GSM公共信道中SCH自适应均衡解调算法研究

针对移动信道多径效应造成的严重的码间干扰(ISI)问题,研究了基于最大似然序列估计(MLSE)的GSM公共信道中SCH自适应均衡解调算法,并对这种自适应均衡解调算法在Jakes移动信道模型环境下的性能进行了分析和计算机仿真,仿真结果表明该自适应均衡解调算法能够很好地克服码间干扰(ISI)问题,性能良好。     

无人飞行器通信中联合信道估计和Turbo均衡

Turbo均衡技术能有效克服信道多径、消除符号间干扰(ISI),从而提高接收机整体性能。针对无人飞行器地空视距链路信道这种快时变多径信道,提出了一种联合信道估计和Turbo均衡的迭代接收算法。该算法采用单载波调制体制,通过信道估计和Turbo均衡之间相互反馈软信息来消除ISI。Matlab仿真结果表明,经过2次以上的迭代后,相比较于传统的单载波频域Turbo均衡算法,新算法的误码率性能得到了显著改善。     

通用滤波多载波通信系统中干扰抑制均衡算法

作为5G多载波技术强有力的候选对象,通用滤波多载波利用子带滤波技术抑制带外功率泄露,进而降低同步要求和获得更高的频谱效率。本文首先针对通用滤波多载波在慢时变多径信道下的性能进行了分析和研究;其次为消除多径信道所带来的干扰,提出了适用于该多载波系统的信道估计方案,该方案设计了具有重复样式的导频结构进行信道估计,复杂度低;最后针对通用滤波多载波在多径信道下容易遭受符号间干扰的问题,提出了基于干扰消除的Zero-Forcing均衡算法和基于迭代干扰消除的均衡算法,两种算法均能够在消除ISI的基础上进一步地消除ICI和IBI。仿真结果表明,本文提出的信道估计和均衡算法能有效消除通用滤波多载波技术在多径信道下所经受的ISI、ICI和IBI。      

基于Turbo均衡和信道估计的单通道盲信号恢复算法

定时同步是单通道盲信号接收端处理的难点,提出了一种无需定时同步基于Turbo均衡的单通道盲信号恢复算法。该算法将定时同步偏差等效为符号间干扰（ISI,inter-symbol interference）信道,通过信道估计和Turbo均衡相互反馈软信息来改善源信号信息恢复性能。重点研究了初始盲均衡算法、信道估计算法、混合信号的MMSE均衡算法以及三者间的软信息交互。算法复杂度低、计算量小,适用于高阶调制信号。仿真结果表明,对BPSK、QPSK和8PSK信号,该算法都能得到较好的性能,且对等功率和不等功率信号同样适用。     

一种利用信源冗余的Turbo均衡新算法

为克服无线衰落信道中严重的符号间干扰(ISI)的影响,提出了一种新的利用信源冗余的Turbo均衡算法。该算法将联合信源信道译码技术与Turbo均衡技术结合起来,在均衡、译码、信源之间建立起软信息交互的环路,有效提高了整体接收的性能。外信息传递(EXIT)图分析与计算机仿真均表明,尽管信源冗余给译码器带来的性能提升较为有限,但是将这部分信息反馈回均衡器后,在严重ISI信道,信源冗余度为70%时,整体接收的性能改善约为9.5 dB,基本达到了理想加性高斯白噪声（AWGN）信道下的误码性能。     

基于隐训练序列的信道阶数估计研究

在无线通信中,由于信道特性而引起的码间干扰（ISI）是影响通信质量的一个主要因素。抵消ISI的基本方法就是对接收到的数据进行均衡,均衡前进行准确的信道估计非常重要。给出一种在此信息传输系统下基于隐训练序列的信道阶数的估计方法,并对其进行了仿真分析。仿真结果显示,通过对原发送信息序列进行了帧实际数据零均值处理,达到了比较准确的信道阶数估计效果。     

适用于紫外光通信的延迟判决均衡算法

为了消除紫外光通信过程中强烈散射所引起的码间干扰，采用一种带信道估计的最小均方误差-最大似然估计(LMS-MLE)延迟判决均衡算法进行了理论分析和仿真验证。通过选取合适的判决延迟深度来调整LMS自适应滤波器抽头系数进行信道跟踪，获取新的信道估计向量，最后利用MLE均衡算法得到最优序列输出。结果表明, 该算法可以明显提升紫外光通信系统的性能，在没有提高复杂度的情况下，性能接近最优MLE均衡算法，并且可以实现信道跟踪, 紫外光通信中算法的最佳延迟量取值为20。这一结果对紫外光通信性能提升以及MLE均衡器的工程实现是有帮助的。     

用于盲接收的turbo均衡与迭代信道估计

Turbo均衡是一种将信道均衡和差错控制译码联合迭代处理的均衡机制,与传统的均衡器相比,能在更低的信噪比条件下克服严重信道失真导致的符号间干扰(ISI)。该文提出一种用于盲接收的turbo均衡和迭代信道估计方案,不依赖于训练序列或发送符号的先验知识,采用初始盲均衡处理来启动迭代信道估计和turbo均衡。在该方案中,初始盲均衡算法的选择是十分关键的,它需要在恶劣的信道条件为后续迭代处理的启动提供足够的先验信息。该文根据turbo均衡的特点,选择了超指数算法作为初始盲均衡。仿真结果表明,该文提出的用于盲接收的turbo均衡方案是有效的。     

频选MIMO信道下低复杂度PDA SIC算法

为了同时消除频率选择性MIMO系统中的天线间干扰（MAD和码间干扰（ISI），本文将基于信道矩阵QR分解的串行干扰消除（SIC）算法和概率数据辅助（PDA）均衡算法相结合，提出了一种低复杂度的软判决迭代均衡算法。该算法一方面很好地消除了MAI，另一方面将传统PDA算法中大量的矩阵运算简化为数值计算，降低了系统的计算复杂度，并获得了良好的性能。     

一种利用信源冗余的Turbo均衡新算法

为克服无线衰落信道中严重的符号间干扰( ISI)的影响,提出了一种新的利用信源冗余的Turbo均衡算法。该算法将联合信源信道译码技术与Turbo均衡技术结合起来,在均衡、译码、信源之间建立起软信息交互的环路,有效提高了整体接收的性能。外信息传递( EXIT)图分析与计算机仿真均表明,尽管信源冗余给译码器带来的性能提升较为有限,但是将这部分信息反馈回均衡器后,在严重ISI信道,信源冗余度为70%时,整体接收的性能改善约为9.5 dB,基本达到了理想加性高斯白噪声( AWGN)信道下的误码性能。     

Resolution Enhancement Technology:Integrated Process Solutions using OPC

DUV lithography, using the 248 nm wavelength, is a viable manufacturing option for devices with features at 130 nm and less. Given the low kl value of the lithography, integrated process development is a necessary method for achieving acceptable process latitude. The application of assist features for rule based OPC requires the simultaneous optimization of the mask, illumination optics and the resist.Described in this paper are the details involved in optimizing each of these aspects for line and space imaging.A reference pitch is first chosen to determine how the optics will be set. The ideal sigma setting is determined by a simple geometrically derived expression. The inner and outer machine settings are determined, in turn,with the simulation of a figure of merit. The maximum value of the response surface of this FOM occurs at the optimal sigma settings. Experimental confirmation of this is shown in the paper.Assist features are used to modify the aerial image of the more isolated images on the mask. The effect that the diffraction of the scattering bars (SBs) has on the image intensity distribution is explained. Rules for determining the size and placement of SBs are also given.Resist is optimized for use with off-axis illumination and assist features. A general explanation of the material' s effect is discussed along with the affect on the through-pitch bias. The paper culminates with the showing of the lithographic results from the fully optimized system.     

Cost-effective test solutions for smart card and other integrated flash applications

From its emergence in the late 1980s as a lower cost alternative to early EEPROM technologies, flash memory has evolved to higher densities and speedsand rapidly growing acceptance in mobile applications.In the process, flash memory devices have placed increased test requirements on manufacturers. Today, as flash device test grows in importance in China, manufacturers face growing pressure for reduced cost-oftest, increased throughput and greater return on investment for test equipment. At the same time, the move to integrated flash packages for contactless smart card applications adds a significant further challenge to manufacturers seeking rapid, low-cost test.     

Theoretical analysis of the relationship between the Brillouin gain coefficient and the strain in the optical-fiber sensors

The relation between the power of the Brillouin signal and the strain is one of the bases of the distributed fiber sensors of temperature and strain. The coefficient of the Bfillouin gain can be changed by the temperature and the strain that will affect the power of the Brillouin scattering. The relation between the change of the Brillouin gain coefficient and the strain is thought to be linear by many researchers. However, it is not always linear based on the theoretical analysis and numerical simulation. Therefore, errors will be caused if the relation between the change of the Brillouin gain coefficient and the strain is regarded as to be linear approximately for measuring the temperature and the strain. For this reason, the influence of the parameters on the Brillouin gain coefficient is proposed through theoretical analysis and numerical simulation.     

An improved parallel thinning algorithm with two subiterations

The parallel thinning algorithm with two subiterations is improved in this paper. By analyzing the notions of connected components and passes, a conclusion is drawn that the number of passes and the number of eight-connected components are equal. Then the expression of the number of eight-connected components is obtained which replaces the old one in the algorithm. And a reserving condition is proposed by experiments, which alleviates the excess deletion where a diagonal line and a beeline intersect. The experimental results demonstrate that the thinned curve is almost located in the middle of the original curve connectivelv with single pixel width and the processing speed is high.     

Novel fiber-optical interferometer with miniaturized probe for in-hole measurements

Today, micro-system technology and the development of new MEMS （Micro-Electro-Mechanical Systems） are emerging rapidly. In order for this development to become a success in the long run, measurement systems have to ensure product quality. Most often, MEMS have to be tested by means of functionality or destructive tests. One reason for this is that there are no suitable systems or sensing probes available which can be used for the measurement of quasi inaccessible features like small holes or cavities. We present a measurement system that could be used for these kinds of measurements. The system combines a fiber optical, miniaturized sensing probe with low-coherence interferometry, so that absolute distance measurements with nanometer accuracy are possible.     

Development of the readout system for waveguide multilayer optical card

Waveguide multilayer optical card （WMOC） is a novel storage device of three-dimensional optical information. An advanced readout system fitting for the WMOC is introduced in this paper. The hardware mainly consists of the light source for reading, WMOC, motorized stages addressing unit, microscope imaging unit, CCD detecting unit and PC controlling ＆ processing unit. The movement of the precision motorized stage is controlled by the computer through Visual Basic （VB） language in software. A control panel is also designed to get the layer address and the page address through which the position of the motorized stages can be changed. The WMOC readout system is easy to manage and the readout result is directly displayed on computer monitor.     

Study of waveguide coupling efficiency in hybrid silicon lasers

This paper presents a new method to increase the waveguide coupling efficiency in hybrid silicon lasers. We find that the propagation constant of the InGaAsP emitting layer can be equal to that of the Si resonant layer through improving the design size of the InP waveguide. The coupling power achieves 42% of the total power in the hybrid lasers when the thickness of the bonding layer is 100 nm. Our result is very close to 50% of the total power reported by Intel when the thickness of the thin bonding layer is less than 5 nm. Therefore, our invariable coupling power technique is simpler than Intel＇s.     

Collinear phase-matching study of terahertz-wave generation via difference frequency mixed in GaAs and Inp

The collinearly phase-matching condition of terahertz-wave generation via difference frequency mixed in GaAs and InP is theoretically studied. In collinear phase-matching, the optimum phase-matching wave hands of these two crystals are calculated. The optimum phase-matching wave bands in GaAs and lnP are 0.95-1.38μm and 0.7-0.96μm respectively. The influence of the wavelength choice of the pump wave on the coherent length in THz-wave tuning is also discussed. The influence of the temperature alteration on the phase-matching and the temperature tuning properties in GaAs crystal are calculated and analyzed. It can serve for the following experiments as a theoretical evidence and a reference as well.     

Effects of the alloy compositions on the phonon-polaritons in ternary mixed crystals

Composition dependence of bulk and surface phonon-polaritons in ternary mixed crystals are studied in the framework of the modified random-element-isodisplacement model and the Bom-Huang approximation. The numerical results for Several Ⅱ - Ⅵ and Ⅲ- Ⅴ compound systems are performed, and the polariton frequencies as functions of the compositions for ternary mixed crystals AlxGa1-xAs, GaPxAS1-x, ZnSxSe1-x, GaAsxSb1-x, GaxIn1-xP, and ZnxCd1-xS as examples are given and discussed. The results show that the dependence of the energies of two branches of bulk phonon-polaritons which have phonon-like characteristics, and surface phonon-polaritons on the compositions of ternary mixed crystals are nonlinear and different from those of the corresponding binary systems.     

New insert layer structure OLEDs

An insert layer structure organic electroluminescent device（OLED） based on a new luminescent material （Zn（salen）） is fabricated. The configuration of the device is ITO/CuPc/NPD/Zn（salen）/Liq/LiF/A1/CuPc/NPD/Zn（salen）/Liq/LiF/A1. Effective insert electrode layers comprising LiF（1nm）/Al（5 nm） are used as a single semitransparent mirror, and bilayer cathode LiF（1 nm）/A1（100 nm） is used as a reflecting mirror. The two mirrors form a Fabry-Perot microcavity and two emissive units. The maximum brightness and luminous efficiency reach 674 cd/m^2 and 2.652 cd/A, respectively, which are 2.1 and 3.7 times higher than the conventional device, respectively. The superior brightness and luminous efficiency over conventional single-unit devices are attributed to microcavity effect.