Synthesis and properties of (BaxPb1−x)(Zn1/3Nb2/3)O3 relaxor ferroelectric ceramics using a reaction-sintering process

(Ba_xPb_1−x)(Zn_1/3Nb_2/3)O₃ (BPZN; x = 0.06–0.1) relaxor ferroelectric ceramics produced using a reaction-sintering process were investigated. Without any calcination involved, the mixture of raw materials was pressed and sintered directly. BPZN ceramics of 100% perovskite phase were obtained. Highly dense BPZN ceramics with a density higher than 98.5% of theoretical density could be obtained. Maximum dielectric constant K_max 13,500 (at 75 °C), 19,600 (at 50 °C) and 14,800 (at 28 °C) at 1 kHz could be obtained in 6BPZN, 8BPZN and 10BPZN, respectively. Dielectric maximum temperature (T_max) in BPZN ceramics via reaction-sintering process is lower than BPZN ceramics prepared via B-site precursor route.     

Dielectric and ferroelectric properties of Ba0.8Sr0.2Ti1−5x/4NbxO3 ceramics

Ba_0.8Sr_0.2Ti_1−5x/4Nb_xO₃ ceramics, x = 0, 0.01, 0.05, 0.10, were fabricated by conventional solid-state reaction. With increasing niobium content the ferroelectric phase transition temperature decreases linearly, and the dispersivity of the transition increases. Niobium B-site decreases transition temperature more pronounced than Sr²⁺ at A-site. The heterovalent substitution of Nb⁵⁺ in low content causes local defect dipole, while more substitutions introduce disorder to disturb the long-range dipole correlation. Ba_0.8Sr_0.2Ti_1−0.5/4Nb_0.1O₃ ceramic shows weak ferroelectric loop at room temperature far from its transition temperature, 153 K.     

Solubility limits and microwave dielectric properties of Ba6−3xSm8+2xTi18O54 solid solution

Upper and lower solubility limits in Ba_6−3xSm_8+2xTi₁₈O₅₄ tungsten bronze ceramics were determined by Rietveld refinement of XRD data combined with backscattered electron images, and the variation tendency of microwave dielectric characteristics was also investigated. The upper solubility limit was confirmed as x = 2/3, while the lower solubility limit was determined as 1/4 instead of the previously reported one x = 3/10. The dielectric constant of Ba_6−3xSm_8+2xTi₁₈O₅₄ ceramics decreases monotonically with increasing x, while the small temperature coefficient of resonant frequency with complex variation tendency is observed for the compositions 1/2 ≤ x ≤ 4/5. The Qf value increases at first, reaches the maximum around x = 2/3, and turns to decrease for x > 7/10.     

Influence of A-site Ba substitution on microwave dielectric properties of (BaxMg1−x)(A0.05Ti0.95)O3 (A=Zr,Sn) ceramics

The microwave dielectric properties of (Ba_xMg_1−x)(A_0.05Ti_0.95)TiO₃ (A=Zr, Sn) ceramics were investigated with regard to substitution of Ba for Mg of A-site. The microwave dielectric properties were correlated with the Ba content. With an increase in Ba content from 0.01 to 0.1, the dielectric constant and the τ_f value increased, but the Q×f value decreased. The sintered (Ba_xMg_1−x)(Zr_0.05Ti_0.95)TiO₃ (called B_xMZT) ceramics had a permittivity in the range of 19.1−20.6, quality factor from 180,000 to 25,000 GHz, and variation in temperature coefficient of resonant frequency from −35 to −39 ppm/°C with increasing composition x. For sintered (Ba_xMg_1−x)(Sn_0.05Ti_0.95)TiO₃ (called B_xMST) ceramics, the dielectric constant increased from 19 to 20.5, Q×f value increased from 120,000 to 37,000 (GHz), and the τ_f value increased from −50 to −3.3 ppm/°C as the x increased from 0.01 to 0.1. When A=Sn and x=0.1, (Ba_0.1Mg_0.9)(Sn_0.05Ti_0.95)TiO₃ ceramics exhibited dielectric constant of 20.5, Q×f value of 37,000 (GHz), and a near-zero τ_f value of −3.3 ppm/°C sintered at 1210 °C for 4 h.     

Dielectric properties of Sm, Nd and Fe doped Bi1.5Zn0.92Nb1.5O6.92 pyrochlores

New pyrochlore ceramics have been produced by doping Sm and Nd into the Bi site and Fe into the Nb site in the Bi_1.5Zn_0.92Nb_1.5O_6.92 (BZN) pyrochlore. Doped pyrochlore ceramics were produced by conventional solid state mixing of oxides at different doping levels using the compositions of Bi_1.5−xSm_xZn_0.92Nb_1.5O_6.92, Bi_1.5−xNd_xZn_0.92Nb_1.5O_6.92 and Bi_1.5Zn_0.92Nb_1.5−xFe_xO_6.92−x. The solubility limit of cations was determined as x = 0.13, 0.18 and 0.15 for Sm, Nd and Fe, respectively. While Sm and Nd increased the dielectric constant (?), Fe doping led a decrease in ?. Dielectric constant of Sm and Nd doped BZN increased to 199 at x = 0.13 (Sm) and to 219 at x = 0.18 (Nd). At low Fe dopings (x = 0.05), the dielectric constant of BZN increased to 242 but decreased to 211 at x = 0.15. The dielectric losses were lower for Sm and Nd dopings than Fe but in all cases it was lower than 0.006. The dielectric constant of Sm, Nd and Fe doped BZN ceramics was nearly independent of frequency within the frequency range between 1 kHz and 2 MHz, but decreased considerably with temperature between 20 and 200 °C. Temperature coefficient of Sm doped BZN (−354 ppm/°C) was lower than Nd and Fe doped BZN ceramics at solubility limits (−538 ppm/°C for Nd and −565 ppm/°C for Fe).     

Adjustable dielectric properties of Li2CuxZn1−xTi3O8 (x=0 to 1) ceramics with low sintering temperature

Single-phase dielectric ceramics Li₂Cu_xZn_1−xTi₃O₈ (x=0–1) were synthesized by the conventional solid-state ceramic route. All the solid solutions adopted Li₂MTi₃O₈ cubic spinel structure in which Li/M and Ti show 1:3 order in octahedral sites whereas Li and M are distributed randomly in tetrahedral sites with the degree of Li/M cation mixing varying from 0.5 to 0.3. The substitution of Cu for Zn effectively lowered the sintering temperatures of the ceramics from 1050 to 850 °C and significantly affected the dielectric properties. As x increased from 0 to 0.5, τ_f gradually increased while the dielectric constant (ε_r) and quality factor value (Q×f) gradually decreased, and a near-zero τ_f of 1.6 ppm/°C with ε_r of 25.2, Q×f of 32,100 GHz could be achieved for Li₂Cu_0.1Zn_0.9Ti₃O₈ ceramic sintered at 950 °C, which make it become an attractive promising candidate for LTCC application. As x increases from 0.5 to 1, the dielectric loss significantly increases with AC conductivity increasing up to 2.3×10⁻⁴ S/cm (at 1 MHz).     

Investigation of ternary system Pb(Sn,Ti)O3-Pb(Mg1/3Nb2/3)O3 with morphotropic phase boundary compositions

(1 − x)Pb(Sn_1−yTi_y)O₃-xPb(Mg_1/3Nb_2/3)O₃ (x = 0.1-0.4, y = 0.45-0.65) ternary system was prepared using two-step columbite precursor method. Phase structure of the synthesized ceramics was studied by using X-ray powder diffraction and the morphotropic phase boundary (MPB) curve of the ternary system was confirmed. The isothermal map of Curie temperature (T_C) in the phase diagram was obtained based on the dielectric-temperature measurements. The coercive field E_C and internal bias field E_i were found to increase with increasing PT content, while decrease with increasing PMN content. The optimum properties were achieved in the MPB composition 0.8Pb(Sn_0.45Ti_0.55)O₃-0.2Pb(Mg_1/3Nb_2/3)O₃, with dielectric permittivity ?_r, piezoelectric coefficient d₃₃, planar electromechanical coupling k_p, mechanical quality factor Q_m and T_C of being on the order of 3040, 530pC/N, 55.5%, 320 and 190 °C, respectively, exhibiting potential usage for high power application.     

Fabrication and characterisation of Cr and Co doped Bi1.5Zn0.92Nb1.5O6.92 pyrochlores

Cr and Co doped Bi_1.5Zn_0.92Nb_1.5O_6.92 pyrochlore ceramics were produced by solid state mixing of oxides. Cr and Co were doped into the Nb and Nb-Zn sites considering the compositions of Bi_1.5Zn_0.92Nb_1.5−xCr_xO_6.92−x, (Bi_1.5Zn_0.46)(Zn_0.46−3x/6Nb_1.5−3x/5Cr_x)O_6.92−x/2 for Cr doping and Bi_1.5Zn_0.92Nb_1.5−3x/5Co_xO_6.92, (Bi_1.5Zn_0.46)(Zn_0.46−3x/6Nb_1.5−3x/5Co_x)O_6.92−x/2 for Co doping. The solubility limit of Cr in BZN was higher than that of Co and the solubility limit increased when doping was made both into Nb and Zn sites. The second phases appeared when x > 0.2 for Cr and x > 0.15 for Co doping into the Nb-Zn sites. Simultaneous Cr doping into the Nb- and Zn-sites of BZN pyrochlore gave higher dielectric constant than doping into the Nb-site of pyrochlore. However, Co doping into the Nb- and Zn-sites and only into the Nb-site of BZN gave identical dielectric results in the range of 202-218. The temperature coefficient of dielectric constant decreased with Cr doping and increased with Co doping.     

Effects of Al2O3 addition on the microstructure and microwave dielectric properties of Ba4Nd9.33Ti18O54 ceramics

Ba₄Nd_9.33Ti₁₈O₅₄·x wt%Al₂O₃ (BNT-A) ceramics (x=0, 0.5, 1.0, 1.5, 2.0, 2.5) were prepared by the conventional solid state reaction. The effects of Al₂O₃ on the microstructure and microwave dielectric properties of Ba₄Nd_9.33Ti₁₈O₅₄ (BNT) ceramics were investigated. X-ray diffraction and backscatter electronic images showed that the Al₂O₃ additive gave rise to a second phase BaAl₂Ti₅O₁₄ (BAT). The formation mechanism and grain growth of the BAT phase were first discussed. Dielectric property test revealed that the Al₂O₃ additive had improved the dielectric properties of the BNT ceramics: increased the Q×f value from 8270 to 12,180 GHz and decreased the τ_f value from 53.4 to 11.2 ppm/°C. A BNT-A ceramic with excellent dielectric properties: ε_r=70.2, Q×f=12,180 GHz, τ_f=20 ppm/°C was obtained with 2.0 wt% Al₂O₃ added after sintering at 1320 °C for 4 h.     

Effect of Ti substitution for Nb in double perovskite-type Ba3CaNb2O9 on chemical stability and electrical conductivity

This paper reports the synthesis, structure, chemical stability and electrical transport properties of Ti substituted Ba₃CaNb₂O₉ (BCN) to develop electrolytes for proton conducting solid oxide fuel cells (H-SOFCs). The powder X-ray diffraction (PXRD) of Ba₃CaNb_2−xTi_xO_9−δ (x = 0.1, 0.15, 0.2, 0.25 and 0.3) and Ba₃Ca_1.18Nb_1.82−xTi_xO_9−δ (x = 0.15 and 0.25) showed formation of double perovskite-like structure with lattice constant comparable to that of Ba₃Ca_1.18Nb_1.82O_9−δ (BCN18). Scanning electron microscopy (SEM) showed dense and pore-free microstructure for Ba₃CaNb_1.75Ti_0.25O_8.875. PXRD and Fourier transform infrared (FTIR) spectroscopy data confirmed long-term stability of Ba₃CaNb_2−xTi_xO_9−δ and Ba₃Ca_1.18Nb_1.82−xTi_xO_9−δ in boiling H₂O and in CO₂ at elevated temperatures. The AC impedance investigation showed contribution due to bulk, grain-boundary and electrode effect at low temperatures. The electrical conductivity of studied materials were measured in different medium including dry air, dry H₂, wet H₂, wet N₂ and D₂O. Increase in conductivity in wet N₂ and decrease in conductivity in D₂O confirmed the proton conduction in Ba₃CaNb_1.75Ti_0.25O_9-δ. Among Ti-substituted compounds investigated in this study, Ba₃Ca_1.18Nb_1.57Ti_0.25O_8.605 showed the highest conductivity of 3.5 × 10⁻⁴ S cm⁻¹ at 400 °C in wet N₂ (3%H₂O), which is comparable to reported values of Ba₂Ca_0.79Nb_0.66Ta_0.55O_6−δ and BCN18.     

Enhanced ferroelectric properties in (Ba1−xCax)(Ti0.94Sn0.06)O3 lead-free ceramics

Lead-free (Ba_1−xCa_x)(Ti_0.94Sn_0.06)O₃ (BCST) (x = 0.01-0.04) ceramics were prepared using a solid-state reaction technique. The effects of Ca content on the phase structure and electrical properties of the BCST ceramics were investigated. High piezoelectric coefficient of d₃₃ = 440 pC/N, planar electromechanical coupling factor of k_p = 45% and dielectric constant ?_r = 6900 were obtained for the samples at x = 0.03. At room temperature, a polymorphic phase transition (PPT) from orthorhombic phase to tetragonal phase was identified in the composition range of 0.02 < x < 0.04.     

Microstructures and dielectric properties of spark plasma sintered Ba0.4Sr0.6TiO3/CaCu3Ti4O12 composite ceramics

(1 − x)Ba_0.4Sr_0.6TiO₃/xCaCu₃Ti₄O₁₂ composite ceramics were prepared by spark plasma sintering. Sintering behavior, microstructures and dielectric properties of the composite ceramics were investigated by XRD, SEM, EDS and dielectric spectrometer. Dense composite ceramics consisting of Ba_0.4Sr_0.6TiO₃ phase and CaCu₃Ti₄O₁₂ phase were prepared at 800 °C for 0 min. The dielectric loss of the composite ceramic decreased with increasing amount of Ba_0.4Sr_0.6TiO₃, and the high dielectric constant were retained. Moreover, the better temperature stability of dielectric constant was obtained. These improvements of dielectric characteristics have great scientific significance for potential application.     

Synthesis,structural analysis and dielectric properties of Ba8(Mg1−xZnx)Nb6O24 hexagonal perovskites

Ba₈(Mg_1−xZn_x)Nb₆O₂₄ (x=0, 0.2, 0.4, 0.6, 0.8 and 1) ceramics were prepared through the conventional solid-state route. The materials were calcined at 1250 °C and sintered at 1375–1425 °C. The structure of the system was analyzed using X-ray diffraction and vibrational spectroscopic studies. The microstructure of the sintered pellet was analyzed using scanning electron microscopy. The dielectric constant (ε_r), temperature coefficient of resonant frequency (τ_f) and the unloaded quality factor (Q_u) were measured in the microwave frequency region. The τ_f values of the compositions were reduced by varying the value of x from 0 to 1. The dielectric responses to frequency were also studied in the radio frequency region. The compositions have good microwave dielectric properties and hence are suitable for dielectric resonator applications.     

Microwave dielectric properties of BaO-2(1 − x)ZnO-xNd2O3-4TiO2 (x = 0-1.0) ceramics

Microwave dielectric properties of (1 − x)BaZn₂Ti₄O₁₁-xBaNd₂Ti₄O₁₂ (x = 0-1.0) ceramics were investigated by the solid-state reaction with the purpose of finding a microwave ceramics with high dielectric constant (?_r), high quality factor (Q × f) and low temperature coefficient of resonant frequency (τ_f). A two phase system BaZn₂Ti₄O₁₁-BaNd₂Ti₄O₁₂ was formed and SEM photographs show equiaxed BaZn₂Ti₄O₁₁ grains and columnar BaNd₂Ti₄O₁₂ grains. The microwave dielectric properties were strongly determined by the chemical composition. As increasing x from 0 to 1.0, the phase composition varied from pure BaZn₂Ti₄O₁₁, to the two phase system BaZn₂Ti₄O₁₁-BaNd₂Ti₄O₁₂ and then to pure BaNd₂Ti₄O₁₂. Therefore, the ?_r raised from 29.1 to 82.0 and the Q × f values decreased from 54,630 GHz to 8110 GHz, and the τ_f values increased from −29 ppm/°C to 94 ppm/°C. 0.8BaZn₂Ti₄O₁₁-0.2BaNd₂Ti₄O₁₂ ceramics sintered at 1250 °C for 2.5 h had ?_r = 39.1, Q × f = 37,850 GHz and τ_f = −9 ppm/ °C.     

Combustion synthesis of (Ti1−xNbx)2AlC solid solutions from elemental and Nb2O5/Al4C3-containing powder compacts

Preparation of the (Ti_1−xNb_x)₂AlC solid solution (formed from the M_n+1AX_n or MAX carbides, where n = 1, 2, or 3, M is an early transition metal, A is an A-group element, and X is C) with x = 0.2-0.8 was investigated by self-propagating high-temperature synthesis (SHS). Nearly single-phase (Ti,Nb)₂AlC was produced through direct combustion of constituent elements. Due to the decrease of reaction exothermicity, the combustion temperature and reaction front velocity decreased with increasing Nb content of (Ti_1−xNb_x)₂AlC formed from the elemental powder compacts. In addition, the samples composed of Ti, Al, Nb₂O₅, and Al₄C₃ were adopted for the in situ formation of Al₂O₃-added (Ti,Nb)₂AlC. The SHS process of the Nb₂O₅/Al₄C₃-containing sample involved aluminothermic reduction of Nb₂O₅, which not only enhanced the reaction exothermicity but also facilitated the evolution of (Ti,Nb)₂AlC. Based upon the XRD analysis, two intermediates, TiC and Nb₂Al, were detected in the (Ti,Nb)₂AlC/Al₂O₃ composite and their amounts were reduced by increasing the extent of thermite reduction involved in the SHS process. The laminated microstructure characteristic of the MAX carbide was observed for both monolithic and Al₂O₃-added (Ti,Nb)₂AlC solid solutions synthesized in this study.     

Low temperature sintering and microwave dielectric properties of Ce2(WO4)3 ceramics

Ce₂(WO₄)₃ ceramics have been synthesized by the conventional solid-state ceramic route. Ce₂(WO₄)₃ ceramics sintered at 1000 °C exhibited ?_r = 12.4, Qxf = 10,500 GHz (at 4.8 GHz) and τ_f = −39 ppm/°C. The effects of B₂O₃, ZnO–B₂O₃, BaO–B₂O₃–SiO₂, ZnO–B₂O₃–SiO₂ and PbO–B₂O₃–SiO₂ glasses on the sintering temperature and microwave dielectric properties of Ce₂(WO₄)₃ were investigated. The Ce₂(WO₄)₃ + 0.2 wt% ZBS sintered at 900 °C/4 h has ?_r = 13.7, Qxf = 20,200 GHz and τ_f = −25 ppm/°C.     

Sintering of glass-added BaZn1/3Nb2/3O3 ceramics

The complex perovskite oxide Ba(Zn_1/3Nb_2/3)O₃ (BZN) has been studied for its attractive dielectric properties which place this material interesting for applications as multilayer ceramics capacitors or hyperfrequency resonators. This material is sinterable at low temperature with combined glass phase–lithium salt additions, and exhibits, at 1 MHz very low dielectric losses combined with relatively high dielectric constant and a good stability of this later versus temperature. The 2 wt.% of ZnO–SiO₂–B₂O₃ glass phase and 1 wt.% of LiF-added BZN sample sintered at 900 °C exhibits a relative density higher than 95% and attractive dielectric properties: a dielectric constant ?_r of 39, low dielectrics losses (tan(δ) < 10⁻³) and a temperature coefficient of permittivity τ_? of 45 ppm/°C⁻¹. The 2 wt.% ZnO–SiO₂–B₂O₃ glass phase and 1 wt.% of B₂O₃-added BZN sintered at 930 °C exhibits also attractive dielectric properties (?_r = 38, tan(δ) < 10⁻³) and it is more interesting in terms of temperature coefficient of the permittivity (τ_? = −5 ppm/°C). Their good dielectric properties and their compatibility with Ag electrodes, make these ceramics suitable for L.T.C.C applications.     

Microwave dielectric properties of the (1 − x)Mg2TiO4-xCaTiO3-y wt.% ZnNb2O6 ceramics system

Composite ceramics based on (1 − x)Mg₂TiO₄-xCaTiO₃-y wt.% ZnNb₂O₆ (x = 0.12-0.16, y = 0-8) were prepared by a conventional mixed-oxide route. Zn²⁺ partially replaced Mg²⁺ in Mg₂TiO₄ and formed the spinel-structured (Mg_1−δZn_δ)₂TiO₄ phase. Nb²⁺, is known to be solid soluble in CaTiO₃, was found to change its shape from cubic to pliable. A bi-phase system (Mg_1−δZn_δ)₂TiO₄ and CaTiO₃ exhibited in all samples, where a small amount of second phase Mg_1−δZn_δTiO₃ was also detected. The microwave dielectric properties of specimens were strongly related to ZnNb₂O₆ and CaTiO₃ content. As y increased, ?_r and τ_f decreased, however, Q × f decreased to a minimum value and started to increase thereafter. It was also found that ?_r and τ_f increased and Q × f decreased with increasing x. The optimized microwave dielectric properties with ?_r = 18.37, Q × f = 31,027 GHz (at 6 GHz), and τ_f = 0.51 ppm/°C were achieved for (1 − x)Mg₂TiO₄-xCaTiO₃-y wt.% ZnNb₂O₆ (x = 0.12, y = 4) sintered at 1360 °C for 6 h.     

Phase diagram and properties of Pb(In1/2Nb1/2)O3-Pb(Mg1/3Nb2/3)O3-PbTiO3 polycrystalline ceramics

yPb(In_1/2Nb_1/2)O₃-(1 − x − y)Pb(Mg_1/3Nb_2/3)O₃-xPbTiO₃ (yPIN-(1 − x − y)PMN-xPT) polycrystalline ceramics with morphotropic phase boundary (MPB) compositions were synthesized using columbite precursor method. X-ray diffraction results indicated that the MPB of PIN-PMN-PT was located around PT = 0.33-0.36, confirmed by their respective dielectric, piezoelectric and electromechanical properties. The optimum properties were found for the MPB composition 0.36PIN-0.30PMN-0.34PT, with dielectric permittivity ?_r of 2970, piezoelectric coefficient d₃₃ of 450 pC/N, planar electromechanical coupling k_p of 49%, remanent polarization P_r of 31.6 μC/cm² and T_C of 245 °C. According to the results of dielectric and pyroelectric measurements, the Curie temperature T_C and rhombohedral to tetragonal phase transition temperature T_R-T were obtained, and the “flat” MPB for PIN-PMN-PT was achieved, indicating that the strongly curved MPB in PMN-PT system was improved by adding PIN component, offering the possibility to grow single crystals with high electromechanical properties and expanded temperature usage range (limited by T_R-T).     

Enhancement of the dielectric,piezoelectric, and ferroelectric properties in BiYbO3-modified (Ba0.85Ca0.15)(Ti0.9Zr0.1)O3 lead-free ceramics

Lead-free (1−x)(Ba_0.85Ca_0.15)(Ti_0.9Zr_0.1)O₃−xBiYbO₃ [(1−x)BCTZ−xBYO] piezoelectric ceramics in the range of BYO concentrations were prepared by the conventional oxide-mixed method, and the effect of BYO content on their microstructure, crystalline structure, density and electrical properties was investigated. A dense microstructure with large grain was obtained for the ceramics with the addition of BYO. The ceramics with x=0.1% exhibit an optimum electrical behavior of d₃₃~580 pC/N, r~10.9 Ω, k_p~56.4%, and tan δ~1.12% when sintered at a low temperature of ~1350 °C. When the measuring electric field is 40 kV/cm, the well-saturated and square-like P–E loops for the ceramics were observed with P_r~12.2 μC/cm² and E_c~1.83 kV/cm.