Fabrication and magnetic properties of Sm3(Fe,Ti)29Nx/α-Fe dual-phase nanocomposite permanent magnetic material

Sm3(Fe,Ti)29Nx/α-Fe dual-phase nanometer magnetic material was fabricated through rapid solidification, crystallization and nitridation of Sm-Fe (Ti) alloy. The effect of combination of rapid solidification and Ti alloy addition on the phase formation and microstructure of the Sm-Fe alloy is investigated in this paper. The microstructure of amorphous phase and dual-phase nano-grain crystals before and after crystallization annealing were observed using a high-resolution transmission electron microscope (HREM). The dual-phase nano-grains after annealing were compacted together with a clear interface with the direct exchange-coupling mechanism. Different annealing processes were used to examine the melt-spun alloy. Comparison of the images of SEM showed that annealing at 750℃ for 10 min was most suitable to get homogeneous and nano-grains. No obvious kink was detected in the second quadrant of the hysteresis loop like a single hard magnet, and strong exchange coupling was found between hard magnets and soft magnets.     

Synthesis ofNanocrystalline RuO2（60%）-SnO2（40%） Powders by Amorphous Citrate Route

Nanometer RuO2-SnO2 was synthesized by the citrate-gel method using RuCl3, SnCl4 as cation sources, citric acid as complexing agent and anhydrous ethanol as solvent. The structures of the derived powders were characterized by thermogravimetric and differential thermal analysis, X-ray diffraction, transmission electron microscope, and Brunauer-Emmett-Teller surface area measurement. The pure, fine and amorphous powders was obtained at 160℃. The materials calcined at above 400 ℃ were composed of rutile-type oxide phases having particle sizes of fairly narrow distribution and good thermal resistant properties. By adding SnO2 to RuO2, the Ru metallic phase can be effectively controlled under a traditional temperature of preparation for dimensional stable anode.     

Study on H atoms diffusion and adsorption properties of MgH<Subscript>2</Subscript>-V systems

Based on experimental results that VH_0.81/MgH₂ interface was found during the process of mechanically milling MgH₂+5at.%V nanocomposite, H atoms diffusion and adsorption properties of MgH₂-V systems have been investigated by using a first-principles plane-wave pseudopotential method based on the density functional theory. The results are as follows. When VH/MgH₂ interface is formed due to V alloying MgH₂ phase, the vacancy formed by H atoms near VH phase region is more stable than that without V alloying, while vacancy near MgH₂ phase region is less stable than that without V alloying. During the process of H atoms diffusion after V alloying, the max migration barrier energy of H atoms in MgH₂-V systems is reduced compared with that of MgH₂ phase, which means that H atoms diffuse easily. When H diffuses into VH from MgH₂ across VH/MgH₂ interface, among three substitutions such as the replacement of H for V vacancy, or interstitial site or V atoms, the replacement of H for V vacancy has the strongest diffusion ability, next interstitial site, and finally V atoms site. As far as H adsorbed on different surfaces of VH phase is concerned, physical adsorption is carried out more easily than chemical adsorption, and the behavior of H atoms adsorbed on the surface near VH phase region can be found more easily than that near MgH₂ phase region. Supported by the Ministry of Science and Technology of China (Grant No. 2006CB605104) and the National Natural Science Foundation of China (Grant No. 50771044)     

Pool boiling on the superhydrophilic surface with TiO<Subscript>2</Subscript> nanotube arrays

Surface with TiO₂ nanotube arrays (TNTAs) is superhydrophilic and of great specific area. This paper investigates the pool boiling characteristics at the thermal interface with TNTAs. The results show that the TNTAs interface can enhance the pool boiling heat transfer compared to the pure Ti metal plate. The bubbles formed at the initial nucleation state are very small and released in higher frequency. The pool boiling heat transfer enhancement at the TNTAs interface may be attributed to the high density of nucleate site, high intrinsic heating area of nanotubes layer, superhydrophilicity and the vertically oriented nanotube structure. Supported by the National Natural Science Foundation of China (Grant No. 50846069)     

The influence of mo additive on the microstructure and property of Ti/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> composite

The influence of Mo on the microstructure, bending strength and HV of Ti/Al₂O₃ composite was studied, and the influence mechanism was analyzed. The results indicate that after the addition of Mo, the composite organization is finer and phases distribution is better-proportioned which make the microstructure denser, the bending strength and HV of composite are also increased to a degree. But the bending strength increases first then decreases with the increasing of Mo content, so the appropriate Mo content for the Ti/Al₂O₃ composite is to be further confirmed. WANG Zhi: Born in 1962 Funded by Natural Science Foundation of China (No. 50232020) and Natural Science Foundation of Shandong Province (No. 2002F21)     

Thermoelectric Properties and Electronic Structure of Ca3Co2O6

The nanosized Ca3Co2O6 powder was synthesized via sol-gel process.The phase composition was characterized by means of X-ray diffraction.Polycfrystalline swnples of Ca3Co2O6 were prepared by a sintering procedure of nanosized power.The seebeck cofficient and electrical conductivity of the samples were measured from 450K up to 750 K.The results show that the Seebeck coefficient increases with the increasing temperature.The electronic structures were calculated using the self-cwtsistent full-potential linearized augmentedc plane-wave (LAPW) method within the density functional theory.The relationship between thermoelectric property and electronic structures was discussed.     

Cu<Subscript>2</Subscript>ZnSnS<Subscript>4</Subscript> thin films prepared by sulfurizing different multilayer metal precursors

Cu₂ZnSnS₄ (CZTS) thin films were successfully fabricated on glass substrates by sulfurizing Cu-Sn-Zn multilayer precursors, which were deposited by ion beam sputtering and RF magnetron sputtering, respectively. The structural, electrical and optical properties of the prepared films under various processing conditions were investigated in detail. Results showed that the as-deposited CZTS thin films with the precursors by both ion beam sputtering and RF magnetron sputtering have a composition near stoichiometric. The crystallization of the samples, however, has a strong dependence on the atomic percent of constituents of the prepared CZTS films. A single phase stannite-type structure CZTS with a large absorption coefficient of 10₄/cm in the visible range could be obtained after sulfurization at 520°C for 2 h. The samples relative to the RF magnetron sputtering showed a low resistivity of 0.073 Ωcm and band gap energy of about 1.53 eV. The samples relative to the ion beam sputtering exhibited a resistivity of 0.36 Ωcm and the band gap energy is about 1.51 eV. Supported by the National Natural Science Foundation of China (Grant No. 10574106), the Planned Science and Technology Project of Guangdong Province (Grant No.2003C05005) and the Natural Science Fund of Zhanjiang Normal University (Grant No.200801)     

Synthesis and structure of NaNbO<Subscript>3</Subscript> ceramic powders in ultrahigh pressure field

The NaNbO3 powders were synthesized and their crystal structure changes were analyzed by ultrahigh pressure up to 6 GPa. The results indicate that the pure NaNbO3 powders can be synthesized at 300℃ under a pressure of 4 GPa, to significantly restrain the Na element volatilization compared with the traditional synthesis method. It is found that the crystal structure of synthesized NaNbO3 changes from low symmetry to high symmetry with the increase of the pressure.     

Composite cathode Bi<Subscript>1.14</Subscript>Sr<Subscript>0.43</Subscript>O<Subscript>2.14</Subscript>-Ag for intermediate-temperature solid oxide fuel cells

Composites consisting of strontium stabilized bismuth oxide （Bi1.14Sr0.43O2.14, SSB） and silver were investigated as cathodes for intermediate-temperature solid oxide fuel cells with doped ceria electrolyte. There were no chemical reactions between the two components. The microstructure of the interfaces between composite cathodes and Ce0.8Sm0.2O1.9 （SDC） electrolytes was examined by scanning electron microscopy （SEM）. Impedance spectroscopy measurements show that the performance of cathode fired at 700 ℃ is the best. When the content of Ag2O is 70 wt%, polarization resistance values for the SSB-Ag cathodes are as low as 0.2 Ωcm^2 at 700℃ and 0.29 Ωcm^2 at 650℃. These results are much smaller than some of other reported composite cathodes on doped ceria electrolyte and indicate that SSB-Ag composite is a potential cathode material for intermediate temperature SOFCs.     

Sensing characterization of Sn/In/Ti nanocomplex oxides for CO,CH<Subscript>4</Subscript> and NO<Subscript>2</Subscript>

The nanocomplex oxides of Sn-In and Sn-In-Ti were prepared by controlled co-precipitation method as sensing materials of semiconductor gas sensors for detection of CO, CH4 and NO2. Through manipulating the Sn/In cation ratio, metal salt total concentration, precipitation pH value and aging time, the nanocrystalline powders were successfully derived with chemical homogeneity and superior thermal stability, compared with the single component oxides. The particle size and morphology, surface area, and thermal and phase stabilities were characterized using TEM, TG-DTA, BET and XRD. The sensing tests showed that the Sn-In composites exhibit high sensitivity and selectivity for CO and NO2. The introduction of TiO2 enhanced CH4 sensitivity and selectivity, particularly, additives of Pd and Al2O3 as a dopant and surface modification greatly enhanced the sensing properties. The sensitivity depended on the composition of composites, calcination temperature and operating temperature. The optimal values were (25%In2O3- 75%SnO2)-20%TiO2 for ternary composite, 600 and 300℃, respectively. Temperature-programmed desorption (TPD) studies were employed to explain the gas adsorption behavior displayed by the surface of nanocomposites and X-ray photoelectron spectroscopic (XPS) analysis was used to confirm the electronic interactions existing between oxide components. The sensing mechanism of the nanocomposites was attributed to chemical and electronic synergistic effects.     

Fabrication and Characterization of Nano- CaCO3/Polypropylene Foam Sheets

By applying the reinforcing and toughening effect of calcium carbonate （CaCO3） nanoparticles on polypropylene, foam sheets of good performance were successfully fabricated by extrusion. The equipment and conditions of the extrusion were explored. The mechanical properties of the produced foam sheets were tested. The effect of CaCO3 nano-particles on the mechanical properties and the cellular structure of the sheets was comprehensively studied. The experimental results show that the optimum content of CaCO3 nano-particles in the composite material was -4wt%. At this content, the nano-particles were well dispersed in the substrate, and the composite material had maximum tensile strength and impact strength. Surface treatment of the nano-particles only affected the impact strength of the composite material. CaCO3 micro-particles, on the other hand, showed little effect on the properties of the composite material when the micro-particles content was less than 5 wt%. At a content higher than 5wt%, the properties of the composite material significantly worsened.     

Crystallization of Fe78Si6B13 Bulk Crystaline/Amorphous （c/a） Composite

A metallic crystalline/amorphous （c/a） bulk composite was prepared by the slow cooling method after remelting the amorphous Fe78Si9B13 ribbon. By X-ray diffraction （XRD）, differential scanning calorimetry （DSC） and scanning electron microscope （SEM）, the composite consists of the primary dendrite α-Ee （without Si） as well as the amorphous matrix. After being anneal at 800 K, the uniform spheroid particles are formed in the c/a composite, which does not form in the amorphous ribbon under the various annealing process. Energy dispersive analysis of X-rays （EDAX）, SEM and XRD were applied to give more detailed information. The formation and evolution of the particle may stimulate the possible application of the Fe-matrix amorphous alloy.     

Synthesis of Ti3SiC2/TiB2 Composite by In-situ Hot Pressing （HP） Method

Ti3SiC2/TiB2 composite was successfully obtained by hot pressing Ti/TiC/Si/B4C power mixtures.Volume fraction of TiB2 in Ti3SiC2/TiB2 composite can not exceed 10%.Incorporation of excessive TiB2 will affect the reactions process.TiC and Ti5Si3 were two important intermediate phases during the whole reactions.The microstructure characteristics of the Ti3SiC2/TiB2 composites were analyzed using scanning electron microscopy （SEM） and transmission electron microscopy （TEM）.The experimental results show that the grains of Ti3SiC2/TiB2 composite are structured in a layered form,and the formation of TiB2 particles as reinforcements with elongated or equiaxed shape distributes in Ti3SiC2 matrix.     

Photocatalytic performance of TiO<Subscript>2</Subscript> thin films connected with Cu micro-grid

Aiming at reducing the recombination of photo-induced carriers in semiconductor photocatalytic process, we prepared TiO₂ thin film with its surface modified by a connected Cu micro-grid via a microsphere lithography strategy, which showed higher photocatalytic activity than the pure TiO₂ film. The improvement of photocatalytic activity of Cu micro-grid to the TiO₂ film is due to the charge carrier separation and electron transfer by the conducting metal grid. The photocatalytic activity was improved as metal loading increased, which obtained the best performance at a certain loading amount, and then decreased at higher loading amount. This phenomenon was attributed to the metal’s bulk effect which could be explained by the relationship between the energetic positions and the metal cluster size. Supported by the National Natural Science Foundation of China (Grant Nos. 50672003, 50872005) and the National Basic Research Program of China (“973” Project) (Grant No. 2007CB613302) and the Fok Ying Tong Education Foundation (Grant No. 111050)     

Preparation and characterization of nanocomposite MgFe<Subscript>2</Subscript>O<Subscript>4</Subscript>/SiO<Subscript>2</Subscript>

Nanocomposites MgFe₂O₄/SiO₂ were successfully synthesized by the sol-gel method in the presence of N, N-dimethylformamide (DMF). The formation of pure MgFe₂O₄ was confirmed by powder X-ray diffraction (XRD) and electron diffraction. The structural evolution of MgFe₂O₄ nanocrystals was followed by powder X-ray diffraction and IR absorption spectroscopy. The formation of spinel structure of MgFe₂O₄ started at 800 °C, and completed at 900 °C. The transmission electron microscopy (TEM) measurements suggest that the particle sizes increase with the increasing annealing temperature, and the mean particle sizes of the spherical samples annealed at 800 °C, 900 °C and 1 050 °C are ca. 3 nm, 8 nm and 11 nm, respectively. Magnetization measurements at room temperature and 78 K indicate superparamagnetic nature of these MgFe₂O₄ nanocrystals. Funded by the National Natural Science Foundation of China(No. 30771676), the Natural Science Foundation of Jiangsu Province (No. BK20081842), and the Foundation of Nanjing Bureau of Personal for the Returned Overseas Chinese Excellent Scholars     

Structure and properties of Mg-doped SrBi<Subscript>4</Subscript>Ti<Subscript>4</Subscript>O<Subscript>15</Subscript> Bi-layered compounds

The structure and properties of Mg-doped SrBi4Ti4O15（SBT） were dicussed. Mg substitution into SBT had two possibilities states with the dopant amount variety. Mg cation substituted mostly into Sr^2＋ and the amount proportion was 68.11%.Mg ion will substitute into Ti ion site in perovskite layer when the doping amount increases. Polarization increases sharply when x=0.1 and then decreases becauses of the domain pinning. The Curie temperature of Mg-doped SBT is about 300 ℃ and there is a broad diffuse phase transition near Tc with a flat peak near the Ta of SBT.     

Thermal-dynamical properties and pressure dependence of phonon spectrum of ordered Si<Subscript>50</Subscript>Ge<Subscript>50</Subscript> alloy based on <Emphasis Type="Italic">ab initio</Emphasis> methods

The phonon spectrum of ordered zincblende Si₅₀Ge₅₀ alloy is calculated by ab initio method. The energy band structure at zero pressure and the pressure dependence of phonon dispersion curves are shown up to 20 GPa. The calculation finds a pressure-induced softening of the transverse acoustic phonon mode and the mode frequency reaching zero at about 14 GPa, which indicate breaking of the symmetry and formation of a new phase under high pressure. Supported by the National Natural Science Foundation of China (Grant No. 50771090), the State Key Program for Basic Research of China (Grant No. 2005CB724404) and the Program for Changjiang Scholars and Innovative Team (Grant No. IRT0650)     

The film-forming behavior on the interface between air and hydrosol of Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> nanoparticles

The film forming behavior on the interface between air and hydrosol of Fe₂O₃ nanoparticles was investigated by the surface pressure-time isotherms, the surface pressure-trough area isotherms, Brewster angle microscopy and transmission electron microscopy. It is found that the freshly prepared hydrosol of Fe₂O₃ nanoparticles is not stable. The surface pressure increases with the aging time and finally approaches a constant, and the smaller the concentration is, the smaller the surface pressure is stabilized at and the shorter the time the hydrosol reaching stable needs. The surface pressure also increases with compression until collapsed, and the longer the hydrosol is aged, the higher the collapsing pressure is. A uniform and compact film composed of nanoparticles with an average diameter of about 2–3 nm on the air-hydrosol interface is observed by Brewster angle microscope and transmission electron microscope. Funded by the National Natural Science Foundation of China (50672089), the Encouraging Foundation for the Scientific Research of the Excellent Young and Middleaged Scientists in Shandong Province(2006BS04034)     

Investigation of one-dimensional Si/SiO<Subscript>2</Subscript> hotonic crystals for thermophotovoltaic filter

The spectral control is widely incorporated with the thermophotovoltaic (TPV) technology to improve the optical-electric conversion efficiency of the whole system. In order to match with GaSb photovoltaic cell, an 8-layer one-dimensional photonic crystals (PC) filter structure was designed as quarter-wave periodic structure by selecting silicon (Si) and silicon dioxide (SiO₂) as candidate materials. The multilayer Si/SiO₂ structure was developed for the matching filter to simultaneously realize the optimal matching with the spectral distribution of the high temperature emitter and the quantum efficiency of GaSb cell. The physical vapor deposition (PVD) method was used to fabricate the optical filter and the normal incidence optical property of the filter was measured within the spectral range from 0.7 to 3.3 μm. These experimental data were used to predict the spectral control performance in a TPV system. Finally, temperature performance experiments were carried out to establish its withstanding performance in high temperature environment. Supported by the National Natural Science Foundation of China (Grant No. 50776047) and Natural Science Foundation of Jiangsu Province (Grant No. BK2007726)     

Tensile properties of an aluminum matrix composite reinforced by SnO<Subscript>2</Subscript>-coated Al<Subscript>18</Subscript>B<Subscript>4</Subscript>O<Subscript>33</Subscript> whisker

Al18B4O33 whisker was coated by SnO2 particles using a chemical precipitation method, and an aluminum matrix composite reinforced by the coated whisker was fabricated by squeeze casting technique. It is found that the SnO2 coating can react with aluminum matrix during squeeze casting process, and Sn particles are induced near the interface between Al18B4O33 whisker and matrix. The tensile test at room temperature indicated that the tensile strength of Al18B4O33 whisker reinforced aluminum matrix composite can be enhanced by suitable content of SnO2 coating. The composites with various whisker coating contents exhibit maximum tensile plasticity at about 300 ℃, and the composite with a suitable whisker coating content could enhance its tensile plasticity evidently, which suggest that an Al18B4O33 whisker-Al composite with both high strength at room temperature and high formability at elevated temperature can be designed.