Effects of the Molecular Weight and the Side‐Chain Length on the Photovoltaic Performance of Dithienosilole/Thienopyrrolodione Copolymers

A series of low‐bandgap alternating copolymers of dithienosilole and thienopyrrolodione (PDTSTPDs) are prepared to investigate the effects of the polymer molecular weight and the alkyl chain length of the thienopyrrole‐4,6‐dione (TPD) unit on the photovoltaic performance. High‐molecular‐weight PDTSTPD leads to a higher hole mobility, lower device series resistance, a larger fill factor, and a higher photocurrent in PDTSTPD:[6,6]‐phenyl C₇₁ butyric acid methyl ester (PC₇₁BM) bulk‐heterojunction solar cells. Different side‐chain lengths show a significant impact on the interchain packing between polymers and affect the blend film morphology due to different solubilities. A high power conversion efficiency of 7.5% is achieved for a solar cell with a 1.0 cm² active area, along with a maximum external quantum efficiency (EQE) of 63% in the red region.     

The Effect of Poly(3‐hexylthiophene) Molecular Weight on Charge Transport and the Performance of Polymer:Fullerene Solar Cells

The time‐of‐flight method has been used to study the effect of P3HT molecular weight (M_n = 13–121 kDa) on charge mobility in pristine and PCBM blend films using highly regioregular P3HT. Hole mobility was observed to remain constant at 10^?4 cm²V^?1s^?1 as molecular weight was increased from 13–18 kDa, but then decreased by one order of magnitude as molecular weight was further increased from 34–121 kDa. The decrease in charge mobility observed in blend films is accompanied by a change in surface morphology, and leads to a decrease in the performance of photovoltaic devices made from these blend films.     

Enhanced Thermal Stability and Efficiency of Polymer Bulk‐Heterojunction Solar Cells by Low‐Temperature Drying of the Active Layer

This study addresses two key issues, stability and efficiency, of polymer solar cells based on blended poly(3‐hexylthiophene) (P3HT) and [6,6]‐phenyl‐C61‐butyric acid methyl ester (PCBM) by demonstrating a film‐forming process that involves low‐temperature drying (?5 °C) and subsequent annealing of the active layer. The low‐temperature process achieves 4.70% power conversion efficiency (PCE) and ～1250 h storage half‐life at 65 °C, which are significant improvements over the 3.39% PCE and ～143 h half‐life of the regular room‐temperature process. The improvements are attributed to the enhanced nucleation of P3HT crystallites as well as the minimized separation of the P3HT and PCBM phases at the low drying temperature, which upon post‐drying annealing results in a morphology consisting of small PCBM‐rich domains interspersed within a densely interconnected P3HT crystal network. This morphology provides ample bulk‐heterojunction area for charge generation while allowing for facile charge transport; moreover, the P3HT crystal network serves as an immobile frame at heating temperatures less than the melting point (T_m) of P3HT, thus preventing PCBM/P3HT phase separation and the corresponding device degradation.     

Polymer/Nanocrystal Hybrid Solar Cells: Influence of Molecular Precursor Design on Film Nanomorphology,Charge Generation and Device Performance

In this work, molecular tuning of metal xanthate precursors is shown to have a marked effect on the heterojunction morphology of hybrid poly(3‐hexylthiophene‐2,5‐diyl) (P3HT)/CdS blends and, as a result, the photochemical processes and overall performance of in situ fabricated hybrid solar cells. A series of cadmium xanthate complexes is synthesized for use as in situ precursors to cadmium sulfide nanoparticles in hybrid P3HT/CdS solar cells. The formation of CdS domains is studied by simultaneous GIWAXS (grazing incidence wide‐angle X‐ray scattering) and GISAXS (grazing incidence small‐angle X‐ray scattering), revealing knowledge about crystal growth and the formation of different morphologies observed using TEM (transmission electron microscopy). These measurements show that there is a strong relationship between precursor structure and heterojunction nanomorphology. A combination of TAS (transient absorption spectroscopy) and photovoltaic device performance measurements is used to show the intricate balance required between charge photogeneration and percolated domains in order to effectively extract charges to maximize device power conversion efficiencies. This study presents a strong case for xanthate complexes as a useful route to designing optimal heterojunction morphologies for use in the emerging field of hybrid organic/inorganic solar cells, due to the fact that the nanomorphology can be tuned via careful design of these precursor materials.     

Study on Polymer Films with Thermal Stability

New polymer film materials with good properties are reported.The difference between posivie and negative coronas is also given.The films have good transmittance,excellent thermal and long-term stability,low dielectric constant,and high glass transition temperature.     

Molecular Intercalation and Cohesion of Organic Bulk Heterojunction Photovoltaic Devices

The phase separated bulk heterojunction (BHJ) layer in BHJ polymer:fullerene organic photovoltaic devices (OPV) are mechanically weak with low values of cohesion. Improved cohesion is important for OPV device thermomechanical reliability. BHJ devices are investigated and how fullerene intercalation within the active layer affects cohesive properties in the BHJ is shown. The intercalation of fullerenes between the side chains of the polymers poly(3,3″′‐didocecyl quaterthiophene) (PQT‐12) and poly(2,5‐bis(3‐hexadecylthiophen‐2‐yl)thieno[3,2‐b]thiophene (pBTTT) is shown to enhance BHJ layer cohesion. Cohesion values range from ≈1 to 5 J m^?2, depending on the polymer:fullerene blend, processing conditions, and composition. Devices with non‐intercalated BHJ layers are found to have significantly reduced values of cohesion. The resulting device power conversion efficiencies (PCE) are also investigated and correlated with the device cohesion.     

Abrupt Morphology Change upon Thermal Annealing in Poly(3‐Hexylthiophene)/Soluble Fullerene Blend Films for Polymer Solar Cells

The in situ morphology change upon thermal annealing in bulk heterojunction blend films of regioregular poly(3‐hexylthiophene) (P3HT) and 1‐(3‐methoxycarbonyl)‐propyl‐1‐phenyl‐(6,6)C₆₁ (PCBM) is measured by a grazing incidence X‐ray diffraction (GIXD) method using a synchrotron radiation source. The results show that the film morphology—including the size and population of P3HT crystallites—abruptly changes at 140 °C between 5 and 30 min and is then stable up to 120 min. This trend is almost in good agreement with the performance change of polymer solar cells fabricated under the same conditions. The certain morphology change after 5 min annealing at 140 °C is assigned to the on‐going thermal transition of P3HT molecules in the presence of PCBM transition. Field‐emission scanning electron microscopy measurements show that the crack‐like surface of blend films becomes smaller after a very short annealing time, but does not change further with increasing annealing time. These findings indicate that the stability of P3HT:PCBM solar cells cannot be secured by short‐time annealing owing to the unsettled morphology, even though the resulting efficiency is high.     

Free Energy Control of Charge Photogeneration in Polythiophene/Fullerene Solar Cells: The Influence of Thermal Annealing on P3HT/PCBM Blends

The function of organic solar cells is based upon charge photogeneration at donor/acceptor heterojunctions. In this paper, the origin of the improvement in short circuit current of poly(3‐hexylthiophene)/6,6‐phenyl C₆₁‐butyric acid methyl ester (P3HT/PCBM) solar cells with thermal annealing is examined. Transient absorption spectroscopy is employed to demonstrate that thermal annealing results in an approximate two‐fold increase in the yield of dissociated charges. The enhanced charge generation is correlated with a decrease in P3HT's ionization potential upon thermal annealing. These observations are in excellent quantitative agreement with a model in which efficient dissociation of the bound radical pair into free charges is dependent upon the bound radical state being thermally hot when initially generated, enabling it to overcome its coulombic binding energy. These observations provide strong evidence that the lowest unoccupied molecular orbital (LUMO) level offset of annealed P3HT/PCBM blends may be only just sufficient to drive efficient charge generation in polythiophene‐based solar cells. This has important implications for current strategies to optimize organic photovoltaic device performance based upon the development of smaller optical bandgap polymers.     

High‐Performance Air‐Processed Polymer–Fullerene Bulk Heterojunction Solar Cells

High photovoltaic device performance is demonstrated in ambient‐air‐processed bulk heterojunction solar cells having an active blend layer of organic poly(3‐hexylthiophene) (P3HT): [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PCBM), with power conversion efficiencies as high as 4.1%, which is comparable to state‐of‐the‐art bulk heterojunction devices fabricated in air‐free environments. High‐resolution transmission electron microscopy is combined with detailed analysis of electronic carrier transport in order to quantitatively understand the effects of oxygen exposure and different thermal treatments on electronic conduction through the highly nanostructured active blend network. Improvement in photovoltaic device performance by suitable post‐fabrication thermal processing results from the reduced oxygen charge trap density in the active blend layer and is consistent with a corresponding slight increase in thickness of an ～4 nm aluminum oxide hole‐blocking layer present at the electron‐collecting contact interface.     

Precise Structural Development and its Correlation to Function in Conjugated Polymer: Fullerene Thin Films by Controlled Solvent Annealing

The impact of controlled solvent vapor exposure on the morphology, structural evolution, and function of solvent‐processed poly(3‐hexylthiophene):[6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (P3HT:PCBM) bilayers is presented. Grazing incident wide angle X‐ray scattering (GIWAXS) shows that the crystallization of P3HT increases with solvent exposure, while neutron reflectivity shows that P3HT simultaneously diffuses into PCBM, indicating that an initial bilayer structure evolves into a bulk heterojunction structure. Small angle neutron scattering (SANS) shows the agglomeration of PCBM and the formation of a PCBM pure phase when solvent annealing for 90 min. The structural evolution can be described as occurring in two stages: the first stage combines the enhanced crystallization of P3HT and diffusion of PCBM into P3HT, while the second stage entails the agglomeration of PCBM and formation of a PCBM pure phase. The phase separation of PCBM from P3HT is not driven by P3HT crystallinity, but is due to the concentration of PCBM exceeding the miscibility limit of PCBM in P3HT. Correlation of the morphology to photovoltaic activity shows that device performance significantly improves with solvent annealing for 90 min, indicating that both sufficient P3HT crystallization and formation of a PCBM pure phase are crucial in the optimization of the morphology of the active layer.     

Pore‐Filling of Spiro‐OMeTAD in Solid‐State Dye Sensitized Solar Cells: Quantification,Mechanism, and Consequences for Device Performance

In this paper, the pore filling of spiro‐OMeTAD (2,2′,7,7′‐tetrakis‐(N,N‐di‐p‐methoxyphenylamine)9,9′‐spirobifluorene) in mesoporous TiO₂ films is quantified for the first time using XPS depth profiling and UV–Vis absorption spectroscopy. It is shown that spiro‐OMeTAD can penetrate the entire depth of the film, and its concentration is constant throughout the film. We determine that in a 2.5‐µm‐thick film, the volume of the pores is 60–65% filled. The pores become less filled when thicker films are used. Such filling fraction is much higher than the solution concentration because the excess solution on top of the film can act as a reservoir during the spin coating process. Lastly, we demonstrate that by using a lower spin coating speed and higher spiro‐OMeTAD solution concentration, we can increase the filling fraction and consequently the efficiency of the device.     

Stability of Perovskite Thin Films under Working Condition: Bias-Dependent Degradation and Grain Boundary Effects

Witnessed by the rapid increase of power conversion efficiency to 25.5%, organic–inorganic hybrid perovskite solar cells (PSCs) are becoming promising candidates of next-generation photovoltaics. However, PSCs can be unstable under the influence of light and bias. Especially, grain boundaries (GBs) are vulnerable to attack by light and bias in perovskite films, leading to degradation of photovoltaic properties of PSCs. Herein, photocurrent atomic force microscopy and Kelvin probe force microscopy are employed to systematically investigate the bias-dependent charge transport behaviors and stability of (FAPbI₃)_0.85(MAPbBr₃)_0.15 perovskite under working condition. Bias-dependent morphology and photocurrent images show irreversible decomposition of the perovskite at a bias of 0.1 V or below, which is accelerated by light illumination, leading to formation of an interfacial layer that restricts carrier transport. Meanwhile, GBs appear to enhance carrier transport at larger bias, but serve as breakthrough sites for perovskite decomposition at smaller bias. Introducing excess methylammonium iodide promotes decomposition, while potassium iodide passivation greatly relieves the decomposition. These results support the ion migration mechanism of decomposition through interfaces and GBs. This work provides a deeper understanding of bias-induced degradation of PSCs as well as bias-dependent double-edged roles of GBs, and forms valuable guidance for appropriate operation of PSCs.     

Modification of PCBM Crystallization via Incorporation of C60 in Polymer/Fullerene Solar Cells

The morphological effects of the incorporation of C₆₀ into blended thin‐films of poly(3‐hexylthiophene) and [6,6]‐phenyl C₆₁ butyric acid methyl ester (PCBM) are investigated. The results show that addition of C₆₀ readily alters the growth‐rate and morphology of PCBM crystallites under different environmental conditions. The effect of C₆₀ on the growth of large PCBM crystallites is thoroughly characterized using optical microscopy, electron microscopy and UV‐visible absorption spectroscopy. Results show that C₆₀ incorporation modifies fullerene aggregation and crystallization and greatly reduces the average crystallite size at C₆₀ loadings of ≈50 wt% in the fullerene phase. Organic field‐effect transistors (OFETs) are prepared to evaluate the electron mobility of PCBM/C₆₀ films and organic solar cells (OSCs) are fabricated from mixed‐fullerene active layers to evaluate their performance. It is demonstrated that the use of fullerene mixtures in organic electronic applications is a viable approach to produce more stable devices and to control the growth of micrometer‐sized fullerene crystals.     

Template‐Directed Liquid ALD Growth of TiO2 Nanotube Arrays: Properties and Potential in Photovoltaic Devices

Dense and well‐aligned arrays of TiO₂ nanotubes extending from various substrates are successfully fabricated via a new liquid‐phase atomic layer deposition (LALD) in nanoporous anodic alumina (AAO) templates followed by alumina dissolution. The facile and versatile process circumvents the need for vacuum conditions critical in traditional gas‐phase ALD and yet confers ALD‐like deposition rates of 1.6–2.2 Å cycle^?1, rendering smooth conformal nanotube walls that surpass those achievable by sol–gel and Ti‐anodizing techniques. The nanotube dimensions can be tuned, with most robust structures being 150–400 nm tall, 60–70 nm in diameter with 5–20 nm thick walls. The viability of TiO₂ nanotube arrays deposited on indium tin oxide (ITO)–glass electrodes for application in model hybrid poly(3‐hexylthiophene) (P3HT):TiO₂ solar cells is studied. The results achieved provide platforms and research directions for further advancements.     

Improved Thermal Stability of Polymer Solar Cells by Incorporating Porphyrins

Thermal stability has been the important issue in organic solar cell, especially for the large scale fabrication and application in the future. In this work, a new strategy involving the introduction of porphyrin compound (BL) is proposed to prevent the [6,6]‐phenyl C61 butyric acid methyl ester (PC₆₁BM) aggregation. The supramolecular interactions between PC₆₁BM and BL are first demonstrated in PC₆₁BM:BL binary blend, and then the effect of BL on P3HT:PC₆₁BM blend is qualitatively and quantitatively studied by differential scanning calorimetry, UV–vis absorption spectroscopy, atomic force microscopy, optical microscopy, and fluorescence techniques. It is found that the BL addition not only stabilizes the morphology of P3HT:PC₆₁BM blend films, but also shows a good ability to maintain the electron mobility by depressing the PC₆₁BM crystallization. And the thermal stability of the devices based on P3HT:PC₆₁BM:BL ternary blend films is therefore greatly improved. For example, 8 wt% BL doping drops the power conversion efficiency by 10.5% relative to its peak value after 48 h of annealing at 130 °C, while 71.5% of decrease is obtained for the device without BL after only 3 h of annealing. This strategy is preliminarily proved to be universal and will show great potentials in future commercialization of polymer solar cells.     

Photocurrent Extraction Efficiency near Unity in a Thick Polymer Bulk Heterojunction

The detailed characterization of a dialkoxyphenylene‐difluorobenzothiadiazole based conjugated polymer poly[(2,5‐bis(2‐hexyldecyloxy)phenylene)‐alt‐(5,6‐difluoro‐4,7‐di(thiophen‐2‐yl)benzo[c][1,2,5]thiadiazole)] (PPDT2FBT) is reported. PPDT2FBT closely tracks theoretical photocurrent production while maintaining a high fill factor in remarkably thick films. In order to understand the properties that enable PPDT2FBT to function with thick active layers, the effect of film thickness on the material properties and device parameters was carefully studied and compared to three benchmark polymers. Optical modeling, grazing incidence wide angle X‐ray scattering, cross‐sectional transmission electron microscopy, transient photoconductivity, and extensive device work were carried out and have clarified the key structural features and properties that allow such thick active layers to function efficiently. The unique behavior of thick PPDT2FBT films arises from high vertical carrier mobility, an isotropic morphology with strong, vertical π–π stacking, and a suitable energy band structure. These physical characteristics allow efficient photocurrent extraction, internal quantum efficiencies near 100% and power conversion efficiencies over 9% from exceptionally thick active layers in both conventional and inverted architectures. The ability of PPDT2FBT to function efficiently in thick cells allows devices to fully attenuate incident sunlight while providing a pathway to defect‐free film processing over large areas, constituting a major advancement toward commercially viable organic solar cells.     

Recent advances in two-dimensional photovoltaic devices

Two-dimensional (2D) materials have attracted tremendous interest in view of the outstanding optoelectronic properties, showing new possibilities for future photovoltaic devices toward high performance, high specific power and flexibility. In recent years, substantial works have focused on 2D photovoltaic devices, and great progress has been achieved. Here, we present the review of recent advances in 2D photovoltaic devices, focusing on 2D-material-based Schottky junctions, homojunctions, 2D−2D heterojunctions, 2D−3D heterojunctions, and bulk photovoltaic effect devices. Furthermore, advanced strategies for improving the photovoltaic performances are demonstrated in detail. Finally, conclusions and outlooks are delivered, providing a guideline for the further development of 2D photovoltaic devices.     

The Effect of Ageing on Exciton Dynamics,Charge Separation,and Recombination in P3HT/PCBM Photovoltaic Blends

A study of how light‐induced degradation influences the fundamental photophysical processes in the active layer of poly(3‐hexylthiophene)/[6,6]‐phenyl C₆₁‐butyric acid methyl ester (P3HT/PCBM) solar cells is presented. Non‐encapsulated samples are systematically aged by exposure to AM 1.5 illumination in the presence of dry air for different periods of time. The extent of degradation is quantified by the relative loss in the absorption maximum of the P3HT, which is varied in the range 0% to 20%. For degraded samples an increasing loss in the number of excitons within the P3HT domains is observed with longer ageing periods. This loss occurs rapidly, within the first 15 ps after photoexcitation. A more pronounced decrease in the population of polarons than excitons is observed, which also occurs on a timescale of a few picoseconds. These observations, complemented by a quantitative analysis of the polaron and exciton population dynamics, unravel two primary loss mechanisms for the performances of aged P3HT/PCBM solar cells. One is an initial ultrafast decrease in the polaron generation, apparently not related to the exciton diffusion to the polymer/fullerene interface; the second, less significant, is a loss in the exciton population within the photoexcited P3HT domains. The steady‐state photoinduced absorption spectra of degraded samples exhibits the appearance of a signal ascribed to triplet excitons, which is absent for non‐degraded samples. This latter observation is interpreted considering the formation of degraded sites where intersystem crossing and triplet exciton formation is more effective. The photovoltaic characteristics of same blends are also studied and discussed by comparing the decrease in the overall power conversion efficiency of solar cells.