Influence of soft segment composition on phase-separated microstructure of polydimethylsiloxane-based segmented polyurethane copolymers

Segmented polyurethane block copolymers were synthesized using 4,4′-methylenediphenyl diisocyanate (MDI) and 1,4-butanediol (BDO) as hard segments and various soft segments derived from poly(hexamethylene oxide) (PHMO) and poly(dimethylsiloxane) (PDMS)-based macrodiols and mixtures thereof. The microstructure and degrees of phase separation were characterized using a variety of experimental methods. Copolymers synthesized with the PDMS macrodiol and from PDMS/PHMO macrodiol mixtures were found to consist of three phases: a PDMS phase; hard domains; and a mixed phase of PHMO, PDMS ether end group segments and some dissolved hard segments. Two models were used to characterize the small-angle X-ray scattering from these copolymers: pseudo two-phase and core-shell models. Analysis using both methods demonstrates that as the PDMS content in the soft segment mixture increases, the greater the fraction of hard segments involved in hard domains than are dissolved in the mixed phase. Findings from analysis of the carbonyl region of FTIR spectra are also in agreement with greater hard/soft segment demixing in copolymers containing higher PDMS contents.     

Temperature dependent microphase mixing of model polyurethanes with different intersegment compatibilities

In this paper we explore the temperature dependence of segregation of hard and soft segments of selected segmented polyurethane copolymers using synchrotron small-angle X-ray scattering (SAXS). The copolymers are composed of the same hard segments but three different soft segment chemistries, of particular interest in biomedical device applications. Hard segments are formed from 4,4′-methylenediphenyl diisocyanate and 1,4-butanediol, and soft segments from an aliphatic polycarbonate [poly(1,6-hexyl 1,2-ethyl carbonate)], poly(tetramethylenoxide), or a mixed soft segment synthesized from hydroxyl-terminated poly(dimethylsiloxane) [PDMS] and poly(hexamethylenoxide) macrodiols. The changes in SAXS relative invariants and interdomain spacings are indicative of gradual dissolution of phase separated hard and soft segments with increasing temperature. All copolymers investigated herein, even those containing PDMS soft segments, transform to the single-phase state at a temperature determined by the soft segment chemistry (and hard segment content). The SAXS findings, along with those from parallel temperature-controlled Fourier Transform infrared spectroscopy measurements, also facilitate assignment of the origin of the thermal events observed in the DSC thermograms of these materials.     

Effect of soft-segment CH2/O ratio on morphology and properties of a series of polyurethane elastomers

A series of six thermoplastic polyurethane elastomers were synthesized from a 4,4′-methylene diphenyl diisocyanate (MDI) and 1,4-butanediol (BDO) chain extender, with poly(ethyleneoxide) (PEO), poly(tetramethylene oxide) (PTMO), poly(hexamethylene oxide) (PHMO), poly(octamethylene oxide) (POMO), poly(decamethylene oxide) (PDMO), and poly(1,6-hexyl carbonate)diol (PCDO) macrodiol soft segments. The soft-segment molecular weights employed were similar (approximately 1000 g/mol) and each polyurethane contained 55% (w/w) of the soft-segment macrodiol. Differential scanning calorimetry (DSC), dynamic mechanical thermal analysis (DMTA), wide-angle X-ray diffraction (WAXD), and Fourier transform infrared spectroscopy (FTIR) techniques were employed to characterize the morphology. Tensile and Shore hardness tests were also performed. Materials were tested in the as-molded, solvent-cast, and annealed states. It was found that the polyurethanes produced from macrodiols with the highest CH₂/O ratio displayed greater hard-domain crystallinity, a higher degree of phase separation, and the greatest hardness, stiffness, and opacity. POMO- and PDMO-based polymers displayed evidence of paracrystallinity in the soft domains. The PCDO-based material displayed a higher degree of phase mixing compared to the polyether-based materials. Annealing increased hard-domain crystallinity in all the polyether-based materials. The solvent-cast POMO- and PDMO-based materials had poor mechanical properties and were difficult to cast. The materials containing macrodiols with the lowest CH₂/O ratio were more readily solvent-cost and produced strong, useful films. Morphologies of the solvent-cast materials differed greatly from those of the molded materials. © 1996 John Wiley & Sons, Inc.     

Soft segment composition and its influence on phase-separated morphology of PCL/PEG-based poly(urethane urea)s

A composition-dependent microphase separation of segmented poly(urethane urea)s (PUUs), based on a mixture of two hydrophobic (polycaprolactone) and hydrophilic (polyethylene glycol) polyols, is investigated. Synthesis of PUUs was carried out through the reaction of in situ generated AB-type macromonomers, prepared from the reaction of NCO-terminated urethane prepolymers, with benzoic acid in dimethyl sulfoxide as solvent/reagent at 40–80 °C. The segmented PUUs were characterized by different methods including FTIR and NMR spectroscopies, gel permeation chromatography, differential scanning calorimetry and dynamic mechanical analysis. Microphase separation in the synthesized PUUs was monitored using atomic force microscopy (AFM) to find a better insight into structure–property relationship of PUUs consisting of mixed polyols. Thermal analysis of the polymers revealed that by introducing poly(ethylene glycol) (PEG) in PUU backbone, a well-defined glass transition was obtained. The results of AFM showed that PCL-based poly(urethane urea) has a morphology in which hard segment domains were homogeneously distributed in the soft segment matrix. In the samples based on PCL/PEG, the hard segment domains aggregates were connected to each other and were inhomogeneously distributed in the matrix. Comparison of the overall data revealed that the differences in soft segment compositions had a marked effect on the molecular structure and the mechanical properties of PUUs.     

Polyurethane ionomers. I. Structure–properties relationships of polyurethane ionomers

The influence of chemical structure on mechanical properties of polyurethane ionomers (PU ionomers) has been examined. NCO-terminated prepolymers prepared from primarily 4,4-methylene bis(phenyl isocyanate) (MDI) and poly(oxytetramethylene) glycol (PTMO) were chain extended with tertiary amine-containing diols and the ionomers obtained by quaternization of the prepolymers. The N-methyldiethanolamine chain extender gave the best physical properties. The mechanical properties of the PU ionomers were improved with decreasing chain length of PTMO and with increasing concentration of quaternary ammonium centers (or NCO/OH ratio of PU prepolymers). A lower degree of quaternization resulted in a decrease in the mechanical properties of the resulting PU ionomers, but their properties could be improved by post-quaternization. The adhesion of the PU ionomers to aluminum and the glass transition temperature increased with increasing concentration of quaternizing centers.     

Effect of the degree of soft and hard segment ordering on the morphology and mechanical behavior of semicrystalline segmented polyurethanes

The hierarchical microstructure responsible for the unique energy-absorbing properties of natural materials, like native spider silk and wood, motivated the development of segmented polyurethanes with soft segments containing multiple levels of order. As a first step in correlating the effects of crystallinity in the soft segment phase to the hard segment phase, we chose to examine the morphology and mechanical behavior of polyurethanes containing polyether soft blocks with varying tendencies to crystallize and phase segregate and the evolution of the microstructure with deformation. A series of high molecular weight polyurethanes containing poly(ethylene oxide) (PEO) (1000 and 4600 g/mol) and poly(ethylene oxide)-poly(propylene oxide)-poly(ethylene oxide) (PEO-PPO-PEO) (1900 g/mol) soft segments with varying hard segment content were synthesized using a two-step solution polymerization method. The presence of soft segment crystallinity (PEO 1000 g/mol) was shown to improve the storage modulus of the segmented polyurethanes below the T_m of the soft block and to enhance toughness compared to the PEO-PPO-PEO soft segment polyurethanes. We postulate that this enhancement in mechanical behavior is the result of crystalline soft regions that serve as an additional load-bearing component during deformation. Morphological characterization also revealed that the microstructure of the segmented polyurethanes shifts from soft segment continuous to interconnected and/or hard domain continuous with increasing hard segment size, resulting in diminished ultimate elongation, but enhanced initial moduli and tensile strengths. Tuning the soft segment phase crystallinity may ultimately lead to tougher polyurethane fibers.     

A novel side chain liquid crystalline polyurethane

Summary Side chain liquid crystalline polyurethanes (SCLP) without flexible spacer were synthesized by a two step block copolymerization reaction. The polyurethanes were based on azobenzene-type mesogenic diol chain extender (DR-19), a poly(tetramethylene oxide) (PTMO) soft segment, and different diisocyanates, including 4,4-diphenylmethane diisocyanate (MDI) and hexamethylene diisocyanate (HDI). The polyurethane samples obtained from DR-19 or DR-19 and PTMO with HDI had mesomorphic phases as determined by DSC and polarizing microscopy. Received: 19 March 1998/Revised version: 27 May 1998/Accepted: 17 June 1998     

Crystallization and melting behavior of the crystalline soft segment in a shape‐memory polyurethane ionomer

To illustrate the crystallization properties of soft segments in shape‐memory polyurethane (SMPU) ionomers, a series of SMPU ionomers with various ionic group contents and two kinds of counterions were synthesized with a prepolymerization method. An isothermal crystallization kinetic method was used to analyze the effects of ionic groups within the hard segments on the crystallization of the soft segments in a heating and cooling routine similar to that in a shape‐memory function. The more ionic groups there were within the hard segments, the lower the crystallization rate was of the soft segments. The crystallization mechanism of the SMPU ionomers was quite close to that of a control sample on the basis of similar Avrami exponents; the counterion category also had some influence on the crystallization rate. Meanwhile, the melting behavior after isothermal crystallization reflected the fact that the thermal history of the hard segments had a huge effect on the crystallization mechanism of the soft segments. Especially for the SMPU ionomer quenched from 240°C, the crystallization time dependence of the secondary crystallization was rather significant, but for the SMPU ionomer quenched from 70°C, the primary crystallization of the poly(?‐caprolactone) soft segment was predominant. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Novel quinoline-based polyurethane elastomers. The effect of the hard segment structure in properties enhancement

Polyurethane elastomers incorporating a quinoline moiety along their polymeric backbones and aliphatic, aromatic or heterocyclic crosslinkers have been synthesized and characterized. For this, NCO-terminated urethane oligomers were prepared from poly(butylene adipate) diol and methylene diphenyl diisocyanate and were subsequently chain extended with 2,4-quinolinediol and different crosslinkers. This study reports the influence of the different crosslinker chemical structures and the hard segment molar ratio on the thermal and dynamic mechanical thermal properties, as well as on the mechanical properties of these elastomers. The fluorescence spectra of polyurethane elastomers were determined at an excitation wavelength of 290 nm. The different chemical structures of the crosslinkers determine the hard segment cohesion and reduce the mobility of the soft phase, having an important effect on thermal stability and on the mechanical properties of the polyurethane films. Thus the incorporation of aromatic crosslinkers results in polyurethanes with lower elongation and stress at break. The highest mechanical properties were obtained for polyurethanes crosslinked with aliphatic crosslinkers.     

Synthesis and characterization of a series of poly(alkylene carbonate) macrodiols and the effect of their structure on the properties of polyurethanes

A series of polycarbonate and copolycarbonate macrodiols was prepared by using an ester interchange reaction with ethylene carbonate and diols such as 1,6-hexanediol, 1,10-decanediol, 2,2-diethyl-1,3-propanediol, 1,4-cyclohexanedimethanol, and 1,3-bis(4-hydroxybutyl)-1,1,3,3-tetramethyldisiloxane. The diols were chosen to prepare a series of macrodiols with different structural features including linear, branched, rigid, and flexible. The macrodiols were characterized by ¹H- and ¹³C-NMR spectroscopy and DSC. The commercial macrodiol based on 1,6-hexanediol exhibited a high level of crystallinity, while with the exception of 1,10-decanediol–based copolycarbonates all the others were completely amorphous. 1,10-Decanediol–based materials showed partial crystallinity under subambient conditions. A series of polyurethane elastomers with a constant hard segment percentage (40 wt %) was prepared using 4,4′-methylenediphenyl diisocyanate and 1,4-butanediol as the hard segment. Tensile test results and Shore hardness measurements demonstrated that polyurethanes based on polycarbonate macrodiols prepared from 1,3-bis(4-hydroxybutyl)-1,1,3,3-tetramethyldisiloxane had the lowest modulus and hardness of the series of polyurethanes. The remaining polyurethanes had high tensile strength with poor elasticity. The morphology of the polyurethanes, as determined by DSC analysis, varied from completely phase-mixed to well phase-separated structures. Polyurethanes based on macrodiols prepared from 1,3-bis(4-hydroxybutyl)-1,1,3,3-tetramethyldisiloxane showed good phase-separated morphology, with sharp hard segment melting endotherms and soft segment glass transitions close to that of the pure soft segment. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 69: 1621–1633, 1998     

The effect of diisocyanate isomer composition on properties and morphology of polyurethanes based on 4,4′-dicyclohexyl methane diisocyanate and mixed macrodiols (PDMS–PHMO)

Three series of polyurethanes were prepared having 42 wt % hard segments based on 4,4′-dicyclohexyl methane diisocyanate (H₁₂MDI) with trans,trans isomer contents in the 13 to 95 mol % range and 1,4-butanediol chain extender. The soft segments were based on macrodiols poly(hexamethylene oxide) (PHMO, MW 696), α,ω-bishydroxyethoxypropyl polydimethylsiloxane (PDMS, MW 940), and two mixed macrodiol compositions consisting of 80 and 20% (w/w) PDMS. H₁₂MDI with 35, 85, and 95% trans,trans isomer contents were obtained from commercial H₁₂MDI (13% trans, trans) by fractional crystallization, and all polyurethanes were prepared by a one-step bulk polymerization procedure. The polyurethanes based on the commercial diisocyanate-produced materials soluble in DMF with molecular weights in the 53,655–75,300 range and generally yielded clear and transparent materials. The polyurethanes based on H₁₂MDI with trans,trans contents of 35% or higher yielded materials insoluble in N,N-dimethylformamide (DMF) and were generally opaque. Mechanical properties, such as tensile strength and elongation at break, decreased with increasing trans,trans content, while the Young's modulus and Shore hardness increased. The polyurethanes based on mixed macrodiols yielded higher tensile properties than those of materials based on individual macrodiols. The best mechanical properties were observed for a polyurethane consisting of a soft segment based on PDMS–PHMO (80/20) and a hard segment based on commercial H₁₂MDI and BDO. Differential scanning calorimetry (DSC) and Fourier transform infrared spectroscopy (FTIR) were employed to characterize the polyurethane morphology. DSC results confirmed that the polyurethanes based on H₁₂MDI with high trans,trans isomer were very highly phase separated, exhibiting characteristic hard segment melting endotherms as high as 255°C. The other materials were generally phase mixed. FTIR spectroscopy results corroborated DSC results. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 73: 573–582, 1999     

Morphology and mechanical behavior of poly(vinyl chloride)/poly(butadiene–co–acrylonitrile) latex interpenetrating polymer networks

A series of poly(vinyl chloride)/poly(butadiene–co–acrylonitrile) interpenetrating polymer networks (IPNs), all having 50/(25–25) weight compositions, was synthesized in latex form. The latex particles were studied after each step of the two-staged polymerization and after molding or casting. Transmission electron microscopy together with dynamic mechanical spectroscopy suggest a graded composition within the latexes, in which the poly(vinyl chloride) seed latex network I forms a core that is partially penetrated by the poly(butadiene–co–acrylonitrile) network II, yielding increased amounts of poly(butadiene–co–acrylonitrile) in the shell of the latex particles.     

The preparation and characteristics of poly(methyl methacrylate–methylacrylate acid)/nano-ZnO composite latex particles

In this work, poly(methyl methacrylate-co-methylacrylate acid)/ZnO (poly(MMA–MAA)/ZnO) composite latex particle was synthesized by three steps The first step was to synthesize poly(MMA–MAA) copolymer latex particles by soapless emulsion polymerization. Following the first step, the second step was to polymerize MMA, MAA and 3,3-(trimethoxysilyl) propyl methacrylate (MPS) in the presence of poly(MMA–MAA) seed latex particles to form the poly(MMA–MAA)/poly(MMA–MAA–MPS) core–shell latex particles. In the third step, the poly(MMA–MAA)/poly(MMA–MAA–MPS) latex particles reacted with ZnO nanoparticles, which were synthesized by a traditional sol gel method, to form the polymer/inorganic poly(MMA–MAA)/poly(MMA–MAA–MPS)/ZnO composite latex. In this study, MPS with silanol groups essentially was used as the coupling agent to couple with ZnO nanoparticles, while the results of the study showed that there was not covalent bond existed between ZnO particles and polymer latex. The ZnO particles were adsorbed on the surface of polymer latex by electrostatic interaction. Besides, the linear poly(MMA–MAA)/crosslinking poly(MMA–MAA–MPS) core–shell latex particles which were synthesized in the second step were heated in the presence of ammonia to form the hollow poly(MMA–MAA–MPS) latex particles. The factors of heating time and concentration of crosslinking agent significantly influenced the morphology of hollow poly(MMA–MAA–MPS) latex particles.     

Studies on miscibility of poly(phenylene oxide)-based ionomer/polystyrene-based ionomer blends

The phase behavior of a series of blends obtained from mixing carboxylated poly(phenylene oxide) with sulfonated polystyrene and their respective neutralized ionomers was studied by differential scanning calorimetry. A substantially broader range of miscibility was observed when both blend components were functionalized, compared with blends in which only one of the components contained an acid group or was an ionomer. The properties of metallic cations which were used to neutralize the acid groups in the blends were found to have an effect on the miscibility. The miscibility of the two acid polymers or their ionomers depended on the difference of their functionalization level instead of on the absolute percentage of functional groups on each polymer. It was found that the two acid polymers or their ionomers remained miscible as long as they had a similar percentage of functional groups. © 1997 John Wiley & Sons, Inc. J Appl Polm Sci 65:341–346, 1997     

Structural characterization and mass transfer properties of polyurethane block copolymer: influence of mixed soft segment block and crystal melting temperature

An attempt has been made to investigate the influence of mixed soft segment on structure and mass transfer properties of segmented polyurethane (SPU). For this purpose polyurethane block copolymer containing soft segment such as polycaprolactone glycol (number‐average molecular weight 3000, PCL 3000), PCL 3000–polypropylene glycol (number‐average molecular weight 3000, PPG 3000), PCL 3000–polytetramethylene glycol (number‐average molecular weight 2900, PTMG 2900), PPG 3000–PTMG 2900, were synthesized using a two‐step or three‐step synthesis process. All the SPUs were modified with the hydrophilic segment, i.e. diol‐terminated poly(ethylene oxide) (number‐average molecular weight 3400, PEG 3400). Fourier‐transform infrared, wide‐angle X‐ray diffraction, differential scanning calorimetry, and dynamic mechanical thermal analysis were used to characterize the polyurethanes. The mass transfer properties were measured by equilibrium sorption and water vapor permeability measurements. Mixed blocks loosen the inter‐chain interaction due to phase mixing which decreases the crystallization of the soft segment in the resulting SPU. The crystallinity of mixed polyol block SPU increases when both polyols are crystallizable in the pure state. Highest loss tan δ value was observed for the sample containing PTMG 2900–PPG 3000 mixed soft segment due to their flexible and phase mixed structure which increases the chain mobility; this sample performed best among all four SPUs in equilibrium water sorption as well as water vapor permeability owing to their loose and nearly amorphous structure. Soft segment crystal melting further enhances the water vapor permeability significantly, which would make the membrane suitable for breathable textiles, packaging and medical applications. Copyright © 2006 Society of Chemical Industry     

The influence of composition ratio on the morphology of biomedical polyurethanes

Two series of thermoplastic polyurethane elastomers were synthesized from 4,4′‐methylenediphenyl diisocyanate (MDI), 1,4‐butanediol (BDO) chain extender, and each of poly(tetramethylene oxide) (PTMO) and poly(hexamethylene oxide) (PHMO) macrodiols. The PTMO and PHMO molecular weights were kept constant at 993 and 852 g/mol, respectively. In the PTMO‐based series, the composition ratio was varied between 48 and 58% (w/w) of macrodiol; 2 commercially available PTMO‐based polymers were also included. These were Pellethane 2363 80A® and its harder counterpart, Pellethane 2363 55D®. In the PHMO‐based series, the composition ratio was varied between 50 and 60% (w/w) of macrodiol. The materials were characterized by differential scanning calorimetry (DSC), dynamic mechanical thermal analysis (DMTA), wide‐angle X‐ray diffraction (WAXD), and small‐angle X‐ray scattering (SAXS). Mechanical performance was also assessed by tensile testing, stress hysteresis, and hardness testing. Altering the composition ratio had a similar effect on morphology and properties for both the PTMO and PHMO‐based series. An increase in hard segment content was associated with increased hard microdomain crystallinity, hardness, and stiffness. In both series, he beginning of hard microdomain interconnectivity was observed at a composition ratio of 52% soft segment. That is to say, for the processing and annealing conditions employed, macrodiol contents of 52% and below began to produce continuous, rather than discrete, hard microdomains. Pellethane 80A® was shown to have a discrete hard microdomain morphology, while Pellethane 55D® was shown to incorporate interconnecting hard microdomains. It is suggested that the superior biostability performance of Pellethane 55D relative to Pellethane 80A may be related to its interconnecting hard microdomain texture. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 71: 937–952, 1999     

Synthesis and Properties of Lignin-Based Polyurethane Hydrogels

Hydrogels were synthesized from acetic acid lignin by chemical crosslinking with NCO-terminated polyurethane ionomers (IPUI). The swelling ratio of hydrogels increased with pH. The hydrogel prepared at the mass ratio of m_AAL/m_IPUI: 0.35:1 presented maximum swelling ratio in pH 6.8 buffer solutions. The results of thermogravimetric analysis demonstrated that the thermal stability of the hydrogels is improved by the introduction of lignin. The data of release experiments for ammonium sulfate suggests that the hydrogels can be used as coating materials to prepare a slow-release fertilizer.     

Thermal stability of polyurethane elastomers before and after UV irradiation

In this work, we investigated the thermal degradation behavior of segmented polyurethane (PUR) elastomers before and after UV irradiation. The thermal degradation of PUR elastomers was studied over the temperature range of 25–600°C in an atmosphere of nitrogen using thermal gravimetric analysis (TGA). Four series of PUR elastomers derived from poly(oxytetramethylene)glycol (PTMO) of 1000 and 2000 molecular weight and poly(caprolactone glycol) (PCL) of 1250 molecular weight, 4,4′‐diphenylmethane diisocyanate (MDI), and 4,4′‐dicyclohexylmethane diisocyanate (H₁₂MDI) and 1,4‐butanediol as an chain extender were synthesized by the prepolymer method. The derivative thermogravimetric (DTG) peaks observed in the experiments indicated that PUR elastomers degraded through two steps. We attributed the first step to degradation of the hard segment. The second degradation step could be ascribed to degradation of the soft segment. We found that the PUR elastomers based on poly(ester polyol) and aromatic diisocyanate exhibit better thermal stability than that of PUR elastomers based on the poly(ether polyol) soft segment in both steps of degradation. The thermal degradation is more prevalent in PUR elastomers based on cycloaliphatic diisocyanate. The higher values of the temperature of initial decomposition (Tⁱ) indicate a higher thermal stability of UV‐exposed elastomers on the beginning of degradation. This may be due to the formation of a crosslinking structure in the presence of UV irradiation. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 79: 864–873, 2001     

Synthesis and characterization of copolymers based on poly(butylene terephthalate) and ethylene oxide‐poly(dimethylsiloxane)‐ethylene oxide

A series of thermoplastic elastomers based on ethylene oxide‐poly(dimethylsiloxane)‐ethylene oxide (EO‐PDMS‐EO), as the soft segment, and poly(butylene terephthalate) (PBT), as the hard segment, were synthesized by catalyzed two‐step, melt transesterification reaction of dimethyl terephthalate (DMT) with 1,4‐butanediol (BD) and α,ω‐dihydroxy‐(EO‐PDMS‐EO). Copolymers with a content of hard PBT segments between 40 and 90 mass % and a constant length of the soft EO‐PDMS‐EO segments were prepared. The siloxane prepolymer with hydrophilic terminal EO units was used to improve the miscibility between the polar comonomers, DMT and BD, and the nonpolar PDMS. The molecular structure and composition of the copolymers were determined by ¹H‐NMR spectroscopy, whereas the effectiveness of the incorporation of α,ω‐dihydroxy‐(EO‐PDMS‐EO) into the copolymer chains was verified by chloroform extraction. The effects of the structure and composition of the copolymers on the melting temperatures and the degree of crystallinity, as well as on the thermal degradation stability and some rheological properties, were studied. It was demonstrated that the degree of crystallinity, the melting and crystallization temperatures of the copolymers increased with increasing mass fraction of the PBT segments. The thermal stability of the copolymers was lower than that of PBT homopolymer, because of the presence of thermoliable ether bonds in the soft segments. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Synthesis and characterization of thermoplastic poly(ester–siloxane)s

Two series of thermoplastic poly(ester–siloxane)s, based on poly(dimethylsiloxane) (PDMS) as the soft segment and poly(butylene terephthalate) as the hard segment, were synthesized by two‐step catalyzed transesterification reactions in the melt. Incorporation of soft poly(dimethylsiloxane) segments into the copolyester backbone was accomplished in two different ways. The first series was prepared based on dimethyl terephthalate, 1,4‐butanediol and silanol‐terminated poly(dimethylsiloxane) (PDMS‐OH). For the second series, the PDMS‐OH was replaced by methyl diesters of carboxypropyl‐terminated poly(dimethylsiloxane)s. The syntheses were optimized in terms of both the concentration of catalyst, tetra‐n‐butyl‐titanate (Ti(OBu)₄), and stabilizer, N,N′‐diphenyl‐p‐phenylene‐diamine, as well as the reaction time. The reactions were followed by measuring the inherent viscosities of the reaction mixture. The molecular structures of the synthesized poly(ester–siloxane)s were verified by ¹H NMR spectroscopy, while their thermal properties were investigated using differential scanning calorimetry. © 2001 Society of Chemical Industry