共查询到20条相似文献,搜索用时 15 毫秒
1.
2.
Denisenko N. I. Maslyuk V. A. Yakovenko R. V. 《Powder Metallurgy and Metal Ceramics》2019,57(11-12):740-746
Powder Metallurgy and Metal Ceramics - The abrasive wear of reinforced Kh13M2–Cr3C2 steels against a diamond wheel has been studied. The optimum composition of the reinforced chromium steels... 相似文献
4.
以冶金耐火材料电熔镁砂为研究对象,采用正交试验法,对振动磨的产品粒度分布规律和粉磨动力学进行深入系统的研究。通过回归经验公式,揭示了振动磨机粉磨效果与各主要影响因素之间的关系。 相似文献
5.
从硬件和软件两个方面介绍了模拟轧钢的具体使用方法和实现的手段。详细地给出了轧线上各处检测器状态时序的计算方法、模拟方案数据的确定,最后还给出了模拟调节程序的模拟运行方法。 相似文献
6.
磨煤机是粉煤制备系统中的核心设备,其作用是将具有一定尺寸的块煤干燥、破碎并磨制成粉煤,常用的有卧式球磨机和立式磨煤机两种。本文介绍了粉煤制备系统的工艺流程,对两种磨煤机进行了对比,详细描述了立式磨煤机的结构特点、工作原理以及在白银有色集团股份有限公司铜业公司生产中的应用情况。 相似文献
7.
8.
9.
10.
11.
Debasis Chaira S. Sangal B. K. Mishra 《Transactions of the Indian Institute of Metals》2011,64(6):549-554
Nanocrystalline TiC powder is synthesized from corresponding elemental constituents by reaction milling in a dual drive planetary
mill. The study shows nanocrystalline TiC powder could be produced from Ti + graphite and Ti + activated carbon powder after
10 h of milling. Raman spectroscopy provides evidence in support of formation of TiC after 10 h of milling. Scanning electron
microscopy reveals the size reduction and morphology of particles at different stages of milling. Transmission electron microscopy
shows the formation of nanocrystalline TiC powder with particle size in the range of 50–200 nm. The lattice parameter of TiC
(fcc) has been precisely calculated from first two strong peaks as 0.42 nm. 相似文献
12.
A powder metallurgy method is developed to recondition the worn surfaces of food and processing equipment components. A combined additive is composed to minimize the powder losses in sintering. A technique is constructed to determine the powder consumption as a function of the required metallic coating thickness. A rapid method is developed to determine the porosity of the coating. The proposed technology is used to fabricate a wear-resistant defectless metallic coating with favorable residual stresses, and the adhesive strength of this coating is equal to the strength of the base metal. 相似文献
13.
通过实施球磨系统磨内工况优化、高效转子分级机的应用以及开路循环控制系统的应用等措施,使球磨粉纯度达到稳定可调,球磨粉产量显著提高,满足了成型生产要求。 相似文献
14.
15.
16.
包钢4#、6#高炉喷煤系统主要采用2台HP1103型中速磨煤机,文章论述了包钢4#、6#高炉喷吹原煤贮运系统冬季生产存在问题及困难,分析了设备隐患对高炉喷煤量的影响,并采取了相应措施. 相似文献
17.
18.
Abstract Combustion of powder mixtures under adiabatic conditions -Self-propagating High-temperature Synthesis (SHS)-is an efficient and attractive technique to synthesize a host of materials for high technology applications, namely, ceramics, intermetallics, composites and functionally graded materials. Conditions necessary for and general features of this technique are briefly reviewed. Experimental investigations on synthesis of nickel monoaluminide from stoichiometric mixtures of component powders by this technique using plane-wave propagation mode is carried out. Effects of reaction parameters namely, bulk density of compacts, amount of inert dilutions and atmospheres on velocity of combustion wave propagation and combustion peak temperature are investigated. From the dependence of propagation velocity on combustion temperature an activation energy of 170.99 kJ/mole is obtained for SH-synthesis of NiAl. The synthesized products showed equiaxed large grained microstructures. 相似文献
19.
20.
为提前抛弃部分最终尾矿,提高入选矿石品位,降低磨矿能耗,通过实验室试验和半工业试验,证明了粉矿湿式预选技术预选尾矿铁品位仅为4.38%,铜品位0.038%,钴品位0.0103%,均低于或接近湿选尾矿品位,完全可以作为合格尾矿抛去.应用表明,球磨机处理量达到40t/h,比设湿式预选作业前提高5t/h,废石品位符合抛废要求,抛废产率为8.04%,每年可创经济效益70万元以上. 相似文献