等离子体处理对芳纶性能的影响

芳纶作为增强材料在复合材料中有广泛的应用,其界面性能是影响其复合材料界面粘结性能的重要因素。分别采用H2、空气低温等离子体对芳纶表面进行了处理。研究了等离子体表面改性后芳纶性能的变化。结果表明:经低温等离子体处理后纤维表面张力增大,由46.0mN·m-1增加到63.2mN·m-1;表面极性增强,极性分数由58.0%提高到69.9%,而纤维单丝断裂强度未有明显变化。     

介质阻挡放电等离子体处理芳纶的表面性能研究

采用介质阻挡放电(DBD)装置对芳纶1414表面进行改性处理,探讨低温等离子体处理对纤维表面性能的影响。结果表明:经过DBD等离子体处理后,芳纶1414纤维表面粗糙程度加剧,粘结性能和浸润性能有了明显的改善;当DBD等离子体处理功率为200～300 W,时间为60 s,氩气流量为2～3 L/min时,芳纶1414的界面剪切强度从处理前的11.9 MPa上升到14.2 MPa,接触角由处理前的85.0°下降到了60.6°。     

低温等离子体改性芳纶1414的研究

对芳纶1414进行低温等离子体表面改性以改善其构成复合材料时的界面黏结性能。设计正交试验,得到低温等离子体处理芳纶1414的最佳条件为放电功率100 W,处理时间300 s,放电压强20 Pa。采用电子单纤维强力机、纤维摩擦因数测定仪、纤维接触角测量仪、扫描电子显微镜和傅里叶变换红外光谱仪对改性前后的芳纶1414进行性能表征。结果表明:经过低温等离子体改性的芳纶1414的断裂强力较原样下降了6.3%,静摩擦因数上升了15.7%,表面接触角减小了36.8%,纤维表面出现微小均匀的凹槽,增大了比表面积,引入了自由基团,增大了表面反应活性,从而改善了与树脂基体复合时的黏结强度。     

芳纶纤维等离子体接枝改性处理研究

采用等离子体接枝对芳纶纤维表面进行改性处理,采用XPS、浸润性、界面剪切强度对等离子体接枝处理前后的表面组成、复合材料界面粘接性能等进行了研究,结果表明:等离子体接枝处理可以有效地提高芳纶纤维表面的极性官能团,增加与基体树脂-环氧树脂的浸润性,进而提高芳纶/环氧复合材料的界面粘接强度.     

空气等离子体处理芳纶纤维及其与天然橡胶/乳聚丁苯橡胶的黏合性能

考察了空气等离子体处理对芳纶纤维表面结构形态的影响,研究了空气等离子体和间苯二酚-甲醛-胶乳(RFL)浸胶处理芳纶纤维与天然橡胶(NR)/乳聚丁苯橡胶(ESBR)的黏合性能,并对经处理的芳纶纤维与NR/ESBR体系的界面层作了动态力学分析。结果表明,芳纶纤维经空气等离子体处理后,表面粗糙度增大,表面积增加,结晶度减小,但处理功率过大、处理时间过长时,芳纶纤维的表面又变得比较光滑、结晶度又呈增大趋势。随着等离子体处理时间的延长,芳纶纤维与NR/ESBR的黏合性能增强,但处理时间过长时,芳纶纤维与NR/ESBR的黏合性能下降;等离子体处理芳纶纤维经RFL进一步浸胶处理后,芳纶纤维与NR/ESBR的黏合性能大幅度提高。芳纶纤维与NR/ESBR的界面存在介于高模量芳纶纤维和低模量橡胶之间的过渡层。     

低温等离子体对PBO纤维表面的改性

采用硅烷偶联剂处理聚对苯撑苯并双噁唑(PBO)纤维,利用常压射频低温等离子体对PBO纤维进行了表面处理,通过扫描电镜、红外光谱、光学显微镜等研究了处理时间对PBO纤维表面官能团和表面形貌的影响规律,通过单丝拔出实验测定PBO纤维基复合材料的界面剪切强度。结果表明:经过常压射频低温等离子体处理后,PBO纤维的表面形成了大量的极性基团,表面产生明显的凹坑,PBO纤维与树脂的粘接性能提高50%,纤维的拉伸强度下降5%。     

低温氨气等离子体对芳纶表面的改性

采用氨气等离子体对芳纶表面进行改性,用X-射线光电子能谱、场发射扫描电子显微镜、力学性能测试等手段对改性前后纤维表面的元素组成、形貌及其拉伸强度进行表征,并进一步通过微脱黏方法分析了等离子体处理条件对芳纶/环氧树脂复合材料界面黏结强度的影响。结果表明:芳纶经表面改性后,其表面极性官能团、表面粗糙度均有所增加,同时与环氧树脂基体的界面黏结强度明显增加。     

芳纶纤维/AFR树脂复合材料界面粘结性能的研究

为了改善芳纶纤维复合材料的界面粘结性能,合成了一种新型树脂(AFR)作为基体,以未经任何表面处理的芳纶纤维作增强材料,制备了芳纶纤维/AFR复合材料。采用测定表面能、接触角、层间剪切强度、横向拉伸性能和扫描电镜观察形貌等方法,从宏观和微观等方面研究了芳纶纤维/AFR复合材料的界面粘结性能。结果表明,AFR树脂与芳纶纤维有相近的表面能,AFR树脂溶液与芳纶纤维的接触角为42.8°,而环氧树脂(EP)与芳纶纤维的接触角为68°,说明AFR树脂对芳纶纤维的润湿性优于EP树脂;芳纶/AFR复合材料的层间剪切强度、横向拉伸强度和纵向拉伸强度分别为74.64MPa、25.34MPa和2256MPa,比芳纶/EP复合材料的相应强度分别提高了28.7%、32.5%和13.4%,其复合材料破坏面的形貌也说明芳纶纤维与AFR树脂之间的界面粘结性能较好。     

氨气等离子体改性处理芳纶Ⅲ表面的研究

以氨气为反应气体,对芳纶Ⅲ进行等离子体表面改性处理,研究了等离子体处理时间和处理功率对纤维表面性能的影响;采用X射线光电子能谱、场发射扫描电镜、接触角和微脱粘实验等测试方法对改性前后纤维表面元素组成、形貌、润湿能力以及界面粘结强度进行表征。结果表明:芳纶Ⅲ经过氨气等离子体改性后,表面含氮极性基团的含量增加,粗糙程度增大,润湿能力得到明显的改善;当氨气等离子体处理时间为15 min,功率为100 W时,芳纶Ⅲ与环氧树脂的界面粘结强度从处理前的12.9 MPa提高到18.2 MPa,与水的接触角由处理前的71.4°下降到46.8°。     

常压等离子体改善高性能纤维粘结性的研究

以氦气为载气,氧气为反应气体,对高强度聚乙烯和Twaron 1000芳纶两种高性能纤维进行常压等离子体处理,来改善纤维的粘结性能;采用单纤维抽拔实验测定等离子体处理前后纤维与环氧树脂之间的界面剪切力;利用原子力显微镜和X射线光电子能谱仪分析等离子体处理前后纤维表面形态和化学成分的变化。结果表明:高强度聚乙烯纤维和芳纶经常压等离子体处理后,纤维表面粗糙度增加,纤维表面碳元素含量下降,羟基、羧基等含氧或氮的极性基团增加,纤维粘结性能得到提高,但其强度无明显变化。     

Interfacial studies on the surface modified aramid fiber reinforced epoxy composites

In this work, solutions of rare earth modifier (RES) and epoxy chloropropane (ECP) grafting modification method were used for the surface treatment of aramid fiber. The effect of chemical treatment on aramid fiber has been studied in a composite system. The surface characteristics of aramid fibers were characterized by Fourier transform infrared spectroscopy (FTIR). The interfacial properties of aramid/epoxy composites were investigated by means of the single fiber pull‐out tests. The mechanical properties of the aramid/epoxy composites were studied by interlaminar shear strength (ILSS). As a result, it was found that RES surface treatment is superior to ECP grafting treatment in promoting the interfacial adhesion between aramid fiber and epoxy matrix, resulting in the improved mechanical properties of the composites. Meanwhile, the tensile strengths of single fibers were almost not affected by RES treatment. This was probably due to the presence of reactive functional groups on the aramid fiber surface, leading to an increment of interfacial binding force between fibers and matrix in a composite system. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102:4165–4170, 2006     

RETRACTED ARTICLE: Surface modification of aramid fibers with novel chemical approach

Friedel–Crafts Reaction as a simple and convenient approach to the surface modification of aramid fiber was introduced in this paper. Epoxy chloropropane was chosen as the treatment reagent to modify aramid fibers surface via Graft reaction. After the modification, the interfacial properties of aramid/epoxy composites were investigated by the single fiber pull-out test (SFP), and the mechanical properties of aramid fibers were investigated by the tensile strength test. The results showed that the interfacial shear strength (IFSS) value of aramid/epoxy composites was enhanced by about 50%, and the tensile strength of aramid fibers had no obvious damage. The crystalline state of aramid fibers was determined by X-ray diffraction instrument (XRD), and the results showed that there were not any distinct crystal type varieties. The surface elements of aramid fibers were determined by X-ray photoelectron spectroscopy (XPS), the analysis of which showed that the oxygen/carbon ratio of aramid fiber surface increased obviously. The possible changes of the chemical structure of aramid fibers were investigated via Fourier transform infrared spectrum (FTIR), and the analysis of which showed that the epoxy functional groups were grafted into the molecule structure of aramid fibers. The surface morphology of aramid fibers was analyzed by Scanning electron microscope (SEM), and the SEM results showed that the physical structure of aramid fibers was not etched or damaged obviously. The surface energy of aramid fibers was investigated via the dynamic capillary method, and the results showed that the surface energy was enhanced by 31.5%, and then the wettability degree of aramid fiber surface was enhanced obviously too. All of the results indicated that this novel chemical modification approach not only can improve the interfacial bonding strength of aramid/epoxy composites remarkably, but also have no negative influence on the intrinsic tensile strength of aramid fibers.     

左旋多巴胺处理对芳纶表面结构与性能的影响

利用L-3,4-二羟基苯丙氨酸(L-DOPA)的氧化自聚合,在杂环芳纶表面修饰聚L-3,4-二羟基苯丙氨酸(PDOPA)活性涂层来提高芳纶的表面活性及耐紫外辐照性能。结果表明:改性后芳纶表面粗糙度显著提高,同时,PDOPA涂层上大量的羧基、羟基等活性单元均有利于增强与环氧树脂的机械锁合力,改性后芳纶/环氧树脂复合材料的界面剪切强度提高了32.0%。此外,上述改性过程对杂环芳纶本身力学性能影响较小,纤维的拉伸强度保持率可以达到100%,基本实现了无损改性。同时,由于PDOPA的保护作用,改性后芳纶的耐紫外辐射性能显著提高;经过168 h紫外线辐照处理后,其拉伸强度保持率可达到92.5%,显著提升了杂环芳纶的耐紫外线辐照特性。     

芳纶纤维增强树脂基复合材料的界面粘结性能研究

为了改善芳纶纤维增强树脂基复合材料的界面粘结性能,从树脂基体入手,依据相似相容原理和芳纶的结构特点,合成出新型热固性树脂(AFR–T)用作芳纶复合材料的基体,以未经表面处理的芳纶作增强材料,采用热压成型法制备了AFR–T/芳纶纤维复合材料,并通过测定溶度参数、接触角、线膨胀系数、层间剪切强度(ILSS)和横向拉伸强度等方法研究了复合材料的界面粘结性能。结果表明,AFR–T树脂浇注体与芳纶的溶度参数相近,AFR–T树脂溶液在芳纶纸表面的接触角为36.9°,小于环氧树脂(EP)溶液与芳纶纸的接触角(53.2°),说明AFR–T树脂对芳纶的浸润性优于EP;AFR–T/芳纶纤维复合材料的ILSS和横向拉伸强度为73.0 MPa和25.3 MPa,分别比EP/芳纶纤维复合材料提高了25.9%和32.5%,这表明AFR–T树脂与芳纶纤维之间的浸润性和界面粘结性能较好。     

Effects of atmospheric pressure helium/air plasma treatment on adhesion and mechanical properties of aramid fibers

In order to investigate the effect of atmospheric pressure plasmas on adhesion between aramid fibers and epoxy, aramid fibers were treated with atmospheric pressure helium/air for 15, 30 and 60 s on a capacitively-coupled device at a frequency of 5.0 kHz and He outlet pressure of 3.43 kPa. SEM analysis at 10 000× magnification showed no significant surface morphological change resulted from the plasma treatments. XPS analysis showed a decrease in carbon content and an increase in oxygen content. Deconvolution analysis of C1s, N1s and O1s peaks showed an increase in surface hydroxyl groups that can interact with epoxy resin. The microbond test showed that the plasma treatment for 60 s increased interfacial shear strength by 109% over that of the control (untreated). The atmospheric pressure plasma increased single fiber tensile strength by 16-26%.     

Surface ammonification of the mutual‐irradiated aramid fibers in 1,4‐dichlorobutane for improving interfacial properties with epoxy resin

The mutual irradiated aramid fibers in 1,4‐dichlorobutane was ammoniated by ammonia/alcohol solution, in an attempt to improve the interfacial properties between aramid fibers and epoxy matrix. Scanning electron microscopy (SEM), X‐ray photoelectron spectroscopy (XPS), dynamic contact angle analysis (DCA), interfacial shear strength (IFSS), and single fiber tensile testing were carried out to investigate the functionalization process of aramid fibers and the interfacial properties of the composites. Experimental results showed that the fiber surface elements content changed obviously as well as the roughness through the radiation and chemical reaction. The surface energy and IFSS of aramid fibers increased distinctly after the ammonification, respectively. The amino groups generated by ammonification enhanced the interfacial adhesion of composites effectively by participating in the epoxy resin curing. Moreover, benefited by the appropriate radiation, the tensile strength of aramid fibers was not affected at all. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44924.     

Influence of oxygen plasma treatment parameters on the properties of carbon fiber

This study is focused on the impact of oxygen plasma treatment on properties of carbon fibers and interfacial adhesion behavior between the carbon fibers and epoxy resin. The influences of the main parameters of plasma treatment process, including duration, power, and flow rate of oxygen gas were studied in detail using interlaminar shear strength (ILSS) of carbon fiber composites. The ILSS of composites made of carbon fibers treated by oxygen plasma for 1 min, at power of 125 W, and oxygen flow rate of 100 sccm presented a maximum increase of 28% compared to composites made of untreated carbon fibers. Furthermore, carbon fibers were characterized by scanning electron microscopy (SEM), tensile strength test, attenuated total reflectance Fourier transform infrared (ATR-FTIR), and Raman spectroscopy analyses. It was found that the concentration of reactive functional groups on the fiber surface was increased after the plasma modification, as well the surface roughness, which finally improved the interfacial adhesion between carbon fibers and epoxy resin. However, high power and long exposure times could partly damage the surface of carbon fibers and decrease the tensile strength of filaments and ILSS of treated fiber composites.     

Effect of rare earth elements surface treatment on tensile properties of aramid fiber‐reinforced epoxy composites

Solutions of rare earth modifier (RES) and epoxy chloropropane (ECP) grafting modification method were used for the surface treatment of aramid fiber. Tensile properties of both the aramid/epoxy composites and single fibers were tested. The effects of RES concentration on tensile properties of aramid/epoxy composites were investigated in detail to explore an optimum amount of rare earth elements in solution for modifying aramid fiber. The fracture surface morphologies of tensile specimens were observed and analyzed with the aid of SEM. The experimental results show that rare earth treatment is superior to ECP grafting treatment in promoting interfacial adhesion between the aramid fiber and epoxy matrix. Meanwhile, the tensile strengths of single fibers were almost not affected by RES treatment. The optimum performance is obtained when the content of rare earth elements is 0.5 wt %. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 1037–1041, 2004     

Effect of ultrasound on wettability between aramid fibers and epoxy resin

Good wetting of reinforced fiber by resin was a main factor in the improvement of the interface adhesion of their composites. Ultrasound with a frequency of 20 kHz was used to improve the wettability between aramid fibers and epoxy resin during the winding process of the composites. The effects of ultrasound on the viscosity and surface tension of epoxy resin and on the surface characteristics of aramid fibers were investigated. The wettability of aramid fibers and treated epoxy resin under different conditions and of aramid fibers and epoxy resin under ultrasonic online treatment were compared. The results indicated that the main action of ultrasound was to force epoxy resin to impregnate aramid fibers, in addition to the influence of ultrasound on the properties of epoxy resin and aramid fibers. The results of microdebond testing showed that the interfacial shear strength (IFSS) of aramid/epoxy composites could be 26% higher than that of untreated composites because of the improved wettability between aramid fibers and epoxy resin subjected to ultrasonic online treatment. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci, 2006