基于图像法喷动床内空隙率研究

利用图像二值化方法处理图片,并采用Matlab编程实现空隙率的测量,从微观层次分析空隙率对喷动流化床内流动状态的影响。研究了颗粒粒径、喷口数量和表观气速对空隙率分布的影响。结果表明,增大表观气速使床层底部的稀相区增大,床层膨胀高度增加,空隙率也随之增加。增大颗粒粒径会增大最小临界流化速率,所以在其达到流化状态后流化床内颗粒粒径增大,床内喷动区空隙率减小比较明显。在相同条件下,与单喷口相比双喷口在床层底部附近存在合并射流,同时颗粒能到达的高度显著增加,底部两侧停滞区面积减小。结合对空隙率的分析,提出一种新的表征流化床内流化状态的参数(流化指数),可以直观地表示流化床内颗粒的流化状态。     

导向管喷动床内单相流场及声波对流场影响的数值模拟

为阐明超细粉在声场导向管喷动流化床内的流化机理,并为进一步优化和完善床层结构及操作条件提供基础,采用标准k-ε湍流模型计算了导向管喷动流化床内的单相气体流场,考察了进口流化气速和射流气速对气体流动规律的影响,以及声场对导向管喷动流化床内气体轴向速度分布及其脉动均方根的影响。结果表明:在高速射流条件下,导向管喷动流化床内气体呈内循环流动,气体循环流量随流化气速度的增加而减小,但随射流气速度的增加而增加;外加声场使环隙区和喷泉区的气体流动更加均匀,显著增加环隙区和喷泉区气流的湍动程度,且湍动程度随声压级的增大而显著增大,随声波频率的升高而小幅度降低。     

单孔射流流化床内颗粒混合特性的数值模拟

在欧拉-拉格朗日坐标系下,采用离散单元法对单孔射流流化床内颗粒混合特性进行了数值模拟。引入混合指数对床内轴向及径向布置的颗粒混合质量进行定量分析,并研究了不同表观气速、不同弹性系数对颗粒混合特性的影响。模拟得到了颗粒轴向及径向混合序列图、气体和颗粒速度分布、整床颗粒混合指数分布、参量变化时整床颗粒混合指数分布。结果表明：流化床床层内颗粒混合速度受颗粒内循环能力和颗粒扩散能力的综合作用。单口射流喷动流化床颗粒轴向混合速度主要由颗粒内循环速度决定,颗粒径向混合速度主要由颗粒扩散能力决定。表观气速增大时,颗粒内循环速度增加,从而加快了颗粒轴向混合进程,但对颗粒径向混合影响微弱;弹性系数增大时,颗粒混合速度及混合质量均下降,并且弹性系数增大对颗粒径向混合进程影响小于颗粒轴向混合。     

单孔射流流化床内颗粒混合特性的数值模拟

在欧拉-拉格朗日坐标系下,采用离散单元法对单孔射流流化床内颗粒混合特性进行了数值模拟。引入混合指数对床内轴向及径向布置的颗粒混合质量进行定量分析,并研究了不同表观气速、不同弹性系数对颗粒混合特性的影响。模拟得到了颗粒轴向及径向混合序列图、气体和颗粒速度分布、整床颗粒混合指数分布、参量变化时整床颗粒混合指数分布。结果表明:流化床床层内颗粒混合速度受颗粒内循环能力和颗粒扩散能力的综合作用。单口射流喷动流化床颗粒轴向混合速度主要由颗粒内循环速度决定,颗粒径向混合速度主要由颗粒扩散能力决定。表观气速增大时,颗粒内循环速度增加,从而加快了颗粒轴向混合进程,但对颗粒径向混合影响微弱;弹性系数增大时,颗粒混合速度及混合质量均下降,并且弹性系数增大对颗粒径向混合进程影响小于颗粒轴向混合。     

倒置液固流化床内液固两相流动特性的数值模拟

基于欧拉-欧拉双流体模型,数值模拟倒置液固流化床内液固两相流动行为.数值模拟预测了床内颗粒的速度、浓度分布以及空隙率的变化.研究结果表明颗粒在床内分布呈现非均匀分布,床内形成局部高空隙率的流体团;随着床层高度增加,颗粒轴向速度增大:数值模拟床内空隙率与Renganthan等的实验结果相吻合.     

气固流化床内射流穿透深度的CFD模拟及其实验验证

在经典的Gidaspow无黏性双流体模型中考虑离散颗粒对流体和固体动量守恒方程的影响后,建立了一个具有模拟大规模流化床内气固两相流体动力学特性潜在优势的简化数学模型。在CFX4.4商业化软件平台上通过增加用户自定义子程序考察了二维气固流化床(高2.00 m、宽0.30 m)内射流气速、喷嘴尺寸、环隙气速和静床高度对射流穿透深度的影响,并以树脂颗粒(粒径670 μm、密度1474 kg·m^-3)为研究对象在厚度为0.025 m的矩形床内进行了对比实验。结果表明,选取空隙率为0.8的等高线作为射流边界比较合适;射流穿透深度随射流气速或射流喷口尺寸的增加而增大;射流周围环隙气速由0变到最小流化速度时,射流穿透深度随环隙气速增加而增大,在最小流化速度时达到最大值,然后随环隙气速增加单调减小,当环隙气速大于2.5倍最小流化速度时,射流穿透深度减小程度变缓;在相同射流气速下射流穿透深度随着静床高度的增加而减小,静床高度对射流穿透深度的影响随着射流气速增加呈现扩大的趋势。     

窄筛分颗粒气固流态化特性数值模拟研究

为更好地指导工业生产,了解不同粒径颗粒在气固流化床中的状态以及流化床中颗粒分布情况,针对气固流化床中窄筛分颗粒流态化特性进行数值模拟研究。通过流场模拟软件分析在相同流化床中不同粒径段的颗粒(46～80、106～113、185～221μm)和不同流化床进气速度条件下所能达到的体积分数和流化床层高度以及达到这一指标所需时间,并采用欧拉-欧拉模型和SIMPLE算法计算不同气速条件下的颗粒体积分数、速度分布。结果表明,在相同气速条件下,颗粒粒径增大,导致流化床内颗粒体积分数最高点与最低点的差距变大,颗粒分布不均匀性增加,同时床层整体高度下降,床层内颗粒密度上升,颗粒体积分数下降,流化效果降低;相同颗粒粒径情况下,增加气速可降低流化床内部颗粒的体积分数,增加气体与固体颗粒的接触面积,增强流化效果,但减少了流化床内部颗粒速度矢量分布达到均匀的时间,颗粒分布不均匀性更加明显。     

水平辅助气对喷动床流动特性影响的研究

在上部内径为 195mm柱状、下部为 6 0°锥体的喷动床中水平引入辅助气 ,考察了水平辅助气对流动特性的影响。实验结果发现 ,辅助气的水平引入比竖直或法向引入可以更有效地抑制喷动气体向环流区扩散 ,降低最小喷动气速。在总气速一定的条件下 ,增大辅助气速的比例 ,可以降低喷动区空隙率而使颗粒浓度增大 ,提高颗粒的循环流动量。相比而言 ,喷动气速对喷动区颗粒的流动速度影响较大 ,而水平辅助气速对环流区颗粒的流动速度影响较大     

增压导向式喷动流化庆流动特性的数值模拟

采用双流体理论对增压导向式喷动流化床内喷动区和环形区气固运动速度和近隙率进行数值模拟。计算结果表明：喷动区颗粒速度在初始急布上升而气体速度则急剧下降,进入导向管后趋于平缓,而且颗粒加速程度还与系统压力有关;环形区气体速度在卷吸段增大,进入隔离流区后保持不变,而颗粒速度则一直保持不变;喷动区的空隙率在郑吸段下降,进入导向管后又开始上升。     

循环流化床气固流动行为的数值模拟

采用欧拉-欧拉双流体模型,在Fluent数值模拟平台上对循环湍动流化床进行了研究。采用Gidaspow模型分段描述密相湍动和稀相循环输送区气固的相互作用,考察了反应器内压力、颗粒浓度等气固湍动特性参数的变化。计算流体力学(CFD)的模拟结果表明:反应器中压力分布较为均匀;固体颗粒相和气体相间隙成絮状分布,在轴向中心区域颗粒浓度分布较为均匀;边壁区域颗粒浓度变化较大,存在强烈的气固相互作用。     

离心流化床初始流化状态的研究(Ⅰ)基本理论

通过简化求解离心流化床连续介质模型基本控制方程,获得了初始流化速度、压力、空隙率、空隙气速、床层膨胀和床层压降的计算方程式。理论预报的临界流化速度和床层压降与实验结果吻合得很好。揭示了离心流化床随流速增大由表面逐层初始流化;流化后各半径处流化程度不同。理论分析还表明气体压缩性的影响随着床体转速的增大而增大。     

新颖环形喷动床颗粒喷动特性实验研究

一种新颖的环形喷动床由内外两个不同内径、同心的垂立圆筒组成,在环形空间底部设置多个喷口,在喷口两侧布置倾斜的导流板.研究颗粒在这种喷动床内的流动特性,探讨喷口结构、颗粒种类以及床内载料量对环形喷动床颗粒喷动特性的影响.实验结果表明:颗粒在环形喷动床内分为三个明显不同的区域,即颗粒填充移动区、密相喷动流化区以及稀相夹带区.当颗粒出现分区喷动后,随床内载料量的增多,填充移动区的高度维持不变,始终等于导流板的高度,而密相喷动区的高度不断增加.风量和颗粒种类对床层最大喷动量、密相喷动高度以及床层压力分布规律有着十分重要的影响.采用不同的喷口结构时,在相同的载料量下,直向喷口的密相喷动区高度更大,而且床内各测点的平均压力大于采用斜向喷口时的相应测点压力.     

喷动床内气固二相流动行为的计算模拟

采用双流体模型结合颗粒动理学理论对喷动床内气固二相流体流动行为进行了计算模拟研究。模型中运用颗粒动理学理论描述颗粒相应力封闭流体控制方程,使用Gidaspow曳力模型描述气固相间作用。喷动床内颗粒在浓相区的体积分数很大,采用Schaeffer′s模型描述颗粒间的摩擦应力。模拟计算结果表明,喷动床内分喷射区、喷泉区、环隙区3个区域,在射流入口处形成一个瓶颈。模拟计算得到的颗粒速度和空隙度分布与实验数据进行比较,计算结果与实验结果吻合较好。     

Aerodynamics of a novel rotating jet spouted bed

A novel rotating jet spouted bed (RJSB) is developed and tested. It consists of a rotating air distributor with two radially located spouting air nozzles. The effects of bed height, distributor rotational speed, nozzle diameter and particle properties on the flow characteristics were examined. Various flow regimes were mapped as functions of distributor rotational speed and superficial air velocity for different materials and column dimensions. Empirical correlations were developed for the minimum spouting velocity, peak pressure drop and steady spouting pressure drop.     

Hydrodynamics of a Novel Biomass Autothermal Fast Pyrolysis Reactor: Flow Pattern and Pressure Drop

A novel biomass, autothermal, fast pyrolysis reactor with a draft tube and an internal dipleg dividing the reactor into two interconnected beds is proposed. This internally interconnected fluidized beds (IIFB) reactor is designed to produce high‐quality bio‐oil using catalysts. Meanwhile, the pyrolysis by‐products, i.e., char, coke and non‐condensable gases, are expected to burn in the combustion bed to provide the heat for the pyrolysis. On the other hand, the catalysts can be regenerated simultaneously. In this study, experiments on the hydrodynamics of a cold model IIFB reactor are reported. Geldart group B and D sand particles were used as the bed materials. The effects of spouting and fluidizing gas velocities, particle size, static bed height and the total pressure loss coefficient of the pyrolysis bed exit, on the flow patterns and pressure drops of the two interconnected beds are studied. Six distinct flow patterns, i.e., fixed bed (F), periodic spouted/bubbling bed (PS/B), spouted bed with aeration (SA), spout‐fluidized bed (SF), spout‐fluidized bed with slugging (SFS) and spouted bed with backward jet (SBJ) are identified. The investigations on the pressure drops of the two beds show that both of them are seen to increase at first (mainly in the F flow pattern), then to decrease (mainly in the PS/B and SA flow patterns) and finally to increase again (mainly in the SA and SF flow patterns), with the increase of the spouting gas velocity. It is observed that a larger particle size and lower static bed height lead to lower pressure drops of the two beds.     

Particle velocity and solids circulation rate in a jet-spouted bed

Radial distribution of particle velocities, solids circulation rate and radial variation in bed voidage in a jet-spouted bed were investigated in a 0.2 m diameter conical-cylindrical column. The upward particle velocity is strongly dependent on gas velocity and its radial profile is the Gaussian. The solids circulation rates are of the same order of magnitude as those in a conventional spouted bed and are proportional to the gas velocity. Estimation of the variation in bed voidage in the radial direction revealed that the annulus voidage of about 0.90 was greater than the spout voidage of around 0.70. This tendency is contrary to that in a conventional spouted bed.     

Cavity formation and breakup forces in conical spouted beds

A method has been developed to deduce a “breakup” force in a packed bed based on measured pressure drop and internal cavity size hysteresis data in a conical spouted bed. The pressure drop over the vertical jet is estimated by the Eulerian-Eulerian two-fluid model using the commercial Fluent software. The pressure drop over the packed bed is extracted from the measured total pressure drop following a flow rate descending process in the spouted bed, while the “breakup” force is determined from the combination of measured total pressure drop and internal jet height following the flow ascending process, the simulated pressure drop over the gas jet and the pressure drop over the loosely packed upper bed section. Such a proposed method can be applied in the future to develop a generalized expression for the “breakup” force in spouted beds and other packed bed systems where a vertical fluid jet is issued into the packed particles.     

Jet penetration depth in a two-dimensional spout-fluid bed

The jet penetration depth was proposed to be an important parameter to describe the jet action during the chemical process of spout-fluid bed coal gasification. A two-dimensional cold model of a spout-fluid bed coal gasifier with its cross section of and height of 2000 mm was established to investigate the jet penetration depth. Four types of Geldart group D particles were used as bed materials. A multi-channel pressure sampling system and a high-resolution digital CCD camera were employed for experimental investigations. The effects of spouting gas velocity, spout nozzle diameter, static bed height, particle property and fluidizing gas flow rate on the jet penetration depth have been systematically studied by pressure signal analysis and image processing. Experimental results indicate that the jet penetration depth increases with increasing spouting gas velocity and spout nozzle diameter, while it decreases with increasing particle density, particle diameter, static bed height and fluidizing gas flow rate. Additional, a new correlation considered all of the above effects especially static bed height and fluidizing gas flow rate, was developed for predicting the jet penetration depth in spout-fluid beds. The correlation was compared with published experimental data or correlations, which was in well agreement with the present experimental results and some other references.     

三维喷动床内异径干湿颗粒混合特性数值模拟

基于计算流体力学-离散单元法,建立了三维喷动床内气固两相流数学模型,采用Fortran语言编制了并行数值模拟程序。对三维喷动床内两种不同直径的干颗粒及湿颗粒的混合特性进行了数值模拟,并从颗粒角度分析了双组分颗粒的运动机制。利用Lacey混合指数对床内整体以及特定区域的混合程度进行了定量分析,并研究了液桥体积、颗粒密度比以及表观气速对异径颗粒混合的影响。结果表明：在单孔射流喷动床内,干湿两种颗粒流动方式相似,湿颗粒无明显的聚团现象;液桥力对小直径的颗粒影响较大,使不同直径湿颗粒速度差减小;环隙区内颗粒的混合是影响整床颗粒混合的关键因素;液桥体积对颗粒混合的影响较大,对颗粒密度比以及表观气速的影响有限。     

Spoutable bed height and pressure fluctuation of a novel annular spouted bed with V-shaped deflector

A novel annular spouted bed consisting of two homocentric upright cylinders with different diameters was developed. The nozzles and V-shaped deflectors were located in the bottom of annular space between the inner and outer cylinders. The effects of hold-up, bed material, total flowrate and nozzle structure on the hydrodynamic characteristics of the novel annular spouted bed were investigated. The results show that there exist three different zones for the particle flow in the annular spouted bed: the moving packed zone, the dense-phase spouted fluidizing zone and the dilute-phase zone. With the increase of hold-ups, the height of the dense-phase spouted fluidizing zone tends to increase in the annular spouted bed, while the moving packed zone is only limited within the V-shaped deflectors. The maximum spoutable amount for high air flowrate is larger than that for low air flowrate. Both the spoutable bed height and the local mean relative pressure for high air flowrate are higher than those for low air flowrate at the same hold-ups of particles. The nozzle structure also has important effects on the spoutable bed height and the local relative pressure in the annular spouted bed.