Preparation of a Highly Conductive Al2O3/TiN Interlayer Nanocomposite through Selective Matrix Grain Growth

An electroconductive TiN/Al₂O₃ nanocomposite was prepared by a selective matrix grain growth method, using a powder mixture of submicrosized α-Al₂O₃, nanosized γ-Al₂O₃, and TiN nanoparticles synthesized through an in situ nitridation process. During sintering, a self-concentration of TiN nanoparticles at the matrix grain boundary occurred, as a result of the selective growth of large α-Al₂O₃ matrix grains. Under suitable sintering conditions, a typical interlayer nanostructure with a continuous nanosized TiN interlayer was formed along the Al₂O₃ matrix grain boundary, and the electroconducting behavior of the material was significantly improved. Twelve volume percent TiN/Al₂O₃ nanocomposite with such an interlayer nanostructure showed an unprecedentedly low resistivity of 8 × 10⁻³Ω·cm, which was more than two orders lower than the TiN/Al₂O₃ nanocomposite without such an interlayer nanostructure.     

Conversion from β-Ce2O3·11Al2O3 to α-Al2O3 in Tetragonal ZrO2 Matrix

Composites of β-Ce₂O₃·11Al₂O₃ and tetragonal ZrO₂ were fabricated by a reductive atmosphere sintering of mixed powders of CeO₂, ZrO₂ (2 mol% Y₂O₃), and Al₂O₃. The composites had microstructures composed of elongated grains of β-Ce₂O₃·11Al₂O₃ in a Y-TZP matrix. The β-Ce₂O₃·11Al₂O₃ decomposed to α-Al₂O₃ and CeO₂ by annealing at 1500°C for 1 h in oxygen. The elongated single grain of β-Ce₂O₃·11Al₂O₃ divided into several grains of α-Al₂O₃ and ZrO₂ doped with Y₂O₃ and CeO₂. High-temperature bending strength of the oxygen-annealed α-Al₂O₃ composite was comparable to the β-Ce₂O₃·11Al₂O₃ composite before annealing.     

Microstructural Analysis of Sintered High-Conductivity Zirconia with Al203 Additions

Transmission electron microscopy (at 100 and 1000 kV potential) and analytical scanning transmission electron microscopy were used to study α-Al₂0₃ second-phase particles and their interactions with grain boundaries in two high-conductivity Y₂0₃/Yb₂0₃ stabilized zirconia ceramics containing deliberate additions of the alumina as a sintering aid. Most of the Al₂0₃ particles were intragranular and microanalysis showed that they contained inclusions rich in Zr or Si plus Zr. Al₂O₃ particles at grain boundaries were frequently associated with amorphous cusp areas rich in Si and Al. The results suggest that the Al₂0₃ acts as a scavenger for SiO₂, removing it from grain-boundary localities. A model is proposed whereby this process occurs as the boundaries meet the second-phase particles, assisted by rapid grain-boundary diffusion. Such an ZrO₂-Al₂O₃-SiO₂ interaction and partitioning is predicted thermodynamically and offers a possible explanation for the improvements in ionic conductivity brought about by Al₂O₃ additions, as reported in the literature.     

Spark-Plasma Sintering of Silicon Carbide Whiskers (SiCw) Reinforced Nanocrystalline Alumina

The combined effect of rapid sintering by spark-plasma-sintering (SPS) technique and mechanical milling of γ-Al₂O₃ nanopowder via high-energy ball milling (HEBM) on the microstructural development and mechanical properties of nanocrystalline alumina matrix composites toughened by 20 vol% silicon carbide whiskers was investigated. SiC_w/γ-Al₂O₃ nanopowders processed by HEBM can be successfully consolidated to full density by SPS at a temperature as low as 1125°C and still retain a near-nanocrystalline matrix grain size (∼118 nm). However, to densify the same nanopowder mixture to full density without the benefit of HEBM procedure, the required temperature for sintering was higher than 1200°C, where one encountered excessive grain growth. X-ray diffraction (XRD) and scanning electron microscopy (SEM) results indicated that HEBM did not lead to the transformation of γ-Al₂O₃ to α-Al₂O₃ of the starting powder but rather induced possible residual stress that enhances the densification at lower temperatures. The SiC_w/HEBMγ-Al₂O₃ nanocomposite with grain size of 118 nm has attractive mechanical properties, i.e., Vickers hardness of 26.1 GPa and fracture toughness of 6.2 MPa·m^1/2.     

Growth of Tabular α-Al2O3 Grains on Porous Alumina Substrate

Gradient, porous alumina ceramics were prepared with the characteristics of microsized tabular α-Al₂O₃ grains grown on a surface with a fine interlocking feature. The samples were formed by spin-coating diphasic aluminosilicate sol on porous alumina substrates. The sol consisted of nano-sized pseudo-boehmite (AlOOH) and hydrolyzed tetraethyl orthosilicate [Si(OC₂H₅)₄]. After drying and sintering at 1150°–1450°C, the crystallographic and chemical properties of the porous structures were investigated by analytical electron microscopy. The results show that the formation of tabular α-Al₂O₃ grains is controlled by the dissolution of fine Al₂O₃ in the diphasic material at the interface. The nucleation and growth of tabular α-Al₂O₃ grains proceeds heterogeneously at the Al₂O₃/glass interface by ripening nano-sized Al₂O₃ particles.     

Kinetics and Microstructural Evolution of Heterogeneous Transformation of θ-Alumina to α-Alumina

Ultrafine (<0.1 μm) high-purity θ-Al₂O₃ powder containing 3–17.5 mol%α-Al₂O₃ seeds was used to investigate the kinetics and microstructural evolution of the θ-Al₂O₃ to α-Al₂O₃ transformation. The transformation and densification of the powder that occurred in sequence from 960° to 1100°C were characterized by quantitative X-ray diffractometry, dilatometry, mercury intrusion porosimetry, and transmission and scanning electron microscopy. The relative bulk density and the fraction of α phase increased with annealing temperature and holding time, but the crystal size of the α phase remained ∼50 nm in all cases at the transformation stage (≤1020°C). The activation energy and the time exponent of the θ to α transformation were 650 ± 50 kJ/mol and 1.5, respectively. The results implied the transformation occurred at the interface via structure rearrangement caused by the diffusion of oxygen ions in the Al₂O₃ lattice. A completely transformed α matrix of uniform porosity was the result of appropriate annealing processes (1020°C for 10 h) that considerably enhanced densification and reduced grain growth in the sintering stage. The Al₂O₃ sample sintered at 1490°C for 1 h had a density of 99.4% of the theoretical density and average grain size of 1.67 μm.     

Effect of MgO Solute on Microstructure Development in Al2O3

The effect of MgO as a solid-solution additive in the sintering of Al₂O₃ was studied. The separate effects of the additive on densification and grain growth were assessed. Magnesia was found to increase the densification rate during sintering by a factor of 3 through a raising of the diffusion rate. The grain-size dependence of the densification rate indicated control primarily by grain-boundary diffusion. Magnesia also increased the grain growth rate during sintering by a factor of 2.5. The dependence of the grain growth rate on density and grain size suggested a mechanism of surface-diffusion-controlled pore drag. It was argued, therefore, that MgO enhanced grain growth by raising the surface diffusion coefficient. The effect of MgO on the densification rate/grain growth rate ratio was, therefore, found to be minimal and, consequently, MgO did not have a significant effect on the grain size/density trajectory during sintering. The role of MgO in the sintering of alumina was attributed mainly to its ability to lower the grain-boundary mobility.     

Microwave Plasma Synthesis of Nanostructured γ-Al2O3 Powders

Nanostructured Al₂O₃ powders have been synthesized by combustion of aluminum powder in a microwave oxygen plasma, and characterized by X-ray diffraction and electron microscopy. The main phase is γ-Al₂O₃, with a small amount of δ-Al₂O₃. The particles are truncated octahedral in shape, with mean particle sizes of 21–24 nm. The effect of reaction chamber pressure on the phase composition and the particle size was studied. The γ-alumina content increases and the mean particle size decreases with decreasing pressure. No α-Al₂O₃ appears in the final particles. Electron microscopy studies find that a particle may contain more than one phase.     

Influence of Cr and Fe on Formation of α-Al2O3 from γ-Al2O3

The effect of Cr and Fe in solid solution in γ-Al₂O₃ on its rate of conversion to α-Al₂O₃ at 1100°C was studied by X-ray diffraction. The δ form of Al₂O₃ was the principal intermediate phase produced from both pure γ-Al₂O₃ and that containing Fe³⁺ in solid solution, although addition of Fe greatly reduced crystallinity. Reflectance spectra and magnetic susceptibilities showed that Cr exists as Cr⁶⁺ in γ-Al₂O₃ and as Cr³⁺ in α-Al₂O₃, with θ-Al₂O₃ as the intermediate phase. The intermediates formed rapidly, and the rates of their conversion to α-Al₂O₃ were increased by 2 and 5 wt% additions of Fe and decreased by 2 and 4 wt% additions of Cr. An approximately linear relation observed between α-Al₂O₃ formation and decrease in specific surface area was only slightly affected by the added ions. This relation can be explained by a mechanism in which the sintering of δ- or θ-Al₂O₃, within the aggregates of their crystallites, is closely coupled with conversion of cubic to hexagonal close packing of O^2- ions by synchro-shear.     

Fabrication of Nano-Scaled α-Al2O3 Crystallites Through Heterogeneous Precipitation of Boehmite in a Well-Dispersed θ-Al2O3-Suspension

The possibility of eliminating finger or vermicular growth of α-Al₂O₃ particles obtained by calcination of boehmite was examined. Heterogeneous precipitation of boehmite in a well-dispersed θ-Al₂O₃ suspension was first prepared, in which the mass ratio of boehmite to θ-crystallite was evaluated to form agglomerates of similar sizes that will form α-Al₂O₃ crystallites of <100 nm in diameter. θ- to α-phase transformation of alumina experiences a nucleation and growth mechanism, with the critical size of nucleation being ∼25 nm for θ-Al₂O₃ and the size for accomplishment of transformation followed by finger growth being ∼100 nm. Hence, fabricating agglomerates that would form α-Al₂O₃ crystallites with sizes <100 nm accompanied with appropriate thermal treatments can be a method for obtaining α-Al₂O₃ crystallites free of finger growth. It is found that proper preparation of the agglomerate with appropriate size may initiate a simultaneous and lower temperature θ- to α-Al₂O₃ phase transformation for such powder systems, substantially limiting the mass transfer among the newly formed α-Al₂O₃ particles. Moreover, α-Al₂O₃ crystallites free of finger growth can be obtained.     

Size Control of α-Al2O3 Platelets Synthesized in Molten Na2SO4 Flux

α-Al₂O₃ platelet powders were synthesized in molten Na₂SO₄ flux. The size of α-Al₂O₃ platelets was significantly reduced when partially decomposed rather than pure Al₂(SO₄)₃ was used as the source of Al₂O₃; a further reduction in the platelet size was realized through additional seeding with nanosized α-Al₂O₃ seeds. The addition of microsized α-Al₂O₃ platelet seeds significantly influenced the platelet morphology of the final powder, as well. The platelet size of the final powder was in direct proportion to the size of the platelet seeds, and was in reverse proportion to the cube root of the platelet seed content.     

Lowering Crystallization Temperatures by Seeding in Structurally Diphasic Al2O3-MgO Xerogels

Thermal reactions in 93% Al₂O₃-7% MgO and 95.8% Al₂O₃-4.2% MgO gels seeded with α-Al₂O₃, MgAl₂O₄, α-Fe₂O₃, and SiO₂, sols were investigated by differential thermal analysis to determine the extent of nucleation catalysis of solid-state reactions. Seeding with α-Al₂O₃ lowered the α-Al₂O₃ crystallization temperature in these xerogels by 100° to 150°C. Spinel seeds have much less effect on the γ-α transition, and α-Fe₂O₃ and SiO₂ seeds do not affect it significantly. Isostructural seeding of gels may therefore permit lower ceramic processing temperatures.     

Preparation and Properties of Porous α-Al2O3 Membrane Supports

Strong and permeable macro-porous α-Al₂O₃ membrane supports are made by colloidal filtration of 20 vol% dispersions of α-Al₂O₃ with an average particle size of 600 nm. Intact compacts with very good surface quality were obtained at an optimum pH of 9.5 and dosage of 0.2 wt% ammonium aurintricarboxylate (Aluminon), based on dry alumina. The colloidal stability of the aluminon-stabilized slurries is confirmed by ξ potential measurements. Slight sintering of dense-packed α-Al₂O₃ compacts was found to result in >67% packing density and a bimodal pore-size distribution as derived from shrinkage behavior and gas adsorption studies. Non-stationary single gas permeation measurements showed improved gas permeability, compared with α-Al₂O₃ compacts prepared using powder with a smaller particle size (300 nm). The strength of the disk-shaped alumina compacts within the porosity range of 30%–20% increased from 100 to 300 MPa with a standard deviation of 20 and 50 MPa, respectively.     

Growth of α-Al2O3 Crystals by Na2O Evaporation

A technique for growing α-Al₂O₃ crystals is described in which Na₂O·11Al₂O₃ is dissolved in a liquid of composition Na₂O·4TiO₂·3Al₂O₃. Alpha Al₂O₃ is precipitated as Na₂O evaporates from the system; Na₂O·11Al₂O₃ serves as a source of Al₂O₃, and Na₂O in the liquid. The content of solids in the mixture is always such that it does not melt completely. The size of the α-Al₂O₃ crystals grown is related to the Na₂O content of the composition. Crystals as large as 4000 by 3000 μm in the α-axis direction and 500 μm in the c -axis direction have been grown.     

Sintering Kinetics at Constant Rates of Heating: Effect of Al2O3 on the Initial Sintering Stage of Fine Zirconia Powder

The sinterabilities of fine zirconia powders including 5 mass% Y₂O₃ were investigated, with emphasis on the effect of Al₂O₃ at the initial sintering stage. The shrinkage of powder compact was measured under constant rates of heating (CRH). The powder compact including a small amount of Al₂O₃ increased the densification rate with elevating temperature. The activation energies at the initial stage of sintering were determined by analyzing the densification curves. The activation energy of powder compact including Al₂O₃ was lower than that of a powder compact without Al₂O₃. The diffusion mechanisms at the initial sintering stage were determined using the new analytical equation applied for CRH techniques. This analysis exhibited that Al₂O₃ included in a powder compact changed the diffusion mechanism from grain boundary to volume diffusions (VD). Therefore, it is concluded that the effect of Al₂O₃ enhanced the densification rate because of decrease in the activation energy of VD at the initial sintering stage.     

Effect of Yttrium and Lanthanum on the Final-Stage Sintering Behavior of Ultrahigh-Purity Alumina

Final-stage sintering has been investigated in ultrahigh-purity Al₂O₃ and Al₂O₃that has been doped individually with 1000 ppm of yttrium and 1000 ppm of lanthanum. In the undoped and doped materials, the dominant densification mechanism is consistent with grain-boundary diffusion. Doping with yttrium and lanthanum decreases the densification rate by a factor of ˜11 and 21, respectively. It is postulated that these large rare-earth cations, which segregate strongly to the grain boundaries in Al₂O₃, block the diffusion of ions along grain boundaries, leading to reduced grain-boundary diffusivity and decreased densification rate. In addition, doping with yttrium and lanthanum decreases grain growth during sintering. In the undoped Al₂O₃, surface-diffusion-controlled pore drag governs grain growth; in the doped materials, no grain-growth mechanism could be unambiguously identified. Overall, yttrium and lanthanum decreases the coarsening rate, relative to the densification rate, and, hence, shifted the grain-size-density trajectory to higher density for a given grain size. It is believed that the effect of the additives is linked strongly to their segregation to the Al₂O₃grain boundaries.     

Effect of Monovalent Cation Additives on the γ-Al2O3-to-α-Al2O3 Phase Transition

The effect of monovalent cation addition on the γ-Al₂O₃-to-α-Al₂O₃ phase transition was investigated by differential thermal analysis, powder X-ray diffractometry, and specific-surface-area measurements. The cations Li⁺, Na⁺, Ag⁺, K⁺, Rb⁺, and Cs⁺ were added by an impregnation method, using the appropriate nitrate solution. β-Al₂O₃ was the crystalline aluminate phase that formed by reaction between these additives and Al₂O₃ in the vicinity of the γ-to-α-Al₂O₃ transition temperature, with the exception of Li⁺. The transition temperature increased as the ionic radii of the additive increased. The change in specific surface area of these samples after heat treatment showed a trend similar to that of the phase-transition temperature. Thus, Cs⁺ was concluded to be the most effective of the present monovalent additives for enhancing the thermal stability of γ-Al₂O₃. Because the order of the phase-transition temperature coincided with that of the formation temperature of β-Al₂O₃ in these samples, suppression of ionic diffusion in γ-Al₂O₃ by the amorphous phase containing the added cations must have played an important role in retarding the transition to α-Al₂O₃. Larger cations suppressed the diffusion reaction more effectively.     

Grain Growth in Two-Phase Ceramics: Al2O3 Inclusions in ZrO

The effect of Al₂O₃ inclusions with a greater average size (0.6 μm) than the average particle size of the major phase powder (<0.1 μm) on grain gowth was examined by sintering ZrO₂/Al₂O₃ composites (0,3,5,10, and 20 vol%) at 1400°C and then heat-treating at temperatures up to 1700°C. Normal grain growth was observed for all conditions. The inclusions appeared to have no effect on grain growth until the ZrO₂ grain size was ∼1.5 times the average inclusion size. Grain growth inhibition increased with volume fraction of the Al₂O₃ inclusion phase. At temperatures 1600°C, the inclusions were relatively immobile and most were located within the ZrO₂ grains for volume fractions <0.20; at higher temperatures, the inclusions could move with the grain boundary to coalesce. Grain growth was less inhilited when the inclusions could move with the boundaries, resulting in a larger increase in grain size than observed at lower temperatures. Analogies between mobile voids, entrapped within grain at lower temperature due to abnormal grain growth during the last state of sintering, and the observations concerning the mobile inclusions are made suggesting that grain-boundary movement can "sweep" voids to grain boundaries and eventually of four-grain junctions, where they are more likely to disappear by mass transport.     

Initial Sintering of α-Cr2O3

Since the difference between oxygen-ion and cation diffusion coefficients is greater for α-Cr₂O₃ than for α-Fe₂O₃ or α-Al₂O₃, a study of initial-sintering kinetics was undertaken to show unequivocally which species is rate controlling. Fine powders of α-Cr₂O₃, obtained by thermal decomposition of reagent-grade (NH₄)₂Cr₂O₇, were lightly compacted and their isothermal rates of shrinkage were determined between 1050° and 1300°C. Resultant data follow volume-diffusion sintering models, and calculated diffusion coefficients agree with, those measured for oxygen ions in α-Cr₂O₃. There is little evidence that oxygen diffusion along grain boundaries becomes so enhanced that chromium ions are left in control of the process.     

High-Pressure Sintering of Nanocrystalline γAl2O3

High-pressure sintering of nanocrystalline γ-A1₂O₃ has been studied over a temperature range of 923-1323 K and at a pressure of 1 GPa. The γ-Al₂O₃ to α-Al₂O₃ transformation temperature changed from 1473 K without pressure to ∼1023 K at 1 GPa. Full density was obtained at 1273 and 1323 K in 10 min. The microhardness value of fully dense α-alumina with a grain size of 142 nm was found to be 25.3 ± 0.8 GPa. The Hall-Petch slope for the very fine grain size range is different from that of the coarse-grained alumina.