低温多效海水淡化混流效组系统优化与分析

建立了多个混流点的混流效组低温多效蒸发(LT-MED)海水淡化数学优化模型,将海水视为盐和水的混合物,其焓表达为温度的函数,降低优化模型的非线性程度,使其易于收敛。以比传热面积为优化目标分析了不同流程和参数对系统的影响。结果表明,在喷淋密度为30~80 g/(m·s)时,多混流点系统的造水比与单混流点系统相比提高了12.1%,比传热面积降低了8.4%,优化流程为5效+2效+2效组合;提高首效加热蒸汽温度可有效的减少换热面积,降低制水成本,对系统的造水比影响不大;增加系统效数,可以有效提高造水比。各效等面积蒸发方案造水比比不等面积方案略有下降,比传热面积略有增加。模拟结果与文献中相关数据吻合良好,可为低温多效蒸发海水淡化系统工程化设计提供技术支持。     

万吨级低温多效蒸发海水淡化能量及经济性能模拟分析

通过VC++编制了海水淡化的模拟工艺程序,模拟分析了蒸发器总效数、首效蒸发器温度、末效蒸发器温度、浓缩比等因素对低温多效蒸发海水淡化工艺的能耗和技术经济的影响,为海水淡化系统的设计和运行提供了参考依据.     

低温多效蒸发海水淡化系统热力分析

建立了喷射器低温多效蒸发海水淡化系统的数学模型,计算分析了各种温度损失随温度的变化,并研究了顶值盐水温度、蒸发器效数和动力蒸汽等参数对系统的造水比和生产单位质量淡水所需传热面积的影响。结果表明各种温度损失在末效蒸发器内显著增加;喷射器低温多效蒸发系统的热力特性明显优于多效蒸发系统;通过增加顶值盐水温度、蒸发器效数和动力蒸汽温度,可以实现系统的优化运行。     

多相流蒸发法高浓缩率海水淡化系统的热力学性能分析

建立了顺流进料的多相流蒸发法高浓缩率海水淡化系统的数学模型,考虑了热力损失、压力损失、盐水含量变化引起的温差损失;计算分析了相同淡水产量下固体颗粒体积分数、预热量、首效加热蒸汽温度对系统的影响。结果表明,固体颗粒体积分数和首效加热蒸汽温度对各效蒸发器传热面积影响较大;预热量对生蒸汽耗量影响较大;固体颗粒的加入能够强化传热,减小各效蒸发器的传热面积;在无预热情况下,固体颗粒体积分数为13%时,蒸发器总传热系数比固体颗粒体积分数为3%时可增大6.71%,各效蒸发器传热面积减少4.97%,淡水成本减少1.22%。     

低温多效压汽蒸馏海水淡化系统热力分析

低温多效压汽蒸馏(LT-METVC)海水淡化是一种很有发展前途的海水淡化方法,文中首先探讨了海水淡化系统中盐水焓、熵、的计算方法,然后对典型LT-METVC流程进行了详细的热力学分析,包括重要参数对系统性能的影响规律和系统的利用。结果表明:驱动蒸汽压力升高,会使造水比增加、效率下降,比传热面积则基本不变;系统效数增加或压缩比降低,都会使系统造水比和效率提高、比传热面积增大。LT-METVC系统的效率很低,在示例中仅为1.3%。提出并初步讨论了进一步改善性能的途径。     

船用海水淡化机性能分析

建立了低温单效船用小型海水淡化机的工艺性能计算模型,并进行了性能模拟计算和分析.在产量一定的条件下,考察了热源温度、蒸发温度、海水进料温度、传热系数与造水成本的关系,对系统的经济性能作出了初步分析.     

不同流程下低温多效海水淡化系统热力性能研究

建立了串联无预热、串联预热、并联无预热、并联预热4种流程下的低温多效海水淡化系统数学模型,并利用MATLAB语言编制程序进行了求解,比较了不同流程对系统热力性能的影响。计算结果表明：当海水淡化系统为6效,在其他参数相同的情况下,与无预热流程相比,预热流程所需的加热蒸汽量较少,造水比较大,传热总面积较小,冷却海水量小。与串联流程相比,并联流程所需的加热蒸汽量较少,造水比较大,传热总面积较小,冷却海水量小。综合结果是并联预热流程的热力性能最优。     

大型低温多效蒸发海水淡化装置传热过程热力损失分析

基于低温多效蒸发海水淡化装置的各种阻力和海水沸点升高(BPE)关联式,计算了海水淡化装置中流动阻力、海水沸点升高等造成的传热过程热力损失,分析了各项热力损失在各效蒸发/冷凝器中的分布、随蒸发/冷凝器数量的变化规律等。结果表明:产水量、浓缩比和加热蒸汽温度等参数均保持不变的前提下,总的热力损失随着装置的蒸发/冷凝器数量而增加;BPE引起的热力损失占最大比例,但流动阻力引起的热力损失不可忽略。通过对海水淡化装置热力损失的分析,提出了低温多效蒸发海水淡化装置"小温差、低流阻、饱和态、高敏感"的工作特征理论。     

大型低温多效蒸发海水淡化装置传热过程热力损失分析

基于低温多效蒸发海水淡化装置的各种阻力和海水沸点升高（BPE） 关联式,计算了海水淡化装置中流动阻力、海水沸点升高等造成的传热过程热力损失,分析了各项热力损失在各效蒸发/冷凝器中的分布、随蒸发/冷凝器数量的变化规律等。结果表明：产水量、浓缩比和加热蒸汽温度等参数均保持不变的前提下,总的热力损失随着装置的蒸发/冷凝器数量而增加;BPE引起的热力损失占最大比例,但流动阻力引起的热力损失不可忽略。通过对海水淡化装置热力损失的分析,提出了低温多效蒸发海水淡化装置“小温差、低流阻、饱和态、高敏感”的工作特征理论。     

高浓缩倍率低温多效蒸馏海水淡化阻垢研究

模拟低温多效蒸馏装置水平管降膜蒸发条件,进行海水淡化高浓缩倍率条件下阻垢技术研究。实验利用滴定法和原子吸收分光光度计法,考察了不同操作条件下钙镁等易结垢离子浓度变化,并对形成的垢样收集处理后进行场发射扫描电子显微镜及能谱仪测试分析,得到垢物晶型形貌及其元素组成。结果表明:在蒸发温度40—80℃,盐水质量分数5%—8%(质量分数),阻垢剂添加量0—8 mg/L条件范围内,钙离子损失率随着蒸发温度和盐水质量分数的升高而增加,随着阻垢剂添加量的增大而减小。过程产生的垢主要成分为碳酸钙,另有少量氢氧化镁和硫酸钙。在提高海水浓缩倍率条件下,低温多效蒸馏装置结垢趋势更明显,可通过添加适量阻垢剂和定期药剂清洗来控制。     

Insect antifeedant properties of anthranoids from the genusVismia

Vismiones and ferruginins, representatives of a new class of lypophilic anthranoids from the genusVismia were found to inhibit feeding in larvae of species ofSpodoptera, Heliothis, and inLocusta migratoria.     

Direct observation of freeze-thaw instability of latex coatings via high pressure freezing and cryogenic SEM

Despite its industrial importance, the subject of freeze-thaw (F/T) stability of latex coatings has not been studied extensively. There is also a lack of fundamental understanding about the process and the mechanisms through which a coating becomes destabilized. High pressure (2100 bar) freezing fixes the state of water-suspended particles of polymer binder and inorganic pigments without the growth of ice crystals during freezing that produce artifacts in direct imaging scanning electron microscopy (SEM) of fracture surfaces of frozen coatings. We show that by incorporating copolymerizable functional monomers, it is possible to achieve F/T stability in polymer latexes and in low-VOC paints, as judged by the microstructures revealed by the cryogenic SEM technique. Particle coalescence as well as pigment segregation in F/T unstable systems are visualized. In order to achieve F/T stability in paints, latex particles must not flocculate and should provide protection to inorganic pigment and extender particles. Because of the unique capabilities of the cryogenic SEM, we are able to separate the effects of freezing and thawing, and study the influence of the rate of freezing and thawing on F/T stability. Destabilization can be caused by either freezing or thawing. A slow freezing process is more detrimental to F/T stability than a fast freezing process; the latter actually preserves suspension stability during freezing. Presented at the 82nd Annual Meeting of the Federation of Societies for Coatings Technology, October 27–29, 2004 in Chicago, IL. Tied for first place in The John A. Gordon Best Paper Competition.     

Ethanol and (−)-α-Pinene: Attractant Kairomones for Bark and Ambrosia Beetles in the Southeastern US

In 2002–2004, we examined the flight responses of 49 species of native and exotic bark and ambrosia beetles (Coleoptera: Scolytidae and Platypodidae) to traps baited with ethanol and/or (−)-α-pinene in the southeastern US. Eight field trials were conducted in mature pine stands in Alabama, Florida, Georgia, North Carolina, and South Carolina. Funnel traps baited with ethanol lures (release rate, about 0.6 g/day at 25–28°C) were attractive to ten species of ambrosia beetles (Ambrosiodmus tachygraphus, Anisandrus sayi, Dryoxylon onoharaensum, Monarthrum mali, Xyleborinus saxesenii, Xyleborus affinis, Xyleborus ferrugineus, Xylosandrus compactus, Xylosandrus crassiusculus, and Xylosandrus germanus) and two species of bark beetles (Cryptocarenus heveae and Hypothenemus sp.). Traps baited with (−)-α-pinene lures (release rate, 2–6 g/day at 25–28°C) were attractive to five bark beetle species (Dendroctonus terebrans, Hylastes porculus, Hylastes salebrosus, Hylastes tenuis, and Ips grandicollis) and one platypodid ambrosia beetle species (Myoplatypus flavicornis). Ethanol enhanced responses of some species (Xyleborus pubescens, H. porculus, H. salebrosus, H. tenuis, and Pityophthorus cariniceps) to traps baited with (−)-α-pinene in some locations. (−)-α-Pinene interrupted the response of some ambrosia beetle species to traps baited with ethanol, but only the response of D. onoharaensum was interrupted consistently at most locations. Of 23 species of ambrosia beetles captured in our field trials, nine were exotic and accounted for 70–97% of total catches of ambrosia beetles. Our results provide support for the continued use of separate traps baited with ethanol alone and ethanol with (−)-α-pinene to detect and monitor common bark and ambrosia beetles from the southeastern region of the US.     

Methyl 2,4,6-decatrienoates Attract Stink Bugs and Tachinid Parasitoids

Halyomorpha halys (Stål) (Pentatomidae), called the brown marmorated stink bug (BMSB), is a newly invasive species in the eastern USA that is rapidly spreading from the original point of establishment in Allentown, PA. In its native range, the BMSB is reportedly attracted to methyl (E,E,Z)-2,4,6-decatrienoate, the male-produced pheromone of another pentatomid common in eastern Asia, Plautia stali Scott. In North America, Thyanta spp. are the only pentatomids known to produce methyl 2,4,6-decatrienoate [the (E,Z,Z)-isomer] as part of their pheromones. Methyl 2,4,6-decatrienoates were field-tested in Maryland to monitor the spread of the BMSB and to explore the possibility that Thyanta spp. are an alternate host for parasitic tachinid flies that use stink bug pheromones as host-finding kairomones. Here we report the first captures of adult and nymph BMSBs in traps baited with methyl (E,E,Z)-2,4,6-decatrienoate in central Maryland and present data verifying that the tachinid, Euclytia flava (Townsend), exploits methyl (E,Z,Z)-2,4,6-decatrienoate as a kairomone. We also report the unexpected finding that various isomers of methyl 2,4,6-decatrienoate attract Acrosternum hilare (Say), although this bug apparently does not produce methyl decatrienoates. Other stink bugs and tachinids native to North America were also attracted to methyl 2,4,6-decatrienoates. These data indicate there are Heteroptera in North America in addition to Thyanta spp. that probably use methyl 2,4,6-decatrienoates as pheromones. The evidence that some pentatomids exploit the pheromones of other true bugs as kairomones to find food or to congregate as a passive defense against tachinid parasitism is discussed.     

2007～2008年世界塑料工业进展

收集了2007年7月～2008年6月世界塑料工业的相关资料,介绍了2007～2008年国外塑料工业的发展情况,提供了世界塑料产量、消费量及全球各类树脂的需求量及产能情况.按通用热塑性树脂(聚乙烯、聚丙烯、聚苯乙烯、聚氯乙烯、ABS树脂)、工程塑料(尼龙、聚碳酸酯、聚甲醛、热塑性聚酯、聚苯醚)、特种工程塑料(聚苯·硫醚、液晶聚合物、聚醚醚酮)、通用热固性树脂(酚醛、聚氨酯、不饱和聚酯树脂、环氧树脂)不同品种的顺序,对树脂的产量、消费量、供需状况及合成工艺、产品应用开发、树脂品种的延伸及应用的进一步扩展等技术作了详细介绍.     

2005～2006年国外塑料工业进展

收集了2005年7月～2006年6月国外塑料工业的相关资料,介绍了2005—2006年国外塑料工业的发展情况。提供了世界塑料产量、消费量及全球各类树脂生产量以及各国塑料制品的进出口情况。作为对比,介绍了中国塑料的生产情况。按通用热塑性树脂（聚乙烯、聚丙烯、聚苯乙烯、聚氯乙烯、ABS树脂）、工程塑料（聚酰胺、聚碳酸酯、聚甲醛、热塑性聚酯、聚苯醚）、通用热固性树脂（酚醛、聚氨酯、不饱和树脂、环氧树脂）、特种工程塑料（聚苯硫醚、液晶聚合物、聚醚醚酮）的品种顺序,对树脂的产量、消费量、供需状况及合成工艺、产品开发、树脂品种的延伸及应用的扩展作了详细的介绍。