共查询到20条相似文献,搜索用时 93 毫秒
1.
2.
报道了一种简单结构的超宽带ASE光纤光源,采用两个相同的980 nm半导体激光器对同一段掺铒光纤进行抽运,通过选择合适的掺铒光纤长度及调节两个抽运源的抽运功率,获得了带宽大于80 nm、输出功率21 mW的C L波段的ASE荧光输出。 相似文献
3.
超宽带ASE光纤光源研究 总被引:1,自引:0,他引:1
报道了一种简单结构的超宽带ASE光纤光源,采用两个相同的980nm半导体激光器对同一段掺铒光纤进行抽运,通过选择合适的掺铒光纤长度及调节两个抽运源的抽运功率,获得了带宽大于80nm、输出功率21mW的C L波段的ASE荧光输出。 相似文献
4.
5.
6.
为了得到一种高性能的C+L波段的宽带掺铒光纤光源,用一个980nm和一个1480nm激光二极管作为抽运源,用两个3dB宽带耦合器作为光纤反射镜,同时利用功率控制电路让光源输出光稳定,对设计的光源进行了实验和理论验证,获得了功率为168.67mW(22.27dBm)、带宽达到80.701nm(1525.112nm~1605.813nm)的C+L波段宽带光源。结果表明,开始用两个980nm和一个1480nm二极管作为抽运源,之后改为一个980nm和一个1480nm二极管作为抽运源,并没有减少光源的输出功率,也没有改变稳定性。这一结果对减少光源的成本、提高光光转换效率,具有实际价值。 相似文献
7.
优化设计了高功率、高效率掺铒光纤超荧光光源的参数。采用商用掺铒光纤,针对双程后向结构,首先仿真了光源输出功率和带宽随掺铒光纤长度的变化,并用对等实验验证了模拟结果,初步确定掺铒光纤长度的优化范围;理论研究了反射镜反射率对光源性能的影响,计算出最佳反射率并模拟了该反射率下光源的输出光谱;实验研究了抽运功率对光源平均波长的影响,确定了优化的抽运功率范围,并进一步确定了掺铒光纤的优化长度。实验选用110mW抽运功率,13.74m掺铒光纤,获得了输出功率为46.9mW的高功率光纤光源,其抽运转换效率可达42.6%,且光源保持了约34.54nm的宽带宽。 相似文献
8.
一种双抽运结构C+L波段掺铒光纤宽带光源 总被引:1,自引:0,他引:1
介绍了一种结构简单、工作在C+L波段掺铒宽带光源。实验中用3dB宽带耦合器作为光纤反射镜,同时利用功率控制电路让光源输出光稳定,先用两个980nm二极管作为抽运源,将后向的C波段ASE重新引回光纤中,提高了抽运源的利用效率和光纤输出光的稳定性,优化掺铒光纤长度,获得了功率高达26.67mW(14.26dBm)的C+L波段ASE光输出,平均波长1550.887nm。之后采用一个980nm和一个1480nm的激光二极管,在输出相对平坦的情况下,得到了最高功率为23.23mW(13.66dBm),平均波长为1556.46nm的C+L波段ASE光输出,光纤环形镜的使用,不仅改善了光源的平坦度,并且大大提高了光光转化效率。 相似文献
9.
10.
一种新颖的反射结构高功率超宽带光纤光源 总被引:12,自引:1,他引:12
报道了一种新型高功率超宽带光纤光源。利用980nm激光二极管(LD)和1480nmLD双向抽运掺铒光纤,经光纤环镜反射后,得到C L波段自发辐射谱。通过调整980nmLD和1480nmLD的功率,在1524.O~1600.6nm(76.6nm)范围内,自发辐射谱功率高于-18.8dBm,并且在1539.2~l600.6nm(61.4nm)范围内,自发辐射谱的平坦度为2.8dB。总荧光功率为22.1mW。转换效率为18.8%。如果不加环镜,并且保持相同的抽运条件,得到的放大自发辐射(ASE)谱宽在1525~1565nm的C波段范围,其总的荧光功率为7.1mW,转换效率仅为6%。通过分析加环镜情况与不加环镜情况下所得到的自发辐射谱,以及加环镜情况下采用不同的抽运方式得到的自发辐射谱,最终得出结论,通过加环镜,并且用980nmLD和1480nmLD双向抽运,得到了具有最佳效果的超宽带光纤光源。实验过程中通过调整980nmLD和1480nmLD的功率,曾得到28.5mW的荧光功率,转换效率为22.3%。 相似文献
11.
12.
环形腔掺铒光纤激光器的实验研究 总被引:3,自引:0,他引:3
利用掺饵光纤和环形腔结构,在980nm半导体激光器泵浦下,获得了1.56μm波长的光纤激光器输出。激光器的阈值泵浦功率为5.2mW。具有很好的线性输出特性。 相似文献
13.
10 kHz-linewidth diode-pumped Er:Yb:glass laser 总被引:1,自引:0,他引:1
A single-mode Er:Yb:phosphate glass laser pumped at 980 nm by an InGaAs diode laser is reported. The laser emits over 15 mW output power with 6% slope efficiency. The measured linewidth is 10.6 kHz and the RIN power is less than 140 dB/Hz.<> 相似文献
14.
Time-dependent modeling of erbium-doped waveguide lasers in lithiumniobate pumped at 980 and 1480 nm
We have developed a rigorous phenomenological model for analyzing rare-earth doped waveguide lasers. The model is based on time-dependent laser rate equations for an arbitrary rare-earth-doped laser host with multiple energy levels. The rate equations are coupled with the laser signal and pump photon flux equations that have time-dependent boundary conditions. The formulation results in a large and stiff set of transcendental and coupled differential equations that are solved using finite difference discretization and the method of lines. Solutions for the laser signal power, pump power, and populations of ion energy levels as functions of space and time are obtained for waveguide lasers. We have used the model to predict the CW characteristics and Q-switched performance of waveguide lasers in lithium niobate pumped by a 980-nm source. Our analysis shows that hole burning can occur in erbium-doped lithium niobate lasers because of the intensity variation across guided transverse modes. We have predicted that Q-switch pulse peak powers can exceed 1 kW with pulsewidths less than 1 ns. Moreover, we have compared the CW and Q-switched performance of 980-nm pumped waveguide lasers and 1480 nm pumped waveguide lasers. An analysis of the effects of host- and fabrication-dependent parameters on CW 980-nm pumped lasers is included. These parameters include cooperative upconversion, excited state absorption, doping concentration, excess waveguide loss, cavity length, and mirror reflectance values. We demonstrate good quantitative agreement with waveguide laser experimental data obtained in our laboratory and with results from the literature 相似文献
15.
16.
The authors report a 1.96 μm doubly resonant optical parametric oscillator using bulk periodically poled LiNbO3 directly pumped by a commercial 980 nm CW diode laser 相似文献
17.
18.
本文设计了用Mach-Zehnder干涉型调制开关作为调Q开关的掺铒铌酸锂(Er:LiNbO3)调Q波导激光器,并进行分析。发现激光器输出功率可达1.5kW以上;比较了泵浦光波长为980nm和1480nm时的输出功率和脉冲宽度的情况,研究了腔长变化对激光器输出特性的影响,发现用1480nm光泵浦时阈值较低,但用980nm光泵浦能得到更高的峰值功率和更窄的脉冲宽度。 相似文献
19.
单频分布布拉格反射光纤激光器及温度传感实验研究 总被引:2,自引:1,他引:1
报道利用Er∶Yb双掺杂光纤制作的单频窄线宽分布布拉格反射 (DBR)光纤激光器。在 980nm半导体激光器抽运下 ,当抽运功率为 75mW时 ,获得了输出功率为 2 3mW的单频激光 ,其中心波长为 1 5 5 7 5 2 4nm ,线宽小于 5MHz。利用制作的单频DBR光纤激光器构成光纤有源传感系统 ,进行温度传感实验研究 ,实验结果线性度很好 ,高信噪比和高输出功率使得该系统具有波长易于检测的优点 相似文献
20.
Efficient operation of a Yb/sup 3+/-doped silica-fibre laser at 980 nm is reported. When pumped with a dye laser at 890 nm, and with a symmetrical cavity, a lasing threshold of 17 mW launched power and a single-ended slope efficiency of nearly 40% against launched pump power has been achieved.<> 相似文献