Microstructural and Magnetic Features of SrFe<Subscript>12</Subscript><Emphasis Type="Italic">O</Emphasis><Subscript>19</Subscript> Materials Synthesized from Different Fuels by Sol-Gel Auto-Combustion Method

The nanocrystalline SrFe₁₂ O ₁₉ materials were prepared by a sol-gel auto-combustion method using different fuels such as citric acid, dextrose, aniline, and hexamine. The combustion product obtained from all the fuels except from that of aniline show a single phase of SrFe₁₂ O ₁₉ materials upon annealing at 1000 ^°C/2 h. The combustion product obtained from aniline as fuel shows SrFe₁₂ O ₁₉ as the main phase with α-Fe₂ O ₃ as impurity. No notable change in lattice parameters is observed due to variation in fuels for SrFe₁₂ O ₁₉ materials. With a little change in the NIR relative reflectance (72–85 %) on fuels, the different SrFe₁₂ O ₁₉ materials display high NIR reflectance in the wavelength range, 1500–2500 nm. The photoluminescence emission spectra of SrFe₁₂ O ₁₉ materials reveal a broad emission peak at ～350 nm which is reminiscent to the Ba-based hexaferrite, BaFe₁₂ O ₁₉. The FESEM images expose quite dissimilar morphology for the various fuels used in the synthesis of SrFe₁₂ O ₁₉ materials. Hysteresis loops for all the nanocrystalline SrFe₁₂ O ₁₉ materials observed under the applied field of ±1.5 T at room temperature exhibit hard ferromagnetic property. The SrFe₁₂ O ₁₉ materials produced from glycine and aniline as fuels exhibit highest and lowest M _s values of 61.3 and 50.5 emu/g, respectively.     

Improvement of the Magnetization of Barium Hexaferrites Induced by Substitution of Nd<Superscript>3+</Superscript> Ions for Fe<Superscript>3+</Superscript> Ions

Barium hexagonal ferrites (BaNd _x Fe_12?x O ₁₉) have been synthesized by initial high-energy milling of the precursors and calcining subsequently. The as-prepared samples are characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), and vibrating sample magnetometry (VSM). XRD and SEM examinations reveal that a high-crystallized hexagonal BaNd _x Fe_12?x O ₁₉ with lamellar morphology is obtained when the precursor is calcined at 1200^°C in air for 3 h. The hexagonal crystalline structure of BaFe₁₂ O ₁₉ is not changed after doping Nd³⁺ ions in BaFe₁₂ O ₁₉. However, lattice parameters a and b values increase with an increase in Nd content at first, then decrease. Nd substitution may improve the magnetic properties of BaNd _x Fe_12?x O ₁₉. BaNd_0.1Fe_11.9 O ₁₉, obtained at 1050^°C, has the highest specific saturation magnetization value (80.81 emu/g) and magnetic moment (16.21 μ _B); BaNd_0.2Fe_11.8 O ₁₉, obtained at 950^°C, has the highest coercivity value, 4075.19 Oe.     

Superconducting Performance,Structure, Microstructure,and Trapped Field of Top-Seeded Melt-Processed Bulk Y<Subscript>3</Subscript>Ba<Subscript>5</Subscript>Cu<Subscript>8</Subscript>O<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>

The sintering temperature for the production of Y₃Ba₅Cu₈O₁₈ (Y-358) preform powders synthesized in sol-gel spontaneous combustion technique was optimized. A large single-grain bulk Y-358 crystal was fabricated employing a top-seeded melt-growth technique utilizing the optimally sintered preform powders (i.e., at 900 ^°C for 12 h). Structural, microstructural, elemental, and magnetic properties were investigated by means of X-ray diffraction, scanning electron microscopy, and SQUID, respectively. The structural characterization indicated that the sample is highly textured in (00l) direction. The Y-358 phase fractions were estimated in both preform powders and bulk sample using Rietveld refinement. The onset of superconducting transition is observed at 92.5 K, and the curve is very sharp indicative of the high quality of the produced bulk sample. The field dependence of critical current density (J_c) was determined at 77 K, and the self-field J_c was found to be ～26 kA/cm². A magnetic field of 0.27 T was trapped by the sample at 77 K.     

Synthesis and luminescence properties of Tb<Superscript>3+</Superscript>-doped LiMgPO<Subscript>4</Subscript> phosphor

Polycrystalline sample LiMg_(1?x)PO₄:xTb³⁺ (x = 0.001, 0.002, 0.005, 0.01, 0.02) phosphor was synthesized via modified solid state method (MSSM). The prepared sample was characterized through XRD pattern (X-ray diffraction) and SEM (scanning electron microscope). Additionally, photoluminescence (PL), optically stimulated luminescence (OSL), thermoluminescence (TL) and other dosimetric properties including dose linearity, reusability and fading were studied. In OSL mode, sensitivity of prepared phosphor was found to be 2.7 times that of LiMgPO₄:Tb³⁺, B (BARC) phosphor and 4.3 times that of α-Al₂O₃:C (BARC) phosphor. The TL glow consists of overlapping peaks in temperature range of 50–400^°C and first peak (P₁) was observed at 150^°C, second peak (P₂) at 238^°C, third peak (P₃) at 291^°C and fourth peak (P₄) at 356^°C. The TL sensitivity of second peak (P₂) of LiMgPO₄:Tb³⁺ phosphor was compared with α-Al₂O₃:C (BARC) phosphor and found to be 100 times that of the α-Al₂O₃:C (BARC) phosphor. The minimum detectable dose (MDD) was found to be 5.6 μGy. Moreover, photoionization cross-sections, linearity, reusability, fading and kinetic parameters were calculated. Also, photoluminescence spectra of LiMgPO₄: Tb³⁺ shows characteristic green–yellow emission exciting at 224 nm UV source.     

Fe<Subscript>73.5</Subscript>Cu<Subscript>1</Subscript>Nb<Subscript>3</Subscript>Si<Subscript>15.5</Subscript>B<Subscript>7</Subscript> Thin Films Deposited by HiPIMS: Magnetic and Magnetostrictive Behavior

Results concerning the magnetic, magnetostrictive, structural, morphological, and topological properties of amorphous and nanocrystalline Fe _73.5Cu ₁Nb ₃Si _15.5 B ₇ thin films deposited using the high power impulse magnetron sputtering (HiPIMS) technique are reported. In as-deposited state, the samples are amorphous, the nanocrystalline state being achieved for samples isothermally annealed at adequate temperatures, in an electric furnace. For the optimum annealing temperature (475 ^°C), a decrease by about 70 % for the coercive magnetic field (50 A/m) and up to 1 order of magnitude for the saturation magnetostriction (~1×10^?6), compared to the as-deposited state, was obtained. The X-ray diffractometry (XRD) and scanning electron microscopy (SEM) results for samples thermally treated at 475 ^°C revealed a 53.6 % crystalline volume fraction of α-Fe(Si) nanograins with an average size of about 15 nm and a Si content of 10.78 %, uniformly dispersed in a residual amorphous matrix. Using the saturation magnetostriction values determined using the cantilever deflection method and the crystalline volume fraction of α-Fe(Si) nanograins, the contribution of crystalline phase to the saturation magnetostriction was also determined.     

Low temperature sintering and microwave dielectric properties of Li<Subscript>6</Subscript>Mg<Subscript>7</Subscript>Ti<Subscript>3</Subscript>O<Subscript>16</Subscript> ceramics with LiF additive for LTCC applications

Li₆Mg₇Ti₃O₁₆ ceramics were prepared by the conventional solid-state method with 1–5 wt% LiF as the sintering aid. Effects of LiF additions on the phase compositions, sintering characteristics, micro-structures and microwave dielectric properties of Li₆Mg₇Ti₃O₁₆ ceramics were investigated. The LiF addition could effectively lower the sintering temperature of Li₆Mg₇Ti₃O₁₆ ceramics from 1550 to 900 °C. For different LiF-doped compositions, the optimum dielectric permittivity (ε _r ) and quality factor (Q·f) values first increased and then decreased with the increase of LiF contents, whereas the temperature coefficient of resonant frequency (τ _f ) fluctuated between ??14.39 and ??8.21 ppm/°C. Typically, Li₆Mg₇Ti₃O₁₆ ceramics with 4 wt% LiF sintered at 900 °C exhibited excellent microwave dielectric properties of ε _r ?=?16.17, Q·f?=?80,921 GHz and τ _f ?=???8.21 ppm/°C, which are promising materials for the low temperature co-fired ceramics applications.     

Very high thermal stability with excellent dielectric,and non-ohmics properties of Mg-doped CaCu<Subscript>3</Subscript>Ti<Subscript>4.2</Subscript>O<Subscript>12</Subscript> ceramics

In this work, the nominal CaCu_3?xMg_xTi_4.2O₁₂ (0.00, 0.05 and 0.10) ceramics were prepared by sintering pellets of their precursor powders obtained by a polymer pyrolysis solution method at 1100 °C for different sintering time of 8 and 12 h. Very low loss tangent (tanδ)?<?0.009–0.014 and giant dielectric constant (ε′) ～?1.1?×?10⁴–1.8?×?10⁴ with excellent temperature coefficient (Δε′) less than ±?15% in a temperature range of ??60 to 210 °C were achieved. These excellent performances suggested a potent application of the ceramics for high temperature X8R and X9R capacitors. It was found that tanδ values decreased with increasing Mg²⁺ dopants due to the increase of grain boundary resistance (R_gb) caused by the very high density of grain, resulting from the substitution of small ionic radius Mg²⁺ dopants in the structure. In addition, CaCu_3?xMg_xTi_4.2O₁₂ ceramics displayed non-linear characteristics with the significant enhancements of a non-linear coefficient (α) and a breakdown field (E_b) due to Mg²⁺doping. The high values of ε′ (14012), α (13.64) and E_b (5977.02 V/cm) with very low tanδ value (0.009) were obtained in a CaCu_2.90Mg_0.10Ti_4.2O₁₂ ceramic sintered at 1100 °C for 8 h.     

Critical Behavior of La<Subscript>0.67</Subscript>Ba<Subscript>0.33</Subscript>Mn<Subscript>0.95</Subscript>Fe<Subscript>0.05</Subscript>O<Subscript>3</Subscript> Manganite

The critical behavior of perovskite manganite La_0.67Ba_0.33Mn_0.95Fe_0.05O₃ at the ferromagnetic–paramagnetic has been analyzed. The results show that the sample exhibited the second-order magnetic phase transition. The estimated critical exponents derived from the magnetic data using various such as modified d’Arrott plot Kouvel–Fisher method and critical magnetization M(T _C, H). The critical exponents values for the La_0.67Ba_0.33Mn_0.95Fe_0.05O₃ are close to those expected from the mean field model β = 0.504 ± 0.01 with T _C = 275661 ± 0.447 (from the temperature dependence of the spontaneous magnetization below T _C ), γ = 1.013 ± 0.017 with T _C = 276132 ± 0.452 (from the temperature dependence of the inverse initial susceptibility above T _C ), and δ = 3.0403 ± 0.0003. Moreover, the critical exponents also obey the single scaling equation of M(H, ε) = |ε| ^β f _±(H/|ε| ^β+γ ).     

Synthesis and structure of the CsSmP<Subscript>4</Subscript>O<Subscript>12</Subscript> cyclotetraphosphate (cubic CsNdP<Subscript>4</Subscript>O<Subscript>12</Subscript> structure)

CsSmP₄O₁₂ crystals have been prepared at 300°C in molten polyphosphoric acids containing Cs, Mg, and Sm cations, and their crystal structure has been determined: sp. gr. I \(\bar 4\) 3d, a = 15.1225(8) Å, Z = 12, CsNdP₄O₁₂ structure.     

Low temperature sintering and microwave dielectric properties of Zn<Subscript>3</Subscript>Mo<Subscript>2</Subscript>O<Subscript>9</Subscript> ceramic

Crystal structure and dielectric properties of Zn₃Mo₂O₉ ceramics prepared through a conventional solid-state reaction method were characterized. XRD and Raman analysis revealed that the Zn₃Mo₂O₉ crystallized in a monoclinic crystal structure and reminded stable up to1020 °C. Dense ceramics with high relative density (~ 92.3%) were obtained when sintered at 1000 °C and possessed good microwave dielectric properties with a relative permittivity (ε _r ) of 8.7, a quality factor (Q?×?f) of 23,400 GHz, and a negative temperature coefficient of resonance frequency (τ _f ) of around ??79 ppm/°C. With 5 wt% B₂O₃ addition, the sintering temperature of Zn₃Mo₂O₉ ceramic was successfully lowered to 900 °C and microwave dielectric properties with ε _r ?=?11.8, Q?×?f?=?20,000 GHz, and τ _f = ??79.5 ppm/°C were achieved.     

Crystal structure,microstructure and microwave dielectric properties of novel MgAl<Subscript>2</Subscript>Ti<Subscript>3</Subscript>O<Subscript>10</Subscript> ceramic

In the present work, a novel MgAl₂Ti₃O₁₀ ceramic was obtained using a traditional solid-state reaction method. X-ray diffraction and energy dispersive spectrometer showed that the main MgAl₂Ti₃O₁₀ phase was formed after sintered at 1300–1450 °C. With rising the sintering temperature from 1300 to 1450 °C, the bulk density (ρ), relative permittivity (ε _r ) and Q?×?f value firstly increased, reached the maximum values (3.61 g/cm³, 14.9, and 26,450 GHz) and then decreased. The temperature coefficient of resonator frequency (τ _f ) showed a slight change at a negative range of ??94.6 to ??83.7 ppm/°C. When the sintering temperature was 1400 °C, MgAl₂Ti₃O₁₀ ceramics exhibited the best microwave dielectric properties with Q?×?f?=?26,450 GHz, ε _r ?=?14.9 and τ _f ?=???83.7 ppm/°C.     

Ultralow thermal conductivity of cerium-doped Nd<Subscript>2</Subscript>Zr<Subscript>2</Subscript>O<Subscript>7</Subscript> over a wide doping range

In this paper, we report an ultralow thermal conductivity and a high-temperature phase stability of the (Nd_1?x Ce _x )₂Zr₂O_7+x system over the temperature range from room temperature to 1600 °C and over a wide composition range (0.2 ≤ x ≤ 0.8), and the (Nd_1?x Ce _x )₂Zr₂O_7+x system is therefore considered a strong candidate material for the fabrication of next-generation high-temperature thermal barrier coatings. The observed thermal conductivities (0.65–1.0 W/mK) are about 60–40% lower than those of undoped Nd₂Zr₂O₇ over the same temperature range (100–700 °C) and indicate a glass-like behavior. For comparison, the variation in the thermal conductivity with the temperature of the (Gd_1?x Ce _x )₂Zr₂O_7+x system with similar point defects was also measured, and the observed behavior was almost the same as that of undoped Gd₂Zr₂O₇ and was mostly determined by phonon–phonon scattering (λ ∝ 1/T). The effect of point defect scattering and strong phonon scattering sources (rattlers) on the thermal conductivity is also discussed in this paper. The results of this study suggest that the ultralow thermal conductivity of (Nd_1?x Ce _x )₂Zr₂O_7+x can be attributed to the presence of rattlers because of the large difference between the ionic radii of the Nd³⁺ and Ce⁴⁺ ions.     

Solid-state reactions in the system Li<Subscript>2</Subscript>CO<Subscript>3</Subscript>-Na<Subscript>2</Subscript>CO<Subscript>3</Subscript>-Nb<Subscript>2</Subscript>O<Subscript>5</Subscript>-Ta<Subscript>2</Subscript>O<Subscript>5</Subscript>

The formation mechanisms of Li _x Na_{1 ?x} Ta _y Nb_{1 ? y} O₃ perovskite solid solutions in the Li₂CO₃-Na₂CO₃-Nb₂O₅-Ta₂O₅ system have been studied by x-ray diffraction, differential thermal analysis, thermogravimetry, IR spectroscopy, and mass spectrometry at temperatures from 300 to 1100°C. The results indicate that the synthesis of Li _x Na_{1 ? x} Ta _y Nb_{1 ? y} O₃ solid solutions involves a complex sequence of consecutive and parallel solid-state reactions. An optimized synthesis procedure for Li _x Na_{1 ? x} Ta _y Nb_{1 ? y} O₃ solid solutions is proposed.     

Thermodynamic properties of SrAl<Subscript>12</Subscript>O<Subscript>19</Subscript> and SrAl<Subscript>4</Subscript>O<Subscript>7</Subscript>

Strontium aluminates are important compounds with interesting properties such as long-duration phosphorescence and elastico-deformation luminescence. They have potential application in flexible light emitting panels. Since there are serious discrepancies in available thermodynamic data for these compounds, a redetermination of their Gibbs energies of formation was undertaken using solid-state electrochemical cells incorporating single-crystal SrF₂ as the electrolyte in the temperature range from 1000 to 1300 K. However, the measurements were restricted to SrAl₁₂O₁₉ and SrAl₄O₇ because of the formation of strontium oxyfluoride phase between SrAl₂O₄ and SrF₂. For the reactions, SrO + 6 Al₂O₃ → SrAl₁₂O₁₉, ΔG ^o/J mol^?1 (± 280) = ?83386 ? 25.744 (T/K), and SrO + 2Al₂O₃ → SrAl₄O₇, ΔG ^o/J mol^?1 (± 240) = ?80187 ? 25.376 (T/K). The high entropy of SrAl₄O₇ and SrAl₁₂O₁₉ can be partly related to their complex structures. The results of this study are consistent with calorimetric data on enthalpy of formation of other Sr-rich aluminates and indicate only marginal stability for SrAl₄O₇ relative to its neighbours, SrAl₁₂O₁₉ and SrAl₂O₄. The thermodynamic data explain the difficulty in direct synthesis of phase pure SrAl₄O₇ and the formation of SrAl₂O₄ as the initial ternary phase when reacting SrO and Al₂O₃ or crystallizing from amorphous state, irrespective of composition.     

Structural and dielectric properties of PbMg<Subscript>1/3</Subscript>Nb<Subscript>2/3</Subscript>O<Subscript>3</Subscript>-PbZrO<Subscript>3</Subscript> solid solutions synthesized at high pressures and temperatures

(1 ? x)PbMg_1/3Nb_2/3O₃ · xPbZrO₃ (1 ? x)PMN · xPZ) solid solutions have been synthesized at a pressure of 5 GPa and temperatures from 1300 to 1700 K, and their structural and dielectric properties have been studied. The composition dependences of the average unit-cell parameter and dielectric permittivity for the solid solutions indicate that the PMN-PZ system has a morphotropic phase boundary near x = 0.65. The solid solutions have a cubic structure for x < 0.65, a rhombohedral structure in the range 0.65 < x < 0.9, and an orthorhombic structure (similar to that of PbZrO₃) for x > 0.9. The temperature and frequency dependences of dielectric permittivity suggest that the (1 ? x)PMN · xPZ samples with x < 0.65 consist of two ferroelectric phases: a relaxor with antipolar dipole order and a normal ferroelectric with a diffuse phase transition. The effect of annealing temperature on the ferroelectric state of the samples with x < 0.65 is examined. In the composition range 0.65 < x < 0.9, the samples have normal ferroelectric properties, independent of annealing temperature.     

The calorimetry and thermodynamic functions of Nd Mg<Stack><Subscript>3</Subscript><Superscript>I</Superscript></Stack>Mn<Subscript>4</Subscript>O<Subscript>12</Subscript> (Me<Superscript>I</Superscript>-Li,Na, K) manganites in the range from 298.15 to 673 K

The ceramic technology is employed for synthesizing manganites of composition Nd Mg ₃ ^I Mg₃Mn₄O₁₂(Me^I-Li, Na, K). The X-ray technique is used to find that the compounds crystallize in tetragonal syngony. The parameters of their crystal lattices are determined. Their heat capacities are experimentally determined in the range from 298.15 to 673 K, which enables one to reveal second-order phase transitions. In view of these transitions, equations describing the C _p ^° ～ f(T) dependence are derived, and the thermodynamic functions C _p ^° (T), H°(T)-H°(298.15), S°(T), and Φ ^xx (T) are calculated.     

New,thermally stable Gd<Subscript>11</Subscript>(GeO<Subscript>4</Subscript>)(PO<Subscript>4</Subscript>)<Subscript>3</Subscript>O<Subscript>10</Subscript>-based upconversion phosphors

A series of Gd_11–x–y Yb _x Er _y GeP₃O₂₆ germanate phosphates differing in the ratio of the Yb³⁺ and Er³⁺ active ions have been synthesized, and their luminescence spectra have been measured. According to X-ray diffraction characterization results, all of the synthesized germanate phosphates are single-phase and have a triclinic structure (sp. gr. P1). We have measured upconversion luminescence spectra due to the Er^{3+ 2}H_11/2, ⁴S_3/2 → ⁴I_15/2 and ⁴F_9/2 → ⁴I_15/2 radiative transitions in the synthesized gadolinium ytterbium erbium germanate phosphates and determined the luminescence upconversion energy yield (B _en) in Gd_11–x–y Yb _x Er _y GeP₃O₂₆. The effects of the concentrations and ratio of the dopants in the Gd₁₁(GeO₄)(PO₄)₃O₁₀ germanate phosphate host on B _en and the ratio of the luminescence intensities in the red and green spectral regions (R/G) have been assessed.     

Compounds WAl<Subscript>4</Subscript>, WAl<Subscript>3</Subscript>, W<Subscript>3</Subscript>Al<Subscript>7</Subscript>, and WAl<Subscript>2</Subscript> and Al-W-N combustion products

X-ray diffraction data are presented for combustion products in the Al-W-N system. New, nonequilibrium intermetallic compounds have been identified, their diffraction patterns have been indexed, and their unit-cell parameters have been determined. The phases α-and β-WAl₄ are shown to exist in three isomorphous forms, differing in unit-cell centering. The phases α′-, α″-, and α?-WAl₄ are monoclinic, with a ₀ = 5.272 Å, b ₀ = 17.770 Å, c ₀ = 5.218 Å, β = 100.10°; point groups C12/c1, A12/n1, I12/a1, respectively. The phases β′-, β″-, and β?-WAl₄ are monoclinic, with a ₀ = 5.465 Å, b ₀ = 12.814 Å, c ₀ = 5.428 Å, β = 105.92°; point groups A112/m, B112/m, I112/m, respectively. The compounds WAl₂ and W₃Al₇, identified each in two isomorphous forms, differ in cell metrics (doubling) but possess the same point group: P222. WAl ₂ ^′ : orthorhombic, a ₀ = 5.793 Å, b ₀ = 3.740 Å, c ₀ = 6.852 Å. WAl ₂ ^″ : orthorhombic, a ₀ = 11.586 Å, b ₀ = 3.740 Å, c ₀ = 6.852 Å. W₃Al ₇ ^′ : orthorhombic, Pmm2, a ₀ = 6.225 Å, b ₀ = 4.806 Å, c ₀ = 4.437 Å. W₃Al ₇ ^″ : orthorhombic, Pmm2, a ₀ = 12.500 Å, b ₀ = 4.806 Å, c ₀ = 8.874 Å. The new phase WAl₃: triclinic, P1, a ₀ = 8.642 Å, b ₀ = 10.872 Å, c ₀ = 5.478 Å, α = 104.02°, β = 64.90°, γ = 107.15°.     

The magnetic properties of BiY<Subscript>2</Subscript>Fe<Subscript>5</Subscript>O<Subscript>12</Subscript> nanoparticles doped with Cr ions

BiY₂Cr _x Fe_5?x O₁₂ (x = 0, 0.05, 0.1, 0.2, 0.3) nanocrystals were synthesized by using a sol-gel method. Samples were characterized by the powder X-ray diffraction (XRD), the thermal gravity analysis (TGA) and the differential thermal analysis (DTA), the vibrating sample magnetometer(VSM) and Mössbauer spectrums. The average sizes of the particles were determined by the Scherrer’s formula. The special Ms and Mössbauer spectra of BiY₂Cr _x Fe_5?x O₁₂ nanocrystals are researched at room temperature. It is seen that the special Mss of samples are initially increased with increasing Cr³⁺ content (x < 0.1), and decreased with increasing content of Cr³⁺ ions (x > 0.1).     

Effect of Ni<Superscript>2+</Superscript> substitution on crystal structure and microwave dielectric properties for MgZrNb<Subscript>2</Subscript>O<Subscript>8</Subscript> ceramics

Monoclinic structured Mg_1?xNi_xZrNb₂O₈ (0?≤?x?≤?0.12) ceramics were synthesized for the first time through traditional solid-state reaction process and pure phase were obtained in all range. Rietveld refinement was used to analyze the crystal structure. With the increase of Ni²⁺ substitution amount, ε _r decreased, Q?×?f rose first then fell, τ _f shifted for the positive direction. Bond ionicity, lattice energy and bond energy were separately calculated to investigate the correlations with microwave dielectric properties. Typically, ceramics samples with the composition of Mg_0.92Ni_0.08ZrNb₂O₈ sintered at 1280 °C for 4 h exhibited the optimum microwave dielectric properties: ε _r ?=?24.58, Q?×?f?=?74534.1 GHz, τ _f ?=???49.11 ppm/°C, which could be a promising material for application.