Highly Sensitive Chemical‐Vapor Sensor Based on Thin‐Film Organic Field‐Effect Transistors with Benzothiadiazole‐Fused‐Tetrathiafulvalene

The synthesis of a new tetrathiafulvalene derivative with an electron‐withdrawing benzothiadiazole moiety and its use in thin‐film organic field‐effect transistors (OFETs) are reported. Compared to reported OFETs with other TTF derivatives, a high hole mobility up to 0.73 cm² V^?1 s^?1, low off‐current and high on/off ratio up to 10⁵ are demonstrated. In addition, the developed OFETs show fast responsiveness toward chemical vapors of DECP (diethyl chlorophosphate) or POCl₃ which are simulants of phosphate‐based nerve agents. In contrast to previously reported OFET‐based sensors, off‐current is used as the output signal, which increases quickly upon exposure to either DECP or POCl₃ vapors. High sensitivity is demonstrated toward DECP and POCl₃ vapors, with concentrations as low as 10 ppb being detected. These OFETs are also responsive to TNT vapor. The sensing mechanisms for the new type of OFET are discussed.     

Mercury‐Mediated Organic Semiconductor Surface Doping Monitored by Electrolyte‐Gated Field‐Effect Transistors

Surface doping allows tuning the electronic structure of semiconductors at near‐surface regime and is normally accomplished through the deposition of an ultrathin layer on top or below the host material. Surface doping is particularly appealing in organic field‐effect transistors (OFETs) where charge transport takes place at the first monolayers close to the dielectric surface. However, due to fabrication restrictions that OFET architecture imparts, this is extremely challenging. Here, it is demonstrated that mercury cations, Hg²⁺, can be exploited to control doping levels at the top surface of a thin film of a p‐type organic semiconductor blended with polystyrene. Electrolyte‐ or water‐gated field‐effect transistors, which have its conductive channel at the top surface of the organic thin film, turn out to be a powerful tool for monitoring the process. A positive shift of the threshold voltage is observed in the devices upon Hg²⁺ exposure. Remarkably, this interaction has been proved to be specific to Hg²⁺ with respect to other divalent cations and sensitive down to nanomolar concentrations. Hence, this work also opens new perspectives for employing organic electronic transducers in portable sensors for the detection of an extremely harmful water pollutant without the need of using specific receptors.     

Organic Field‐Effect Transistors and Unipolar Logic Gates on Charged Electrets from Spin‐On Organosilsesquioxane Resins

Controllable shifting of threshold voltage and modulation of current in organic field‐effect transistors (OFETs) is demonstrated, resulting in the formation of unipolar inverters by making use of space‐charge electrets. Prior to the deposition of the organic semiconductor (OSC), negative corona charges are injected and trapped in the bulk of the organosilsesquioxane glass resin gate dielectrics. The effective surface potential is controlled by the corona‐charging and subsequent annealing process. It is found that the shift of the transfer characteristics is governed by the electrostatic induction effects of the charged gate electrets, and this observed shift can be related to the surface potential of the layer next to the transistor channel. The process control, efficiency, and long‐term stability of charge storage in spin‐on organosilsesquioxane glass resins are sufficient to enable the construction of simple unipolar inverters and to allow for circuit tuning. New OFET unipolar inverters with an enhancement‐mode driver and a depletion‐mode load are presented, composed of only two simple OFETs with the same channel dimensions and the same p‐type OSC on charged electrets. This design allows the implementation of full‐swing organic logic circuits and illustrates a potential process simplification for organic electronics.     

Monitoring the Channel Formation in Organic Field‐Effect Transistors via Photoinduced Charge Transfer

Conducting channel formation in organic field‐effect transistors (OFETs) is considered to happen in the organic semiconductor layer very close to the interface with the gate dielectric. In the gradual channel approximation, the local density of accumulated charge carriers varies as a result of applied gate bias, with the majority of the charge carriers being localized in the first few semiconductor monolayers close to the dielectric interface. In this report, a new concept is employed which enables the accumulation of charge carriers in the channel by photoinduced charge transfer. An OFET employing C₆₀ as a semiconductor and divinyltetramethyldisiloxane‐bis(benzocyclobutene) as the gate dielectric is modified by a very thin noncontinuous layer of zinc‐phthalocyanine (ZnPc) at the semiconductor/dielectric interface. With this device geometry, it is possible to excite the phthalocyanine selectively and photogenerate charges directly at the semiconductor/dielectric interface via photoinduced electron transfer from ZnPc onto C₆₀. Thus the formation of a gate induced and a photoinduced channel in the same device can be correlated.     

Digital‐Inverter Amine Sensing via Synergistic Responses by n and p Organic Semiconductors

Chemiresistors and sensitive organic field‐effect transistors (OFETs) have been substantially developed as cheap, scalable, and versatile sensing platforms. While new materials are expanding OFET sensing capabilities, the device architectures have changed little. Higher order logic circuits utilizing OFETs sensitive to amine vapors are presented. The circuits depend on the synergistic responses of paired p‐ and n‐channel organic semiconductors, including a rare analyte‐induced current increase by the n‐channel semiconductor. This is the first step towards ‘intelligent sensors’ that utilize analog signal changes in sensitive OFETs to produce direct digital readouts suitable for further logic operations.     

Tuning Contact Resistance in Top‐Contact p‐Type and n‐Type Organic Field Effect Transistors by Self‐Generated Interlayers

Contact resistance significantly limits the performance of organic field‐effect transistors (OFETs). Positioning interlayers at the metal/organic interface can tune the effective work‐function and reduce contact resistance. Myriad techniques offer interlayer processing onto the metal pads in bottom‐contact OFETs. However, most methods are not suitable for deposition on organic films and incompatible with top‐contact OFET architectures. Here, a simple and versatile methodology is demonstrated for interlayer processing in both p‐ and n‐type devices that is also suitable for top‐contact OFETs. In this approach, judiciously selected interlayer molecules are co‐deposited as additives in the semiconducting polymer active layer. During top contact deposition, the additive molecules migrate from within the bulk film to the organic/metal interface due to additive‐metal interactions. Migration continues until a thin continuous interlayer is completed. Formation of the interlayer is confirmed by X‐ray photoelectron spectroscopy (XPS) and cross‐section scanning transmission electron microscopy (STEM), and its effect on contact resistance by device measurements and transfer line method (TLM) analysis. It is shown that self‐generated interlayers that reduce contact resistance in p‐type devices, increase that of n‐type devices, and vice versa, confirming the role of additives as interlayer materials that modulate the effective work‐function of the organic/metal interface.     

Highly Sensitive and Selective Biosensors Based on Organic Transistors Functionalized with Cucurbit[6]uril Derivatives

Biosensors based on a field‐effect transistor platform allow continuous monitoring of biologically active species with high sensitivity due to the amplification capability of detected signals. To date, a large number of sensors for biogenic substances have used high‐cost enzyme immobilization methods. Here, highly sensitive organic field‐effect transistor (OFET)‐based sensors functionalized with synthetic receptors are reported that can selectively detect acetylcholine (ACh⁺), a critical ion related to the delivery of neural stimulation. A cucurbit[6]uril (CB[6]) derivative, perallyloxyCB[6] ((allyloxy)₁₂CB[6], AOCB[6]), which is soluble in methanol but insoluble in water, has been solution‐deposited as a selective sensing layer onto a water‐stable p‐channel semiconductor, 5,5′‐bis‐(7‐dodecyl‐9H‐fluoren‐2‐yl)‐2,2′‐bithiophene layer. The OFET‐based sensors exhibit a detection limit down to 1 × 10^–12 m of ACh⁺, which is six orders of magnitude lower than that of ion‐selective electrode‐based sensors. Moreover, these OFET‐based sensors show highly selective discrimination of ACh⁺ over choline (Ch⁺). The findings demonstrate a viable method for the fabrication of OFET‐based biosensors with high sensitivity and selectivity, and allow for practical applications of OFETs as high‐performance sensors for biogenic substances.     

High‐Speed Organic Single‐Crystal Transistor Responding to Very High Frequency Band

Although high carrier mobility organic field‐effect transistors (OFETs) are required for high‐speed device applications, improving the carrier mobility alone does not lead to high‐speed operation. Because the cut‐off frequency is determined predominantly by the total resistance and parasitic capacitance of a transistor, it is necessary to miniaturize OFETs while reducing these factors. Depositing a dopant layer only at the metal/semiconductor interface is an effective technique to reduce the contact resistance. However, fine‐patterning techniques for a dopant layer are still challenging especially for a top‐contact solution‐processed OFET geometry because organic semiconductors are vulnerable to chemical damage by solvents. In this work, high‐resolution, damage‐free patterning of a dopant layer is developed to fabricate short‐channel OFETs with a dopant interlayer inserted at the contacts. The fabricated OFETs exhibit high mobility exceeding 10 cm² V^?1 s^?1 together with a reasonably low contact resistance, allowing for high frequency operation at 38 MHz. In addition, a diode‐connected OFET shows a rectifying capability of up to 78 MHz at an applied voltage of 5 V. This shows that an OFET can respond to the very high frequency band, which is beneficial for long‐distance wireless communication.     

Polymer‐Based Organic Field‐Effect Transistors with Active Layers Aligned by Highly Hydrophobic Nanogrooved Surfaces

In this study, polymer‐based organic field‐effect transistors (OFETs) that exhibit alignment‐induced mobility enhancement, very small device‐to‐device variation, and high operational stability are successfully fabricated by a simple coating method of semiconductor solutions on highly hydrophobic nanogrooved surfaces. The highly hydrophobic nanogrooved surfaces (water contact angle >110°) are effective at inducing unidirectional alignment of polymer backbone structures with edge‐on orientation and are advantageous for realizing high operational stability because of their water‐repellent nature. The dewetting of the semiconductor solution is a critical problem in the thin film formation on highly hydrophobic surfaces. Dewetting during spin coating is suppressed by surrounding the hydrophobic regions with hydrophilic ones under appropriate designs. For the OFET array with an aligned terrace‐phase active layer of poly(2,5‐bis(3‐hexadecylthiophene‐2‐yl)thieno[3,2‐b]thiophene), the hole mobility in the saturation regime of 30 OFETs with channel current direction parallel to the nanogrooves is 0.513 ± 0.018 cm² V^?1 s^?1, which is approximately double that of the OFETs without nanogrooves, and the intrinsic operational stability is comparable to the operational stability of amorphous‐silicon field‐effect transistors. In other words, alignment‐induced mobility enhancement and high operational stability are successfully achieved with very small device‐to‐device variation. This coating method should be a promising means of fabricating high‐performance OFETs.     

Solution‐Processed Monolayer Organic Crystals for High‐Performance Field‐Effect Transistors and Ultrasensitive Gas Sensors

This work innovatively develops a dual solution‐shearing method utilizing the semiconductor concentration region close to the solubility limit, which successfully generates large‐area and high‐performance semiconductor monolayer crystals on the millimeter scale. The monolayer crystals with poly(methyl methacrylate) encapsulation show the highest mobility of 10.4 cm² V^?1 s^?1 among the mobility values in the reported solution‐processed semiconductor monolayers. With similar mobility to multilayer crystals, light is shed on the charge accumulation mechanism in organic field‐effect transistors (OFETs), where the first layer on interface bears the most carrier transport task, and the other above layers work as carrier suppliers and encapsulations to the first layer. The monolayer crystals show a very low dependency on channel directions with a small anisotropic ratio of 1.3. The positive mobility–temperature correlation reveals a thermally activated carrier transport mode in the monolayer crystals, which is different from the band‐like transport mode in multilayer crystals. Furthermore, because of the direct exposure of highly conductive channels, the monolayer crystal based OFETs can sense ammonia concentrations as low as 10 ppb. The decent sensitivity indicates the monolayer crystals are potential candidates for sensor applications.     

Synergistic Use of Pyridine and Selenophene in a Diketopyrrolopyrrole‐Based Conjugated Polymer Enhances the Electron Mobility in Organic Transistors

To achieve semiconducting materials with high electron mobility in organic field‐effect transistors (OFETs), low‐lying energy levels (the highest occupied molecular orbital (HOMO) and the lowest unoccupied molecular orbital (LUMO)) and favorable molecular packing and ordering are two crucial factors. Here, it is reported that the incorporation of pyridine and selenophene into the backbone of a diketopyrrolopyrrole (DPP)‐based copolymer produces a high‐electron‐mobility semiconductor, PDPPy‐Se. Compared with analogous polymers based on other DPP derivatives and selenophene, PDPPy‐Se features a lower LUMO that can decrease the electron transfer barrier for more effective electron injection, and simultaneously a lower HOMO that, however, can increase the hole transfer barrier to suppress the hole injection. Combined with thermal annealing at 240 °C for thin film morphology optimization to achieve large‐scale crystallite domains with tight molecular packing for effective charge transport along the conducting channel, OFET devices fabricated with PDPPy‐Se exhibit an n‐type‐dominant performance with an electron mobility (μ_e) as high as 2.22 cm² V^?1 s^?1 and a hole/electron mobility ratio (μ_h/μ_e) of 0.26. Overall, this study demonstrates a simple yet effective approach to boost the electron mobility in organic transistors by synergistic use of pyridine and selenophene in the backbone of a DPP‐based copolymer.     

Hydrocarbons‐Driven Crystallization of Polymer Semiconductors for Low‐Temperature Fabrication of High‐Performance Organic Field‐Effect Transistors

While many high‐performance polymer semiconductors are reported for organic field‐effect transistors (OFETs), most require a high‐temperature postdeposition annealing of channel semiconductors to achieve high performance. This negates the fundamental attribute of OFETs being a low‐cost alternative to conventional high‐cost silicon technologies. A facile solution process is developed through which high‐performance OFETs can be fabricated without thermal annealing. The process involves incorporation of an incompatible hydrocarbon binder or wax into the channel semiconductor composition to drive rapid phase separation and instantaneous crystallization of polymer semiconductor at room temperature. The resulting composite channel semiconductor film manifests a nano/microporous surface morphology with a continuous semiconductor nanowire network. OFET mobility of up to about 5 cm² V^?1 s^?1 and on/off ratio ≥ 10⁶ are attained. These are hitherto benchmark performance characteristics for room‐temperature, solution‐processed polymer OFETs, which are functionally useful for many impactful applications.     

Self‐Assembled,Millimeter‐Sized TIPS‐Pentacene Spherulites Grown on Partially Crosslinked Polymer Gate Dielectric

Here, a highly crystalline and self‐assembled 6,13‐bis(triisopropylsilylethynyl) pentacene (TIPS‐Pentacene) thin films formed by simple spin‐coating for the fabrication of high‐performance solution‐processed organic field‐effect transistors (OFETs) are reported. Rather than using semiconducting organic small‐molecule–insulating polymer blends for an active layer of an organic transistor, TIPS‐Pentacene organic semiconductor is separately self‐assembled on partially crosslinked poly‐4‐vinylphenol:poly(melamine‐co‐formaldehyde) (PVP:PMF) gate dielectric, which results in a vertically segregated semiconductor‐dielectric film with millimeter‐sized spherulite‐crystalline morphology of TIPS‐Pentacene. The structural and electrical properties of TIPS‐Pentacene/PVP:PMF films have been studied using a combination of polarized optical microscopy, atomic force microscopy, 2D‐grazing incidence wide‐angle X‐ray scattering, and secondary ion mass spectrometry. It is finally demonstrated a high‐performance OFETs with a maximum hole mobility of 3.40 cm² V^?1 s^?1 which is, to the best of our knowledge, one of the highest mobility values for TIPS‐Pentacene OFETs fabricated using a conventional solution process. It is expected that this new deposition method would be applicable to other small molecular semiconductor–curable polymer gate dielectric systems for high‐performance organic electronic applications.     

A High‐Capacitance Salt‐Free Dielectric for Self‐Healable,Printable, and Flexible Organic Field Effect Transistors and Chemical Sensor

Printable and flexible electronics attract sustained attention for their low cost, easy scale up, and potential application in wearable and implantable sensors. However, they are susceptible to scratching, rupture, or other damage from bending or stretching due to their “soft” nature compared to their rigid counterparts (Si‐based electronics), leading to loss of functionality. Self‐healing capability is highly desirable for these “soft” electronic devices. Here, a versatile self‐healing polymer blend dielectric is developed with no added salts and it is integrated into organic field transistors (OFETs) as a gate insulator material. This polymer blend exhibits an unusually high thin film capacitance (1400 nF cm^?2 at 120 nm thickness and 20–100 Hz). Furthermore, it shows pronounced electrical and mechanical self‐healing behavior, can serve as the gate dielectric for organic semiconductors, and can even induce healing of the conductivity of a layer coated above it together with the process of healing itself. Based on these attractive properties, we developed a self‐healable, low‐voltage operable, printed, and flexible OFET for the first time, showing promise for vapor sensing as well as conventional OFET applications.     

Influence of Electric Field on Microstructures of Pentacene Thin‐Films in Field‐Effect Transistors

We report on electric‐field‐induced irreversible structural modifications in pentacene thin films after long‐term operation of organic field‐effect transistor (OFET) devices. Micro‐Raman spectroscopy allows for the analysis of the microstructural modifications of pentacene in the small active channel of OFET during device operation. The results suggest that the herringbone packing of pentacene molecules in a solid film is affected by an external electric field, particularly the source‐to‐drain field that parallels the a–b lattice plane. The analysis of vibrational frequency and Davydov splitting in the Raman spectra reveals a singular behavior suggesting a reduced separation distance between pentacene molecules after long‐term operations and, thus, large intermolecular interactions. These results provide evidence for improved OFET performance after long‐term operation, related to the microstructures of organic semiconductors. It is known that the application of large electric fields alters the semiconductor properties of the material owing to the generation of defects and the trapping of charges. However, we first suggest that large electric fields may alter the molecular geometry and further induce structural phase transitions in the pentacene films. These results provide a basis for understanding the improved electronic properties in test devices after long‐term operations, including enhanced field‐effect mobility, improved on/off current ratio, sharp sub‐threshold swing, and a slower decay rate in the output drain current. In addition, the effects of source‐to‐drain electric field, gate electric field, current and charge carriers, and thermal annealing on the pentacene films during OFET operations are discussed.     

Organic Transistor Based on Cyclopentadithiophene‐Benzothiadiazole Donor–Acceptor Copolymer for the Detection and Discrimination between Multiple Structural Isomers

Distinguishing structural isomers is a critical and challenging task for biotechnology, chemical industry, and environmental monitoring. Approaches currently available are limited in terms of selectivity and simplicity. In this paper, a highly sensitive organic field‐effect transistor (OFET) using the cyclopentadithiophene‐benzothiadiazole (CDT‐BTZ) copolymers as a semiconductor is presented for easy and selective detection of different families of structural isomers, as well as between different isomers within each family. High accuracy discrimination is achieved over a range of concentrations using only a single sensing parameter derived from the OFET characteristic transfer curve. As a reference, other homopolymer‐ and donor–acceptor copolymer‐based OFET sensors are examined but do not have an equivalent sensing performance to that of the CDT‐BTZ‐based OFETs. Investigating the link between isomer absorption and swelling, supramolecular order and energy levels of the active layer reveals a unique effect of each isomer on the energy bands of the semiconducting polymer.     

Control of Polymorphism and Morphology in Solution Sheared Organic Field‐Effect Transistors

During the last decades, small molecule organic semiconductors have been successfully used as active layer in organic field‐effect transistors (OFETs). Despite the high mobility achieved so far with organic molecules, in order to progress in the field it is crucial to find techniques to process them from solution. The device reproducibility is one of the principal weak points of organic electronics for further commercialization. To achieve a high device‐to‐device reproducibility it is essential to control the morphology and polymorphism of the active layer for OFET application. In this work, the preparation of thin films is reported based on blends of the organic semiconductor dibenzo‐tetrathiafulvalene (DB‐TTF) and polystyrene by a solution shearing technique compatible with upscaling. Here, it is demonstrated that varying the deposition parameters (i.e., speed and temperature) or the solution formulation (i.e., semiconductor/binder polymer ratio) is possible to control the film morphology and semiconductor polymorphism and, hence, the different intermolecular interactions. It is demonstrated that the control of the thermodynamics and kinetics of the crystallization process is key for the device performance optimization. Further, this is the first time that DB‐TTF thin films of the α‐polymorph are reported.     

n‐Channel,Ambipolar, and p‐Channel Organic Heterojunction Transistors Fabricated with Various Film Morphologies

The relationship between the performance characteristics of organic field‐effect transistors (OFETs) with 2,5‐bis(4‐biphenylyl)bithiophene/copper hexadecafluorophthalocyanine (BP2T/F₁₆CuPc) heterojunctions and the thickness of the BP2T bottom layer is investigated. Three operating modes (n‐channel, ambipolar, and p‐channel) are obtained by varying the thickness of the organic semiconductor layer. The changes in operating mode are attributable to the morphology of the film and the heterojunction effect, which also leads to an evolution of the field‐effect mobility with increasing film thickness. In BP2T/F₁₆CuPc heterojunctions the mobile charge carriers accumulate at both sides of the heterojunction interface, with an accumulation layer thickness of ca. 10 nm. High field‐effect mobility values can be achieved in continuous and flat films that exhibit the heterojunction effect.     

Inkjet‐Printed Organic Electrodes for Bottom‐Contact Organic Field‐Effect Transistors

A graphite thin film was investigated as the drain and source electrodes for bottom‐contact organic field‐effect transistors (BC OFETs). Highly conducting electrodes (10² S cm^?1) at room temperature were obtained from pyrolyzed poly(l,3,4‐oxadiazole) (PPOD) thin films that were prepatterned with a low‐cost inkjet printing method. Compared to the devices with traditional Au electrodes, the BC OFETs showed rather high performances when using these source/drain electrodes without any further modification. Being based on a graphite‐like material these electrodes possess excellent compatibility and proper energy matching with both p‐ and n‐type organic semiconductors, which results in an improved electrode/organic‐layer contact and homogeneous morphology of the organic semiconductors in the conducting channel, and finally a significant reduction of the contact resistance and enhancement of the charge‐carrier mobility of the devices is displayed. This work demonstrates that with the advantages of low‐cost, high‐performance, and printability, PPOD could serve as an excellent electrode material for BC OFETs.     

Air Effect on the Ideality of p‐Type Organic Field‐Effect Transistors: A Double‐Edged Sword

Organic field‐effect transistors (OFETs) often deviate from ideal behaviors in air, which masks their intrinsic properties and thus significantly impedes their practical applications. A key issue of how the presence of air affects the ideality of OFETs has not yet been fully understood. It is revealed that air atmosphere may exert a double‐edged sword effect on the active semiconductor layer when determining the ideality of OFETs fabricated from p‐type crystalline organic semiconductors. Upon exposing the as‐fabricated device to air, water and oxygen mainly function as efficient p‐type dopants for the active layer in the contact regions, enhancing charge carrier injection and consequently improving device ideality. Nevertheless, as the exposure time increases, the trapping centers for the injected minority charge carriers appear in the channel region, leading to degradation of device ideality. Inspired by the double‐edged sword behavior of air, a near‐ideal OFET is achieved by ingeniously utilizing the doping/positive effect and eliminating the trapping/negative effect. The effect of air on the ideality of p‐type OFETs is clarified, which not only illuminates some common observations of OFETs in air but also offers useful guidance for the construction of high‐performance ideal OFETs.