微米铜粉/纳米TiO_2复合粒子的低温制备及光吸收性能

利用仿生合成的方法在温和条件下制备了微米铜粉/纳米TiO2复合粒子.选择有机胺对Cu粉进行表面处理,XPS分析表明有机胺通过N原子与表面Cu2+络合形成功能层,在Cu粉表面引入NH2和OH等功能基团,对比实验证实功能基团能够诱导无机氧化物的仿生沉积.XRD结果表明铜粉表面包覆的纳米TiO2呈现锐钛矿晶型,漫反射光谱(DRS)分析表明,Cu粉经过有机胺处理后在716.5nm处出现了由Cu2+离子与N配位产生的弱吸收.复合粒子的光吸收性能介于TiO2和Cu粉之间,Cu负载后样品的光吸收阀值从397.5nm红移至448.9nm,红移的原因可归于Cu负载后TiO2导带下出现新能级,光生电子经过这些中间能级发生跃迁,所需激发能量降低至可见光范围.448.9nm处吸收边的存在表明复合粒子具备可见光催化活性.     

Ag掺杂APS改性的TiO2颗粒的制备及其光催化降解作用

为提高Ag/TiO2纳米颗粒的光催化降解作用,采用聚合凝胶工艺路线,以钛酸四丁酯为前驱体,硝酸银为银源,通过向反应体系引入鳌合剂醋酸、表面改性剂γ-氨丙基三乙氧基硅烷(APS)以及还原剂甲醛等添加剂,制备出TiO2粉体及Ag/TiO2纳米复合粉体。利用FT-IR、XRD、TG-DTA、TEM和UV-Vis-NIR等手段对样品进行表征。结果表明,经γ-氨丙基三乙氧基硅烷改性的TiO2颗粒掺Ag后分散性得到改善,粒径约1 nm的Ag颗粒较均匀地分布在10～15 nm TiO2颗粒上;可见光的利用和锐钛矿热稳定性都得到提高;Ag/TiO2纳米颗粒在光照下对甲基橙具有良好的光催化降解效果。     

不同气氛下TiO2纳米晶的光催化性能研究

以甲基橙的光催化降解为探针反应,从表观降解率和TOC去除率两个指标评价了纳米TiO2样品在不同焙烧温度和反应气氛下的光催化活性.结果表明,400℃焙烧的锐钛矿型TiO2纳米粒子的晶粒尺寸为11.69nm,在光催化降解甲基橙的实验中表现出最佳的光催化活性.光催化反应进行20min后对甲基橙的表现降解率达98.99%,反应进行30min后对甲基橙水溶液TOC的去除率为79.36%,TOC的去除效果滞后于色度的去除.不通空气时,样品对甲基橙的降解率最差,降解速率明显滞后于通空气和O2的情况,且通O2的降解效果更好.     

PPy/TiO2纳米复合材料的制备及光催化活性

采用原位聚合的方法合成了聚吡咯/二氧化钛(PPy/TiO2)纳米复合材料,研究了吡咯(Py)与TiO2的比例、氧化剂的种类、掺杂酸的浓度等因素对PPy/TiO2纳米复合材料在太阳光下光催化降解甲基橙的影响,采用透射电镜、紫外-可见漫反射吸收光谱等方法对样品进行了表征.结果表明,PPy/TiO2纳米复合粒子在太阳光下的光催化活性明显高于TiO2纳米粒子,当Py与TiO2的比例为1:100,三氯化铁为氧化剂,1.0mol·L-1盐酸溶液为掺杂剂时PPy/TiO2纳米复合粒子在太阳光下的光催化活性最高;TiO2纳米微粒以及PPy/TiO2纳米复合微粒的粒径均为10～20nm,复合微粒的粒径没有明显的增大,但是减轻了纳米粒子之间的团聚;聚吡咯使TiO2纳米粒子的禁带宽度由3.12eV降低到2.84eV,TiO2纳米粒子的吸收波长拓展到可见光区,有利于TiO2纳米粒子在太阳光下光催化活性的提高.     

Cu/TiO2 纳米线的制备及其光催化性能

以P25粉体为原料,采用水热法合成了TiO2 纳米线,通过NaBH4还原CuCl2溶液,在TiO2纳米线的表面负载了Cu纳米颗粒.利用透射电镜(TEM)、X射线光电子能谱(XPS)和紫外-可见光谱(UV-Vis)对产物进行了表征.结果表明,Cu纳米粒子均匀分散在纳米线表面,并且该Cu/TiO2纳米线在可见光区域表现出较强的吸收性能.光催化降解酸性红3R染料溶液测试表明,在TiO2纳米线表面负载Cu纳米颗粒对提高其催化性能具有积极作用.     

高活性TiO2纳米晶的酸催化Sol-Gel法制备与表征

采用酸催化的溶胶-凝胶法制备出了纳米TiO2光催化剂，以甲基橙的光催化降解为探针反应，评价了其光催化活性．运用XRD、TEM、FT—IR以及PL光谱技术对纳米TiO2的微晶尺寸、晶体结构、表面组成和性能进行表征．结果表明，400℃焙烧的TiO2纳米粒子的颗粒形貌为近球形，晶粒尺寸为11．69 nm，样品分散性良好的锐钛矿型结构．在光催化降解甲基橙的实验中，400℃焙烧的TiO2纳米粒子表现出最高的光催化活性，这与表征结果一致．此外，550℃和650℃焙烧的具有锐钛矿型和金红石型混晶结构的TiO2纳米粒子，无混晶协同促进效应．     

Ag/TiO_2复合纳米催化剂的制备和表征及其光催化性能研究

以TiCl4,AgNO3为原料,采用水热法制备了Ag/TiO2复合纳米催化剂。采用X-射线衍射仪、透射电镜等对其进行结构表征,得到金红石型均匀掺杂的Ag/TiO2复合纳米颗粒。为了评估Ag/TiO2光催化材料的催化活性,在中性条件下以Ag/TiO2作为光催化剂,进行了在自然光下催化降解甲基橙的实验,实验结果表明:Ag/TiO2复合纳米催化剂对甲基橙的光催化降解具有较好的催化作用。     

AgX-TiO2纳米复合催化剂在可见光下的催化性能

以纳米带钛酸为二氧化钛的来源,通过离子交换-煅烧的方法制得了系列AgX(X=Cl,Br,I)/TiO2复合纳米材料。紫外可见吸收光谱表明,AgX/TiO2纳米复合材料在可见光400~470 nm范围内都有很好的吸收。以甲基橙(MO)的可见光降解为探针反应,结果表明:AgBr/TiO2与其他催化剂相比具有较高的光催化活性,在6 min内MO的降解率达到了80%。催化活性高的主要原因是AgBr与TiO2有更好的能带匹配,在光照下电子更易于转移到TiO2的导带上,减少了电子-空穴的复合。     

Ag/TiO2纳米管复合材料的合成及其光催化性能研究

采用水热法制备了TiO2纳米管,并采用光化学沉积法制得含Ag量不同的Ag/TiO2-NTs纳米管复合材料;利用XRD、TEM、XPS、UV-Vis及FL等分析手段对Ag/TiO2-NTs复合材料进行表征,并研究了Ag/TiO2-NTs对甲基橙(MO)的紫外光催化降解性能。结果表明,Ag纳米粒子均匀分散在纳米管表面,Ag/TiO2-NTs复合材料在可见光区域表现出较强的吸收性能;Ag含量为4%的Ag/TiO2-NTs复合材料光催化降解率最高,紫外光照射3h后,初始浓度为10mg/L的甲基橙溶液降解率达到99%,比未掺Ag的TiO2纳米管降解率提高了16.6%。     

Ag+/Ag-TiO2纳米空心球制备及其可见光催化性能

在TiO2/聚苯乙烯复合材料表面沉积硫化银,空气中煅烧制备了Ag+/Ag修饰的二氧化钛纳米空心球(Ag+/Ag-TiO2纳米空心球,即Ag+/Ag-HTS)。结果表明,所制备的Ag+/Ag-HTS具有可见光催化降解甲基橙的活性,随着甲基橙的初始浓度降低其催化降解效率提高。肖特基势垒的形成有助于更多的空穴转移到材料的表面,增强其光催化效率;表面的Ag+有助于电子的清除,防止光激电子与光激空穴复合。随着硫化银沉积数量的提高,Ag+/Ag-HTS的可见光催化活性提高,其光催化降解甲基橙的反应具有假一级反应的动力学特征。使用25%Ag+/Ag-HTS光催化剂,在可见光下照射2 h甲基橙降解率高达70.6%。     

Insertion of triangulated surfaces into a meccano tetrahedral discretization by means of mesh refinement and optimization procedures

In this paper, we present a new method for inserting several triangulated surfaces into an existing tetrahedral mesh generated by the meccano method. The result is a conformal mesh where each inserted surface is approximated by a set of faces of the final tetrahedral mesh. First, the tetrahedral mesh is refined around the inserted surfaces to capture their geometric features. Second, each immersed surface is approximated by a set of faces from the tetrahedral mesh. Third, following a novel approach, the nodes of the approximated surfaces are mapped to the corresponding immersed surface. Fourth, we untangle and smooth the mesh by optimizing a regularized shape distortion measure for tetrahedral elements in which we move all the nodes of the mesh, restricting the movement of the edge and surface nodes along the corresponding entity they belong to. The refining process allows approximating the immersed surface for any initial meccano tetrahedral mesh. Moreover, the proposed projection method avoids computational expensive geometric projections. Finally, the applied simultaneous untangling and smoothing process delivers a high‐quality mesh and ensures that the immersed surfaces are interpolated. Several examples are presented to assess the properties of the proposed method.     

Certification Institutions Expected to Update and Transfer Information on Present Standards

Standards are the basis for production enterprises to organize production, ex-factory inspection, trade (delivery) and technical exchanges, product certification, quality arbitration and supervision.……     

Flow calorimeter for enthalpy increment measurements on condensed gases

A flow calorimeter for enthalpy increment measurements on condensed gases is presented. A better knowledge of the properties of the liquefied natural gas is needed, and therefore a liquid loop has been designed for our flow calorimeter. The fluid loop in the calorimeter is designed in order to avoid the two-phase region, since two phases would give compositional disturbances in the measurements. The avoidance of the two-phase region is made possible by increasing the pressure of the test fluid after the measurement section, then heating the fluid at super-critical pressure past the critical point. Finally, the fluid is throttled to the low-pressure gas state at the inlet condition of the compressor that circulates the fluid. To perform the pressure increase, a new cryogenic pump has been designed. To evaluate the new equipment, measurements were taken on liquid ethane over the temperature range 146–256 K at pressure between 0.9 and 5.1 MPa.     

Refrigerators Enter a New Era of Health Preservation Frestech initiates the establishment of China's first standard for household sterilization refrigerators

On November 30, 2007, the China Association for Standardization (CAS) held a press conference at Beijing Diaoyutai State Guest House. Leaders from the China Household Electric Appliance Research Institute, the China Household Electric Appliance Association, and the China Consumers' Association attended and made speeches.……     

Optimum-Simulation von Ernteprozessen

Zusammenfassung Bei der Gestaltung von Ernteprozessen — beispielsweise des Prozesses Mähdrusch, Körnertransport und -abnahme — als transportverbundene Fließarbeitsverfahren mit mindestens zwei verschiedenen Arbeitsmitteln gibt es einen großen Optimierungsspielraum. Solche Prozesse sind mehrstufige Bedienungsprozesse mit gemischter Anordnung der Bedienungseinrichtungen. Außerdem besitzen sie stark ausgeprägte räumliche Aspekte. Es wird vor allem gezeigt, welche Merkmale solcher Prozesse in Simulationsmodellen abgebildet sein müssen, welche Zielgrößen in Abhängigkeit von welchen Einflußgrößen unter Berücksichtigung welcher Prozeßbedingungen ermittelt werden sollten und wie der Bewertungsprozeß zur Ermittlung der gewünschten Informationen gestaltet werden muß.     

A study of centrifugal cast high boron high speed steel

In the present study a high‐boron high speed steel (HSS) roll material was designed. Many expensive alloy elements have been substituted by cheap boron alloy, and high‐boron high speed steel roll has been manufactured by centrifugal casting method. The microstructures, mechanical properties and wear resistance of centrifugal casting high‐boron high speed steel roll have been investigated by optical microscopy (OM), scanning electron microscopy (SEM), and X‐ray diffraction (XRD) analysis, hardness test, impact test and wear test. The results indicated that the solidification microstructures of high‐boron high speed steel roll consisted of M₂(B,C), (W,Mo)₂(B,C), M₃(B,C), M₂₃(B,C)₆ type borocarbides and martensite, a small amount of retained austenite. Borocarbides were continuously distributed over the grain boundary. After quenching from 1050 °C, local broken network appeared in partial borocarbides, and fine secondary borocarbide precipitated from the matrix. After tempering from 525 °C, the amount of precipitated borocarbide increased significantly. After heat treatment, the hardness of high‐boron high speed steel roll excelled 60 HRC, and its impact toughness excelled 8.0 J/cm². The single groove steel rolling amount of high‐boron high speed steel rolls increases by 500% than that of bainite cast iron roll, when the rolls are used in K₁ mill housing of bar mill.     

Thixotropy of Systems with Shear Thinning and Plastic Flow Behavior

The definition of the thixotropy is a decrease in viscosity with time in shear and a subsequent recovery of viscosity after the shear deformation is removed.We ...     

Effect of Oxide Assisted Metal Nanoparticles on Microstructure and Morphology of Gallium oxide Nanowires

Several researches have been reported about the characteristic of β-Ga2O3 nanowires which was synthesized on nickel oxide particle. But indeed, recent researches about synthesis of β-Ga2O3 nanowires on oxide-assisted transition metal are limited to nickel or cobalt oxide catalyst. In this work, Gallium oxide (β-Ga2O3 ) nanowires were synthesized by a simple thermal evaporation method from gallium powder in the range of 700 - 1000℃ using the iron, nickel, copper, cobalt and zinc oxide as a catalyst, respectively. The β-Ga2O3 nanowires with single crystalline without defects were successfully synthesized at the reaction temperature of 850, 900 and 950℃ in all the catalysts. But optimum experimental condition in synthesis of nanowires varied with the kind of catalyst. As increasing synthesis temperature,the morphology of gallium oxide nanowires changed from nanowires to nanorods, and its diameter increased. From these results, we could be proposed that the growth mechanism of β-Ga2O3 nanowires was changed with synthesis temperature of nanowires. Microstructure and morphology of Synthesized nanowire was characterized by HR-TEM, FE-SEM, EDX and XRD.     

Brainstorming for ISO Strategy 2016-2020

正Responding to ISO’s appeal for survey for the to-be-developed ISO Strategy Plan for 2016-2020,SAC hosted a special workshop over the needs and comments of various fi elds on June 8 in Beijing.The workshop was attended by ISO President-elect and Ansteel General Manager Zhang Xiaogang,SAC Vice-Administrator Yu Xinli,and 30 experts from