is reasonably fast so as to give a product of 53-43% chlorine content in 3 h. The chlorinated product has been incorporated in poly(viny1 chloride) formulations with a view to study its plasticizing activity. Generally this type of compound acts only as a secondary plasticizer; hence it has been used in combination with di(2-ethylhexyl)phthdate, a primary plasticizer. Different proportions of these two plasticizers have been added to poly(vinyl chloride) resin to obtain a series of formulations. These compounds were evaluated, and it appears that the addition of chlorinated atactic polypropylene (APPC) helps in easy processing and increases the throughput. The increasing concentration of APPC showed an upward trend in die head pressure and torque indicating an increase in melt viscosity. The results of physical properties evaluation show that APPC acts as a reinforcing agent and also imparts permanence to the plasticizers.     

Synthesis and characterization of a mass polymerized impact modified poly (vinyl chloride) resin

Rigid homopolymer PVC has many uses and has two disadvantages usually compensated for by additives. One difficulty is processability handled by processing aids and the other is an inherent low impact strength increased by impact modifier compounding. This paper describes graft-copolymerized vinyl chloride on rubber-type polyolefins which give better processability and greatly improved impact resistance.     

Synthesis of poly(vinyl benzal) from poly(vinyl alcohol) in nonaqueous medium

Poly(vinyl alcohol) (PVA) is soluble only in water and so some important derivatives like esters cannot be prepared from PVA. The 100% conversion of PVA to acetal is also elusive as there is strong intermolecular and intramolecular hydrogen bonding. However, PVA can be dissolved in a nonaqueous medium in the presence of a small amount of C₂H₅NO₃ · DMSO(EN · DMSO) and so a maximum extent of conversion may be possible. Here, we report the preparation of poly(vinyl benzal) (PVB) by acid-catalyzed homogeneous acetalization of PVA with benzaldehyde in a nonaqueous medium. The formation of PVB was confirmed by IR and ¹H-NMR spectra. The molecular mass of the polymer was determined by the GPC method. The PVB prepared had a degree of acetalization of 95 mol%. The glass transition temperature, T_g was measured from differential scanning calorimetric (DSC) thermograms. Thermal stabilities were checked by thermogravimetric analysis (TGA) and differential thermogravimetry (DTG). A possible mechanism of three-step thermal decomposition of PVB is proposed. © 1996 John Wiley & Sons, Inc.     

聚（苯乙烯－丙烯酰胺）三氯化钕配合物的制备

合成了聚（苯乙烯－丙烯酰胺）三氯化钕配合物（ＳＡＡ·ＮｄＣｌ３），高分子链上的功能团是通过羧基氧原子与稀土离子配位的。     

Experimental investigations of polypropylene and poly(vinyl chloride) composites filled with plerospheres

Plerospheres, defined here as superfine spherical particles (0.5–5 μm) separated from fly ash (rather than as other solid spherical particles, as some have used the term), are separated from coal fly ash but are dramatically different from it. Plerospheres can be used as polymer fillers to improve the properties of composites. With plerospheres used as fillers for polypropylene (PP) and unplasticized poly(vinyl chloride) (UPVC), the effects of the filler content, the particle sizes of the plerospheres, and the coupling agent on the composite properties were studied. The particle sizes of the plerospheres were 2 and 5 μm. The results suggested that the notched impact properties both at a normal temperature and a low temperature and the tensile and flexural properties of plerosphere/PP increased significantly when the content was increased from 0 to 30 wt % and further increased with the addition of a coupling agent. Differential scanning calorimetry indicated that the thermal properties of the plerosphere/PP composite improved. The surface characteristics and morphology of the impact fracture surface were examined in detail with scanning electron microscopy. The rheological performance of plerosphere/UPVC pipe composites obviously improved; the plasticizing time was shortened, and the maximum torque was reduced. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 126–131, 2004     

Synthesis and characterization of poly(vinyl carbazole) complexes with copper(II) chloride in THF solution

Several polymer-metal complexes were prepared by reacting poly(vinyl carbazole) (PNVC) with copper(II) chloride, CuCl₂.2H₂O, in refluxing tetrahydrofurane (THF) for mole ratios of CuCl₂.2H₂O to monomeric unit (Cu:PNVC ratio) ranging between 0.086 and 4.98. Complexes were characterized by infrared (IR) and elemental analysis. Thermal behavior of complexes was studied by differential thermal analysis (DTA). It appears that THF behaves as a specific solvent for complexation of PNVC with copper(II) chloride.     

Modification of polypropylene through intercrosslinking graft copolymerization of poly(vinyl alcohol): Synthesis and characterization

Modification of polypropylene (PP) has been successfully carried out through intercrosslinking of poly(vinyl alcohol) (PVA), by chemical graft copolymerization method using benzoyl peroxide (BPO) as radical initiator. Prior to grafting, PP was irradiated by gamma rays at a constant dose rate of 3.40 kGy/h to introduce hydroperoxide groups. Optimum conditions pertaining to maximum percentage of grafting were evaluated as a function of different reaction parameters. Maximum percentage ofgrafting of PVA (75%) was obtained at [BPO] = 5.51 × 10^?2 mol/L in 120 min at 70°C using 15 mL of water. Characterization of pristine PP and PP‐g‐PVA was carried out by FTIR, thermogravimetric analysis, and scanning electron micrography. Swelling studies were carried out in pure, binary, ternary, and quaternary solvent systems comprising of water, ethanol (EtOH), dimethylsulfoxide (DMSO) and N, N‐dimethylformamide (DMF) in different ratios. Maximum swelling values of PP‐g‐PVA (both composite and true graft) was observed in pure DMSO followed by DMF, EtOH, and water and it was also higher than that observed in mixed solvent system. Water retention studies of pristine PP and PP‐g‐PVA (both composite and true graft) were investigated at different time periods, temperature, and pH. Maximum % water retention of PP‐g‐PVA (composite) (108%) was observed in 8 h at 50°C in neutral medium (pH = 7). © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Preparation and structural characterization of nanocrystalline poly(vinyl chloride)

This article describes the development of novel nanocrystalline poly(vinyl chloride) (PVC) for potential applications in PVC processes and reports improvements in the mechanical properties and thermal resistance. Before the preparation of nanocrystalline PVC via jet milling, PVC was spray‐treated and heat‐treated to improve its crystallinity. The pulverization and degradation, morphology, crystalline structure, and melting‐point changes of postmodified PVC during jet milling and the relationship between the distributions of the particle size and processing temperature were investigated. X‐ray analysis and density testing indicated increased density and improved crystallinity. The crystalline region of nanocrystalline PVC was less than 80 nm, with a particle size distribution of 5–20 μm and a melting point of less than 128°C. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 563–569, 2004     

梳型接枝PVC的制备

研究了聚氯乙烯与肉豆蔻酸钠的接枝反应,并制备梳形接枝PVC。利用FT-IR、1H-NMR对梳型接枝PVC的结构进行表征,并探讨反应条件对接枝率的影响。结果表明,梳形侧链成功接枝到PVC上,且在反应温度70℃、反应时间9h、单体用量50%时,接枝率最高。     

The solubility of vinyl chloride in poly(vinyl chloride)

The solubility of vinyl chloride monomer (VCM) in PVC powders has been studied by equilibrium vapor pressure and microbalance gravimetric techniques at temperatures from 30 to 110°C. At temperatures and VCM concentrations above the glass transition, the solubility closely follows the Flory-Huggins equation with χ = 0.98 and is independent of temperature and of the PVC type, molecular weight, or history. In the glassy state, the VCM solubility is higher than the Flory-Huggins value and shows pronounced dependence upon time and the PVC history. These results have been interpreted through the dual-mode sorption concept of Michaels, Vieth, and Barrie: Normal dissolution follows the Flory-Huggins relation, and the additional glassy-state solubility represents the contribution of a hole-filling process. Changes in solubility with time and sample history parallel well-known volume relaxation processes, indicating that vapor solubility measurements offer a direct and sensitive measure of the free-volume state of glassy polymers.     

Solubility of vinyl chloride in poly (vinyl chloride) in a water slurry

The solubility of vinyl chloride (VCM) vapor in poly (vinyl chloride) (PVC) in a water slurry has been measured between 55 and 65°C. The heat and entropy of sorption were shown to be very close to those of condensation. The solubilities measured in this study were higher than those obtained in other studies on dry PVC and PVC latex. The interaction parameter (x) in the Flory-Huggins equation has been shown to vary between 0.34 and 0.61 over the composition range studied. The effect of ageing the slurry in the presence of VCM is also discussed.     

Graft copolymerization of poly(vinyl chloride) with styrene. II. Thermal behavior

Thermal behavior of graft copolymers of polyvinyl chloride with polystyrene prepared by using a cationic initiator (AlCl₃) was evaluated by measurement of rates of dehydrochlorination in nitrogen atmosphere. With increase in the extent of grafting the rates were found to decrease. Dynamic thermogravimetric analysis revealed an overall improvement in thermal stability of copolymers. Development of polyene sequences in degraded polymer samples was evaluated by measurement of electronic absorption spectra. In comparison to PVC, graft copolymer samples had fewer conjugated double bonds.     

Grafting of polypropylene with N-cyclohexylmaleimide and styrene simultaneously using supercritical CO2

Monomer mixture of styrene (St) and N-cyclohexylmaleimide (ChMI) and initiator benzoyl peroxide (BPO) were first impregnated into isotactic polypropylene (iPP) films simultaneously using supercritical carbon dioxide (SC CO₂) as a solvent and swelling agent at 35.0 °C. The composites were obtained after the monomers were grafted onto the iPP matrix at 70 °C. The effects of various conditions, such as pressure, monomer concentration, and the molar ratio of the two monomers in the soaking process, on the composition of the composites were determined. The molar ratios of St to ChMI in the composites were estimated by Fourier transform infrared spectroscopy. The thermal properties, the morphology, and the mechanical properties of the composites were characterized by different techniques. The results demonstrated that the phase size of the grafted St-ChMI was very small and the phase boundary was very ambiguous. The composites had better thermal stability than the original iPP film. The Young's modulus and tensile strength of the film increased continuously with increasing grafting percentage. The two grafted monomers in the composites had good synergetic effect.     

Blends of polypropylene with poly(vinyl butyral)

The thermal stability, crystallization behavior, and morphology of poly(vinyl butyral) (PVB) with differing compositions of vinyl alcohol and butyral units were investigated. It was found that the glass‐transition temperature of PVB decreases with increasing concentration of butyral units, mainly because of the reduced number of hydrogen bonds between hydroxyl groups of the chains. PVB samples with high vinyl alcohol content (≥63.3% by weight) are crystallizable and present an endothermic melting peak in the range 170–220°C. The thermal stability of PVB is also influenced by composition and increases with the number of butyral units. The thermal and crystallization characteristics of PVB were compared with those of neat polyvinyl alcohol (PVA), and the differences explained in terms of molecular structure. Two amorphous PVB samples, containing 31 and 14 wt % of vinyl alcohol units, respectively, were blended with isotactic polypropylene grafted with maleic anhydride (PP–MA), the latter of which was present to favor compatibilization of the components through chemical reaction or dipolar interactions involving the anhydride groups of the PP–MA and the hydroxyl groups of PVB. Properties of PP–MA/PVB 90/10 blends, prepared by melt extrusion, were compared to those of neat PP–MA. Both the PVBs used were immiscible with PP–MA, as indicated by the invariance of glass‐transition temperatures with the composition of the blends. However, a high level of compatibility between the components was achieved because the blends showed good mechanical properties that were comparable to, or even superior to, those of neat PP–MA. The analysis of the crystallization kinetics, performed both in isothermal and nonisothermal modes, showed that crystallization of polypropylene is only slightly influenced by the presence of the PVB phase. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 2934–2946, 2001     

On the stereochemical composition of poly(vinyl chloride) (PVC) and polypropylene (PP): a phenomenological study

The number of mmr‐ and rrm‐based structures which occur necessarily whenever an isotactic or a syndiotactic sequence breaks off respectively; the extent to which they are isolated or are extended to atactic sequences, and the fact that the mmr repeating sequence, especially when it takes the GTTG^?TT conformation, is shorter and exhibits greater local free volume than rrm, mmm and rrr sequences, are shown to be the stereochemical composition determining structures in poly(vinyl chloride) (PVC) and polypropylene (PP) polymers. These structures, as analyzed by ¹³C NMR spectroscopy and probability calculations, have been determined as a function of the overall tacticity for one series of samples prepared by bulk polymerization at temperatures varying from ?50 °C to 70 °C, and one series of samples prepared by polarity‐based fractionation of a commercial polymer. Using this approach, the stereochemical composition of the samples could be identified. The results are of interest to understand the changes in the physical properties as shown in earlier and current work for both series of polymers. © 2003 Society of Chemical Industry     

Thermal characterization of poly(vinyl chloride) samples prepared by living radical polymerization: Comparison with poly(vinyl chloride) prepared by free radical polymerization

Poly(vinyl chloride) (PVC) samples were synthesized by a living radical polymerization (LRP) method and compared with commercial PVC prepared by the conventional free radical polymerization (FRP). The differences were assessed, for the first time, in terms of viscosimetry parameters and thermal analysis. The LRP method used to prepare the PVC‐LRP samples is the only one available to obtain this polymer free of structural defects, being of commercial interest in a view of preparing a new generation of PVC‐based polymer with outstanding performance. The polymerization temperature selected (35°C) to prepare the LRP samples is currently used in the industry to prepare PVC‐FRP grades with moderate to high molecular weight. Since the thermal stability is a direct consequence of the polymer structure, this study is of vital importance to understand the potential of new PVC‐LRP. The thermoanalytical measurements demonstrate an enhanced thermal stability of PVC‐LRP when compared with its FRP counterpart. The PVC‐LRP sample with very low molecular weight reveals a higher thermal stability than the most stable PVC‐FRP sample. It is the first report dealing with thermal analysis of PVC prepared by LRP. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008