Effectiveness factor of fast (Fe3+/Fe2+), moderate (Cl2/Cl?) and slow (O2/H2O) redox couples using IrO2-based electrodes of different loading

The effectiveness factor, E _f, (fraction of the electrode surface that participates effectively in the investigated reaction) of fast (Fe³⁺/Fe²⁺), moderate (Cl₂/Cl⁻) and slow (O₂/H₂O) redox couples has been estimated using IrO₂-based electrodes with different loading. The method of choice was linear sweep voltammetry (measurement of the anodic peak current) for the Fe³⁺/Fe²⁺ redox couple and steady-state polarization (determination of the exchange current) for the O₂ and Cl₂ evolution reactions. The results have shown that the effectiveness factor depends strongly on the kinetics of the investigated redox reaction. For the Fe³⁺/Fe²⁺ redox couple, effectiveness factors close to zero (max 4%) have been obtained contrary to the O₂ evolution reaction where effectiveness factors close to 100% can be achieved, all being independent of IrO₂ loading. For the Cl₂ evolution reaction, intermediate values of the effectiveness factor have been found and they decrease strongly, from 100% down to about 60%, with increasing loading.     

Investigation of formic acid oxidation on Ti/IrO2 electrodes

A model has been proposed according to which the voltammetric charge involved in the Ti/IrO₂ electrodes is due to two contributions: a faradaic contribution due to surface redox activities at the IrO₂ coating and a non-faradaic contribution due to the charging of electrical double layer (). The later has been proposed as a tool for the estimation of the relative surface area of the Ti/IrO₂ electrodes.Differential electrochemical mass spectrometry (DEMS) measurements using H₂¹⁸O has demonstrated that we are dealing with an active electrode in which the surface redox couple IrO₃/IrO₂ acts as mediator in the oxidation of formic acid (FA).From the voltammetric measurements using different IrO₂ loading and FA concentrations, the kinetic parameters of FA oxidation via the surface redox couple IrO₃/IrO₂ have been determined.Finally a model has been proposed considering that FA oxidation at Ti/IrO₂ anodes is controlled by mass transfer. The good agreement between the experimental results and the model indicates that the surface reaction between FA and the electrogenerated IrO₃ is a fast reaction.     

Electrochemical oxidation of ammonia (NH4/NH3) on thermally and electrochemically prepared IrO2 electrodes

The electrochemical oxidation of ammonia (NH₄⁺/NH₃) in sodium perchlorate was investigated on IrO₂ electrodes prepared by two techniques: the thermal decomposition of H₂IrCl₆ precursor and the anodic oxidation of metallic iridium. The electrochemical behaviour of Ir(IV)/Ir(III) surface redox couple differs between the electrodes indicating that on the anodic iridium oxide film (AIROF) both, the surface and the interior of the electrode are electrochemically active whereas on the thermally decomposed iridium oxide films (TDIROF), mainly the electrode surface participates in the electrochemical processes.On both electrodes, ammonia is oxidized in the potential region of Ir(V)/Ir(IV) surface redox couple activity, thus, may involve Ir(V). During ammonia oxidation, TDIROF is deactivated, probably by adsorbed products of ammonia oxidation. To regenerate TDIROF, it is necessary to polarize the electrode in the hydrogen evolution region. On the contrary, AIROF seems not to be blocked during ammonia oxidation indicating its fast regeneration during the potential scan. The difference between both electrodes results from the difference in the activity of the iridium oxide surface redox couples.     

Influence of rare earths doping on the structure and electro-catalytic performance of Ti/Sb-SnO2 electrodes

Rare earth Ce, Eu, Gd and Dy doped Ti/Sb-SnO₂ electrodes were prepared by thermal decomposition and the performance of electrodes for the electro-catalytic decomposition of a model pollutant (phenol) was investigated. Phenol degradation and TOC removal followed pseudo-first-order kinetics in the experimental range, with the maximum rate achieved using Gd-doped electrode and the minimum rate obtained by Ce-doped electrode. Electrodes were characterized by cyclic voltammetry, X-ray diffraction, electron dispersive spectrometry, and X-ray photoelectron spectroscopy. It was suggested that the enhanced performance of the Gd-doped Ti/Sb-SnO₂ electrode arose from the increased adsorption capacity of hydroxyl radicals on the electrode surface and the lower mobility of oxygen atoms in SnO₂ lattice. The redox couple of Ce⁴⁺/Ce³⁺ on Ce-doped Ti/Sb-SnO₂ electrode surface functioned as mediators in the electrochemical oxidation process, allowing oxygen transfer in the SnO₂ lattice, and lowered the electro-catalytic ability of the electrode on phenol mineralization.     

Electrocatalytic oxidation of coal on Ti-supported metal oxides coupled with liquid catalysts for H2 production

Electrocatalytic oxidation of coal on Ti-supported metal/metal oxides coupled with liquid catalysts is systematically investigated as a method of producing hydrogen at the cathode. The composition of the liquid catalyst was varied to determine its effect on the coal electrolysis. A spectrum of byproducts from the coal oxidation at the anode was analyzed. The Ti-supported metal oxide electrodes were prepared by thermal decomposition and characterized by scanning electron microscopy (SEM). X-ray diffraction results show that the composition of the electrodes was Ti/Pt, Ti/RuO₂, Ti/IrO₂ and Ti/IrO₂–RuO₂. Coal oxidation tests on these electrodes indicate that Ti/IrO₂ has the best electrocatalytic activity. Polarization curves reveal that redox catalysts, such as Fe³⁺, K₃Fe(CN)₆, KBr and V₂O₅, bridge the coal particles and the solid electrode surface, thus increasing the rates of coal oxidation. The dynamic transition of Fe³⁺/Fe²⁺ is proven by a KMnO₄ titration experiment, and the possible catalytic mechanism is discussed. Product analysis shows that pure H₂ is generated at the cathode and that CO₂ is the main product at the anode.     

Synergistic effects of doped Fe3+ and deposited Au on improving the photocatalytic activity of TiO2

Fe³⁺ doped together with Au deposited TiO₂ (Au/Fe³⁺–TiO₂) was successfully prepared, which shows excellent photocatalytic activity for degradation of methyl orange (MO) under both UV and visible light (λ > 420 nm) illumination. Fe³⁺ has been confirmed by EPR to substitute for Ti⁴⁺ in the TiO₂ lattice, and Au exists as Au⁰ on the surface of the photocatalyst indicated by the results of XRD. Fe³⁺ and Au have synergistic effects on improving the photocatalytic activity of TiO₂. A proposed mechanism concerning the synergistic effects is discussed to explain the improvement of the photocatalytic activities.     

Kinetic study of formic acid oxidation on Ti/IrO2 electrodes prepared using the spin coating deposition technique

In the first part of this paper, IrO₂ electrodes produced by thermal decomposition of H₂IrCl₆ precursor were manufactured using the spin coating deposition technique, where centrifugal forces spread the precursor solution with simultaneous evaporation of the solvent on the rotating Ti substrate. It was found using this technique, that it is possible to obtain thin and uniform IrO₂ coatings with controlled loadings. The influence of the concentration of iridium salt in the precursor solution (c₀) as well as the influence of the rotation speed at which the substrate spins (ω) on the IrO₂ loading have been studied using voltammetric charge measurements. From these results, a simple relation has been proposed for the estimation of the IrO₂ loading for a given c₀ and ω.In the second part of this paper and from measurements performed using different IrO₂ loadings and formic acid concentrations, the kinetic parameters of the oxidation of formic acid have been quantitatively determined using a model that involves the redox couple IrO₃/IrO₂ as mediator of this reaction. Furthermore, using the kinetic parameters obtained together with the Nernst equation and the I-V curves of the supporting electrolyte (1 M HClO₄), theoretical I-V curves could be constructed for different concentrations of formic acid and different IrO₂ loadings.     

A comparative study on IrO2-Ta2O5 coated titanium electrodes prepared with different methods

The electrodes of IrO₂-Ta₂O₅ coated titanium were prepared using conventionally thermal decomposition procedure and polymer sol-gel (Pechini) method, respectively. The microstructure and electrochemical properties of the electrodes were studied with scanning electron microscope (SEM), energy dispersive X-ray (EDX), atomic force microscope (AFM), potentiodynamic polarization, cyclic voltammetry, electrochemical impedance spectroscopy and accelerated life test. As compared with the electrode formed using the traditional method of thermal decomposition, the oxide electrode prepared by Pechini method presents morphology of higher nano-scale roughness and more uniform surface composition with little precipitates. It also has larger electrochemically active surface area, better electrocatalytic activity for oxygen evolution and higher stability.     

Functionalized magnetic core-shell Fe3O4@SiO2 nanoparticles as selectivity-enhanced chemosensor for Hg(II)

A colorimetric and ‘‘turn-on” fluorescent chemosensor Rho-Fe₃O₄@SiO₂ for Hg²⁺ in which N-(rhodamine-6G)lactam-ethylenediamine (Rho-en) is conjugated with the magnetic core-shell Fe₃O₄@SiO₂ NPs has been strategically designed and synthesized. The final product was characterized by X-ray power diffraction (XRD), transmission electron microscopy (TEM), Fourier transform infrared spectra (FTIR) and UV-visible absorption and fluorescence emission. Fluorescence and UV-visible spectra results showed that the resultant multifunctional nanoparticles Rho-Fe₃O₄@SiO₂ exhibited selective ‘turn-on’ type fluorescent enhancements and distinct color changes with Hg²⁺. The selectivity of the Rho-Fe₃O₄@SiO₂ for Hg(II) ion is better than that of the Rho-en in the same conditions. In addition, the presence of magnetic Fe₃O₄ nanoparticles in the sensor Rho-Fe₃O₄@SiO₂ NPs would also facilitate the magnetic separation of the Hg(II)-Rho-Fe₃O₄@SiO₂ from the solution.     

Influence of precursor Bi/Fe ion concentration on hydrothermal synthesis of BiFeO3 crystallites

In this study we investigated the effect of precursor Bi³⁺/Fe³⁺ ion concentration on the hydrothermal synthesis of BiFeO₃ crystallites. It is demonstrated that the phase-purity and morphology of the products is highly dependent on the metal ion concentration. Phase-pure BiFeO₃ crystals can be prepared at the Bi³⁺/Fe³⁺ ion concentration ranging from 0.025 to 0.0625 M. The samples prepared at n(Bi³⁺/Fe³⁺)=0.025, 0.0375, 0.05, and 0.0625 M, are composed, respectively, of cuboid-like particles (100–200 nm), regular spherical agglomerates (30–40 μm) made up of irregular grains with size about several hundred nanometers, irregular flower-like clusters formed from irregular grains of several hundred nanometers in size, and octahedron-shaped particles (500–600 nm). These samples have a similar bandgap energy of 2.20 eV and exhibit a typical antiferromagnetic behavior at room temperature.     

Structure and electrochemical performance of nanostructured Fe3O4/carbon nanotube composites as anodes for lithium ion batteries

Polyvinyl alcohol (PVA) was used as a hydrogen bond functionalizing agent to modify multi-walled carbon nanotubes (CNTs). Nanoparticles of Fe₃O₄ were then formed along the sidewalls of the as-modified CNTs by the chemical coprecipitation of Fe²⁺ and Fe³⁺ in the presence of CNTs in an alkaline solution. The structure and electrochemical performance of the Fe₃O₄/CNTs nanocomposite electrodes have been investigated in detail. Electrochemical tests indicated that at the 145th cycle, the CNTs-66.7 wt.%Fe₃O₄ nanocomposite electrode can deliver a high discharge capacity of 656 mAh g⁻¹ and stable cyclic retention. The improvement of reversible capacity and cyclic performance of the Fe₃O₄/CNTs nanocomposite could be attributed to the nanosized Fe₃O₄ particles and the network of CNTs.     

Nanocomposite Fe2O3-Se as a new lithium storage material

The electrochemical properties of nanocomposite Fe₂O₃-Se thin film prepared by pulsed laser deposition (PLD) method have been investigated by cyclic voltammetry and charge/discharge measurements. A large reversible capacity of nanocomposite Fe₂O₃-Se thin film was found to be around 650 mAh g⁻¹. A new couple of reduction and oxidation peaks at 1.4 and 1.8 V were observed from cyclic voltammogram for the first time. Our data demonstrated that nanocomposite Fe₂O₃-Se exhibit larger capacity and better cycle performance than pure Fe₂O₃. The electrochemical reaction mechanisms of Fe₂O₃-Se with lithium were examined by X-ray photoelectron spectroscopy (XPS), high resolution transmission electron microscopy (HRTEM) and selected-area electron diffraction (SAED). The reversible conversions reaction of nanosized metal Fe with Li₂Se and Li₂O formed after initial discharge process into FeSe and Fe₂O₃ respectively were revealed.     

Voltammetric study of interaction of Co(phen)3 with DNA at gold nanoparticle self-assembly electrode

Modifying electrode surfaces on the molecule scale allow developing new electrochemical biosensors. A new strategy for the immobilization of calf thymus DNA on the surface of gold nanoparticles which are co-immobilized at a gold electrode through 4,4^′-bis(methanethiol) biphenyl (MTP) molecule by assembly process is demonstrated. The DNA modified electrode was incubated in Co(phen)₃³⁺ solution of an aqueous buffer or an acetonitrile (AN) solution, then it was rinsed and placed in a Co(phen)₃³⁺ free buffer solution or AN solution, followed by cyclic voltammetric experiments. Clear redox peaks of Co(phen)₃³⁺ were observed both in an aqueous and AN solutions. The concentration of supporting electrolyte on electrochemical behavior was discussed. It was found that the surface coverage value of DNA molecules on modified gold nanoparticle and the redox current of adsorbed Co(phen)₃³⁺ were decrease with increasing the size of gold nanoparticles (6, 25, 42, 73, and 93 nm). In aqueous solution, the electron transfer rate constant of Co(phen)₃^3+/2+ redox couple became slow with increasing the diameter of gold nanoparticle, and the speed almost had nothing to do with the diameter in nonaqueous solution. The surface concentration of Co(phen)₃³⁺ adsorption on DNA modified electrode decreased and rate constant of adsorption kinetics increased with increasing the interactive temperature. In AN solution, the electrostatic interaction between DNA and Co(phen)₃^3+/2+ was greatly reduced, however, compare with in aqueous solution the interaction between DNA and reduced form of Co(phen)₃²⁺ was more strongly than oxidized form Co(phen)₃³⁺. The surface concentration of Co(phen)₃³⁺ adsorption on DNA modified electrode reach maximum value when the interactive temperature about 20 °C, and rate constant of adsorption kinetics nearly independent of the interactive temperature. The results show that the DNA can adsorb on the modified electrode firmly and the Co(phen)₃^3+/2+ adsorbed on DNA give good electrochemical response both in aqueous and nonaqueous solutions. It was confirmed that the DNA modified electrode can be applied in a nonaqueous system and the modified electrode can be used to investigate the interaction between DNA and electroactive species both in aqueous and nonaqueous systems.     

Luminescent properties of a novel afterglow phosphor Sr3Al2O5Cl2:Eu,Ce

A series of Eu²⁺ and Ce³⁺ doped/co-doped Sr₃Al₂O₅Cl₂ afterglow phosphors that presented various bright colors were successfully synthesized via high temperature solid state reaction. The structure and luminescence properties of the obtained samples were characterized by X-ray powder diffraction (XRD), photoluminescence (PL) spectra and decay curves as well as the thermoluminescence (TL) glow curves. The XRD results showed that all the phase could be indexed to the orthorhombic structure with the space group P2₁2₁2₁. After being exposed to a 254 nm or 365 nm mercury lamp, blue/yellow-orange afterglow emissions with broad bands peaking around 620 nm/435 nm, which were ascribed to the characteristic 4f⁶5d–4f⁷/5d¹–4f¹ transitions of Eu²⁺/Ce³⁺, could be observed in phosphors of Sr₃Al₂O₅Cl₂:Eu²⁺/Sr₃Al₂O₅Cl₂:Ce³⁺, respectively. Because of the overlap spectral range between the Sr₃Al₂O₅Cl₂:Eu²⁺ and Sr₃Al₂O₅Cl₂:Ce³⁺ phosphors, the energy transfer (ET) from Ce³⁺ to Eu²⁺ occurred. The related ET process was discussed in detail. Moreover, the incorporation of Ce³⁺ could significantly prolong the afterglow duration of Sr₃Al₂O₅Cl₂:Eu²⁺ phosphor, which was due to the increase of trap concentration. Consequently, 6 h of the afterglow duration could be observed in Sr₃Al₂O₅Cl₂:1.0%Eu²⁺, 0.5%Ce³⁺ sample, exhibiting much longer than that of Sr₃Al₂O₅Cl₂: 1.0%Eu²⁺ (3 h). From the afterglow decay curves and the fitting results, the optimal concentration of Ce³⁺ for the enhanced afterglow property was experimentally determined to be 0.5%.     

Multifuctional Fe3O4@C/YVO4:Dy nanopowers: Preparation,luminescence and magnetic properties

As-synthesized Fe₃O₄ nanoparticles were encapsulated with carbon layers through a simple hydrothermal process. Fe₃O₄/C nanoparticles were coated with YVO₄:Dy³⁺ phosphors to form bifunctional Fe₃O₄@C@YVO₄:Dy³⁺ composites. Their structure, luminescence and magnetic properties were characterized by XRD, SEM, TEM, HRTEM, PL spectra and VSM. The experimental results indicated that the as-prepared bifunctional composites displayed well-defined core–shell structures. The ∼12 nm diameter YVO₄:Dy³⁺ shell exhibited tetragonal structure. Additionally, the composites exhibited a high saturation magnetization (13 emu/g) and excellent luminescence properties, indicating their promising potential as multifunctional biosensors for biomedical applications.     

A delithiated LiNi0.65Co0.25Mn0.10O2 electrode material: A structural, magnetic and electrochemical study

A crystalline LiNi_0.65Co_0.25Mn_0.10O₂ electrode material was synthesized by the combustion method at 900 °C for 1 h. Rietveld refinement shows less than 3% of Li/Ni disorder in the structure. Lithium extraction involves only the Ni²⁺/Ni⁴⁺ redox couple while Co³⁺ and Mn⁴⁺ remain electrochemically inactive. No structural transition was detected during cycling in the whole composition range 0 < x < 1.0. Furthermore, the hexagonal cell volume changes by only 3% when all lithium was removed indicating a good mechanical stability of the studied compound. LiNi_0.65Co_0.25Mn_0.10O₂ has a discharge capacity of 150 mAh/g in the voltage range 2.5-4.5 V, but the best electrochemical performance was obtained with an upper cut-off potential of 4.3 V. Magnetic measurements reveal competing antiferromagnetic and ferromagnetic interactions - varying in strength as a function of lithium content - yielding a low temperature magnetically frustrated state. The evolution of the magnetic properties with lithium content confirms the preferential oxidation of Ni ions compared to Co³⁺ and Mn⁴⁺ during the delithiation process.     

A novel kojic acid amperometric sensor based on hollow CuO/Fe2O3 hybrid microspheres immobilized in chitosan matrix

Hollow CuO/Fe₂O₃ hybrid microspheres with small uniform holes were synthesized using a convenient hydrothermal method and were applied to fabricated an amperometric sensor for kojic acid. The resulting materials were characterized by scanning electron microscopy (SEM) and X-ray diffraction (XRD) and then were immobilized into the chitosan (Chi) matrix onto a glassy carbon electrode to obtain CuO/Fe₂O₃–Chi/GCE. The potential utility of the constructed electrodes were demonstrated by applying them to the analytical determination of kojic acid concentration. The electrochemical behavior of kojic acid on CuO/Fe₂O₃–Chi/GCE was explored. The modified electrode displayed excellent amperometric response for kojic acid with a linear range from 0.2 μM to 674 μM with a detection limit of 0.08 μM at a signal-to-noise ratio of 3. In order to validate feasibility, the CuO/Fe₂O₃–Chi/GCE has been used for quantitative detecting kojic acid in real samples.     

Electrochemical activity, stability and degradation characteristics of IrO2-based electrodes in aqueous solutions containing C1 compounds

In this paper, we investigate the electrocatalytic behavior and degradation characteristics of IrO₂-based electrodes in Na₂SO₄ solutions containing C₁ compounds (CH₃OH, HCHO and HCOOH). Decreases are generally observed in the electrochemically active area, electrochemical stability and durability of the electrodes in aqueous solutions in the presence of these organic substrates. The following sequence holds for the influence of C₁ compounds on the electrode properties (i.e. activity and stability): CH₃OH > HCHO > HCOOH. The corrosion characteristics of electrode are studied by X-ray diffraction measurements. For the first time, the decomposition and dissolution of active oxide layers are quantitatively characterized from the decreases in cell volume of rutile-structured IrO₂ crystallite and from the increases in texture coefficient of (0 0 2) planes, respectively, as a result of the accelerated lifetime tests.     

Electrochemical characterization of amorphous LiFe(WO4)2 thin films as positive electrodes for rechargeable lithium batteries

Amorphous LiFe(WO₄)₂ thin films have been fabricated by radio-frequency (R.F.) sputtering deposition at room temperature. The as-deposited and electrochemically cycled thin films are, respectively, characterized by X-ray diffraction, scanning electron microscopy, transmission electron microscopy, selected area electron diffraction, and X-ray photoelectron spectra techniques. An initial discharge capacity of 198 mAh/g in Li/LiFe(WO₄)₂ cells is obtained, and the electrochemical behavior is mostly preserved in the following cycling. These results identified the electrochemical reactivity of two redox couples, Fe³⁺/Fe²⁺ and W⁶⁺/W^x+ (x = 4 or 5). The kinetic parameters and chemical diffusion coefficients of Li intercalation/deintercalation are estimated by cyclic voltammetry and alternate-current (AC) impedance measurements. All-solid-state thin film lithium batteries with Li/LiPON/LiFe(WO₄)₂ layers are fabricated and show high capacity of 104 μAh/cm² μm in the first discharge. As-deposited LiFe(WO₄)₂ thin film is expected to be a promising positive electrode material for future rechargeable thin film batteries due to its large volumetric rate capacity, low-temperature fabrication and good electrode/electrolyte interface.     

Characterization of surface fouling of Ti/IrO2 electrodes in 4-chlorophenol aqueous solutions by electrochemical impedance spectroscopy

Electrochemical impedance spectroscopy (EIS) was used as the main technique coupled with cycling voltammetry (CV) to characterize the surface fouling of a conventional Ti/IrO₂ in 4-CP aqueous solutions caused by the electropolymerization of chlorinated phenol. Capacitive information of polymeric films formed was successfully derived from both the on-line and off-line impedance measurements and was used to characterize the surface fouling of IrO₂ electrodes. Results showed that the fouling extent at IrO₂ electrode decreased when its heating temperature was increased. With increasing the anodic potential, the surface fouling was enhanced firstly and then weakened, reaching the highest extent at 0.9 V. More positive potentials were believed to further oxidize the formed films and thereby to reactivate the deactivated electrode surface. With the increase of positive potential, the regeneration was enhanced, but no entire recovering could be achieved after the reactivation even at very high potentials.