Effect of deep cryotreated tungsten carbide electrode and SiC powder on EDM performance of AISI 304

Abstract

Powder mixed electric discharge machining (PMEDM) is a further advancement of conventional EDM process in which electrically conductive powder is suspended in the dielectric fluid to enhance the material removal rate (MRR) along with the surface quality. Cryotreatment is introduced in this process for improving the cutting tool properties as well as tool life. In this investigation, EDM is performed for the machining of AISI 304 stainless steel using cryotreated double tempered tungsten carbide electrode when SiC powder is suspended in the kerosene dielectric. The influence of process parameters viz. pulse on time, peak current, duty cycle, gap voltage and powder concentration on tool wear rate (TWR), surface roughness (R_a), and MRR has been studied. Metallographic analysis was carried out for the machined surfaces. By the addition of powder concentration and cryotreated double tempered electrode, significant improvement in the machining efficiency has been found out. When cryotreated electrode used MRR, TWR and R_a decreased by 12%, 24% and 13.3%, respectively and when SiC powder used MRR increased by 23.2%, TWR and R_a decreased by about 25% and 14.2%, respectively.     

Experimental investigation of water-in-oil nanoemulsion in sinking electrical discharge machining

The most common dielectric in sinking electrical discharge machining (EDM) is kerosene. However, kerosene is inflammable; besides, it can be decomposed and release harmful gases during machining process. And, owing to its low viscosity, using kerosene in sinking EDM has low machining efficiency. Accordingly, conventional sinking EDM using kerosene as dielectric has poor safety, unfriendly environment impact, and low machining efficiency. A new water-in-oil (W/O) nanoemulsion is presented in this paper. This W/O nanoemulsion not only can eliminate the hazards from kerosene to operator and environment but also improve the machining performance of conventional sinking EDM. This research aims to experimentally investigate the machining performance of W/O nanoemulsion in comparison with kerosene in sinking EDM at relatively low discharge energy. The effects of electrode material, electrode polarity, peak current, and pulse duration on machining performance are studied. The machined surface and recast layer of workpiece are characterized as well. The experimental results demonstrate that compared with kerosene, using W/O nanoemulsion in sinking EDM can obtain a higher material removal rate (MRR), a lower relative electrode wear rate (REWR), and a machined workpiece with fewer defects and thinner recast layer.     

Investigation of the Tool Wear Rate in Tungsten Powder-Mixed Electric Discharge Machining of AA6061/10%SiCp Composite

This paper presents the experimental investigation on tool wear rate (TWR) in powder-mixed electrical discharge machining (PMEDM) of aluminum 6061 alloy reinforced with 10% silicon carbide particles (AA6061/10%SiC_p composite). Composite material is fabricated by mechanical stir casting process and further characterized by scanning electron microscope (SEM) and energy dispersive spectroscopy (EDS). Tungsten powder with concentration of 4 g/L is mixed in the dielectric fluid. To know the influence of powder suspension in dielectric fluid on TWR, comparative study is done on the basis of experiments performed using basic EDM and PMEDM process. Experiments have been designed as per central composite rotatable design (CCRD) using response surface methodology (RSM) approach. Four process parameters, namely, peak current, pulse-on time, pulse-off time, and gap voltage have been considered for TWR investigation. Individual and interactive influence of various parameters on TWR is explained with the help of analysis of variance and three-dimensional graphs. Using RSM approach, results have been further optimized. PMEDM approach provides 51.12% reduction in TWR for machining of AA6061/10%SiC_p composite.     

Influence of graphite powder mixed EDM on the surface integrity characteristics of Inconel 625

Surface integrity in electric discharge machining (EDM) has always been a major concern in the manufacturing industry. Although, EDM with a powder suspended dielectric has shown good potential in enhancing the material removal rate and improving surface finish, influence of the same on the overall surface integrity is not very clear. The current work utilized the graphite powder and evaluated its role in combination with concentration and machining parameters, on surface roughness (Ra), surface crack density (SCD), white layer thickness, microhardness depth profile, possible phase changes, and residual stress during powder-mixed EDM (PMEDM) of Inconel 625 (a nickel-based super alloy), that is now-a-days regularly used in aerospace, chemical and marine industries. The results showed that significant reduction in surface roughness, crack density, and white layer thickness is possible with the PMEDM process. It also promoted formation of carbides and other alloy compounds which is responsible for augmentation of hardness in surface and subsurface region. The added particles also caused a decline in tensile residual stress of the machined samples.     

Electrical Discharge Machining (EDM) Characteristics Associated with Electrical Discharge Energy on Machining of Cemented Tungsten Carbide

In this investigation, cemented tungsten carbides graded K10 and P10 were machined by electrical discharge machining (EDM) using an electrolytic copper electrode. The machining parameters of EDM were varied to explore the effects of electrical discharge energy on the machining characteristics, such as material removal rate (MRR), electrode wear rate (EWR), and surface roughness. Moreover, the effects of the electrical discharge energy on heat-affected layers, surface cracks and machining debris were also determined. The experimental results show that the MRR increased with the density of the electrical discharge energy; the EWR and diameter of the machining debris were also related to the density of the electrical discharge energy. When the amount of electrical discharge energy was set to a high level, serious surface cracks on the machined surface of the cemented tungsten carbides caused by EDM were evident.     

Effect of tool rotation in near-dry EDM process on machining characteristics of HSS

Rotary tool near-dry electrical discharge machining (RT-ND-EDM) is a process variant of EDM, which utilizes two phase dielectric medium instead of a conventional liquid or gaseous dielectric medium. The present work, RT-ND-EDM was investigated while machining of high speed steel (AISI M2 grade) using glycerin-air dielectric medium. The effect of various input process parameters was investigated on material removal rate (MRR), surface roughness (SR), and hole overcut (HOC). The input parameters considered were tool rotation speed, current, pulse on time, liquid flow rate, and gas pressure. Experiments were designed and conducted using response surface methodology. Regression models were also developed. The results revealed that the tool rotation speed has a significant effect on MRR, SR, and HOC. FE-SEM micrographs showed that the machined surfaces obtained by RT-ND-EDM have relatively lower micro-cracks, debris accumulation and craters. Also, deep through holes were successfully drilled in 24 mm plate using RT-ND-EDM process.     

The Feasibility Analysis of Electrical-Discharge Machining of Carbon-Carbon Composites

The objective of this research is to investigate the feasibility of using Electrical-Discharge Machining (EDM) for carbon-carbon composite materials as well as the effects of major machining parameters. The material was machined by electrical-discharge sinker using copper electrode. The mechanism of material removal has been revealed by the morphology of debris. The material removal rate, the surface topography and the recast layer that remains on the workpiece surface were studied in terms of EDM processing variables (e.g., pulse current and pulse duration time). The machined surface showing resolidification was examined by Scanning Electron Microscopy (SEM). A qualitative energy dispersive spectroscopic analyzer was used to measure the amount of migrated alloy in the workpiece and the chemical composition of recast layer. The machining damage, the recast layer, and the mass transfer was proportional to the power input. The EDM process is a feasible method for machining of carbon-carbon composites.     

Effect of electrical discharge machining on the characteristics of carbon fiber reinforced carbon composites

This work investigated electrical discharge machining (EDM) of carbon fiber reinforced carbon composite material. The characteristics of composites machined by EDM were studied in terms of machining parameters. An empirical model of the composites was also proposed based on the experimental data. The composite material was produced by an electrical discharge sinker using a graphite electrode. The workpiece surface and resolidified layers were examined by scanning electron microscopy (SEM). Moreover, surface roughness was determined with a surface profilometer. Experimental results indicate that the extent of delamination, thickness of the recast layer, and surface roughness are proportional to the power input. The EDM process effectively produces excellent surface characteristics and high quality holes in composites under low discharge energy conditions.     

Performance analysis of magnetorheological fluid-assisted electrical discharge machining

In this study, a newly developed method of electric discharge machining has been proposed, which uses magnetorheological (MR) fluid instead of conventional oil like kerosene. The paper aims to reveal the process parameters that affect the material removal rate (MRR) during newly developed EDM process. This hybrid machining process showed dual advantage of high-quality machined surface with improved cutting efficiency. The viscoelastic nature of MR fluid is found to give polishing effect as well as high material removal resulting in more stable processing and improved EDM performance. The experimentation has been performed to determine effect of duty cycle, discharge current, pulse on time, percentage concentration of alumina particles surface roughness, and MRR. It has been found that MRR and surface finish improved significantly. The experimental results demonstrated that the EDM process combined with MR fluid resulted in an increase in MRR and surface finish significantly under a certain limit of carbonyl iron percentage (CIPs) in MR fluid.     

Parametric Evaluation on Near-Dry Electric Discharge Machining

Near-dry electric discharge machining (EDM) is an eco-friendly process. It does not produce toxic fumes and consequent health hazards. The near-dry EDM generally utilizes a mixture of two phase (liquid and air) dielectric for machining. This investigation reports the influence of four processing parameters, viz. current, flushing pressure, duty factor, and lift on three responses. The responses measured were material removal rate (MRR), tool wear rate (TWR), and surface roughness (SR). The work material chosen was high speed steel (HSS). Mathematical models have been proposed herein for evaluation of the effect of processing parameters in near-dry EDM. These models were developed using response surface methodology (RSM). The experimental results reveal that the process parameters taken into consideration were significant for MRR. The TWR was negligible in near-dry EDM. This process gives a finer surface finish with thinner recast layer even at higher discharge energies as compared to conventional EDM.     

An Experimental Study on Electrical Discharge Machining of Manganese-Zinc Ferrite Magnetic Material

The objective of this research is to investigate the machining characteristics of manganese-zinc (Mn-Zn) ferrite magnetic material using electrical-discharge machining (EDM). The material removal rate, the surface topography, the surface roughness, the recast layer, and the chemical composition of the machined surface were studied in terms of EDM processing variables. Experimental results indicate that the morphology of debris revealed the mechanism of material removal. The surface microgeometry characteristics are not always uniform and homogenous and the EDM process produces much damage on the machined surface. The material removal rate, the surface roughness, and the recast layer are proportional to the applied discharge energy.     

Parametric optimization of multiwalled carbon nanotube-assisted electric discharge machining of Al-10%SiCp metal matrix composite by response surface methodology

The demand for miniaturized products having a glossy surface or nano-level surface is increasing exponentially in automobile, aerospace, biomedical, and semiconductor industries. The mirror-like surface finish has generated a need to develop advanced machining processes. The addition of powder particle into electric discharge machining (EDM) oil is considered a promising technique to achieve surface integrity at the miniaturization level. In this research, the Al–10%SiC_p metal matrix composite (MMC) has been machined after mixing the appropriate amount of multiwalled carbon nanotubes (MWCNTs) into the EDM dielectric fluid. An advanced experimental setup has been designed and fabricated in the laboratory for conducting the experiments. This proposed technology is called nano powder mixed electric discharge machining (NPMEDM). The input parameters of NPMEDM are also optimized using central composite rotatable design (CCRD) based on response surface methodology (RSM) in order to obtain the best surface finish and material removal rate (MRR). The MRR has been increased by 38.22% and surface finish has been improved by 46.06% after mixing the MWCNTs into the EDM dielectric fluid. The results indicate that the combination of parameters A5, B5, C5, and D5 might have produced maximum MRR, whereas A1, B1, C1, and D3 have produced minimum surface roughness (SR).     

Experimental investigations in powder mixed electric discharge machining of Ti–35Nb–7Ta–5Zrβ-titanium alloy

The present research is the first type of study in which the application of powder mixed electrical discharge machining (PMEDM) for the machining of β-phase titanium (β-Ti) alloy has been proposed. β-Ti alloys are new range of titanium alloys, which has a wide-spread application in dental, orthopedics, shape memory, and stents. The aim of the present study is to fabricate submicro- and nanoscale topography by PMEDM process to enhance the biocompatibility without affecting machining efficiency. The effect of Si powder concentration along with pulse current and duration on the surface and machining characteristics has been investigated. A significant decrease in surface crack density on the machined surface with 4 g/l Si powder concentration was observed. When β-Ti alloy was modified at 15 A pulse current, longer pulse interval with 8 g/l concentration of Si powder particles, the interconnected surface porosities with pore size 200–500 nm was observed. Moreover, at Si powder concentrations of 2 g/l and 4 g/l, the recast layer thickness is 8 µm and 2–3 µm, respectively. Elemental mapping analysis confirmed that PMEDM also generated carbides and oxides enriched surface, a favorable surface chemistry to enhance the biocompatibility of β-Ti alloy. Furthermore, PMEDM also enhances the machining performance by improving material removal rate and reducing tool wear rate.     

Evaluation of WEDM performance characteristics of Inconel 706 for turbine disk application

Inconel 706 is a newly developed superalloy, which offers high mechanical strength alongwith easy fabricability thus making it suitable for turbine disk applications. Although Inconel 706 exhibits a substantial increase in stress rupture and tensile yield strength compared to other superalloys, its conventional machining yields poor surface finish and low dimensional accuracy of the machined components. Hence, wire electrical discharge machining (WEDM) of Inconel 706 has been performed and various performance attributes such as material removal rate (MRR), surface roughness (SR), recast surface, topography, microhardness, microstructural and metallurgical changes of the machined components have been evaluated. The experimental results revealed that servo voltage, pulse on time, and pulse off time greatly influence the MRR and SR. Due to high toughness of Inconel 706, no micro cracks were observed on the machined surface. Micro voids and micro globules are significantly reduced at low pulse on time and high servo voltage. But, there is a propensity of thick recast layer formation at high pulse on time and low servo voltage. EDAX analysis of recast surface exposed the existence of Cu and Zn which have migrated from the brass wire. The subsurface microhardness was changed to 80 μm due to significant thermal degradation.     

Powder Mixed Dielectric: An Approach for Improved Process Performance in EDM

The present study reports the outcome of experiments conducted to investigate the effect of parameters on improvement in the material removal rate (MRR), reduction in the tool wear rate (TWR), and overcut size for commonly used die steels. To overcome some of the shortcomings of electric discharge machining (EDM), an approach of powder mixing in dielectric fluids is adopted to investigate the influence of process parameters. The addition of powders in dielectric improves MRR and lowers TWR significantly. Powder concentration, current, and pulse-on time are three significant factors affecting MRR, TWR, and overcut size. An increase in powder concentration improves the process performance, but is limited by the possibility of arcing at higher concentration. Use of the powder resulted in increased effective spark length causing larger overcut. The problem is acute in trials conducted at high pulse-on duration with high powder concentration that leads to a ragged surface at cut edges. Furthermore, electrode tools with smaller tip included angle resulted in larger profile deviation at the machined surface as compared to trials conducted using tools with higher included angle. Surface morphological changes, grain size, microstrain, and material migration were investigated using SEM, XRD, and EDS analysis and a significant improvement in properties of the machined surface was observed.     

Examinations concerning the electric discharge machining of AZ91/5B4CP composites utilizing distinctive electrode materials

In this study, investigation has been conducted in the focus of obtaining better surface finish in the electro discharge machining (EDM) of AZ91/5B₄C_p magnesium composites using distinctive sort of anode viz. copper, tungsten–copper, brass, aluminum and 20Gr/AA6061 (GRAL-20) composites. The process parameters, pulse on time and current were performed to research the machining qualities through material removal rate (MRR) and tool wear rate (TWR). The machined composites were examined by optical microscopy (OM) and scanning electron microscopy (SEM). The formation of black spots was observed on machining with copper–tungsten and these black spots were not found when GRAL-20 was used as electrode. Machined with GRAL-20 electrode leads to the increase in spark gap, hence adequate flushing occurs; it eliminates re-melted layers on machined surface results in better surface roughness value. The results revealed that GRAL-20 electrodes posses better MRR followed by copper electrode whereas tungsten–copper exhibits better TWR followed by GRAL-20 electrode.     

Improving the machining performance characteristics of the µEDM drilling process by the online cryogenic cooling approach

Productivity and surface quality would significantly affect the performance of the micro electrical discharge machining process (µEDM). Thus, the machining performance would be enhanced by improving the material removal rate (MRR) and surface quality. In this investigation, cryogenic LN₂ cooling was introduced to the conventional µEDM setup for developing an innovative process of cryogenically cooled µEDM process (CµEDM). The favorable outcomes of this process were estimated by selecting discharge current (I_p) and pulse on duration (T_on) for determining the effects of the machining performance including MRR and surface integrity. Surface quality was also analyzed by microstructural analysis and a scanning electron microscope (SEM) for evaluating the effects of the cryogenically cooled µEDM process. The experimental result shows 54–62% improvement in MRR and 22–36% improvement in average roughness values. Hence, it is suggested that cryogenically cooled µEDM facilitates improvement in productivity and surface quality.     

Performance of Additive Mixed Kerosene–Servotherm in Electrical Discharge Machining of Monel 400™

In general, kerosene and commercial grade EDM oils are conventional dielectric fluids in electrical discharge machining (EDM), despite their poor performance measures being major drawbacks. The aim of this study was to develop a dielectric fluid offering good performance measures in the EDM process, by determining the appropriate proportion of kerosene–servotherm and analyzing its performance with and without the additive concentration in EDM of monel 400?. Sixteen samples of kerosene–servotherm of varying proportions were used in this study. The optimum proportion of kerosene–servotherm was found to be 75:25, which resulted in the highest material removal rate (MRR) as compared with tool wear rate (TWR), and surface finish was found to be poorer than when using kerosene alone. In addition, 1 l of kerosene–servotherm concentrated with 6 g of graphite powder (one micron) exhibited substantial improvement in MRR, surface finish, and TWR compared with conventional dielectric fluids. Therefore kerosene–servotherm (75:25) concentrated with 6 g/l of graphite powder can be accepted as a potential dielectric fluid offering high MRR along with enhanced surface finish in EDM.     

Effect of Tool Rotation on MRR,TWR, and Surface Integrity of AISI-D3 Steel using the Rotary EDM Process

Electric discharge machining (EDM) is an acclaimed non-conventional machining process that is used for machining of hard or geometrically complex and electrically conductive materials which are extremely difficult to machine by conventional methods. One of the foremost demerits of this process is its very low material removal rate (MRR). For this, researchers have proposed some modifications like; providing rotational motion to the tool or workpiece, mixing of conducting fine powders (such as SiC, Cr, Al, graphite etc.) in the dielectric, providing vibrations to either the tool or the workpiece etc.

The present research examines how the MRR and tool wear rates (TWR) vary with the variation in the tool rotation speed and their effects on the surface integrity of the workpiece. The results obtained clearly indicate that the tool rotation significantly improves the average MRR up to 49%. Moreover, the average surface finish also gets improved by around 9–10% while using the rotational tool EDM. Due to the tool rotation, the recast layer thickness is less for the rotary EDM as compared with the stationary tool EDM process. Furthermore, the micro-cracking on the recast surface of the workpiece is also less for the rotary tool EDM as compared with the stationary tool EDM.     

Effect of electrical discharge machining process on crack susceptibility of nickel based heat resistant alloy

Abstract

The objective of this study was to investigate the effects of electrical discharge machining (EDM) process conditions on the crack susceptibility of a nickel-based superalloy. Because sequential processes are inevitable in the manufacturing industry, the effects of EDM and post-EDM processes on the crack propagation behaviour of the components need to be clearly understood. The altered material zone (AMZ) of EDM processed Hastelloy X revealed different morphology before and after solution heat treatment. Depending on the EDM dielectric fluid and the post-EDM process such as solution heat treatment, it was found that cracks existing in the recast layer could propagate into substrate when a 20% strain tensile force was applied at room temperature. In the case of the kerosene electrical discharge (ED) machined specimens, it was observed that carburisation and sharp crack propagation along the grain boundary occurred after the heat treatment. However, the deionised water ED machined specimens after heat treatment underwent oxidation and showed no crack propagation behaviour. A metallurgical evaluation of the microstructure of the AMZ was also conducted.