Ti6Al4V合金的低温超塑性拉伸变形行为

在700℃-850℃的温度范围内对Ti-6％Al-4％V（质量分数）合金板材进行超塑性拉伸试验,研究了应变速率为3×10^-4-5×10^-3s^-1条件下的拉伸变形行为．结果表明：Ti6Al4V合金在空气中表现出良好的低温超塑性变形能力．在800℃初始应变速率ε=5×10^-4s^-1条件下,延伸率达到536％．在较低的700℃下变形（ε=5×10^-4s^-1）,延伸率仍然超过了300％．在整个变形温度区间内,应变速率敏感性指数m均为0．3左右,最大值为0．63、在850℃变形激活能与晶界自扩散激活能十分相近,表明晶界扩散控制的品界滑动是超塑性变形的主要机制．在700-750℃,变形激活能远大于晶界自扩散激活能,位错运动是激活能升高的原因．在800℃变形的激活能介于两者之间,表明随着温度的降低变形机制逐渐发生改变．     

Ti-15-3钛合金超塑行为研究

为系统了解Ti-15-3合金的超塑性,研究了固溶态和两种不同变形量冷轧态的Ti-15-3合金板材在700～800 ℃和1×10-4 ～3×10-3s-1应变速率范围内的超塑性行为.结果表明:Ti-15-3合金具有较好的超塑性能,冷轧态合金的延伸率均优于固溶态,且随着板材冷轧变形量的增大而增大;各应变速率下,该合金都在780 ℃时获得最大延伸率和应变速率敏感性指数.在780 ℃和1×10-4s-1条件下拉伸时,冷轧变形量为52%的Ti-15-3合金板材获得了370%的延伸率,m值为O.56;变形温度和速率对合金的超塑性能影响很大,合金的延伸率在730～780 ℃范围内随温度的升高和应变速率的降低而升高,合金的流变应力则随之下降.     

异步轧制AZ31镁合金板材的超塑性工艺及变形机制

经过异步轧制工艺获得AZ31镁合金薄板。在300~450℃范围内,分别通过5×10-3,1×10-3s-1和5×10-4s-1不同应变速率进行高温拉伸实验研究其超塑性变形行为,计算应变速率敏感指数m值、超塑性变形激活能Q及门槛应力σ0值。通过EBSD分析和扫描电镜观察拉伸断裂后的断口形貌,分析AZ31镁合金的超塑性变形机制。结果表明:AZ31镁合金的塑性变形能力随着变形温度的升高及应变速率的降低而增强。当拉伸温度为400℃、m=0.72、应变速率为5×10-4s-1时,AZ31具有良好的超塑性,伸长率最大为206%。温度为400℃时,异步轧制AZ31镁合金的超塑性变形是以晶格扩散控制的晶界滑移和基面滑移共同完成的。     

2A97 铝锂合金超塑变形规律及其本构方程

目的研究2A97铝锂合金在390~470℃温度范围和3×10-4~3×10-2s-1应变速率范围内的超塑变形行为,揭示温度和应变速率对延伸率和峰值应力的影响规律,并建立超塑拉伸变形本构方程。方法采用单轴超塑拉伸试验方法进行研究。结果当变形应变速率低于3×10-3s-1时,2A97铝锂合金真应力-真应变曲线呈现稳态流变特征;当应变速率高于3×10-3s-1时,则呈现软化特征。在450℃,应变速率为1×10-3s-1条件下,达到最大延伸率600%。结论 2A97铝锂合金具有良好的超塑变形性能,其应变速率敏感性指数m平均值为0.35,超塑变性激活能Q值为145.87 k J/mol,远高于纯铝自扩散激活能65.6 k J/mol,表明此时铝锂合金变形机制仍以晶内滑移为主。     

Cu－Zn－Al形状记忆合金的超塑性研究

用超塑性拉伸试验方法，研究了加入晶粒细化剂Ｚｒ的冷变形Ｃｕ－２２．６７％Ｚｎ－４．５９％Ａｌ形状记亿合金的短暂超塑性变形．在６００℃，以初始应变速率ε＝５．５５×１０－４ｓ－１进行拉伸试验可获得优良的超塑性性能，延伸率δ＝４６０％．超塑性变形过程中激活能为７４．４ＫＪ／ｍｏｌ，与铜沿晶自扩散激活能值接近．从而认为该合金的超塑性变形机制为晶界的滑移和迁移过程，这一结论与金相观察及断口分析相一致     

TC4-DT合金的超塑性变形及其本构方程

采用CMT4104电子万能拉伸试验机分别进行温度为870℃,应变速率为3.3×10-4s-1的恒应变速率和温度为850~890℃,应变速率为3.3×10-5~3.3×10-3s-1的应变速率循环法超塑性拉伸实验。结果表明:在变形过程中存在动态回复与动态再结晶现象,并采用Avrami方程描述了动态再结晶动力学行为;基于应变速率循环法获得了TC4-DT合金的本构模型,再通过1stopt软件加以回归拟合,得到较为精确的TC4-DT合金超塑性变形本构方程。     

纳米Ni和Ni/SiCp纳米复合材料的超塑性

研究了用电沉积方法制备的纳米Ni和Ni/SiCp纳米复合材料的超塑特性,在试验温度410℃和450℃,应变速率为8.3×10-4s-1～5×10-2s-1的条件下,纳米Ni和Ni/SiCp纳米复合材料均表现出超塑性.当温度为450℃、应变速率为1.67×10-2s-1时,在Ni/SiCp中获得最大延伸率为836%;在同样的温度下应变速率为1.67×10-3s-1时纳米Ni获得最大延伸率为550%.对超塑性变形后组织的分析表明,晶界滑移是主要变形机制,晶粒长大至亚微米/微米量级后,变形机制是位错协调晶界滑移和位错滑移塑性.     

5A90铝锂合金超塑性变形的组织演变及变形机理

采用光学显微镜、扫描电镜、电子背散射衍射以及高温拉伸实验研究了工业化制备的5A90铝锂合金超塑性板材变形过程中的组织演变及变形机理。结果表明:在高温拉伸前对板材进行450℃/30min再结晶退火后,在温度为475℃、应变速率为8×10-4s-1的适宜超塑性变形条件下,可使伸长率由原始状态的480%提高至880%。整个超塑性变形过程展现出不同的变形机制:初始阶段(ε≤0.59),板材以形变组织为主,晶粒取向差逐渐增大,位错运动为该阶段的主要变形机制。当真应变达到0.59时,动态再结晶开始发生,晶粒取向差继续增大,晶界滑动开始启动。当真应变大于1.55时,晶粒继续长大,但长大幅度不大且保持等轴状,该阶段变形机制以晶界滑动为主。     

应变速率循环法构建TC4-DT钛合金本构方程

采用应变速率循环法在超塑拉伸机上对TC4-DT钛合金进行三组高温超塑性拉伸实验,变形温度为850~890℃,应变速率为3.3×10-5~3.3×10-3s-1。通过对拉伸实验数据的分析计算出TC4-DT钛合金动态再结晶激活能,并利用Arrhenius模型构建TC4-DT高温条件下的超塑性本构方程。结果表明:TC4-DT钛合金的流动应力对变形温度较为敏感,随着温度的升高,流变应力逐渐减小,软化机制愈发明显,870℃附近的超塑性较好,伸长率达到554%。     

铸锭铝合金Al-Cu-Mg-Ti高应变速率超塑性

采用常规熔铸、热处理、小挤压比挤压及轧制这一低成本并适合于工业化规模应用的路线,研制了一种具有高应变速率超塑性的铸锭铝合金Al-Cu-Mg-Ti.拉伸试验结果表明在温度为793K、初始应变速率为3.16×10-1s-1的拉伸变形条件下,其超塑伸长率为218%,流变应力为32.5MPa.断面及表面形貌SEM分析和初熔行为的DSC分析表明,该合金高应变速率超塑性变形来自于晶界滑动和位错滑移,与液相没有关系.     

Insertion of triangulated surfaces into a meccano tetrahedral discretization by means of mesh refinement and optimization procedures

In this paper, we present a new method for inserting several triangulated surfaces into an existing tetrahedral mesh generated by the meccano method. The result is a conformal mesh where each inserted surface is approximated by a set of faces of the final tetrahedral mesh. First, the tetrahedral mesh is refined around the inserted surfaces to capture their geometric features. Second, each immersed surface is approximated by a set of faces from the tetrahedral mesh. Third, following a novel approach, the nodes of the approximated surfaces are mapped to the corresponding immersed surface. Fourth, we untangle and smooth the mesh by optimizing a regularized shape distortion measure for tetrahedral elements in which we move all the nodes of the mesh, restricting the movement of the edge and surface nodes along the corresponding entity they belong to. The refining process allows approximating the immersed surface for any initial meccano tetrahedral mesh. Moreover, the proposed projection method avoids computational expensive geometric projections. Finally, the applied simultaneous untangling and smoothing process delivers a high‐quality mesh and ensures that the immersed surfaces are interpolated. Several examples are presented to assess the properties of the proposed method.     

Certification Institutions Expected to Update and Transfer Information on Present Standards

Standards are the basis for production enterprises to organize production, ex-factory inspection, trade (delivery) and technical exchanges, product certification, quality arbitration and supervision.……     

Flow calorimeter for enthalpy increment measurements on condensed gases

A flow calorimeter for enthalpy increment measurements on condensed gases is presented. A better knowledge of the properties of the liquefied natural gas is needed, and therefore a liquid loop has been designed for our flow calorimeter. The fluid loop in the calorimeter is designed in order to avoid the two-phase region, since two phases would give compositional disturbances in the measurements. The avoidance of the two-phase region is made possible by increasing the pressure of the test fluid after the measurement section, then heating the fluid at super-critical pressure past the critical point. Finally, the fluid is throttled to the low-pressure gas state at the inlet condition of the compressor that circulates the fluid. To perform the pressure increase, a new cryogenic pump has been designed. To evaluate the new equipment, measurements were taken on liquid ethane over the temperature range 146–256 K at pressure between 0.9 and 5.1 MPa.     

Refrigerators Enter a New Era of Health Preservation Frestech initiates the establishment of China's first standard for household sterilization refrigerators

On November 30, 2007, the China Association for Standardization (CAS) held a press conference at Beijing Diaoyutai State Guest House. Leaders from the China Household Electric Appliance Research Institute, the China Household Electric Appliance Association, and the China Consumers' Association attended and made speeches.……     

Optimum-Simulation von Ernteprozessen

Zusammenfassung Bei der Gestaltung von Ernteprozessen — beispielsweise des Prozesses Mähdrusch, Körnertransport und -abnahme — als transportverbundene Fließarbeitsverfahren mit mindestens zwei verschiedenen Arbeitsmitteln gibt es einen großen Optimierungsspielraum. Solche Prozesse sind mehrstufige Bedienungsprozesse mit gemischter Anordnung der Bedienungseinrichtungen. Außerdem besitzen sie stark ausgeprägte räumliche Aspekte. Es wird vor allem gezeigt, welche Merkmale solcher Prozesse in Simulationsmodellen abgebildet sein müssen, welche Zielgrößen in Abhängigkeit von welchen Einflußgrößen unter Berücksichtigung welcher Prozeßbedingungen ermittelt werden sollten und wie der Bewertungsprozeß zur Ermittlung der gewünschten Informationen gestaltet werden muß.     

A study of centrifugal cast high boron high speed steel

In the present study a high‐boron high speed steel (HSS) roll material was designed. Many expensive alloy elements have been substituted by cheap boron alloy, and high‐boron high speed steel roll has been manufactured by centrifugal casting method. The microstructures, mechanical properties and wear resistance of centrifugal casting high‐boron high speed steel roll have been investigated by optical microscopy (OM), scanning electron microscopy (SEM), and X‐ray diffraction (XRD) analysis, hardness test, impact test and wear test. The results indicated that the solidification microstructures of high‐boron high speed steel roll consisted of M₂(B,C), (W,Mo)₂(B,C), M₃(B,C), M₂₃(B,C)₆ type borocarbides and martensite, a small amount of retained austenite. Borocarbides were continuously distributed over the grain boundary. After quenching from 1050 °C, local broken network appeared in partial borocarbides, and fine secondary borocarbide precipitated from the matrix. After tempering from 525 °C, the amount of precipitated borocarbide increased significantly. After heat treatment, the hardness of high‐boron high speed steel roll excelled 60 HRC, and its impact toughness excelled 8.0 J/cm². The single groove steel rolling amount of high‐boron high speed steel rolls increases by 500% than that of bainite cast iron roll, when the rolls are used in K₁ mill housing of bar mill.     

Thixotropy of Systems with Shear Thinning and Plastic Flow Behavior

The definition of the thixotropy is a decrease in viscosity with time in shear and a subsequent recovery of viscosity after the shear deformation is removed.We ...     

Brainstorming for ISO Strategy 2016-2020

正Responding to ISO’s appeal for survey for the to-be-developed ISO Strategy Plan for 2016-2020,SAC hosted a special workshop over the needs and comments of various fi elds on June 8 in Beijing.The workshop was attended by ISO President-elect and Ansteel General Manager Zhang Xiaogang,SAC Vice-Administrator Yu Xinli,and 30 experts from     

CNAS Passes APLAC's PTP Review

正The review group of Asia Pacific Laboratory Accreditation Cooperation(APLAC)carried out a 4-day peer review of the proficiency testing provider(PTP)for China National Accreditation Service for Conformity Assessment(CNAS)from July 28 to 31,2014.CNAS passed the PTP review with excellent performance.Two senior peer reviewers of APLAC made a comprehensive,rigorous and detailed review of CNAS’s PTP accreditation activities,and made the on-spot inspection of the review groups in Shanghai and Shenzhen respectively.