Studies on isomeric effects of 2- and 4-Mercapto pyridine as dopants in polymer electrolyte in dye-sensitized solar cells

In this present work, isomers like 2- and 4-Mercapto pyridine were used as dopants (additives) in Poly (ethylene oxide) based polymer electrolyte and their effects in dye-sensitized solar cells (DSC) have been investigated. Due to the coordinating and plasticizing effects of Mercapto pyridine, enhanced ionic conductivity and reduced crystallinity of PEO polymer electrolyte accompanied by a better penetration of the same into the dye coated nanocrystalline TiO₂ in order to have better performances were achieved. The 2-Mercapto pyridine doped PEO (E) shows comparatively better performance than 4-Mercapto pyridine doped one (F), is due to the fact that the π-electron donicity of 2-Mercapto pyridine is greater. These results suggests that the electron donating capacity of 2-Mercapto pyridine and 4-Mercapto pyridine would influence the interaction of nanocrystalline TiO₂ electrode and I⁻/I₃⁻ redox couple leading to radical changes in the cell performance.     

Application of poly(acrylic acid-g-gelatin)/polypyrrole gel electrolyte in flexible quasi-solid-state dye-sensitized solar cell

A novel gel polymer electrolyte based on poly(acrylic acid-g-gelatin)/polypyrrole with conductivity of 14.1 mS cm⁻¹ was prepared. Based on the gel electrolyte, a flexible quasi-solid-state dye-sensitized solar cell was fabricated by using a low-temperature filming technique. Owing to high conductivity and the catalytic function of polypyrrole for I⁻/I₃⁻ redox reaction for the gel electrolyte, the flexible quasi-solid-state dye-sensitized solar cell showed a light-to-electric energy conversion efficiency of 1.28%, under a simulated solar light irradiation with intensity of 100 mW cm⁻² (AM 1.5).     

Influence of solvent on the poly (acrylic acid)-oligo-(ethylene glycol) polymer gel electrolyte and the performance of quasi-solid-state dye-sensitized solar cells

The influence of solvents on the property of poly (acrylic acid)-oligo-(ethylene glycol) polymer gel electrolyte and photovoltaic performance of quasi-solid-state dye-sensitized solar cells (DSSCs) were investigated. Solvents or mixed solvents with large donor number enhance the liquid electrolyte absorbency, which further influences the ionic conductivity of polymer gel electrolyte. A polymer gel electrolyte with ionic conductivity of 4.45 mS cm⁻¹ was obtained by using poly (acrylic acid)-oligo-(ethylene glycol) as polymer matrix, and absorbing 30 vol.% N-methyl pyrrolidone and 70 vol.% γ-butyrolactone with 0.5 M NaI and 0.05 M I₂. By using this polymer gel electrolyte coupling with 0.4 M pyridine additive, a quasi-solid-state dye-sensitized solar cell with conversion efficiency of 4.74% was obtained under irradiation of 100 mW cm⁻² (AM 1.5).     

Influence of ionic additives NaI/I2 on the properties of polymer gel electrolyte and performance of quasi-solid-state dye-sensitized solar cells

The ionic additives NaI/I₂ in polymer gel electrolyte not only provide cations, but also affect the liquid electrolyte absorbency of the poly(acrylic acid)-poly(ethylene glycol) hybrid, which results in the change of ionic conductivity of polymer gel electrolyte and the photovoltaic performance of quasi-solid-state dye-sensitized solar cell. With the optimized components of liquid electrolyte containing 0.5 M NaI, 0.05 M I₂, 0.4 M pyridine, 70 vol.% γ-butyrolactone and 30 vol.% N-methylpyrrolidone, a 4.74% power conversion efficiency of quasi-solid-state dye-sensitized solar cell was obtained under 100 mW cm⁻² (AM 1.5) irradiation.     

The preparation of poly(glycidyl acrylate)-polypyrrole gel-electrolyte and its application in dye-sensitized solar cells

A microporous hybrid of poly(glycidyl acrylate)-polypyrrole (PGA-PPy) was synthesized by a two-step solution polymerization. Using this hybrid as polymer host, a gel-electrolyte with high conductivity of 12.83 mS cm⁻¹ was prepared. The researches by scanning electron microscopy (SEM), Fourier transform infrared spectra (FTIR), and cyclic voltammetry (CV) show that the microporous structure and functional groups for PGA allows the higher absorbency and good ionic salt tolerance for the electrolyte, the introduction of PPy causes a lower charge-transfer resistance and higher electrocatalytic activity for the I₃⁻/I⁻ redox reaction for the electrolyte. Based on the electrolyte, a dye-sensitized solar cell with a light-to-electrical energy conversion efficiency of 5.03% is achieved, under illumination with a simulated solar light of 100 mW cm⁻² (AM 1.5).     

The use of 2,6-bis (N-pyrazolyl) pyridine as an efficient dopant in conjugation with poly(ethylene oxide) for nanocrystalline dye-sensitized solar cells

Poly(ethylene oxide) (PEO)/2,6-bis (N-pyrazolyl) pyridine (BNPP) polymer electrolyte based photoelectrochemical cells have been fabricated with [cis-dithiocyanato-N, N-bis (2,2′ bipyridyl-4, 4′ dicarboxylic acid)ruthenium(II)] dihydrate (N3 dye) dye complex as the sensitizer and nanoporous TiO₂ film as photo anode. The introduction of 2,6-bis (N-pyrazolyl) pyridine into the poly (ethylene oxide) matrix reduces the crystallinity of the polymer and enhances the mobility of I⁻/I₃⁻ redox couple resulting in an improved performance with a higher conversion efficiency of 8.8% in terms of light energy to electric energy when compared to that of the corresponding dye-sensitized nanocrystalline TiO₂ solar cell.     

Application of a polymer heterojunction in dye-sensitized solar cells

Using a blend heterojunction consisting of a C₆₀ derivative, [6,6]-phenyl-C₆₁-butyric acid methyl ester (PCBM), and poly(3-hexylthiophene) (P3HT) as a charge carrier transfer medium to replace the I₃⁻/I⁻ redox electrolyte, a novel TiO₂/dye/PCBM/P3HT dye-sensitized solar cell was fabricated and characterized. It was found that the P3HT/PCBM heterojunction widened the incident light harvest range from ultraviolet to visible light, and improved the photoelectrical response of the dye-sensitized solar cell. We investigated the influence of the PCBM/P3HT ratio and barrier layer on the photoelectric performance of the solar cell and proposed optimized preparation conditions. The optimized solar cell with a barrier layer and PCBM/P3HT ratio of 1:2 had a short circuit current density of 5.52 mA cm⁻², an open circuit voltage of 0.87 V, a fill factor of 0.640 and a light-to-electric energy conversion efficiency of 3.09% under a simulated solar light irradiation of 100 mW cm⁻².     

Influence of various cations on redox behavior of I and I3 and comparison between KI complex with 18-crown-6 and 1,2-dimethyl-3-propylimidazolium iodide in dye-sensitized solar cells

In this paper, we studied the influence of different cations on redox behavior of I⁻ and I₃⁻ by cyclic voltammetry and electrochemical impedance spectroscopy. It was demonstrated that increasing cation size tends to give rise to higher reductive activity of I⁻ and lower diffusion coefficient of I₃⁻ in these cations, alkylimidazolium, [Na ⊂ 15-C-5]⁺ and [K ⊂ 18-C-6]⁺. Moreover, we measured the performance of dye-sensitized solar cells (DSCs) with electrolyte containing [K ⊂ 18-C-6]I or 1,2-dimethyl-3-propylimidazolium iodide (DMPII). It was found that dye-sensitized solar cells (DSCs) with [K ⊂ 18-C-6]I give a little higher short-circuit photocurrent density and a little lower fill factor than DSCs with DMPII.     

Influence of molecular weight of PEG on the property of polymer gel electrolyte and performance of quasi-solid-state dye-sensitized solar cells

A new kind of polymer gel electrolyte based on poly(acrylic acid)-poly(ethylene glycol) (PAA-PEG) hybrid was synthesized. The factor of molecular weight of PEG in the hybrid plays an important role in determining the liquid electrolyte absorbency of the hybrid and ionic conductivity of the polymer gel electrolyte, sequentially affects the photovoltaic performance of quasi-solid-state dye-sensitized solar cells. Using the hybrid with PEG molecular weight of 20,000, a polymer gel electrolyte with liquid electrolyte absorbency of 6.9 g g⁻¹ and ionic conductivity of 5.35 mS cm⁻¹ was obtained. Based on the polymer gel electrolyte, a quasi-solid-state dye-sensitized solar cell with conversion efficiency of 5.25% was achieved under irradiation of AM 1.5, 100 mW cm⁻².     

Influence of 2,6 (N-pyrazolyl)isonicotinic acid on the photovoltaic properties of a dye-sensitized solar cell fabricated using poly(vinylidene fluoride) blended with poly(ethylene oxide) polymer electrolyte

A novel method of introducing a synthesized organic nitrogenous compound 2,6 (N-pyrazolyl)isonicotinic acid (BNIN) and its effect on the conduction behavior of poly(vinylidene fluoride) (PVdF)–poly(ethylene oxide) (PEO) polymer-blend electrolyte with potassium iodide (KI) and iodine (I₂) and the corresponding performance of the dye-sensitized solar cells (DSSCs) were studied. A systematic investigation of the blends using FTIR provides evidence of interaction of BNIN with the polymer. Differential scanning calorimetry (DSC) study proves the miscibility of these polymers. Due to the coordinating and plasticizing effects of BNIN, the ionic conductivity of polymer blend electrolytes is enhanced. The efficiency of DSSC using BNIN doped polymer blend electrolyte was 7.3% under an illumination of 60 mW cm⁻² were observed for the best performance of a solar cell in this work.     

Dye-sensitised photoelectrochemical solar cells with polyacrylonitrile based solid polymer electrolytes

Novel all solid state dye-sensitised photolectrochemical solar cells of the type, FTO-TiO₂-dye-PAN, EC, PC, Pr₄N⁺I⁻, I₂-Pt-FTO, have been fabricated and characterised using current-voltage characteristics and action spectra. Liquid electrolyte generally used for such solar cells has successfully replaced by a quasi solid electrolyte comprised of polyacrylonitrile (PAN) with ethylene carbonate (EC) and propylene carbonate (PC) as plasticisers and Pr₄N⁺I⁻/I₂ redox couple with tetrapropylammoniumiodide as the complexing salt. For the polymer electrolyte, the optimum conductivity of 2.95×10⁻³ S cm⁻¹ was obtained for the electrolyte composition, PAN:EC:PC=15:35:50 (wt.%). The short circuit current density (J_SC) and the open circuit voltage (V_OC) obtained for an incident light intensity of 600 W m⁻² were 3.73 mA cm⁻² and 0.69 V, respectively. This corresponds to an overall quantum efficiency of 2.99%. From the action spectrum, the maximum incident photon conversion efficiency (IPCE) of 33% was obtained for incident light of wavelength 480 nm.     

Influences of poly(ether urethane) introduction on poly(ethylene oxide) based polymer electrolyte for solvent-free dye-sensitized solar cells

A poly(ether urethane) (PEUR)/poly(ethylene oxide) (PEO)/SiO₂ based nanocomposite polymer is prepared and employed in the construction of high efficiency all-solid-state dye-sensitized nanocrystalline solar cells. The introduction of low-molecular weight PEUR prepolymer into PEO electrolyte has greatly enhance the electrolyte performance by both improving the interfacial contact properties of electrode/electrolyte and decreasing the PEO crystallization, which were confirmed by XRD and SEM characteristics. The effects of polymer composition, nano SiO₂ content on the ionic conductivity and I₃⁻ ions diffusion of polymer-blend electrolyte are investigated. The optimized composition yields an energy conversion efficiency of 3.71% under irradiation by white light (100 mW cm⁻²).     

Gel polymer electrolyte based on poly(acrylonitrile-co-styrene) and a novel organic iodide salt for quasi-solid state dye-sensitized solar cell

A gel polymer electrolyte based on poly(acrylonitrile-co-styrene) as polymer matrix and N-methyl pyridine iodide salt as I⁻ source was prepared. Controlling the concentration of polymer matrix of poly(acrylonitrile-co-styrene) at 17.5 wt.%, mixing the binary organic solvents mixture ethylene carbonate and propylene carbonate with 6:4 (w/w), and the concentration of N-methyl pyridine iodide and iodine with 0.5 and 0.05 M, respectively, the gel polymer electrolyte attains the maximum ionic conductivity (at 30 °C) of 4.63 mS cm⁻¹. Based on the gel polymer electrolyte, a quasi-solid state dye-sensitized solar cell was fabricated and its overall energy conversion efficiency of light-to-electricity of 3.10% was achieved under irradiation of 100 mW cm⁻².     

The role of gel electrolyte composition in the kinetics and performance of dye-sensitized solar cells

Gel-type polymer electrolytes based on the copolymer poly(ethylene oxide-co-epichlorohydrin) and the plasticizer γ-butyrolactone (GBL) were optimized and applied in dye-sensitized solar cells. The plasticizer added to the electrolyte allowed the dissolution of a higher concentration of salt, reaching conductivity values close to 1 mS cm⁻¹ for the sample prepared with 30 wt% of LiI. Raman spectroscopy confirmed polyiodide formation in the electrolyte when the salt concentration exceeds 7.5 wt%, introducing a significant contribution of electronic conductivity in the electrolyte. The devices were characterized under AM 1.5 conditions and the I-V curves were fitted using a two diode equation. Increasing the concentration of LiI-I₂ accelerates dye cation regeneration as measured by transient absorption spectroscopy; however, it also contributes to an increase in the dark current of the cell by one order of magnitude. The best performance was achieved for the solar cell prepared with the electrolyte containing 20 wt% of LiI, with efficiencies of 3.26% and 3.49% at 100 and 10 mW cm⁻² of irradiation, respectively.     

In situ quaterizable oligo-organophosphazene electrolyte with modified nanocomposite SiO2 for all-solid-state dye-sensitized solar cell

Two latent chemical cross-linked precursors: (1) oligo-organophosphazene with propionitrile and iodo-(ethylene oxide-co-propylene oxide) and (2) oligo-organosiloxane grafting oligo-ethylene oxide and propylene oxide dimethylamine are synthesized to form all-solid-state polymer electrolyte for dye-sensitized solar cells employing in situ quaterization reaction. This novel electrolyte shows about 6.79 × 10⁻⁷ cm² s⁻¹ of the apparent diffusion coefficient of triiodide. The disintegrating temperature of 181 °C demonstrates good thermal stability of the solid-state electrolyte. Proper amount of 7 nm SiO₂ modified with 3-triethoxysilylpropyl oligo(oxyethylene-co-oxypropylene) monomethyl urethane is added to the electrolyte and the photocurrent conversion efficiency reaches 2.66% compared with that of 1.81% with no additive.     

Low-cost dyes based on methylthiophene for high-performance dye-sensitized solar cells

Three donor–acceptor, π-conjugated (D–π–A) dyes containing methylthiophene or vinylene methylthiophene as π-conjugated spacer were utilised in dye-sensitized nanocrystalline TiO₂ solar cells. The relationship between the structure of the dyes and their photophysical, electrochemical and photovoltaic properties was investigated systematically. The vinyl unit, introduced as the π-conjugated spacer, leads to unfavorable back-electron transfer and decrease of the open-circuit voltage. A dye-sensitized solar cell based on 2-cyano-3-(5-(4-(diphenylamino)phenyl)-4-methylthiophenyl-2-yl) acrylic acid displayed the most efficient solar-to-electricity conversion efficiency of the dyes with a maximum η value of 8.27% (V_oc = 0.72 V, J_sc = 15.76 mA cm⁻², FF = 0.73) under simulated AM 1.5 G solar irradiation (100 mW cm⁻²).     

Novel chemically cross-linked solid state electrolyte for dye-sensitized solar cells

Poly(vinylpyridine-co-ethylene glycol methyl ether methacrylate) (P(VP-co-MEOMA)) and α,ω-diiodo poly(ethylene oxide-co-propylene oxide) (I[(EO)_0.8-co-(PO)_0.2]_yI) were synthesized and used as chemically cross-linked precursors of the electrolyte for dye-sensitized solar cells. Meanwhile, α-iodo poly(ethylene oxide-co-propylene oxide) methyl ether (CH₃O[(EO)_0.8-co-(PO)_0.2]_xI) was synthesized and added into the electrolyte as an internal plasticizer. Novel polymer electrolyte resulting from chemically cross-linked precursors was obtained by the quaterisation at 90 °C for 30 min. The characteristics for this kind of electrolyte were investigated by means of ionic conductivity, thermogravimetric and photocurrent-voltage. The ambient ionic conductivity was significantly enhanced to 2.3 × 10⁻⁴ S cm⁻¹ after introducing plasticizer, modified-ionic liquid. The weight loss of the solid state electrolyte at 200 °C was 1.8%, and its decomposition temperature was 287 °C. Solid state dye-sensitized solar cell based on chemically cross-linked electrolyte presented an overall conversion efficiency of 2.35% under AM1.5 irradiation (100 mW cm⁻²). The as-fabricated device maintained 88% of its initial performance at room temperature even without sealing for 30 days, showing a good stability.     

Membrane-based electrolyte sheets for facile fabrication of flexible dye-sensitized solar cells

New electrolyte sheets based on porous polyethylene membranes for flexible dye-sensitized solar cells have been developed. Ionic liquid electrolytes are accommodated in commercial polyethylene membranes to form the electrolyte sheets. The morphology of membranes and iodine concentrations in ionic liquid are varied. The electrochemical measurement results show that the morphology, pore structure, and iodine concentration affect mass transport in electrolyte sheet, as well as charge transfer between platinum electrode and electrolyte sheet greatly. Based on these electrolyte sheets, lamination method instead of conventional vacuum injection of electrolyte is used to fabricate flexible dye-sensitized solar cells. Optimal device with an open-circuit voltage (V_oc) of 0.63 V, a fill factor of 0.58, and a short-circuit current density (J_sc) of 6.17 mA cm⁻² at an incident light intensity of 100 mW cm⁻² is obtained, which yields a light-to-electricity conversion efficiency of 2.25%.     

A polyblend electrolyte (PVP/PEG+KI+I2) for dye-sensitized nanocrystalline TiO2 solar cells

A novel polyblend electrolyte consisting of KI and I₂ dissolved in a blending polymer of polyvinyl pyrrolidone (PVP) and polyethylene glycol (PEG) was prepared. The formation of ⁻I₃ in the polymer electrolyte was confirmed by X-ray photoelectron spectroscopy (XPS) characterization. Due to the coordinating and plasticizing effect by PVP, the ionic conductivity of the polyblend electrolyte is enhanced. The highest ionic conductivity of 1.85 mS cm⁻¹ for the polyblend electrolyte was achieved by optimizing the compositions as 40 wt.% PVP + 60 wt.% PEG + 0.05 mmol g⁻¹ I₂ + 0.10 mmol g⁻¹ KI. Based on the polyblend electrolyte, a DSSC with fill factor of 0.59, short-circuit density of 9.77 mA cm⁻², open-circuit voltage of 698 mV and light-to-electricity conversion efficiency of 4.01% was obtained under AM 1.5 irradiation (100 mW cm⁻²).     

Conversion enhancement of flexible dye-sensitized solar cells based on TiO2 nanotube arrays with TiO2 nanoparticles by electrophoretic deposition

We prepared highly ordered titanium dioxide nanotube arrays (TNAs) by anodizing Ti foils in F⁻ containing electrolyte. The thickness and dye loading amount of TNAs were 26 μm and 1.06 × 10⁻⁷ mol cm⁻², respectively. TiO₂ nanoparticles (TNPs) were electrophoretically deposited on the inner wall of nanotube to produce coated nanotube arrays (TNAP). The dye loading was increased to 1.56 × 10⁻⁷ mol cm⁻², and the electron transport rate improved. TNAs and TNAP were sensitized with ruthenium dye N3 to yield dye-sensitized TiO₂ nanotube solar cells. The power conversion efficiency of TNA-based dye-sensitized solar cells (DSSCs) was 4.28%, whereas the efficiency of TNAP-based DSSCs increased to 6.28% when illuminated from the counter electrode. The increase of power conversion efficiency of TNAP-based DSSCs is ascribed to the increased surface area of TNAs and the faster electron transport rate.