含氮杂环双季铵盐在高温酸性溶液中的缓蚀性能

以喹啉为母体,对二氯苄为卤化剂合成一种含氮杂环双季铵盐,并对其结构进行红外表征;同时利用静态失重法、极化曲线、电化学阻抗谱(EIS)对其在高温酸性水介质中的缓蚀性能进行了研究.极化曲线表明该双季铵盐缓蚀剂为强烈的阴极型缓蚀剂,EIS表明含N 的杂环分子在低频区表现为明显的吸脱附感抗环,表明在弱阳极极化下季铵盐类缓蚀剂就会发生阳极脱附.失重试验和电化学测试表明其缓蚀性能良好,但进一步性能的提高还需要通过复配来降低其脱附敏感性.     

氯离子与咪唑啉复配缓蚀剂的合成与应用

利用油酸和二乙烯三胺为原料合成咪唑啉季铵盐缓蚀剂后,在50℃、5%的盐酸介质中用静态失重法对咪唑啉季铵盐与阴离子表面活性剂和无机阴离子的研究,得到了一个与咪唑啉季铵盐有最佳复配效果的复配体,咪唑啉季铵盐与I-复配比为1:1(质量比)时,缓蚀剂的缓蚀效果最佳.在不同时间和不同温度下对复合型缓蚀剂的缓蚀效率进行了研究.结果表明,新型缓蚀剂对A3钢的缓蚀率达到99%以上,与单独用咪唑啉季铵盐相比,其缓蚀效率提高了0.7%左右.     

氯化钠对铝硅矿物浮选的影响及其作用机理

采用季铵盐DTAL作捕收剂,研究了氯化钠对一水硬铝石和叶蜡石浮选的影响及其作用机理.随着氯化钠浓度的增加,叶蜡石的浮选回收率显著提高,而一水硬铝石的可浮性受其影响很小.机理研究表明:氯化钠对一水硬铝石的zeta-电位没有影响,而能显著降低叶蜡石的zeta-电位,增强捕收剂与叶腊石的静电作用,促进捕收剂的吸附而活化其浮选;叶蜡石表面电位的降低是因为氯离子对叶蜡石存在选择性吸附作用并对其结构进行插层,使得叶蜡石的层间距从0.93 nm增大至1.40 nm.溶液化学计算表明:氯化钠改变溶液的离子强度,显著降低了季铵盐阳离子表面活性剂的临界胶束浓度,使得吸附了捕收剂的矿物表面更容易疏水上浮.     

一种复合型咪唑啉缓蚀剂

以油酸和二乙烯三胺为原料合成咪唑啉季铵盐缓蚀剂后,在50℃、5%的盐酸溶液中用静态失重法对咪唑啉季铵盐与阴离子表面活性剂和无机阴离子进行研究,得到了一个与咪唑啉季铵盐有最佳复配效果的复配体,咪唑啉季铵盐与I-复配比为1∶1(质量比)时,缓蚀剂的缓蚀效果最佳。在不同时间和不同温度下对复合型缓蚀剂的缓蚀效率进行了测量。这种缓蚀剂对A3钢的缓蚀率达到99%以上,比单独用咪唑啉季铵盐缓蚀效率提高了0.7%。     

缓蚀剂分子结构与抗硫性能及其缓蚀机理研究

用饱和H₂S/CO₂失重法、高压H₂S/CO₂动态失重法、原子力显微镜（AFM）、环境扫描电镜（SEM）和X射线能量色散光谱（EDX）研究了咪唑啉衍生物、曼尼希碱、吡啶季铵盐、喹啉季铵盐和新稠杂环季铵盐5种不同分子结构缓蚀剂对N80钢的抗硫性能。结果表明5种缓蚀剂对N80钢的抗硫性能均随缓蚀剂浓度的增加而增强,各缓蚀剂的抗硫性能优劣顺序为：新稠杂环季铵盐>喹啉季铵盐>吡啶季铵盐>咪唑啉衍生物>曼尼希碱。静电吸附作用较强、空间位阻效应较小且中心吸附原子的电子云密度较大的缓蚀剂抗硫效果更好,其缓蚀机理主要是有效抑制CO₂/Cl^-腐蚀且促使试片表面生成致密的硫化物保护膜。     

席夫碱基季铵盐型双子表面活性剂对碱性锌电极电化学性能的影响

目的选择席夫碱基季铵盐型双子表面活性剂作为电解液添加剂,改善碱性锌电极的电化学性能,提高其耐蚀性能。方法通过电化学分析法,如失重法、塔菲尔极化曲线法、交流阻抗法等分析研究三种席夫碱基季铵盐型双子表面活性剂(D1、D2、D3)对锌电极电化学性能的影响,利用X射线光电子能谱(XPS)和扫描电子显微镜(SEM)研究在6 mol/L KOH电解液(饱和ZnO)浸泡48 h后,锌片表面的成分和形貌。结果室温下,缓蚀率随席夫碱基季铵盐型表面活性剂浓度升高而增加,当浓度进一步增大,缓蚀率变化不大。三种席夫碱基表面活性剂中,D3缓蚀能力最强,缓蚀率最高达95.67%,抑制腐蚀的效果顺序为:D3D2D1,属于抑制阳极型缓蚀剂。结论 D1、D2、D3作为碱性锌电极的电解液添加剂,可以有效减缓锌电极的腐蚀、变形、钝化及枝晶形成的能力,改善了碱性锌电极的电化学性能,D1、D2、D3适合作为碱性锌电池的缓蚀添加剂。     

溶剂热合成γ-AlOOH

用Al2(SO4)3、尿素和一种新型咪唑啉型表面活性剂-二(2-十一烷基-1-甲酰胺乙基咪唑啉)己二胺季铵盐(SUAEIHDI)为原料,以H2O/DMF、H2O/乙醇为分散介质,在150、190 ℃条件下,溶剂热合成了γ-AlOOH.主要讨论了溶剂和表面活性剂的协同作用、表面活性剂加入量、溶剂种类、反应温度对粒子大小和形貌的影响.     

硫酸介质中Gemini表面活性剂对碳钢的吸附缓蚀性能

通过失重法和极化曲线法研究了阳离子季铵盐型Gemini表面活性剂Π-14-3及其添加卤离子的复配体系对A3钢在硫酸溶液中的缓蚀性能及其机理.结果表明,表面活性剂分子Π-14-3对A3钢在0.5 mol/L的硫酸中具有很好的缓蚀性能;在缓蚀剂浓度很低时,通过加入一定量的卤离子,可以得到较高的缓蚀性能,从而降低其应用成本;在硫酸介质中,Gemini表面活性剂在金属表面的吸附符合Langmuir吸附机理.     

含杂原子的双子表面活性剂的合成与应用

以N,N-二甲基十二烷基胺和3-氧杂-1,5-二溴戊烷为原料合成了以3-氧杂戊基为联接基团的季铵盐型双子表面活性剂。产物的结构用红外光谱和核磁共振氢谱进行表征。测定了25℃下双季铵盐水溶液及其与NP-6、NP-8、NP-15、AEO-3的二元复配体系的表面张力。结果表明,与传统单链表面活性剂相比,双季铵盐表面活性剂具有更为优异的表面活性;每一种二元复配体系都具有显著降低表面张力的协同增效作用。与传统杀菌剂1631(十六烷基三甲基溴化铵)相比,双季铵盐表面活性剂具有更为优异的杀菌抑菌性能,其中对苹果轮纹菌、小麦赤霉菌的杀菌抑菌作用最佳。考察了弱碱性介质中双季铵盐水溶液及其复配体系对锌的缓蚀作用,结果表明:当pH值为8,双季铵盐水溶液的浓度低于20 mg/L时对锌具有较好的缓蚀作用,而高于此浓度时的缓蚀效果明显下降并表现出一定的腐蚀作用;在复配体系中,双季铵盐与NP-15的1∶1二元复配体系对锌的缓蚀作用最好。     

季铵盐双子表面活性剂的缓蚀性能研究

采用自制的季铵盐双子表面活性剂1,6-二(癸烷基吗啉)己烷(HDMB)作为缓蚀剂,用失重及极化曲线研究了该表面活性剂在1 mol/L盐酸溶液中对Q235钢的缓蚀效果.失重结果表明:在1 mol/L盐酸溶液中HDMB对Q235钢具有良好的缓蚀作用,缓蚀率随缓蚀剂浓度的增加而增大,当浓度达到0.1 mmol/L时,缓蚀率趋于稳定.通过吸附理论、动力学和热力学公式得到相应的参数,并讨论了缓蚀作用机理;极化曲线法表明:HDMB为混合抑制型缓蚀剂.     

Effects of Post-weld Heat Treatment on Microstructure,Mechanical Properties and the Role of Weld Reinforcement in 2219 Aluminum Alloy TIG-Welded Joints

In as-welded state, each region of 2219 aluminum alloy TIG-welded joint shows diff erent microstructure and microhardness due to the diff erent welding heat cycles and the resulting evolution of second phases. After the post-weld heat treatment, both the amount and the size of the eutectic structure or θ phases decreased. Correspondingly, both the Cu content in α-Al matrix and the microhardness increased to a similar level in each region of the joint, and the tensile strength of the entire joint was greatly improved. Post-weld heat treatment played the role of solid solution strengthening and aging strengthening. After the post-weld heat treatment, the weld performance became similar to other regions, but weld reinforcements lost their reinforcing eff ect on the weld and their existence was more of an adverse eff ect. The joint without weld reinforcements after the post-weld heat treatment had the optimal tensile properties, and the specimens randomly crack in the weld zone.     

The First Phase of the SRIF Industrialized Base in ＂West Area＂ Has Been Put into Operation

After nearly two years＇ tense construction, the first phase of industrialized base of Shenyang Research Institute of Foundry （SRIF）, located at the Tiexi Casting and Forging Industrial Park in the west of Tiexi District, has now been completed and formally put into operation.     

Thermodynamics Study on the Decomposition of Chromite with KOH

Institute of Process Engineering, Chinese Academy of Sciences, China, has proposed a method for oxidative leaching of chromite with potassium hydroxide. Understanding the mechanism of chromite decomposition, especially in the potassium hydroxide fusion, is important for the optimization of the operating parameters of the oxidative leaching process. A traditional thermodynamic method is proposed and the thermal decomposition and the reaction decomposition during the oxidative leaching of chromite with KOH and oxygen is discussed, which suggests that chromite is mainly destroyed by reactions with KOH and oxygen. Meanwhile, equilibrium of the main reactions of the above process was calculated at different temperatures and oxygen partial pressures. The stable zones of productions, namely, K2CrO4 and Fe2O3, increase with the decrease of temperature, which indicates that higher temperature is not beneficial to thermodynamic reactions. In addition, a comparison of the general alkali methods is carried out, and it is concluded that the KOH leaching process is thermodynamically superior to the conventional chromate production process.     

Influence of Heat Treatment on Damping Behaviour of the Magnesium Wrought Alloy AZ61

The effect of isochronal heat treatments for 1h on variation of damping, hardness and microstructural change of the magnesium wrought alloy AZ61 was investigated. Damping and hardness behaviour could be attributed to the evolution of precipitation process. The influence of precipitation on damping behaviour was explained in the framework of the dislocation string model of Granato and Lücke.     

Effect of Rare Earth Doping on Impedance,Modulus and Conductivity Properties of Multiferroic Composites:0.5(BiLa_xFe_(1-x)O_3)–0.5(PbTiO_3)

The Lanthanum-doped bismuth ferrite–lead titanate compositions of 0.5(Bi LaxFe1-xO3)–0.5(Pb Ti O3)(x = 0.05,0.10,0.15,0.20)(BLxF1-x-PT) were prepared by mixed oxide method.Structural characterization was performed by X-ray diffraction and shows a tetragonal structure at room temperature.The lattice parameter c/a ratio decreases with increasing of La(x = 0.05–0.20) concentration of the composites.The effect of charge carrier/ion hopping mechanism,conductivity,relaxation process and impedance parameters was studied using an impedance analyzer in a wide frequency range(102–106Hz) at different temperatures.The nature of Nyquist plot confirms the presence of bulk effects only,and non-Debye type of relaxation processes occurs in the composites.The electrical modulus exhibits an important role of the hopping mechanism in the electrical transport process of the materials.The ac conductivity and dc conductivity of the materials were studied,and the activation energy found to be 0.81,0.77,0.76 and 0.74 e V for all compositions of x = 0.05–0.20 at different temperatures(200–300 °C).     

Quantitative Analysis of the Crystallographic Orientation Relationship Between the Martensite and Austenite in Quenching–Partitioning–Tempering Steels

The orientation relationships(ORs)between the martensite and the retained austenite in low-and medium-carbon steels after quenching–partitioning–tempering process were studied in this work.The ORs in the studied steels are identified by selected-area electron diffraction(SAED)as either K–S or N–W ORs.Meanwhile,the ORs were also studied based on numerical fitting of electron backscatter diffraction data method suggested by Miyamoto.The simulated K–S and N–W ORs in the low-index directions generally do not well coincide with the experimental pole figure,which may be attributed to both the orientation spread from the ideal variant orientations and high symmetry of the low-index directions.However,the simulated results coincide well with experimental pole figures in the high-index directions{123}_(bcc).A modified method with simplicity based on Miyamoto’s work was proposed.The results indicate that the ORs determined by modified method are similar to those determined by Miyamoto’method,that is,the OR is near K–S OR for the low-carbon Q–P–T steel,and with the increase of carbon content,the OR is closer to N–W OR in medium-carbon Q–P–T steel.     

Using Finite Element and Contour Method to Evaluate Residual Stress in Thick Ti-6Al-4V Alloy Welded by Electron Beam Welding

This work was to reveal the residual stress profile in electron beam welded Ti-6Al-4V alloy plates(50 mm thick) by using finite element and contour measurement methods.A three-dimensional finite element model of 50-mmthick titanium component was proposed,in which a column–cone combined heat source model was used to simulate the temperature field and a thermo-elastic–plastic model to analyze residual stress in a weld joint based on ABAQUS software.Considering the uncertainty of welding simulation,the computation was calibrated by experimental data of contour measurement method.Both test and simulated results show that residual stresses on the surface and inside the weld zone are significantly different and present a narrow and large gradient feature in the weld joint.The peak tensile stress exceeds the yield strength of base materials inside weld,which are distinctly different from residual stress of the thin Ti-6Al-4V alloy plates presented in references before.     

Microstructures and Tensile Properties of Ultrafine-Grained Ni–(1–3.5) wt% SiC_(NP) Composites Prepared by a Powder Metallurgy Route

Silicon carbide nanoparticle-reinforced nickel-based composites(Ni–Si CNP),with a Si CNPcontent ranged from1 to 3.5 wt%,were prepared using mechanical alloying and spark plasma sintering.In addition,unreinforced pure nickel samples were also prepared for comparative purposes.To characterize the microstructural properties of both the unreinforced pure nickel and the Ni–Si CNPcomposites transmission electron microscopy(TEM) was used,while their mechanical behavior was investigated using the Vickers pyramid method for hardness measurements and a universal tensile testing machine for tensile tests.TEM results showed an array of dislocation lines decorated in the sintered pure nickel sample,whereas,for the Ni–Si CNPcomposites,the presence of nano-dispersed Si CNPand twinning crystals was observed.These homogeneously distributed Si CNPwere found located either within the matrix,between twins or on grain boundaries.For the Ni–Si CNPcomposites,coerced coarsening of the Si CNPassembly occurred with increasing Si CNPcontent.Furthermore,the grain sizes of the Ni–Si CNPcomposites were much finer than that of the unreinforced pure nickel,which was considered to be due to the composite ball milling process.In all cases,the Ni–Si CNPcomposites showed higher strengths and hardness values than the unreinforced pure nickel,likely due to a combination of dispersion strengthening(Orowan effects) and particle strengthening(Hall–Petch effects).For the Ni–Si CNPcomposites,the strength increased initially and then decreased as a function of Si CNPcontent,whereas their elongation percentages decreased linearly.Compared to all materials tested,the Ni–Si CNPcomposite containing 1.5% Si C was found more superior considering both their strength and plastic properties.     

Directional Growth of Tin Crystals Controlled by Combined Solute Concentration Gradient Field and Static Magnetic Field

A new method was introduced to achieve directional growth of Sn crystals. Microstructures in liquid(Pb)/liquid(Sn) diffusion couples were investigated under various static magnetic fields. Results show that the β-Sn crystals mainly reveal an irregular dendritic morphology without or with a relatively low static magnetic field(B0.3 T). When the magnetic field is increased to 0.5 T, the β-Sn dendrites close to the final stage of growth begin to show some directional character. With a further increase in the magnetic field to a higher level(0.8–5 T), the β-Sn dendrites have an enhanced directional growth character, but the dendrites show a certain deflection. As the magnetic field is increased to 12 T, the directional growth of the β-Sn dendrites in the center of the couple is severely destroyed. The mechanism of the directional growth of the β-Sn crystals and the deflection of the β-Sn crystals with the application of static magnetic field was tentatively discussed.     

电化学噪声数据处理方法概述

综述了常见的电化学噪声数据处理方法,介绍了直流趋势剔除、统计分析、快速傅立叶变换(FFT)法计算功率谱密度(PSD)以及小波变换处理电化学噪声信号的基本过程,并阐释了各种数学处理及所得参数的物理意义。