NbF5: A Novel α‐Phase Stabilizer for FA‐Based Perovskite Solar Cells with High Efficiency

The HC(NH₂)₂⁺(FA⁺) is a well‐known substitute to CH₃NH₃⁺(MA⁺) for its capability to extend light utilization for improved power conversion efficiency for perovskite solar cells; unfortunately, the dark cubic phase (α‐phase) can easily transition to the yellow orthorhombic phase (δ‐phase) at room temperature, an issue that prevents its commercial application. In this report, an inorganic material (NbF₅) is developed to stabilize the desired α‐phase perovskite material by incorporating NbF₅ additive into the perovskite films. It is found that the NbF₅ additive effectively suppresses the formation of the yellow δ‐phase in the perovskite synthesis and aging process, thus enhancing the humidity and light‐soaking stability of the perovskite film. As a result, the perovskite solar cells with the NbF₅ additive exhibit improved air stability by tenfold, retaining nearly 80% of their initial efficiency after aging in air for 50 d. In addition, under full‐sun AM 1.5 G illumination of a xenon lamp without any UV‐reduction, the perovskite solar cells with the NbF₅ additive also show fivefold improved illumination stability than the control devices without NbF₅.     

HPbI3: A New Precursor Compound for Highly Efficient Solution‐Processed Perovskite Solar Cells

Recently, there have been extensive research efforts on developing high performance organolead halide based perovskite solar cells. While most studies focused on optimizing the deposition processes of the perovskite films, the selection of the precursors has been rather limited to the lead halide/methylammonium (or formamidium) halide combination. In this work, we developed a new precursor, HPbI₃, to replace lead halide. The new precursor enables formation of highly uniform formamidium lead iodide (FAPbI₃) films through a one‐step spin‐coating process. Furthermore, the FAPbI₃ perovskite films exhibit a highly crystalline phase with strong (110) preferred orientation and excellent thermal stability. The planar heterojunction solar cells based on these perovskite films exhibit an average efficiency of 15.4% and champion efficiency of 17.5% under AM 1.5 G illumination. By comparing the morphology and formation process of the perovskite films fabricated from the formamidium iodide (FAI)/HPbI₃, FAI/PbI₂, and FAI/PbI₂ with HI additive precursor combinations, it is shown that the superior property of the HPbI₃ based perovskite films may originate from 1) a slow crystallization process involving exchange of H⁺ and FA⁺ ions in the PbI₆ octahedral framework and 2) elimination of water in the precursor solution state.     

Introduction of Hydrophobic Ammonium Salts with Halogen Functional Groups for High‐Efficiency and Stable 2D/3D Perovskite Solar Cells

2D perovskites have attracted extensive attention due to their excellent stability compared with 3D perovskites. However, the intrinsic hydrophilicity of introduced alkylammonium salts effects the humidity stability of 2D/3D perovskites. Devices based on longer chain alkylammonium salts show improvement in hydrophobicity but lower efficiency due to the poorer charge transport among various layers. To solve this issue, two hydrophobic short‐chain alkylammonium salts with halogen functional groups (2‐chloroethylamine, CEA⁺ and 2‐bromoethylamine, BEA⁺) are introduced into (Cs_0.1FA_0.9)Pb(I_0.9Br_0.1)₃ 3D perovskites to form 2D/3D perovskite structure, which achieve high‐quality perovskite films with better crystallization and morphology. The optimal 2D/3D perovskite solar cells (PSCs) with 5% CEA⁺ display a power conversion efficiency (PCE) as high as 20.08% under 1 sun irradiation. Because of the notable hydrophobicity of alkylammonium cations with halogen functional groups and the formed 2D/3D perovskite structure, the optimal PSCs exhibit superior moisture resistance and retain 92% initial PCE after aging at 50 ± 5% relative humidity for 2400 h. This work opens up a new direction for the design of new‐type 2D/3D PSCs with improved performance by employing proper alkylammonium salts with different functional groups.     

δ‐CsPbI3 Intermediate Phase Growth Assisted Sequential Deposition Boosts Stable and High‐Efficiency Triple Cation Perovskite Solar Cells

Cs/FA/MA triple cation perovskite films have been well developed in the antisolvent dripping method, attributable to its outstanding photovoltaic and stability performances. However, a facile and effective strategy is still lacking for fabricating high‐quality large‐grain triple cation perovskite films via sequential deposition method a, which is one of the key technologies for high efficiency perovskite solar cells. To address this issue, a δ‐CsPbI₃ intermediate phase growth (CsPbI₃‐IPG) assisted sequential deposition method is demonstrated for the first time. The approach not only achieves incorporation of controllable cesium into (FAPbI₃)_1–x(MAPbBr₃)_x perovskite, but also enlarges the perovskite grains, manipulates the crystallization, modulates the bandgap, and improves the stability of final perovskite films. The photovoltaic performances of the devices based on these Cs/FA/MA perovskite films with various amounts of the δ‐CsPbI₃ intermediate phase are investigated systematically. Benefiting from moderate cesium incorporation and intermediate phase‐assisted grain growth, the optimized Cs/FA/MA perovskite solar cells exhibit a significantly improved power conversion efficiency and operational stability of unencapsulated devices. This facile strategy provides new insights into the compositional engineering of triple or quadruple cation perovskite materials with enlarged grains and superior stability via a sequential deposition method.     

In Situ Growth of 2D Perovskite Capping Layer for Stable and Efficient Perovskite Solar Cells

2D halide perovskites have recently been recognized as a promising avenue in perovskite solar cells (PSCs) in terms of encouraging stability and defect passivation effect. However, the efficiency (less than 15%) of ultrastable 2D Ruddlesden–Popper PSCs still lag far behind their traditional 3D perovskite counterparts. Here, a rationally designed 2D‐3D perovskite stacking‐layered architecture by in situ growing 2D PEA₂PbI₄ capping layers on top of 3D perovskite film, which drastically improves the stability of PSCs without compromising their high performance, is reported. Such a 2D perovskite capping layer induces larger Fermi‐level splitting in the 2D‐3D perovskite film under light illumination, resulting in an enhanced open‐circuit voltage (V_oc) and thus a higher efficiency of 18.51% in the 2D‐3D PSCs. Time‐resolved photoluminescence decay measurements indicate the facilitated hole extraction in the 2D‐3D stacking‐layered perovskite films, which is ascribed to the optimized energy band alignment and reduced nonradiative recombination at the subgap states. Benefiting from the high moisture resistivity as well as suppressed ion migration of the 2D perovskite, the 2D‐3D PSCs show significantly improved long‐term stability, retaining nearly 90% of the initial power conversion efficiency after 1000 h exposure in the ambient conditions with a high relative humidity level of 60 ± 10%.     

Water‐Soluble Triazolium Ionic‐Liquid‐Induced Surface Self‐Assembly to Enhance the Stability and Efficiency of Perovskite Solar Cells

Despite being a promising candidate for next‐generation photovoltaics, perovskite solar cells (PSCs) exhibit limited stability that hinders their practical application. In order to improve the humidity stability of PSCs, herein, a series of ionic liquids (ILs) “1‐alkyl‐4‐amino‐1,2,4‐triazolium” (termed as RATZ; R represents alkyl chain, and ATZ represents 4‐amino‐1,2,4‐triazolium) as cations are designed and used as additives in methylammonium lead iodide (MAPbI₃) perovskite precursor solution, obtaining triazolium ILs‐modified PSCs for the first time (termed as MA/RATZ PSCs). As opposed to from traditional methods that seek to improve the stability of PSCs by functionalizing perovskite film with hydrophobic molecules, humidity‐stable perovskite films are prepared by exploiting the self‐assembled monolayer (SAM) formation of water‐soluble triazolium ILs on a hydrophilic perovskite surface. The mechanism is validated by experimental and theoretical calculation. This strategy means that the MA/RATZ devices exhibit good humidity stability, maintaining around 80% initial efficiency for 3500 h under 40 ± 5% relative humidity. Meanwhile, the MA/RATZ PSCs exhibit enhanced thermal stability and photostability. Tuning the molecule structure of the ILs additives achieves a maximum power conversion efficiency (PCE) of 20.03%. This work demonstrates the potential of using triazolium ILs as additives and SAM and molecular design to achieve high performance PSCs.     

Unveiling the Nanoparticle‐Seeded Catalytic Nucleation Kinetics of Perovskite Solar Cells by Time‐Resolved GIXS

Recently, a new seeding growth approach for perovskite thin films is reported to significantly enhance the device performance of perovskite solar cells. This work unveils the intermediate structures and the corresponding growth kinetics during conversion to perovskite crystal thin films assisted by seeding PbS nanocrystals (NCs), using time‐resolved grazing‐incidence X‐ray scattering. Through analyses of time‐resolved crystal formation kinetics obtained from synchrotron X‐rays with a fast subsecond probing time resolution, an important “catalytic” role of the seed‐like PbS NCs is clearly elucidated. The perovskite precursor‐capped PbS NCs are found to not only accelerate the nucleation of a highly oriented intermediate phase, but also catalyze the conversion of the intermediate phase into perovskite crystals with a reduced activation energy E_a = 47 (±5) kJ mol^?1, compared to 145 (±38) kJ mol^?1 for the pristine perovskite thin film. The reduced E_a is attributed to a designated crystal lattice alignment of the perovskite nanocrystals with perovskite cubic crystals; the pivotal heterointerface alignment of the perovskite crystals coordinated by the Pb NCs leads to an improved film surface morphology with less pinholes and enhanced crystal texture and thermal stability. These together contribute to the significantly improved photovoltaic performance of the corresponding devices.     

Octadecylamine‐Functionalized Single‐Walled Carbon Nanotubes for Facilitating the Formation of a Monolithic Perovskite Layer and Stable Solar Cells

Organic–inorganic lead halide perovskites have shown great future for application in solar cells owing to their exceptional optical and electronic properties. To achieve high‐performance perovskite solar cells, a perovskite light absorbing layer with large grains is desirable in order to minimize grain boundaries and recombination during the operation of the device. Herein, a simple yet efficient approach is developed to synthesize perovskite films consisting of monolithic‐like grains with micrometer size through in situ deposition of octadecylamine functionalized single‐walled carbon nanotubes (ODA‐SWCNTs) onto the surface of the perovskite layer. The ODA‐SWCNTs form a capping layer that controls the evaporation rate of organic solvents in the perovskite film during the postthermal treatment. This favorable morphology in turn dramatically enhances the short‐circuit current density of the perovskite solar cells and almost completely eliminates the hysteresis. A maximum power conversion efficiency of 16.1% is achieved with an ODA‐SWCNT incorporated planar solar cell using (FA_0.83MA_0.17)_0.95Cs_0.05Pb(I_0.83Br_0.17)₃ as light absorber. Furthermore, the perovskite solar cells with ODA‐SWCNT demonstrate extraordinary stability with performance retention of 80% after 45 d stability testing under high humidity (60–90%) environment. This work opens up a new avenue for morphology manipulation of perovskite films and enhances the device stability using carbon material.     

Sulfate‐Assisted Interfacial Engineering for High Yield and Efficiency of Triple Cation Perovskite Solar Cells with Alkali‐Doped TiO2 Electron‐Transporting Layers

Facile electron injection and extraction are two key attributes desired in electron transporting layers to enhance the efficiency of planar perovskite solar cells. Herein it is demonstrated that the incorporation of alkali metal dopants in mesoporous TiO₂ can effectively modulate electronic conductivity and improve the charge extraction process by counterbalancing oxygen vacancies acting as nonradiative recombination centers. Moreover, sulfate bridges (SO₄^2?) grafted on the surface of K‐doped mesoporous titania provide a seamless integration of absorber and electron‐transporting layers that accelerate overall transport kinetics. Potassium doping markedly influences the nucleation of the perovskite layer to produce highly dense films with facetted crystallites. Solar cells made from K:TiO₂ electrodes exhibit power conversion efficiencies up to 21.1% with small hysteresis despite all solution coating processes conducted under ambient air conditions (controlled humidity: 25–35%). The higher device efficiencies are attributed to intrinsically tuned electronic conductivity and chemical modification of grain boundaries enabling uniform coverage of perovskite films with large grain size.     

In Situ Observation of Crystallization Dynamics and Grain Orientation in Sequential Deposition of Metal Halide Perovskites

Metal halide perovskites have revolutionized the development of highly efficient, solution‐processable solar cells. Further advancements rely on improving perovskite film qualities through a better understanding of the underlying growth mechanism. Here, a systematic in situ grazing‐incidence X‐ray diffraction investigation is performed, facilitated by other techniques, on the sequential deposition of formamidinium lead iodide (FAPbI₃)‐based perovskite films. The active chemical reaction, composition distribution, phase transition, and crystal grain orientation are all visualized following the entire perovskite formation process. Furthermore, the influences of additive ions on the crystallization speed, grain orientation, and morphology of FAPbI₃‐based films, along with their photovoltaic performances, are fully evaluated and optimized, which leads to highly reproducible and efficient perovskite solar cells. The findings provide key insights into the perovskite growth mechanism and suggest the fabrication of high‐quality perovskite films for widespread optoelectronic applications.     

Solution‐Processed Laminated Perovskite Layers for High‐Performance Solar Cells

Laminated multilayers of perovskite films with different optical and electronic characteristics will easily realize high‐performance optoelectronic devices because it is widely demonstrated that differential distribution of film properties in the vertical direction of devices plays particularly important roles in device performance. However, the existing laminated perovskite films are hardly prepared by a solution process because there is no solvent with sufficient selectivity of solubility for different perovskite materials. Here, it is demonstrated that aniline (AN) has a largely different solubility toward the perovskite MAPbI₃ and the MAPbI₃ blend with an additive of hydrochloride diethylammonium chloride. By using AN as the solvent in the perovskite precursor solution, two laminated perovskite layers with different crystal size and optical and electrical characteristics are achieved. Inverted perovskite solar cells with the laminated films as active layers achieve an averaged power conversion efficiency of 20.65% originating from the high V_OC 1.112 V and fill factor of 80.8%. The devices maintain 98% efficiency after 400 h under 65% RH. This work provides a very simple and feasible method for production of laminated perovskite films to achieve high‐performance perovskite solar cells.     

FAPbI3‐Based Perovskite Solar Cells Employing Hexyl‐Based Ionic Liquid with an Efficiency Over 20% and Excellent Long‐Term Stability

Formamidinium lead triiodide (FAPbI₃)‐based perovskite materials are of interest for photovoltaics in view of their close‐to‐ideal bandgap, allowing absorption of photons over a broad solar spectrum. However, FAPbI₃‐based materials suffer from a notorious phase transition from the photoactive black phase (α‐FAPbI₃) to nonperovskite yellow phase (δ‐FAPbI₃) under ambient conditions. This transition dramatically reduces light absorbtion, thus, degrading the photovoltaic performance and stability of ensuring solar cells. In this study, 1‐hexyl‐3‐methylimidazolium iodide (HMII) ionic liquid (IL) is employed as an additive for the first time in FAPbI₃ perovskite to overcome the above‐mentioned issues. HMII incorporation facilitates the grain coarsening of FAPbI₃ crystal owing to its high‐polarity and high‐boiling point, which yields liquid domains between neighboring grains to reduce the activation energy of the grain‐boundary migration. As a result, the FAPbI₃ active layer exhibits micron‐sized grains with substantially suppressed parasitic traps with an Urbach energy reduced by 2 meV. Hence, the resulting perovskite solar cell achieves an efficiency of 20.6% with notable increase in open circuit voltage (V_OC) of 80 mV compared with HMII‐free cells (17.1%). More importantly, the HMII‐doped FAPbI₃‐based cells show a striking enhancement in shelf‐stability under high humidity and thermal stress, retaining >80% of their initial efficiencies at 60 ± 10% relative humidity and ≈95% at 65 °C.     

Viscosity effect of ionic liquid-assisted controlled growth of CH3NH3PbI3 nanoparticle-based planar perovskite solar cells

A precise control of the morphology and crystallization of perovskite thin-films is well-correlated to higher perovskite solar cells performances. Ionic liquids (ILs) can retard perovskite crystallization to aid the formation of films with uniform morphology to realize highly efficient perovskite solar cells. Herein, we attempt to control the nanostructural growth of CH₃NH₃PbI₃ thin films by adding ILs to the perovskite spin-coating solution and investigate the effect of IL viscosity on the resulting CH₃NH₃PbI₃ nanoparticle (NP) thin films. NPs with desirable morphology were obtained using ILs with a low viscosity that completely dissolved in the CH₃NH₃PbI₃ solution. In particular, the IL tetrabutylammonium chloride yielded NPs with a diameter of 500 nm and controllable morphology, crystallinity, and absorption behavior, which led to improved photovoltaic performance compared with that of solar cells containing NPs produced using other ILs. Our findings revealed a pathway to obtain uniformly distributed CH₃NH₃PbI₃ NP thin films for use in perovskite solar cells. The developed method is well suited for large-scale production of perovskite thin films on flexible substrates.     

Reduced Defects of MAPbI3 Thin Films Treated by FAI for High‐Performance Planar Perovskite Solar Cells

Organolead trihalide perovskite films with a large grain size and excellent surface morphology are favored to good‐performance solar cells. However, interstitial and antisite defects related trap‐states are originated unavoidably on the surfaces of the perovskite films prepared by the solution deposition procedures. The development of post‐growth treatment of defective films is an attractive method to reduce the defects to form good‐quality perovskite layers. Herein, a post‐treatment tactic is developed to optimize the perovskite crystallization by treating the surface of the one‐step deposited CH₃NH₃PbI₃ (MAPbI₃) using formamidinium iodide (FAI). Charge carrier kinetics investigated via time‐resolved photoluminescent, open‐circuit photovoltage decay, and time‐resolved charge extraction indicate that FAI post‐treatment will boost the perovskite crystalline quality, and further result in the reduction of the defects or trap‐states in the perovskite films. The photovoltaic devices by FAI treatment show much improved performance in comparison to the controlled solar cell. As a result, a champion solar cell with the best power conversion efficiency of 20.25% is obtained due to a noticeable improvement in fill factor. This finding exhibits a simple procedure to passivate the perovskite layer via regulating the crystallization and decreasing defect density.     

Morphological Control for High Performance,Solution‐Processed Planar Heterojunction Perovskite Solar Cells

Organometal trihalide perovskite based solar cells have exhibited the highest efficiencies to‐date when incorporated into mesostructured composites. However, thin solid films of a perovskite absorber should be capable of operating at the highest efficiency in a simple planar heterojunction configuration. Here, it is shown that film morphology is a critical issue in planar heterojunction CH₃NH₃PbI_3‐xCl_x solar cells. The morphology is carefully controlled by varying processing conditions, and it is demonstrated that the highest photocurrents are attainable only with the highest perovskite surface coverages. With optimized solution based film formation, power conversion efficiencies of up to 11.4% are achieved, the first report of efficiencies above 10% in fully thin‐film solution processed perovskite solar cells with no mesoporous layer.     

Impact of the Solvation State of Lead Iodide on Its Two‐Step Conversion to MAPbI3: An In Situ Investigation

Producing high efficiency solar cells without high‐temperature processing or use of additives still remains a challenge with the two‐step process. Here, the solution processing of MAPbI₃ from PbI₂ films in N,N‐dimethylformamide (DMF) is investigated. In‐situ grazing incidence wide‐angle X‐ray scattering (GIWAXS) measurements reveal a sol–gel process involving three PbI₂‐DMF solvate complexes—disordered (P₀) and ordered (P₁, P₂)—prior to PbI₂ formation. When the appropriate solvated state of PbI₂ is exposed to MAI (methylammonium Iodide), it can lead to rapid and complete room temperature conversion into MAPbI₃ with higher quality films and improved solar cell performance. Complementary in‐situ optical reflectance, absorbance, and quartz crystal microbalance with dissipation (QCM‐D) measurements show that dry PbI₂ can take up only one third of the MAI taken up by the solvated‐crystalline P₂ phase of PbI₂, requiring additional annealing and yet still underperforming. The perovskite solar cells fabricated from the ordered P₂ precursor show higher power conversion efficiency (PCE) and reproducibility than devices fabricated from other cases. The average PCE of the solar cells is greatly improved from 13.2(±0.53)% (from annealed PbI₂) to 15.7(±0.35)% (from P₂) reaching up to 16.2%. This work demonstrates the importance of controlling the solvation of PbI₂ as an effective strategy for the growth of high‐quality perovskite films and their application in high efficiency and reproducible solar cells.     

Triamine‐Based Aromatic Cation as a Novel Stabilizer for Efficient Perovskite Solar Cells

Operational stability of perovskite solar cells has been a challenge from the beginning of perovskite research. In general, humidity and heat are the most well‐known degradation sources for perovskites, requiring ideal design of perovskite chemistry to withstand them. Although triple‐cation perovskite (Cs_0.05(FA_0.85MA_0.15)_0.95Pb(I_0.85Br_0.15)₃) has been already introduced as the stable perovskite material, the high reactivity of methylammonium and formamidinium in the cation sites demands further modification. Herein, 1,2,4‐triazole is suggested as an effective cation solute to improve the performance and stability of perovskite solar cells. 1,2,4‐Triazole is an aromatic cation with low dipole moment that is stable under humidity and heat. It also possesses three nitrogen atoms, forming additional hydrogen bonds in the lattice, stabilizing the material. In this study, the solar cell utilizing 1,2,4‐triazole alloying achieves a power conversion efficiency of 20.9% with superior stability under extreme condition (85 °C/85% of relative humidity (RH), encapsulated) for 700 h. The 1,2,4‐triazole‐alloyed perovskite exhibits reduced trap density and film roughness and enhanced carrier lifetime with electrical conductivity, suggesting an ideal perovskite structure for efficient and stable optoelectronic applications.     

Interface Engineering by Thiazolium Iodide Passivation Towards Reduced Thermal Diffusion and Performance Improvement in Perovskite Solar Cells

Interface engineering has become one of the most facile and effective approaches to improve solar cells performance and its long‐term stability and to retard unwanted side reactions. Three passivating agents are developed which can functionalize the surface and induce hydrophobicity, by employing substituted thiazolium iodide (TMI) for perovskite solar cells fabrication. The role of TMI interfacial layers in microstructure and electro‐optical properties is assessed for structural as well as transient absorption measurements. TMI treatment resulted in V_OC and fill factor enhancement by reducing possible recombination paths at the perovskite/hole selective interface and by reducing the shallow as well as deep traps. These in turn allow to achieve higher performance as compared to the pristine surface. Additionally, the TMI passivated perovskite layer considerably reduces CH₃NH₃⁺ thermal diffusion and degradation induced by humidity. The un‐encapsulated perovskite solar cells employing TMI exhibit a remarkable stability under moisture levels (≈50% RH), retaining ≈95% of the initial photon current efficiency after 800 h of fabrication, paving the way towards a potential scalable endeavor.     

Conjugated Small Molecule for Efficient Hole Transport in High‐Performance p‐i‐n Type Perovskite Solar Cells

The π‐conjugated organic small molecule 4,4′‐cyclohexylidenebis[N,N‐bis(4‐methylphenyl) benzenamine] (TAPC) has been explored as an efficient hole transport material to replace poly(3,4‐ethylenedio‐xythiophene):poly(styrenesulfonate) (PEDOT:PSS) in the preparation of p‐i‐n type CH₃NH₃PbI₃ perovskite solar cells. Smooth, uniform, and hydrophobic TAPC hole transport layers can be facilely deposited through solution casting without the need for any dopants. The power conversion efficiency of perovskite solar cells shows very weak TAPC layer thickness dependence across the range from 5 to 90 nm. Thermal annealing enables improved hole conductivity and efficient charge transport through an increase in TAPC crystallinity. The perovskite photoactive layer cast onto thermally annealed TAPC displays large grains and low residual PbI₂, leading to a high charge recombination resistance. After optimization, a stabilized power conversion efficiency of 18.80% is achieved with marginal hysteresis, much higher than the value of 12.90% achieved using PEDOT:PSS. The TAPC‐based devices also demonstrate superior stability compared with the PEDOT:PSS‐based devices when stored in ambient circumstances, with a relatively high humidity ranging from 50 to 85%.     

Low‐Dimensional Lead‐Free Inorganic Perovskites for Resistive Switching with Ultralow Bias

3D organic–inorganic and all‐inorganic lead halide perovskites have been intensively pursued for resistive switching memories in recent years. Unfortunately, instability and lead toxicity are two foremost challenges for their large‐scale commercial applications. Dimensional reduction and composition engineering are effective means to overcome these challenges. Herein, low‐dimensional inorganic lead‐free Cs₃Bi₂I₉ and CsBi₃I₁₀ perovskite‐like films are exploited for resistive switching memory applications. Both devices demonstrate stable switching with ultrahigh on/off ratios (≈10⁶), ultralow operation voltages (as low as 0.12 V), and self‐compliance characteristics. 0D Cs₃Bi₂I₉‐based device shows better retention time and larger reset voltage than the 2D CsBi₃I₁₀‐based device. Multilevel resistive switching behavior is also observed by modulating the current compliance, contributing to the device tunability. The resistive switching mechanism is hinged on the formation and rupture of conductive filaments of halide vacancies in the perovskite films, which is correlated with the formation of AgI_x layers at the electrode/perovskite interface. This study enriches the library of switching materials with all‐inorganic lead‐free halide perovskites and offers new insights on tuning the operation of solution‐processed memory devices.