CHARACTERISTICS OF A HORIZONTAL SWIRLING FLOW PNEUMATIC CONVEYING WITH A CURVED PIPE

ABSTRACT

In order to prevent flow blockage phenomenon and to reduce the impact of particles on the wall of the bend, an experimental study of the swirling flow pneumatic conveying system with a horizontal curved pipe was carried out in this work. The experiment was performed in a 90-deg pipe bend with pipe diameter 75 mm and centerline curvature ratio 12. The straight pipes with 75 mm inside diameter at the upstream and downstream of the bend were 1.3 m and 4.0 m in lengths, respectively. The initial swirl number was varied from 0.22 to 0.60, the mean air velocity from 10 to 20 m/s, and the solid mass flow rate from 0.07 to 0.68 kg/s. It is found that in the lower air velocity range, the overall pressure drop of the swirling flow pneumatic conveying shows a lower tendency than that of axial flow pneumatic conveying. The minimum air velocities can be decreased by using the swirling flow pneumatic conveying. From the visualization of particle flow patterns, the impact of particles on the wall of the bend can be reduced using the swirling flow.     

A NUMERICAL SIMULATION OF SWIRLING FLOW PNEUMATIC CONVEYING IN A HORIZONTAL PIPELINE

A numerical simulation for swirling and axial flow pneumatic conveying in a horizontal pipe was carried out with a Eulerian approach for the gas phase and a stochastic Lagrangian approach for particle phase, where particle-particle and particle-wall collisions were taken into consideration. The k-ε turbulence model is used to characterize the time and length scales of the gas-phase turbulence. Models are proposed for predicting the particle source and additional pressure loss. The numerical results are presented for polyethylene pellets of 3.1 mm diameter conveyed through a pipeline of 13 m in length with an inner diameter of 80 mm, solid mass flow rate was 0.084 kg/s, and gas velocity was varied from 10 m/s to 18 m/s. The particle flow patterns, the particle concentration and the particle velocity, and additional pressure loss were obtained. It is found that the particle velocity and concentration has almost same value along flow direction in swirling flow pneumatic conveying. The profile of particle concentration for swirling flow pneumatic conveying exhibits symmetric distribution towards the centerline and the higher particle concentration appears in neighbor of wall in the acceleration region. At downstream, the uniform profile of particle concentration is observed. The particle velocity profile, on the other hand, is uniform for both swirling and axial flow pneumatic conveying. A comparison of the calculations with the measured data shows a good agreement within an average error of less than 15 percent.     

An Experimental Study on Degradation of Maize Starch During Pneumatic Transportation

Although attrition during pneumatic conveying is a common problem, very few publications can be found in the open literature on this subject. The particle-to-wall impact is perhaps the predominant cause of degradation since the particle impinges the wall surface at high velocities in dilute phase pneumatic conveying. The most important factors appear to be the conveying air velocity and moisture content. This article presents the experimental findings of a study on degradation of maize starch during pneumatic conveying process. The tests were carried out in a conveying setup having a pipe length of approximately 50 m and a pipe inner diameter of 50 mm in order to find out the breakage of particles under various airflow velocity conditions and temperatures. Dehumidified air was used during the experimentation, and the air temperatures used during these test were 100°C and 25°C. The experimental results indicated that for a given air temperature condition, the variation of attrition rate was a complex function of air velocity and solids loading ratio. Further, for any start pressure condition, the attrition rate was found to increase substantially with increase in air temperature.     

A NUMERICAL SIMULATION OF SWIRLING FLOW PNEUMATIC CONVEYING IN A HORIZONTAL PIPELINE

ABSTRACT

A numerical simulation for swirling and axial flow pneumatic conveying in a horizontal pipe was carried out with a Eulerian approach for the gas phase and a stochastic Lagrangian approach for particle phase, where particle-particle and particle-wall collisions were taken into consideration. The k-? turbulence model is used to characterize the time and length scales of the gas-phase turbulence. Models are proposed for predicting the particle source and additional pressure loss. The numerical results are presented for polyethylene pellets of 3.1 mm diameter conveyed through a pipeline of 13 m in length with an inner diameter of 80 mm, solid mass flow rate was 0.084 kg/s, and gas velocity was varied from 10 m/s to 18 m/s. The particle flow patterns, the particle concentration and the particle velocity, and additional pressure loss were obtained. It is found that the particle velocity and concentration has almost same value along flow direction in swirling flow pneumatic conveying. The profile of particle concentration for swirling flow pneumatic conveying exhibits symmetric distribution towards the centerline and the higher particle concentration appears in neighbor of wall in the acceleration region. At downstream, the uniform profile of particle concentration is observed. The particle velocity profile, on the other hand, is uniform for both swirling and axial flow pneumatic conveying. A comparison of the calculations with the measured data shows a good agreement within an average error of less than 15 percent.     

Simulation of Gas-Solid Flow in Vertical Pipe by Hard-Sphere Model

This article presents a two-dimensional study of the gas-solid flow in a vertical pneumatic conveying pipe by means of a hard-sphere model where the motion of individual particles can be traced. Simulations were performed for a pipe of height 0.9 m and width 0.06 m, with air as gas phase and particles of density 900 kg/m³ and diameter 0.003 m as solid phase. Periodic boundary conditions were applied to the solid phase in the axial direction. Different cases were simulated to examine the effects of the number of particles used, superficial gas velocity, and restitution coefficient. The results show that the main features of plug flow can be reasonably captured by the proposed simulation technique. That is, increasing the number of particles in a simulation will increase the length of plugs but does not change the velocity of plugs; the solid fraction of a plug is relatively low if the number of particles is small. In particular, it is shown that increasing superficial gas velocity will increase the velocity of plugs and the frequency of plugs, and the pressure drop through a rising plug increases linearly with the plug length, suggesting that the total pressure of a conveying system with a given length can be quantified from the information of plug length and plug frequency. Increasing the restitution coefficient can promote the momentum transfer between particles and hence the raining down of particles from the back of a plug in vertical pneumatic conveying. The simulation offers a useful technique to understand the fundamentals governing the gas-solid flow under pneumatic conveying conditions.     

Motion of Large Particles in a Horizontal Pneumatic Pipe

The horizontal pneumatic transport of large particles with particle to pipe diameter ratio of 0.6 and particle densities of 928 kg/m³ and 2193 kg/m³ was examined experimentally and numerically. The pipe diameter and length were 10 mm and 8.8 m, respectively. The mean air velocity was between 14.2 m/s and 23.0 m/s and the number feed rate of particle was almost constant at seven per second. In this study, the method of characteristics was used for the simulation of gas flow, which considered not only the particle-particle collisions but also the particle-wall collisions. It is found that particle transport is possible even when the mean air velocity is smaller than the terminal settling velocity of particle's and that the arrival time intervals at the downstream section are not always uniform although the particles are fed uniformly. Furthermore, the velocity difference between different density particles becomes small as the mean air velocity decreases, because the particle velocities become uniform due to particle-particle collisions, and the ratio of particle velocity to the mean air velocity is almost independent of air velocity. In addition, it is shown that the particle-wall collision at the pipe joint due to pipeline misalignment can be one of the sources of bouncing motion of particles as shown by simulation results.     

A Numerical Simulation of Swirling Flow Pneumatic Conveying in a Vertical Pipeline

A numerical prediction for the axial and swirling pneumatic conveying in a vertical pipe was performed based on an Eulerian approach for the gas and a stochastic Lagrangian approach for the particles, where κ – ? turbulence model, the model of particle-particle and particle-wall collisions, was adopted. The numerical results are presented for polyethylene pellets of 3.2mm diameter conveyed through a pipeline of 12m in height with an inner diameter of 80mm. The initial swirl number was 0.0 and 0.68, the mean gas velocity varied from 11 to 17m/s, and the solid mass flow rate was 0.03 and 0.084 kg/s. From the numerical analysis, the swirl decay of the swirling gas-solid flow was found to be rapid in the acceleration region and approached the clean swirling flow in a fully developed region. The turbulent kinetic energy and energy dissipation rates of the swirling gas-solid flow increased near the wall and reduced in other regions. The comparison of predicted values with measured data showed a good agreement.     

Effect of Particle Properties on Slug Flow Conveying in a Horizontal Pneumatic Pipeline

The influence of particle properties on slug flow conveying was experimentally examined by using polyethylene particles of different densities from 825 kg/m³ to 945 kg/m³ in a horizontal pipeline 5.5 m in length, inside diameter of 32 mm, for air speeds below 8 m/s. It was found that hardness affects the slug flow conveying in such a way that for soft particles lower limiting velocity as well as boundary air velocities for suspension flow and slug flow increases. Additionally, it was found that the frictional characteristics of a particle influence its flow pattern. Also, there are two types of slug flow, that is, a solitary slug flow and a consecutive slug flow. In a solitary slug flow, there is at most only one plug in the pipeline. In a consecutive slug flow, the particles are conveyed continuously as slugs. There is always at least one slug in the pipeline.     

Numerical Study of Air Compressibility During Horizontal Pneumatic Transport

Using numerical simulations, the effect of the compressibility of air on the flow pattern of particles and pressure drop in the presence of particles during horizontal pneumatic transport operating under negative pressure was examined. The length and inside diameter of the pipeline were 30 m and 40 mm, respectively, and the chosen particles (4 mm in diameter) had densities of ρ_p = 1000 and 2000 kg/m³. The mean air velocities at pipe the inlet were U_inlet = 19, 22, and 28 m/s, and the range of the mass flow rate ratios of particle to air, μ, was varied up to 2.0. For a given inlet air velocity, the difference in the flow pattern between compressible and incompressible flow calculation is generally small. For ρ_p = 1000 kg/m³ particles the additional pressure drop in compressible flow increases when μ is above 0.5 and U_inlet is 28 m/s, μ is above 1.3 and U_inlet is 22 m/s, and μ is above 1.5 and U_inlet is 19 m/s. In these cases, the particle flow pattern is homogeneous. For ρ_p = 2000 kg/m³ particles, the pressure drop increases only when μ is above 1.5 and U_inlet is 28 m/s. The difference is not noticeable when the particle flow pattern is heterogeneous. Also, the difference in the additional pressure drop is much larger during homogeneous flow than heterogeneous flow.     

An Experimental Study on Degradation of Maize Starch During Pneumatic Transportation

Although attrition during pneumatic conveying is a common problem, very few publications can be found in the open literature on this subject. The particle-to-wall impact is perhaps the predominant cause of degradation since the particle impinges the wall surface at high velocities in dilute phase pneumatic conveying. The most important factors appear to be the conveying air velocity and moisture content. This article presents the experimental findings of a study on degradation of maize starch during pneumatic conveying process. The tests were carried out in a conveying setup having a pipe length of approximately 50 m and a pipe inner diameter of 50 mm in order to find out the breakage of particles under various airflow velocity conditions and temperatures. Dehumidified air was used during the experimentation, and the air temperatures used during these test were 100°C and 25°C. The experimental results indicated that for a given air temperature condition, the variation of attrition rate was a complex function of air velocity and solids loading ratio. Further, for any start pressure condition, the attrition rate was found to increase substantially with increase in air temperature.     

Numerical prediction of particle erosion of pipe bends

In the present study the Euler/Lagrange approach in combination with a proper turbulence model and full two-way coupling is applied for erosion estimation due to particle conveying along a horizontal to vertical pipe bend. Particle tracking considers both particle translational and rotational motion and all relevant forces such as drag, gravity/buoyancy and transverse lift due to shear and particle rotation were accounted for Laín and Sommerfeld (2012). Moreover, models for turbulent transport of the particles, collisions with rough walls and inter-particle collisions using a stochastic approach are considered Sommerfeld and Laín (2009). In this work, the different transport effects on spherical solid particle erosion in a pipe bend of a pneumatic conveying system are analysed. For describing the combined effect of cutting and deformation erosion the model of Oka et al. (2005) is used. Erosion depth was calculated for two- and four-way coupling and for mono-sized spherical glass beads as well as a size distribution of particles with the same number mean diameter (i.e. 40?μm). Additionally, particle mass loading was varied in the range from 0.3 to 1.0. The erosion model was validated on the basis of experiments by Mazumder et al. (2008) for a narrow vertical to horizontal pipe system with high conveying velocity. Then a 150?mm pipe system with 5?m horizontal pipe, pipe bend and 5?m vertical pipe with a bulk velocity of 27?m/s was considered for further analysis. As a result inter-particle collisions reduce erosion although the wall collision frequency is enhanced Sommerfeld and Laín (2015); additionally, considering a particle size distribution with the same number mean diameter as mono-sized particles yields much higher erosion depth. Finally, when particle mass loading is increased, bend erosion is reduced due to modifications of particle impact velocity and angle, although wall collision frequency grows.     

Wavelet Multi-Resolution Cross-Correlation Analysis of Swirling Gas-Solid Flow in a Horizontal Pipe

A wavelet multi-resolution cross-correlation analysis was developed and applied to experimental pressure-time signals in order to analyze the characteristics of swirling gas-solid flow in both Fourier and physical spaces. The experiment was carried out in a horizontal pipe with a length of 7.5 m and an inner diameter of 76 mm. The initial swirl number based on the total inflow was varied from 0.0 to 0.61, the mean gas velocity was varied from 6 to 28 m/s, and the solid mass flow rate was varied from 0.08 to 0.5. From the wavelet multi-resolution correlation analysis of the fluctuating pressure in the range of low air velocity, the characteristics of swirling gas-solid two-phase flows were extracted at various frequencies. Much stronger correlations were found in the range of low frequency, which implied periodic motion of dunes and sliding clusters. Additionally, it was revealed that the motion of a large cluster sliding flow contains two smaller clusters and the moving velocities of dunes were 1 m/s and 2 m/s, respectively. However, no correlation existed at smaller scales of correlation features, which indicated heterogeneous suspension flow.     

Measurements of Particle Velocity and Concentration for Dilute Swirling Gas-Solid Flow in a Vertical Pipe

Experimental studies concerning the characterization of a dilute swirling gas-solid flow were carried out in a vertical pipe with a height of 12 m and an inner diameter of 80 mm. Polyethylene pellets, with mean diameter of 3.2 mm, were used as test particles. The initial swirl number varied from 0.0 to 0.94, the mean gas velocity varied from 9 to 25 m/s, and the solid-gas ratio varied from 0.2 to 0.7. In this study, the particle velocity and concentration profiles were measured by the photographic image technique for both nonswirling (axial) and swirling gas-solid flows. It was found that the particle velocity of the swirling flow is lower than that of the axial flow in the range of high gas velocity; however, high particle velocity in the former flow can be obtained in the range of low gas velocity. The particle velocity profiles, on the other hand, were found to be nearly uniform in both the swirling and axial flows. The particle concentration profiles in the swirling flow exhibited symmetric distributions with respect to the pipe axis, and a higher particle concentration appeared in the vicinity of the wall located in the acceleration region.

gas-solid two-phase flow particle concentration particle velocity pipeline swirling flow     

The effect of oscillating flow on a horizontal dilute-phase pneumatic conveying

ABSTRACT

A horizontal dilute-phase pneumatic conveying system using vertically oscillating soft fins at the inlet of the gas–particle mixture was studied to reduce the power consumption and conveying velocity in the conveying process. The effect of different fin lengths on horizontal pneumatic conveying was studied in terms of the pressure drop, conveying velocity, power consumption, particle velocity, and intensity of particle fluctuation velocity for the case of a low solid mass flow rate. The conveying pipeline consisted of a horizontal smooth acrylic tube with an inner diameter of 80 mm and a length of approximately 5 m. Two types of polyethylene particles with diameters of 2.3 and 3.3 mm were used as conveying materials. The superficial air velocity was varied from 10 to 17 m/s, and the solid mass flow rates were 0.25 and 0.20 kg/s. Compared with conventional pneumatic conveying, the pressure drop, MPD (minimum pressure drop), critical velocities, and power consumption can be reduced by using soft fins in a lower air velocity range, and the efficiency of fins becomes more evident when increasing the length of fins or touching particles stream by the long fins. The maximum reduction rates of the MPD velocity and power consumption when using soft fins are approximately 15% and 26%, respectively. The magnitude of the vertical particle velocity for different lengths of fins is clearly lower than that of the vertical particle velocity for a non-fin conveying system near the bottom of the pipeline, indicating that the particles are easily suspended. The intensities of particle fluctuation velocity of using fins are larger than that of non-fin. The high particle fluctuation energy implies that particles are easily suspended and are easily conveyed and accelerated.     

DISTRIBUTIONS OF THE TANGENTIAL VELOCITIES ON THE DUST LADEN GAS FLOW IN THE CYLINDRICAL CYCLONE DUST COLLECTOR

The authors measured the distributions of the tangential velocities of the feed dust concentration C_o = 0. 6 ~15. 0 g/ m³ by the hot wire anemometers. The test dust was fly-ash which had the mean diameter Xpn = 2.03 μm. The used cylindrical cyclone had the diameter D1 = 140 mm, the diameter of the exit pipe D2 = 50 mn and the total length HT = 382 mm. In order to measure the fluctuating velocities and the time mean velocity on the dust Iaden gas flow and on the pure air flow, we had applied two kinds of the hot-wires. The flow Reynolds number Rec was Rec = Qo/HiV = 797~5582. The expert mental results sho-ed that there were no distinct differences of the time mean and fl uctuating velocities between the pure air flow and the dust laden gas flow. Then the authors have tried to explain those expert mental results by the response time of the fine solid particles and that of the scale of the nixing length in the turbulent rotational air flow.     

Simulation of Gas-Solid Flow in Vertical Pipe by Hard-Sphere Model

ABSTRACT

This article presents a two-dimensional study of the gas-solid flow in a vertical pneumatic conveying pipe by means of a hard-sphere model where the motion of individual particles can be traced. Simulations were performed for a pipe of height 0.9 m and width 0.06 m, with air as gas phase and particles of density 900 kg/m³ and diameter 0.003 m as solid phase. Periodic boundary conditions were applied to the solid phase in the axial direction. Different cases were simulated to examine the effects of the number of particles used, superficial gas velocity, and restitution coefficient. The results show that the main features of plug flow can be reasonably captured by the proposed simulation technique. That is, increasing the number of particles in a simulation will increase the length of plugs but does not change the velocity of plugs; the solid fraction of a plug is relatively low if the number of particles is small. In particular, it is shown that increasing superficial gas velocity will increase the velocity of plugs and the frequency of plugs, and the pressure drop through a rising plug increases linearly with the plug length, suggesting that the total pressure of a conveying system with a given length can be quantified from the information of plug length and plug frequency. Increasing the restitution coefficient can promote the momentum transfer between particles and hence the raining down of particles from the back of a plug in vertical pneumatic conveying. The simulation offers a useful technique to understand the fundamentals governing the gas-solid flow under pneumatic conveying conditions.     

Particle dynamics analysis in bend in a horizontal-vertical pneumatic conveying system with oscillatory flow

The pneumatic system is frequently operated in the high air velocity region, which aggravates the power consumption and erosion of bend, and the intensive study of the particles motion characteristic on a horizontal-vertical pneumatic conveying in various curved 90° bends is necessary. This experimental study focuses on the particles motion characteristic of bend on the horizontal-vertical pneumatic conveying with oscillatory flow (generated by installing the oscillator) in terms of on pressure drop, powder consumption, the evolution of particle velocity and particle fluctuating intensity during flowing through bends. The results indicate that powder consumption can be reduced by using oscillatory flow, which is more obvious with a larger radius ratios bend. Meanwhile, the pressure drop proportion of bend is higher than average pressure drop of the system within the same distance. Otherwise, the total reduction particles velocity through bend is less while using oscillatory flow, which is more obvious using larger radius ratios bend. The particle velocity using oscillatory flow is higher than that of the conventional pneumatic conveying for the cases of larger radius ratios bend, and this effect is less evident while through a smaller radius bend.     

小麦颗粒弯管流动特性数值模拟研究

目的 为研究小麦颗粒在弯管处的气力输送的特性。方法 以欧拉-欧拉双流体模型为基础,结合壁面碰撞摩擦模型、颗粒动理学的固体应力和Gidaspow曳力模型构建出小麦颗粒在弯管处的气力输送模型,采用FLUENT对弯管处小麦颗粒气力输送过程进行数值模拟,分析小麦颗粒在流经弯管过程中及弯管后直管中的小麦颗粒密度分布、气固两相速度、小麦颗粒与壁面剪切力和颗粒相湍动能。结果 经过仿真分析和实验验证,小麦颗粒在流经弯管过程中,其颗粒相体积分数、气固两相速度、颗粒和壁面剪切力以及颗粒相湍动能4个方面随着流入弯管的角度变化而改变;由于颗粒-颗粒、颗粒-管壁之间的碰撞摩擦,小麦颗粒在流出弯管后随着输送距离的增大其各项参数逐渐减缓。结论 采用FLUENT软件进行仿真得到了弯管内小麦颗粒的流动特性,并通过实验验证了仿真的可靠性。此次研究结合气固两相理论,为弯管气力输送设计的研发和优化提供了理论基础。     

Modeling Dense-Phase Pneumatic Conveying of Powders Using Suspension Density

This article presents results of an investigation into the modeling of pressure drop in horizontal straight pipe section for fluidized dense-phase pneumatic conveying of powders. Suspension density and superficial air velocity have been used to model pressure drop for two-phase solids-gas flow. Two applicable models formats (developed by other researchers using two different definitions of suspension density) were used to represent the pressure drop due to solids-gas flow through straight pipe sections. Models were generated based on the test data of conveying power-station fly ash and electrostatic precipitator (ESP) dust (median particle diameter: 30 and 7 µm; particle density: 2300 and 3637 kg m^?3; loose-poured bulk density: 700 and 610 kg m^?3, respectively) through a relatively short length of a smaller diameter pipeline. The developed models were evaluated for their scale-up accuracy and stability by using them to predict the total pipeline pressure drop (with appropriate bend model) for 69 mm I.D. × 168 m; 105 mm I.D. × 168 m and 69 mm I.D. × 554 m pipes and comparing the predicted versus with experimental data. Results show that both the models with suspension density and air velocity generally provide relatively better prediction compared to the conventional use of solids loading ratio and Froude number. For fly ash, the two formats result in considerable different predictions, whereas they provide relatively similar results for ESP dust.     

An experimental study on a horizontal-vertical pneumatic conveying system using oscillatory flow

To reduce the power consumption of a horizontal-vertical pneumatic conveying system, an oscillator is mounted with a 45° oblique plane through the pipe axis in this study. This experimental study focuses on the effect of oscillatory flow using the oscillator on the horizontal-vertical pneumatic conveying system in terms of the overall pressure drop of the system, power consumption, local pressure drop, and particle velocity. Compared with conventional pneumatic conveying (axial-flow), the pressure drop and power consumption can be reduced using the oscillatory flow in a lower air velocity range. Meanwhile, the particle axial velocity of the oscillatory flow is higher than that of the axial-flow near the bottom of pipe. This outcome indicates that the accelerating effect of oscillatory flow is obvious near the bottom of the pipe, and the particle vertical velocity of the oscillatory flow is positive, whereas the particle vertical velocity of the axial-flow is almost negative. This result shows that the particles of the oscillatory flow are suspended sufficiently, but the particles of the axial-flow have a tendency of deposition. Furthermore, the fluctuation intensity of the particle velocity of the oscillatory flow is higher than that of the axial-flow, especially near the bottom of the pipe.