一种应用于阵列TDC的低抖动锁相环设计

传统的PLL（Phase Locked Loop）电路受限于环路参数的选定,其相位噪声与抖动特性已经难以满足大阵列、高精度TDC（Time-to-Digital Converter）的应用需求.本文致力于PLL环路带宽的优化选取,采取TSMC 0.35μm CMOS工艺实现了一款应用于TDC的具有低抖动、低噪声特性的锁相环（Phase Locked Loop,PLL）电路,芯片面积约为0.745mm×0.368mm.实际测试结果表明,在外部信号源输入15.625MHz时钟信号的条件下,PLL输出频率可锁定在250.0007MHz,频率偏差为0.7kHz,输出时钟占空比为51.59%,相位噪声为114.66dBc/Hz@1MHz,均方根抖动为4.3ps,峰峰值抖动为32.2ps.锁相环的相位噪声显著降低,输出时钟的抖动特性明显优化,可满足高精度阵列TDC的应用需要.     

2-GHz CMOS锁相环时钟发生器研究与设计

采用包含预充电通路,自适应偏置的压控振荡器,设计了一种2-GHz锁相环时钟发生器,并用0.18μm混合信号CMOS工艺实现.分析了环路参数对锁相环输出噪声影响,并对环路参数进行优化.1.8V电源电压下2GHz时钟的rms抖动,peak-peak抖动的测试结果分别为7.27ps,37.5ps,功耗为42mW.     

用于高能物理实验电子读出芯片的低噪声锁相环芯片设计

基于TSMC 180 nm工艺设计并流片测试了一款用于高能物理实验的电子读出系统的低噪声、低功耗锁相环芯片。该芯片主要由鉴频鉴相器、电荷泵、环路滤波器、压控振荡器和分频器等子模块组成,在锁相环电荷泵模块中,使用共源共栅电流镜结构精准镜像电流以减小电流失配和用运放钳位电压进一步减小相位噪声。测试结果表明,该锁相环芯片在1.8 V电源电压、输入50 MHz参考时钟条件下,可稳定输出200 MHz的差分时钟信号,时钟均方根抖动为2.26 ps(0.45 mUI),相位噪声在1 MHz频偏处为-105.83 dBc/Hz。芯片整体功耗实测为23.4 mW,锁相环核心功耗为2.02 mW。     

Minimizing the Supply Sensitivity of a CMOS Ring Oscillator Through Jointly Biasing the Supply and Control Voltages

A method to minimize the supply sensitivity of a CMOS ring oscillator is proposed through joint biasing of the supply and the control voltage. The technique can supplement a number of common supply rejection techniques and can be exploited to compensate for the noise coupling caused by the parasitic capacitance in the loop filter of a phase-locked loop (PLL). The proposed CMOS ring oscillator is designed and implemented with a charge-pump based PLL in 65-nm technology to demonstrate the robustness against the supply fluctuation. Taking advantage of the negative static supply sensitivity of the ring oscillator with proper combination of the bias voltages, the rms jitter of the 5.12-GHz output clock is reduced from 6.41 ps to 2.38 ps while subject to supply noise at 90 MHz.      

低抖动的480 MHz CMOS电荷泵式锁相环

本文设计了一款用于USB2.0时钟发生作用的低抖动、低功耗电荷泵式锁相环电路。其电路结构包含鉴频/鉴相器、电荷泵、环路滤波器、压控振荡器和分频器。电路设计是基于CSM0.18μmCMOS工艺,经HSPICE仿真表明,锁相环输出480MHz时钟的峰峰值抖动仅为5.01ps,功耗仅为8.3mW。     

A 960-Mb/s/pin interface for skew-tolerant bus using low jitter PLL

This paper describes an I/O scheme for use in a high-speed bus which eliminates setup and hold time requirements between clock and data by using an oversampling method. The I/O circuit uses a low jitter phase-locked loop (PLL) which suppresses the effect of supply noise. Measured results show peak-to-peak jitter of 150 ps and r.m.s. jitter of 15.7 ps on the clock line. Two experimental chips with 4-pin interface have been fabricated with a 0.6 μm CMOS technology, which exhibits the bandwidth of 960 Mb/s per pin     

一种用于TDC的低功耗多相时钟生成电路北大核心

在无人机3D地形测绘中，作为核心模块的时间数字转换器(TDC)需要具有远距离测量能力和高测量分辨率。基于对测距系统的长续航、公里级测距能力和厘米级测量精度的综合考量，文章设计了一种用于TDC的低功耗多相位时钟生成电路。采用了伪差分环形压控振荡器，通过优化交叉耦合结构，在保证低功耗的前提下，提升了信号边缘的斜率，增强了时钟的抖动性能和对电源噪声的抑制能力。在电荷泵设计中，通过对环路带宽的考量选取了极低的偏置电流，在进一步降低功耗的同时缩小了环路滤波器的面积。基于SMIC 180 nm CMOS工艺完成了对多相时钟生成电路的设计。仿真结果表明，在400 MHz的输出频率下，环路带宽稳定在1 MHz。该电路在不同工艺角下均能达到较快的锁定速度，相位噪声为-88 dBc@1 MHz,功耗为1 mW,均方根抖动为27 ps,满足厘米级测距的精度需求。     

A low-jitter 1.9-V CMOS PLL for UltraSPARC microprocessorapplications

A phase-locked loop (PLL) for CMOS UltraSPARC microprocessor applications uses a loop filter referenced to a quiet power supply and achieves measured clock period jitter of ±25 ps at 360 MHz. The fully integrated CMOS PLL uses a charge-pump phase/frequency detector, a single-capacitor loop filter, and a feedforward error correction architecture. Loop characteristics are analyzed and verified by measurements. The measured sensitivity of clock period jitter to supply voltage is 2.6 ps/100 mv over an analog supply-voltage range of 1.6-2.1 V; the measured output operating frequency range is 8.5-660 MHz. Fabricated in an area of 310×280 μm² in a 0.25-μm CMOS process, the PLL dissipates 25 mW from a 1.9-V supply     

A portable clock multiplier generator using digital CMOS standardcells

High frequency clock rate is a key issue in today's VLSI. To improve performance on-chip, clock multipliers are used. But it is a difficult task to design such circuits while maintaining low cost. This paper presents a circuit fabricated to test a new method of clock frequency multiplication. This new approach uses a digital CMOS process in order to implement a fully integrated digital delay locked loop. This multiplier does not require external components. Moreover, as it is primarily intended for ASIC design, it is generated by a parameterized generator written in C which relies on a portable digital standard cell library for automatic place and route. The design based on the delay locked loop allows the clock waveform to reach its operating point faster than conventional methods. Special techniques enable high multiplication factors (between 4 and 20) without compromising the timing accuracy. With a clock multiplier of 20, in 1 μm CMOS process and a 5 V supply voltage, a 170 MHz clock signal has been obtained from a 8.5 MHz external clock with a measured jitter lower than 300 ps     

A DLL With Jitter Reduction Techniques and Quadrature Phase Generation for DRAM Interfaces

A DLL featuring jitter reduction techniques for a noisy environment is described. It controls a loop response mode by monitoring the magnitude of input jitter caused by supply noise. This technique varies the probability of phase error tracking. It reduces the output jitter of the DLL due to a low effective variance of input phase error and a narrow effective loop bandwidth. The DLL is implemented in a 0.13 $muhbox{m}$ CMOS process. Under noisy environments, the output clock of 1 GHz has 4.58 ps RMS and 29 ps peak-to-peak jitter.      

A semidigital dual delay-locked loop

This paper describes a dual delay-locked loop architecture which achieves low jitter, unlimited (modulo 2π) phase shift, and large operating range. The architecture employs a core loop to generate coarsely spaced clocks, which are then used by a peripheral loop to generate the main system clock through phase interpolation. The design of an experimental prototype in a 0.8-μm CMOS technology is described. The prototype achieves an operating range of 80 kHz-400 MHz. At 250 MHz, its peak-to-peak jitter with quiescent supply is 68 ps, and its jitter supply sensitivity is 0.4 ps/mV     

InP DHBT-Based Monolithically Integrated CDR/DEMUX IC Operating at 80 Gbit/s

In this paper, a monolithically integrated clock and data recovery (CDR) circuit with 1:2 demultiplexer (DEMUX), which is intended for use in 80 Gbit/s optical fiber links, is presented. The integrated circuit (IC) is manufactured using an in-house InP double heterostructure bipolar transistor (DHBT) technology, exhibiting cut-off frequency values of more than 220 GHz for both$f_T$and$f_max $. The CDR circuit in the topology of a phase-locked loop (PLL) is mainly composed of a half-rate linear phase detector including a 1:2 demultiplexer (DEMUX), a loop filter, and a voltage-controlled oscillator (VCO). Hence, the corresponding architecture of each of these components as well as the applied circuit design technique are extensively addressed. Concerning the performance achieved by the CDR/DEMUX IC, the recovered and demultiplexed 40 Gbit/s data from an 80 Gbit/s input signal feature clear eye opening with a signal swing as high as 600$hboxmV_ pp$. The extracted 40 GHz clock signal shows a phase noise as low as$- hbox98~dBc/hboxHz$at 100 kHz offset frequency. The corresponding rms jitter amounts to 0.37 ps while the peak-to-peak jitter is as low as 1.66 ps. At a single supply voltage of$-hbox4.8~V$, the power consumption of the full CDR/DEMUX IC amounts to 1.65 W. To the authors' best knowledge, this work demonstrates the first CDR circuit at the achieved data rate, regardless of all the competing semiconductor technologies.     

CMOS DLL-based 2-V 3.2-ps jitter 1-GHz clock synthesizer andtemperature-compensated tunable oscillator

This paper describes a low-voltage low-jitter clock synthesizer and a temperature-compensated tunable oscillator. Both of these circuits employ a self-correcting delay-locked loop (DLL) which solves the problem of false locking associated with conventional DLLs. This DLL does not require the delay control voltage to be set on power-up; it can recover from missing reference clock pulses and, because the delay range is not restricted, it can accommodate a variable reference clock frequency. The DLL provides multiple clock phases that are combined to produce the desired output frequency for the synthesizer, and provides temperature-compensated biasing for the tunable oscillator. With a 2-V supply the measured rms jitter for the 1-GHz synthesizer output was 3.2 ps. With a 3.3-V supply, rms jitter of 3.1 ps was measured for a 1.6-GHz output. The tunable oscillator has a 1.8% frequency variation over an ambient temperature range from 0°C to 85°C. The circuits were fabricated on a generic 0.5-μm digital CMOS process     

A low-power multiplying DLL for low-jitter multigigahertz clock generation in highly integrated digital chips

A multiplying delay-locked loop (MDLL) for high-speed on-chip clock generation that overcomes the drawbacks of phase-locked loops (PLLs) such as jitter accumulation, high sensitivity to supply, and substrate noise is described. The MDLL design removes such drawbacks while maintaining the advantages of a PLL for multirate frequency multiplication. This design also uses a supply regulator and filter to further reduce on-chip jitter generation. The MDLL, implemented in 0.18-/spl mu/m CMOS technology, occupies a total active area of 0.05 mm/sup 2/ and has a speed range of 200 MHz to 2 GHz with selectable multiplication ratios of M=4, 5, 8, 10. The complete synthesizer, including the output clock buffers, dissipates 12 mW from a 1.8-V supply at 2.0 GHz. This MDLL architecture is used as a clock multiplier integrated on a single chip for a 72/spl times/72 STS-1 grooming switch and has a jitter of 1.73 ps (rms) and 13.1 ps (pk-pk).     

A low jitter, low spur multiphase phase-locked loop for an IR-UWB receiver

A low jitter,low spur multiphase phase-locked loop(PLL) for an impulse radio ultra-wideband(IR-UWB) receiver is presented.The PLL is based on a ring oscillator in order to simultaneously meet the jitter requirement, low power consumption and multiphase clock output.In this design,a noise and matching improved voltage-controlled oscillator(VCO) is devised to enhance the timing accuracy and phase noise performance of multiphase clocks.By good matching achieved in the charge pump and careful choice of the l...     

用于时钟恢复电路的低抖动可变延迟线锁相环电路

文中给出了一个基于压控可变延迟线的电荷泵锁相环电路的设计,用于时钟恢复电路中采样时钟沿的定位,它的工作不受环境和工艺的影响,保证了采集数据的准确性。应用于延迟线中的改进的延迟单元有效地减小了相位抖动,环路滤波电路的设计避免了电荷重新分配引入的影响。电路采用0.35umTSMC的MOS工艺,在3.3V的低电压下工作,模拟得到在最坏情况下,单个延迟模块的相位抖动为20ps,输出静态相位误差仅45ps。     

10 GHz full-rate clock and data recovery circuit in 0.18 /spl mu/m CMOS without external reference clock

The design of a fully monolithic integrated 10 GHz full-rate clock and data recovery (CDR) circuit in 0.18 /spl mu/m digital CMOS technology, which employs an injection phase-locked loop (PLL) technique is presented. The CDR operating without the external reference exhibits a capture range of 200 MHz while consuming 205 mA current from 1.8 V supply including the output buffer. The recovered clock signal with 250 mV/sub pp/ pseudorandom bit Sequence input data of length 2/sup 31/-1 exhibits 7.9 ps of peak-to-peak (p-p) and 1.1 ps of root-mean-square (RMS) jitter. The measured clock phase noise at 1 MHz offset is approximately -109 dBc/Hz.     

High-speed circuit designs for transmitters in broadband data links

Various high-speed techniques including internal peaking, differentially stacked inductor, and dual-loop PLL for wireline communications are proposed,analyzed, and verified by means of three independent circuits. A multiplexer incorporates multiple peaking techniques and gate control switching to achieve an operation speed of 20 Gb/s while consuming 22 mW from a 1.8-V supply. A voltage-controlled oscillator employing differentially stacked inductor accomplishes a phase noise of -90dBc/Hzat 1-MHz offset with a minimum power of 1 mW. A clock multiplication unit utilizes dual-loop architecture as well as a third-order loop filter, arriving at an output jitter of 0.2 ps, rms (0.87 ps, rms de-embedding 0.84 ps, rms from the instruments) and 4.5 ps, pp while consuming 40 mW from a 1.8-V supply.     

A high-speed, low-power clock generator for a microprocessorapplication

This paper discusses the design of the clock generator for the Alpha 21264. As the speed performances are of primary concern in the whole design, the clock-generator jitter and phase misalignment must be as low as possible in a very noisy environment. A dedicated on-chip voltage regulator based on a bandgap reference has been designed to reduce the effect of supply noise on the clock generator. To avoid a large voltage drop across the power-supply bond wires during the startup sequence, the core frequency can be increased by steps in one period of the core clock, with a limited frequency overshoot and no missing pulses. The circuit has been implemented in a CMOS 0.35 μm process. The voltage-controlled-oscillator frequency range is between 350 MHz and 2.8 GHz, with a peak-to-peak cycle-to-cycle jitter lower than 16 ps. While booting Unix on a system, the maximum phase misalignment is lower than ±100 ps     

Novel system clock generation from a modulated signal

This paper describes a novel technique to derive a pure-spectral system clock with a common multi-modulus divider from a frequency modulated signal. Therefore, the dividing factor is inverse frequency modulated to compensate the frequency modulation component on the divider input signal. Additionally, $\Upsigma\Updelta$ dithering is applied to the frequency divider. The technique is used for a FM-radio transmitter based on an all-digital phase-locked loop (PLL) to generate a higher-frequency clock for baseband signal processing. It can also be applied to other PLL based transmitters or receivers, especially, if only a slow PLL reference clock is available and a faster system or baseband clock is required. The main factor determining the quality of the generated clock signal is the PLL??s reference quartz oscillator as it determines the accuracy of the PLL??s RF oscillator, which limits then the accuracy of the newly generated clock. In the FM-radio transmitter, a generated ??1?MHz clock signal with 30.58?ppm frequency offset and 515?ps root mean square jitter is generated. The phase noise is determined to ?83.5?dBc/Hz at 10?kHz offset and ?70.5?dBc/Hz at 1?kHz, respectively. The signal can also be used in co-integrated or external circuits.