Structure and Microwave Dielectric Characteristics of Ca1+xNd1−xAl1−xTixO4 Ceramics

CaNdAlO₄ microwave dielectric ceramics were modified by Ca/Ti co-substitution, and their dielectric characteristics were evaluated along with their structure and microstructures. Ca_{1+ x} Nd_{1− x} Al_{1− x} Ti _x O₄ ( x =0, 0.025, 0.05, 0.10, 0.15, 0.20) ceramics with the relative density of over 95% theoretical density were obtained by sintering at 1400°–1450°C in air for 3 h, where the K₂NiF₄-type solid solution single phase was determined from the compositions of x <0.20, while a small amount of CaTiO₃ secondary phase was detected for x =0.20. With Ca/Ti co-substitution in CaNdAlO₄ ceramics, the dielectric constant (ɛ_r) increased with increasing x , and the temperature coefficient of resonant frequency (τ_f) was adjusted from negative to positive, while the Q × f ₀ value increased significantly at first and reached an extreme value at x =0.025 and the maximum at x =0.15. The best combination of microwave dielectric characteristics were achieved at x =0.15 (ɛ_r=19.5, Q × f ₀=93 400 GHz, τ_f=−2 ppm/°C). The improvement of the Q × f ₀ value primarily originated from the reduced interlayer polarization with Ca/Ti co-substitution, while the decreased tolerance factor, the subsequent increased interlayer stress, and the appearance of CaTiO₃ secondary phase brought negative effects upon the Q × f ₀ value.     

High Q Microwave Dielectric Ceramics in (Ni1−x Znx)Nb2O6 System

(Ni_{1− x} Zn _x )Nb₂O₆, 0≤ x ≤1.0, ceramics with >97% density were prepared by a conventional solid-state reaction, followed by sintering at 1200°–1300°C (depending on the value of x ). The XRD patterns of the sintered samples (0≤ x ≤1.0) revealed single-phase formation with a columbite ( Pbcn ) structure. The unit cell volume slightly increased with increasing Zn content ( x ). All the compositions showed high electrical resistivity (ρ_dc=1.6±0.3 × 10¹¹Ω·cm). The microwave (4–5 GHz) dielectric properties of (Ni_{1− x} Zn _x )Nb₂O₆ ceramics exhibited a significant dependence on the Zn content and to some extent on the morphology of the grains. As x was increased from 0 to 1, the average grain size monotonically increased from 7.6 to 21.2 μm and the microwave dielectric constant (ɛ'_r) increased from 23.6 to 26.1, while the quality factors ( Q _u× f ) increased from 18 900 to 103 730 GHz and the temperature coefficient of resonant frequency (τ_f) increased from −62 to −73 ppm/°C. In the present work, we report the highest observed values of Q _u× f =103 730 GHz, and ɛ'_r=26.1 for the ZnNb₂O₆-sintered ceramics.     

High-Q Microwave Dielectrics in the (Mg1−xCox)2TiO4 Ceramics

The microwave dielectric properties and the microstructures of (Mg_{1− x} Co _x )₂TiO₄ ceramics prepared by the conventional solid-state route were investigated. Lattice parameters were also measured for specimens with different x . The formation of solid solution (Mg_{1− x} Co _x )₂TiO₄ ( x =0.02–0.1) was confirmed by the X-ray diffraction patterns, energy dispersive X-ray analysis, and the lattice parameters measured. By increasing x from 0 to 0.05, the Q × f of the specimen can be tremendously boosted from 150 000 GHz to a maximum of 286 000 GHz. A fine combination of microwave dielectric properties (ɛ_r∼15.7, Q × f ∼286 000 GHz at 10.4 GHz, τ_f∼−52.5 ppm/°C) was achieved for (Mg_0.95Co_0.05)₂TiO₄ ceramics sintered at 1390°C for 4 h. Ilmenite-structured (Mg_0.95Co_0.05)TiO₃ was detected as a second phase. The presence of the second phase would cause no significant variation in the dielectric properties of the specimen because it possesses compatible properties compared with that of the main phase. In addition, only a small deviation in the dielectric properties was monitored for specimens with x =0.04–0.05 at 1360°–1420°C. It not only provides a wide process window but also ensures an extremely reliable material proposed as a very promising dielectric for low-loss microwave and millimeter wave applications.     

Sintering Behavior, Phase Evolution, and Microwave Dielectric Properties of Bi(Sb1−xTax)O4 Ceramics

Sintering behavior, phase evolution, and microwave dielectric properties of Bi(Sb_{1− x} Ta _x )O₄ ceramics (0.05≤ x ≤0.60) were studied and their relationships were discussed in detail. Phase studies revealed that a pure monoclinic phase could be formed when x ≤0.20 and a pure orthorhombic phase could be obtained when x ≥0.50. As the x value increased from 0.05 to 0.60, the densified temperature of Bi(Sb_{1− x} Ta _x )O₄ ceramics decreased from 1050° to about 960°C whereas the density increased from 8.07 to 8.41 g/cm³. The microwave dielectric constant increased from 20.5 to 34 whereas the Q × f value decreased from 60 000 to 29 000 GHz. In the monoclinic phase region, the temperature coefficients of resonant frequency shifted linearly from −58 to −45 ppm/°C as the x value increased from 0.05 to 0.2 and then remained constant at about −12 ppm/°C when x ≥0.40. The Bi(Sb_{1− x} Ta _x )O₄ ceramics are promising for application of low-temperature cofired ceramics technology.     

Effect of V2O5 Doping on the Sintering and Dielectric Properties of M-Phase Li1+x−yNb1−x−3yTix+4yO3 Ceramics

The effect of the addition of V₂O₅ on the structure, sintering and dielectric properties of M -phase (Li_{1+ x − y} Nb_{1− x −3 y} Ti _x +4 _y )O₃ ceramics has been investigated. Homogeneous substitution of V⁵⁺ for Nb⁵⁺ was obtained in LiNb_{0.6(1− x )}V_{0.6 x} Ti_0.5O₃ for x ≤ 0.02. The addition of V₂O₅ led to a large reduction in the sintering temperature and samples with x = 0.02 could be fully densified at 900°C. The substitution of vanadia had a relatively minor adverse effect on the microwave dielectric properties of the M -phase system and the x = 0.02 ceramics had [alt epsilon]_r= 66, Q × f = 3800 at 5.6 GHz, and τ_f= 11 ppm/°C. Preliminary investigations suggest that silver metallization does not diffuse into the V₂O₅-doped M -phase ceramics at 900°C, making these materials potential candidates for low-temperature cofired ceramic (LTCC) applications.     

Structure and Microwave Dielectric Properties of Hexagonal Ba[Ti1−x(Ni1/2W1/2)x]O3 Ceramics

Microwave dielectric ceramics with the composition of Ba[Ti_{1− x} (Ni_1/2W_1/2) _x ]O₃ ( x =0.4–0.6) were prepared by a solid-state reaction method. The evolution of the crystalline phases was investigated by X-ray powder diffraction analysis. A cubic-to-hexagonal phase transition occurred between 1000° and 1300°C. The phase transition is irreversible; thus, the hexagonal phase remains stable at room temperature. The X-ray powder diffraction data for x =0.5 were refined using the Rietveld method. It was identified as a h -BaTiO₃-type hexagonal perovksite with the space group of P 6₃/ mmc . It also reveals that random occupancy of Ti⁴⁺ and W⁶⁺ ions occurs in the B-site substructures, whereas Ni²⁺ ions exclusively occupy the octahedral site in the corner-sharing octahedron. The dielectric properties of dense-sintered ceramics were characterized at microwave frequencies. With an increase in x from 0.4 to 0.6, the Q × f value increased from 26 700 to 42 000 GHz, whereas ɛ_r decreased from 29.8 to 20.0, and τ_f from +6.5 to −9.9 ppm/°C.     

Microwave Dielectric Properties of CaTiO3-CaAl1/2Nb1/2O3 Ceramics Doped with Li3NbO4

The microwave dielectric properties of CaTi_{1− x} (Al_1/2Nb_1/2) _x O₃ solid solutions (0.3 ≤ x ≤ 0.7) have been investigated. The sintered samples had perovskite structures similar to CaTiO₃. The substitution of Ti⁴⁺ by Al³⁺/Nb⁵⁺ improved the quality factor Q of the sintered specimens. A small addition of Li₃NbO₄ (about 1 wt%) was found to be very effective for lowering sintering temperature of ceramics from 1450–1500° to 1300°C. The composition with x = 0.5 sintered at 1300°C for 5 h revealed excellent dielectric properties, namely, a dielectric constant (ɛ_r) of 48, a Q × f value of 32 100 GHz, and a temperature coefficient of the resonant frequency (τ_f) of −2 ppm/K. Li₃NbO₄ as a sintering additive had no harmful influence on τ_f of ceramics.     

Structure–Property Relationships of BaTi1−2yGayNbyO3 (0≤y≤0.35) Ceramics

BaTi_{1−2 y} Ga _y Nb _y O₃ (BTGN) (0≤ y ≤0.35) powders were synthesized at 1300°C by the conventional solid-state method. Room temperature x-ray diffraction patterns for y ≤0.025 and 0.05≤ y ≤0.30 can be indexed as the tetragonal ( P 4 mm ) and cubic ( Pm     m ) polymorphs of BaTiO₃, respectively, whereas y =0.35 consists of a mixture of the cubic polymorph of BaTiO₃ and an 8H hexagonal-type perovskite ( P 6₃/ mcm ) isostructural with Ba₈Ti₃Nb₄O₂₄. Scanning electron microscopy shows the microstructures of BTGN ceramics ( y ≤0.30) sintered at 1500°C to consist of fine grains (1–3 μm) within a narrow grain size and shape distribution. Room temperature transmission electron microscopy for y ≤0.08 reveals core–shell structures and (111) twins in some grains; however, their relative volume decreases with y . Energy dispersive spectroscopy reveals the cores to be Ga and Nb deficient with respect to y . For y >0.08 there is no evidence of core–shell structures, however, some grains have a high density of dislocations, consistent with chemical inhomogeneity. BTGN ceramics exhibit a diverse range of dielectric behavior in the temperature range 120–450 K and can be subdivided into two groups. 0.025≤ y ≤0.15 display modest ferroelectric relaxor-type behavior, with high room temperature permittivity, ɛ₂₅', (>300 at 10 kHz), whereas 0.25≤ y ≤0.30 are temperature and frequency stable dielectrics with ɛ₂₅'<100 that resonate at microwave frequencies with modest quality factors, Q × f , ∼3720 GHz (at ∼5 GHz) for y =0.30.     

Effects of La on Dielectric and Piezoelectric Properties of Pb1−xLa2x/3(Nb0.95Ti0.0625)2 O6 Ceramics

Ceramics with the chemical compositions of Pb_{1− x} La_{2 x /3}(Nb_0.95Ti_0.0625)₂O₆ (0≤ x ≤0.060) (PLTN) were prepared by the conventional solid-state reaction method. X-ray diffraction analysis indicated that Ti and La doping not only decreased the rhombohedral–tetragonal phase transformation temperature, but also stabilized the orthorhombic phase of PLTN ceramics. All ceramics sintered at 1190°–1250°C had shown the pure orthorhombic ferroelectric phase. La doping suppresses grain growth and inhibits the formation of pores and cracks, resulting in an increase in relative density up to 97%. The amount of La doping to PLTN ceramics obviously affect ceramics' piezoelectric constant ( d ₃₃) and dielectric loss (tanδ). The sample with x =0.015 possesses high Curie temperature ( T _c=560°C), low dielectric loss (tanδ=0.0054), and excellent piezoelectric constant ( d ₃₃=92 pC/N), presenting a high potential to be used in high-temperature applications as piezoelectric transducers.     

Effects of Ca/Ti Cosubstitution upon Microwave Dielectric Characteristics of CaSmAlO4 Ceramics

(Ca_{1+ x} Sm_{1− x} )(Al_{1− x} Ti _x )O₄ (0≤ x ≤0.4) ceramics were synthesized by solid-state reaction method and their microstructures and microwave dielectric properties were investigated. X-ray diffraction analysis and energy-dispersive X-ray analysis indicated that the matrix phase was a solid solution with a composition represented by the chemical formula (Ca_{1+ x} Sm_{1− x} ) (Al_{1− x} Ti _x )O₄ and minor amount of (Ca,Sm)(Al,Ti)O₃ secondary phase was detected. Ca/Ti cosubstitution could significantly improve the microwave dielectric characteristics of CaSmAlO₄ ceramics, and the excellent microwave dielectric characteristics were obtained in the modified ceramics as ɛ_r=19–23, Q × f =49 100–118 700 GHz, and τ_f=−15–15 ppm/°C.     

Reduced Dielectric Loss of Modified ZnNb2O6 Ceramics by Substituting Nb5+ with Ta5+

The effects of substituting Nb⁵⁺ with Ta⁵⁺ on the microwave dielectric properties of the ZnNb₂O₆ ceramics were investigated in this study. The forming of Zn(Nb_{1− x} Ta _x )₂O₆ ( x =0–0.09) solid solution was confirmed by the measured lattice parameters and the EDX analysis. By increasing x , not only could the Q × f of the Zn(Nb_{1− x} Ta _x )₂O₆ ( x =0–0.09) solid solution be tremendously boosted from 83 600 GHz at x =0 to a maximum 152 000 GHz at x =0.05, the highest ɛ_r∼24.6 could also be achieved simultaneously. It was mainly due to the uniform grain morphology and the highest relative density of the specimen. A fine combination of microwave dielectric properties (ɛ_r∼24.6, Q × f ∼152 000 GHz at 8.83 GHz, τ_f∼–71.1 ppm/°C) was achieved for Zn(Nb_0.95Ta_0.05)₂O₆ solid solution sintered at 1175°C for 2 h.     

Densification, Structure, and Thermophysical Properties of Ytterbium–Gadolinium Zirconate Ceramics

(Yb _x Gd_{1− x} )₂Zr₂O₇ (0≤ x ≤1.0) ceramic powders synthesized with the chemical-coprecipitation and calcination method were pressureless-sintered at 1550–1700°C to develop new thermal barrier oxides with a lower thermal conductivity than yttria-stabilized zirconia ceramics. (Yb _x Gd_{1− x} )₂Zr₂O₇ ceramics exhibit a defective fluorite-type structure. The linear thermal expansion coefficients of (Yb _x Gd_{1− x} )₂Zr₂O₇ ceramics increase with increasing temperature from room temperature to 1400°C. The measured thermal conductivity of (Yb _x Gd_{1− x} )₂Zr₂O₇ ceramics first gradually decrease with increasing temperature and then slightly increase above 800°C because of the increased radiation contribution. YbGdZr₂O₇ ceramics have the lowest thermal conductivity among all the composition combinations studied.     

Effects of Calcium Substitution on the Structural and Microwave Dielectric Characteristics of [(Pb1−xCax)1/2La1/2](Mg1/2Nb1/2)O3 Ceramics

The effects of calcium substitution on the structural and microwave dielectric characteristics of [(Pb_{1− x} Ca _x )_1/2La_1/2](Mg_1/2Nb_1/2)O₃ ceramics (with x = 0.01–0.5) were investigated. All the materials were observed to have an ordered A(B_1/2^'B_1/2^")O₃-type perovskite structure; however, the space group of the structure changed from Fm 3 m to Pa 3 as the calcium content increased to x = 0.1, and then from Pa 3 to R 3¯ at the x = 0.5 composition. During the structural evolution, the lattice parameter of the perovskite cell decreased linearly, and the dielectric constant ( k ) also decreased, from k = 80 to k = 38. However, the product of the quality factor and the resonant frequency ( Q × f ) increased from 50 000 GHz to 90 000 GHz as the calcium content increased. Also, the temperature coefficient of resonant frequency (τ_ƒ) gradually changed from 120 ppm/°C to −40 ppm/°C as the calcium content increased. At the x = 0.3 composition, a combination of properties— k ∼ 50, Q × f ∼ 86 000 GHz, and τ_ƒ∼ 0 ppm/°C—can be obtained.     

Low-Loss Microwave Dielectric Ceramics Using (Mg1−xMnx)2TiO4 (x=0.02–0.1) Solid Solution

Composite ceramics in a solid solution of (Mg_{1− x} Mn _x )₂TiO₄ ( x =0.02–0.1) have been prepared by the mixed oxide route. Formation of the solid solution was confirmed by the X-ray diffraction, the EDX analysis, and the measured lattice parameters, which varied linearly from Mg₂TiO₄ ( a = b = c =8.4410 Å) to (Mg_0.9 Mn_0.1)₂TiO₄ ( a = b = c =8.4445 Å). The XRD analysis also confirmed the co-existence of a cubic-structured (Mg_{1− x} Mn _x )₂TiO₄ and an ilmenite-structured second phase (Mg_{1− x} Mn _x )TiO₃. The composition expected to have a maximum Q × f (276 200 GHz at 10.5 GHz) is (Mg_0.95Mn_0.05)₂TiO₄ with ɛ_r∼15.69 and τ_f∼−52.6 ppm/°C. The existence of the second phase, however, would lead to no significant variation in the dielectric properties of the specimen because it possesses compatible properties compared with that of the main phase.     

Influence of Non-Stoichiometry on the Structure and Properties of Ba(Zn1/3Nb2/3)O3 Microwave Dielectrics: I. Substitution of Ba3W2O9

A narrow region of Zn-vacancy-containing cubic perovskites was formed in the (1− x )Ba₃(ZnNb₂)O₉−( x )Ba₃W₂O₉ system up to 2 mol% substitution ( x =0.02). The introduction of cation vacancies enhanced the stability of the 1:2 B-site ordered form of the structure, Ba(Zn_{1− x} □ _x )_1/3(Nb_{1− x} W _x )_2/3O₃, which underwent an order–disorder transition at 1410°C, ∼35° higher than pure Ba(Zn_1/3Nb_2/3)O₃. The Zn vacancies also accelerated the kinetics of the ordering reaction, and samples with x =0.006 comprised large ordered domains with a high lattice distortion ( c/a =1.226) after a 12 h anneal at 1300°C. The tungstate-containing solid solutions can be sintered to a high density at 1390°C, and the resultant ordered ceramics exhibit some of the highest microwave dielectric Q factors ( Q × f =1 18 000 at 8 GHz) reported for a niobate-based perovskite.     

Phase Transformation and Tunable Piezoelectric Properties of Lead-Free (Na0.52K0.48−xLix)(Nb1−x−ySbyTax)O3 System

Lead-free (Na_0.52K_{0.48− x} )(Nb_{1− x − y} Sb _y )O₃- x LiTaO₃ (NKNS–LT) piezoelectric ceramics have been fabricated by ordinary sintering. A special attention was paid to the composition design through which the dielectric and piezoelectric properties of the (Li, Ta, Sb) modified NKN systems were significantly promoted. A property spectrum was generated with a particular discussion on the relationship between the Sb content, the LT content, the polymorphic phase transition, and the electrical properties and their temperature stability. Excellent and tunable electrical properties of d ₃₃=242–400 pC/N, k _p=36%–54%,     , and T _c=230°–430°C demonstrate a tremendous potential of the compositions studied for device applications.     

Low-Dielectric Loss Characteristics of Nd(Co1/2Ti1/2)O3 Ceramics at Microwave Frequencies

The microwave dielectric properties and the microstructures of Nd(Co_1/2Ti_1/2)O₃ (NCT) ceramics using starting powders of Nd₂O₃, CoO, and TiO₂ prepared by the conventional solid-state route have been researched. The dielectric constant values (ɛ_r) saturated at 24.8–27. Quality factor ( Q × f ) values of 37 900–140 000 (at 9 GHz) and the measured τ_f values ranging from −45 to −48 ppm/°C can be obtained when the sintering temperatures are in the range of 1410°–1500°C. The ɛ_r value of 27, the Q × f value of 140 000 (at 9 GHz) and the τ_f value of −46 ppm/°C were obtained for NCT ceramics sintered at 1440°C for 4 h. For applications of high selective microwave ceramic resonator, filter, and antenna, NCT is proposed as a suitable material candidate.     

Ferroelectric and Piezoelectric Properties of Na1−xBaxNb1−xTixO3 Ceramics

Piezoelectric ceramics Na_{1− x} Ba _x Nb_{1− x} Ti _x O₃ with low BaTiO₃ concentrations x have been prepared by the solid-state reaction method, and their ferroelectric and piezoelectric properties have been studied. The ceramics are classic ferroelectrics when x ≤0.10, and the ferroelectric–paraelectric phase transition becomes diffusive when x ≥0.15. A low doping level of BaTiO₃ changes the NaNbO₃ ceramics from antiferroelectric to ferroelectric. With the increase in BaTiO₃ doping level, the Curie temperature of ceramics decreases linearly and the remnant polarization and coercive field also decrease, while their dielectric constant increases. Na_0.9Ba_0.1Nb_0.9Ti_0.1O₃ ceramics show the largest piezoelectric constant d ₃₃ (147 pC/N) and good sinterability, suggesting that it is a good candidate for lead-free piezoelectric ceramics.     

Modification of MgAl2O4 Microwave Dielectric Ceramics by Zn Substitution

MgAl₂O₄ microwave dielectric ceramics were modified by Zn substitution for Mg, and their dielectric characteristics were evaluated, along with their structures. Dense (Mg_{1− x} Zn _x )Al₂O₄ ceramics were obtained by sintering at 1550°–1650°C in air for 3 h, and the (Mg_{1− x} Zn _x )Al₂O₄ solid solution was determined in the entire composition range. With Zn substitution for Mg, the dielectric constant ɛ of MgAl₂O₄ just varied from 7.90 to 8.56, while the Q × f value had significantly improved up to a maximal value of 106 000 GHz at x =1.0. Moreover, the τ_f of MgAl₂O₄ ceramics had declined from −73 to −63 ppm/°C.     

Structural and Dielectric Properties of Ag(Nb0.8Ta0.2)1−xSbxO3 (x≤0.08) Ceramics

Sb₂O₅ were selected to substitute (Nb_0.8Ta_0.2)₂O₅ and the effects of Sb substitution on the dielectric properties of Ag(Nb_0.8Ta_0.2)O₃ ceramics were studied. The perovskite Ag(Nb_0.8Ta_0.2)_{1− x} Sb _x O₃ ceramics showed no obvious change with x value being no more than 0.08, and the pseudoperovskite unit cell parameters a = c , b and monoclinic angle β decrease with Sb concentration increasing. The dielectric properties of Ag(Nb_0.8Ta_0.2)_{1− x} Sb _x O₃ ceramics were found to be affected greatly by the substitution of Sb for Nb/Ta. The ɛ value of Ag(Nb_0.8Ta_0.2)_{1− x} Sb _x O₃ ceramics sintered at their densified temperature increased from 480 to 825 with x from 0 to 0.08, the tan δ value decreased sharply from 0.0065 to 0.0023 (at 1 MHz) with x increasing from 0 to 0.04, and then kept a stable lower tan δ value ∼0.0024 with x to 0.08. The temperature coefficient of capacitance values continuously decreased from a positive value of 1450 ppm/°C for x =0 to a negative value of −38.52 ppm/°C for x =0.08.