氧化铈-二氧化硅介孔材料制备及对铜离子的吸附性能

采用共沉淀法和沉淀浸渍法制备了纳米氧化铈-二氧化硅（CeO₂-SiO₂）介孔材料吸附剂,主要考察了其对水中铜离子（Cu²⁺）的吸附行为。通过X射线衍射（XRD）、扫描电镜（SEM）和氮吸附（BET）等手段对合成的介孔材料进行了性能表征,并通过静态吸附实验分析了溶液pH、溶液初始金属离子质量浓度、吸附剂用量、吸附时间等条件对介孔材料吸附Cu²⁺性能的影响。结果表明：共沉淀法制备的纳米CeO₂-SiO₂介孔材料对Cu²⁺的去除效果较沉淀浸渍法要好;当溶液pH=7.0时CeO₂-SiO₂介孔材料对Cu²⁺的吸附效果最好,20 min时基本达到吸附平衡;溶液初始Cu²⁺浓度增大Cu²⁺去除率降低,Cu²⁺累计吸附量增大;随着吸附剂用量增加Cu²⁺去除率增大,当CeO₂-SiO₂吸附剂用量为0.15 g/L时对Cu²⁺的去除率趋于稳定;CeO₂-SiO₂吸附剂对不同金属离子吸附性能由大到小的顺序为Cu²⁺、Fe²⁺、Mn²⁺,该吸附过程均符合准二级动力学模型。     

新型淀粉基微球对Cu~(2+)、Pb~(2+)吸附性能的研究

研究了新型淀粉基微球对Cu2+、Pb2+的吸附性能,结果表明,淀粉基微球对Cu2+的吸附能力强于Pb2+,对Cu2+、Pb2+的吸附率可达到85%以上,是一种有效处理重金属离子废水的处理剂。     

Interaction of metal ions with montmorillonite and vermiculite

The behaviour of montmorillonite and vermiculite toward adsorption of Cd²⁺, Pb²⁺, Zn²⁺, Mn²⁺, Cu²⁺ and Zn²⁺ was compared. In general, the uptake of metal ions on both clay minerals decreased with decreasing of pH and in the presence of ligands forming stable complexes. Metal ion retention on montmorillonite was less affected by the competition of sodium ions at high ionic strengths with respect to vermiculite. On the other hand, the total capacity of vermiculite with respect to the investigated metal ions was found to be much higher than that of montmorillonite, whereas the order of affinity of the metal ions for the two clay minerals was similar, i.e.: Pb²⁺ = Cd²⁺ < Cu²⁺ < Zn²⁺ < Mn²⁺ < Ni²⁺ for montmorillonite and Pb²⁺ < Cu²⁺ < Cd²⁺ < Zn²⁺ < Ni²⁺ < Mn²⁺ for vermiculite.The similarities and differences between the two clay minerals were also investigated by principal component analysis and hierarchical cluster analysis.The results of this study may be used to predict the uptake efficiency of these adsorbents in view of their application for the removal of metal ions from contaminated effluents. The choice of vermiculite or montmorillonite for the uptake of metal ions or other elements will depend on the composition of the effluent to be treated.     

Effect of light metal ions on the sorption of heavy metal ions on natural polymers

Dried ground formaldehyde-treated peanut skins, white ash bark, and So. Wisconsin red maple bark are efficient substrates for removal of many heavy metal ions from waste streams, but possible interference by common light metal cations has never been determined. The influence of Ca²⁺, Mg²⁺, or Na⁺ on the removal of the heavy metal ions Pb²⁺, Cu²⁺, Cd²⁺, and Zn²⁺ by the above substrates was studied in both batch and packed-column experiments. It was found that Pb²⁺ and Cu²⁺ were minimally affected by the presence of these light metal ions in solution, while the uptake of Cd²⁺ and Zn²⁺ was significantly reduced. Calcium ion produced the greatest effect of the light metals tested.     

Preparation of graphene oxide aerogel and its adsorption for Cu2+ ions

Graphene oxide (GO) aerogels were prepared by a unidirectional freeze-drying method (UFDM), their structure was observed and their adsorption performance for Cu²⁺ in aqueous solution was evaluated. The results show that GO aerogels have unidirectional porous structure and good adsorption ability for Cu²⁺. The adsorption system is depended on the Cu²⁺ concentration and follows a pseudo second-order kinetic model. The adsorption equilibrium is reached soon. The adsorption isotherms are simulated well by the Langmuir model. The adsorption of Cu²⁺ on GO aerogels is strongly dependent on pH, indicating an ion exchange mechanism. The obtained results demonstrated that the GO aerogels can be used as an effective adsorbent for Cu²⁺ removal from water.     

不同金属离子掺杂TiO2薄膜的制备及光催化活性的研究

以溶胶-凝胶法制备了分别用Ag^+、Cu²⁺、Fe³⁺、La³⁺、Ce³⁺和Eu³⁺等离子掺杂的纳米TiO₂薄膜，经XRD和UV-Vis对薄膜样品进行表征并研究了其光催化活性。XRD结果证明，掺镧TiO₂薄膜与未掺杂薄膜的X射线衍射图基本一致，实验条件下主要为锐钛矿型，且掺入La^3+离子使得TiO₂薄膜的晶粒变小。UV-Vis吸收光谱说明当λ＞380 nm时，其吸光度低于0.15。薄膜光催化降解亚甲基蓝的实验表明,La³⁺或Fe^3+掺杂薄膜的光催化降解率远高于未掺杂TiO₂薄膜，而Ce^3+或Cu^2+离子掺杂薄膜与未掺杂薄膜的光催化活性相似，掺Ag⁺或Eu³⁺离子则降低了活性。当最佳掺杂量La³⁺为0.6%或Fe³⁺为1.5%时，光催化降解率分别高达92%和82%。     

不同变质程度超微煤粉对重金属离子的吸附性能

重金属离子由于具有毒性、难以生物降解且可在生物体内累积,严重威胁人类的身体健康。吸附是去除重金属离子的一种可行有效的方法。本文选择褐煤、烟煤、无烟煤3种变质程度不同的煤种,通过高能球磨获得超微煤粉。研究了3种超微煤粉对水溶液中Ni²⁺和Cr⁶⁺的吸附动力学与热力学以及投加量与pH值对吸附效果的影响。结果表明3种煤粉对Ni²⁺、Cr⁶⁺的吸附量均随时间的增加而增加,并且Ni²⁺的处理效果明显好于Cr⁶⁺,在180min时褐煤、无烟煤与烟煤对Ni²⁺、Cr⁶⁺的吸附量分别为3.906mg/g、3.582mg/g、2.983mg/g和1.953mg/g、1.774mg/g、0.487mg/g。3种煤粉对两种重金属离子的吸附均符合二级吸附动力学和Freundlich等温式,随着投加量与pH值的增加,去除效果增加,在相同条件下,褐煤的吸附效果优于烟煤与无烟煤。     

Formation of thermosensitive copolymer beads having phosphinic acid groups and adsorption ability for metal ions

Hydrophilic thermosensitive copolymer beads having phosphinic acid groups were prepared by suspension copolymerization of acryloyloxypropyl n‐octylphosphinic acid (APPO), N‐isopropyl acrylamide (NIPAAm), and tetraethyleneglycol dimethacrylate (4G). The thermosensitivity and the adsorption ability of the copolymer beads for metal ions beads were studied. The APPO‐NIPAAm‐4G copolymer beads were obtained in a good yield by suspension copolymerization of monomers (APPO, NIPAAm, and 4G) dissolved in chloroform, in a saturated Na₂SO₄ aqueous solution in the presence of surfactant and MgCO₃. The APPO‐NIPAAm‐4G copolymer beads had higher adsorption ability for lanthanide metal ions (Eu³⁺, Sm³⁺, Nd³⁺, or La³⁺) than for main transition metal ions (Cu²⁺, Ni²⁺, or Co²⁺). Furthermore, it was also found that the APPO‐NIPAAm‐4G copolymer beads had selective adsorption ability between lanthanide metal ions, and the order of adsorption ability for lanthanide metal ions was as follows: Eu³⁺ > Sm³⁺ > Nd³⁺ > La³⁺. The selective adsorption for these metal ions from their mixed solutions was performed by both a batch method and a column method. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 449–460, 2006     

衍生-超临界CO2萃取土壤样品中的金属离子

The method of using trifluoro acetyl acetone as chelating agent to extract Cu^2 , Hg^2 , Pb^2 ,Zn^2 , Cd^2 , Cr^3 from silica gel and soil sample by supercritical CO2 was investigated. The extracts were analyzed with the atomic absorption spectrophotometry method. The experimental results showed that at 20 MPa, 60℃ and with methanol as modifier, the metal ions mentioned above could be extracted efficiently. The recovery values for the simulated silica gel samples and soil sample were 91.0%-98. 2%and 77.8%-93.9%, respectively. This method was proved to be simple, quick and without pollution, which could be applied to the analysis of heavy metal ions in environmental samples.     

Binding of heavy metal ions by formaldehyde-polymerized peanut skins

Peanut skin, when treated with formaldehyde to polymerize tannins, is a highly efficient substrate for removal of many heavy metal ions from aqueous waste solutions. The ions Ag¹⁺, Cd²⁺, Cr⁶⁺, Cu²⁺, Hg²⁺, Ni²⁺, Pb²⁺, Zn²⁺, as well as Ca²⁺ and Mg²⁺, were contacted with formaldehyde-treated peanut skin. Quantitative removal could be achieved with Ag¹⁺, Cd²⁺, Cu²⁺, Hg²⁺, Pb²⁺, and Zn²⁺. Capacity of the substrate for ions was promising for Pb²⁺ (2.1 meq/g substrate), Cu²⁺ (3.0 meq/g), and Cd²⁺ (1.3 meq/g). Sorption from a solution containing Cd²⁺, Cu²⁺, Hg²⁺, Ni²⁺, Pb²⁺, Zn²⁺, on a packed column of formaldehyde-treated peanut skin indicated that Hg²⁺, Pb²⁺, and Cu²⁺ were rapidly and completely bound to the packing, while Cd²⁺, Ni²⁺, and Zn²⁺ were poorly bound until the preferred ions had been removed from solution.     

Ultrafiltration recovery of alginate: Membrane fouling mitigation by multivalent metal ions and properties of recycled materials

Recovery of alginate extracted from aerobic granular sludge (AGS) has given rise to a novel research direction. However, these extracted alginate solutions have a water content of nearly 100%. Alternately, ultrafiltration (UF) is generally used for concentration of polymers. Furthermore, the introduction of multivalent metal ions into alginate may provide a promising method for the development of novel nanomaterials. In this study, membrane fouling mitigation by multivalent metal ions, both individually and in combination, and properties of recycled materials were investigated for UF recovery of sodium alginate (SA). The filtration resistance showed a significantly negative correlation with the concentration of metal ions, arranged in the order of Mg²⁺ < Ca²⁺ < Fe³⁺ < Al³⁺ (filtration resistance mitigation), and the moisture content of recycled filter cake showed a marked decrease. For Ca²⁺, Mg²⁺, Fe³⁺, and Ca²⁺+Fe³⁺, the filtration resistances were almost the same when the total charge concentration was less than 5 mmol·L^-1. However, when the total charge concentration was greater than 5 mmol·L^-1, membrane fouling mitigation increased significantly in the presence of Ca²⁺ or Fe³⁺ and remained constant for Mg²⁺ with the increase of total charge concentration. The filtration resistance mitigation was arranged in the order of Fe³⁺ > Fe³⁺ + Ca²⁺ > Ca²⁺ > Mg²⁺. Three mechanisms were proposed in the presence of Fe³⁺, such as the decrease of SA concentration, change in pH, and production of hydroxide iron colloids from hydrolysis. The properties of recycled materials (filter cake) were investigated via optical microscope observation, dynamic light scattering, Fourier transform infrared, X-ray photoelectron spectroscopy (XPS), and scanning electron microscopy. The results provide further insight into UF recoveries of alginate extracted from AGS.     

颗粒赤泥吸附剂对重金属离子的吸附性能研究

以氧化铝生产产生的工业固废——赤泥为原料,采用生石灰熟化后煅烧造粒方法,制备了颗粒状赤泥吸附材料。将制得的吸附材料用于水体中Cu2+、Pb2+、Cd2+的去除。研究了吸附时间、溶液pH值、吸附剂投加量对吸附效果的影响,在吸附作用时间、pH值、投加量相同的情况下,颗粒赤泥对3种金属离子的去除效果的大小顺序为Pb2+、Cd2+、Cu2+。颗粒赤泥吸附材料对3种金属离子的等温吸附规律可分别用Langmuir等温式、Langmuir等温式和Freundlich等温式较好地进行描述。颗粒赤泥吸附剂对3种重金属离子吸附饱和容量大,达平衡时间短,具较好的吸附性能。     

Separation and recovery of gold(III) from base metal ions using melamine–formaldehyde–thiourea chelating resin

Melamine–formaldehyde–thiourea (MFT) chelating resin has been prepared. Au³⁺ ions uptake behavior and selectivity of the chelating resin were investigated by both batch and column methods. MFT resin showed higher affinity toward Au³⁺ compared with base metal ions, Cu²⁺ and Zn²⁺. The highest Au³⁺ uptake values were obtained at pH 2 and Au³⁺ adsorption capacity of the resin was calculated as 48 mg Au³⁺/g resin (0.246 mmol Au³⁺/g resin) by batch method. It was concluded that Au³⁺ ions could be selectively concentrated from the solution including Cu²⁺ and Zn²⁺ base metal ions by column method. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Preparation and adsorption properties of metal ions of crosslinked chitosan azacrown ethers

The novel azacrown ether chitosan derivatives (CCAE‐I, CCAE‐II) were prepared by reaction between crosslinked chitosan with epoxy‐activated azacrown ethers. Their structures were confirmed by elemental FTIR spectra analysis and X‐ray diffraction analysis. The adsorption and selectivity properties of the crosslinked chitosan azacrown ethers for Pb²⁺, Cu²⁺, Cr³⁺, Cd²⁺, and Hg²⁺ were also investigated. The experimental results showed that they have high adsorption capacity for Cu²⁺, Cd²⁺, and Hg²⁺. The adsorption capacity of CCAE‐II is higher than CCAE‐I for Cd²⁺ and Hg²⁺. The selectivity properties of CCAE are better than chitosan and crosslinked chitosan. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 3053–3058, 1999     

金属离子对水热法制备半水硫酸钙晶须的形貌及粒径的影响

以二水硫酸钙为原料,采用水热法制备了半水硫酸钙晶须。通过单因素实验得出制备半水硫酸钙晶须的较优工艺条件为：反应温度120℃、料浆质量分数2%、反应时间2h、搅拌速度200r/min,此时所得晶须产物平均直径2.4μm,长径比103.9,晶须呈长针状、规则统一,分散性好。探讨了K⁺、Mg²⁺、Cu²⁺、Fe³⁺、Al³⁺对较优工艺条件下制备的半水硫酸钙晶须形貌及粒径的影响,结果表明：金属离子对晶须产物形貌及粒径有显著影响。其中低浓度的Mg²⁺、Cu²⁺有助于获得小直径、高长径比的晶须产物;Al³⁺、Fe³⁺对晶须的生长有较强的抑制作用,特别是低浓度的Al³⁺、Fe³⁺使得晶须的形貌发生明显的变化,导致长径比较低;除K⁺外,金属离子浓度越高,所得晶须产物直径越大,长径比越小,并发生团聚现象,晶须由针状变为短棒状,分散性变差。同时探讨了金属离子的作用机理。     

Alkali preparation and ions detection of Ti3C2 quantum dots

In this paper, a simple lye etching method is used to directly prepare Ti₃C₂ quantum dot (QDs) without fluorine-containing groups at low lye concentration. The as-prepared Ti₃C₂ QDs have a stability fluorescent property in whole pH range of 1–14 and different fluorescence response to different types of heavy metal ions. Due to the unique and irreversible fluorescence quenching ability for Cr³⁺, Ti₃C₂ QDs can be used to detect Cr³⁺ with a low detection limit of 30 mM. Along with the high fluorescent selectivity and stability in pH = 1–14, Ti₃C₂ QDs is a great application prospect as Cr³⁺ ion detection probes in sewage disposal.     

镁铝离子共存硅酸体系的聚合行为

通过对镁铝离子共存硅酸体系中硅酸胶凝时间、单硅酸聚合反应速率以及凝胶热性能的研究,得出：在pH<;4的微酸性条件下,硅酸体系的胶凝时间随镁铝离子共存浓度的增大而减小,且铝离子在对硅酸体系的促凝过程中起主要作用。镁铝离子共存硅酸体系的单硅酸反应速率常数比不含金属离子硅酸体系的有所增大,计算得出MA_0.1+0.1硅酸体系的单硅酸平均速率常数为：k₀=7.28×10^-4,k₁=5.62×10^-4。镁铝离子共存硅酸体系凝胶的晶化转变温度与晶型转变温度,相较于不含金属离子硅酸体系的均有所降低,根据热重曲线计算出MA_0.1+0.1硅酸体系水合二氧化硅的化学式为：SiO₂·0.556 H₂O。     

Effects of some ions on ion-selectivity of ferrous sulfide film

The ion-selectivity of ferrous sulfide film formed on a cellulose sheet was determined by measuring the film potentials in neutral chloride solution. The results show that ferrous sulfide film is a bipolar film consisting of an inner cation-selective layer and an outer anion-selective layer. This kind of film structure can accelerate the localized corrosion of steel. The influence of some anions, cations and imidazoline corrosion inhibitor on ion-selectivity of the film was also investigated. The ion-selectivity of the film is altered from bipolar to anion-selective with the adsorption of Ca²⁺, Mg²⁺ and Ba²⁺ ions, or to cation-selective with the adsorption of MoO₄^2-, PO ₄^3-and imidazoline inhibitor. Potentiodynamic polarization, AC impedance technology, and the weight-loss method were used to understand the relationship between the ion-selectivity and corrosion behaviors of steel in sulfide-containing solution.     

Adsorption kinetics of cadmium ions onto powdered corn cobs

Environmental pollution caused by the presence of toxic materials such as cadmium is becoming global problem and concern. This paper presents a report on kinetics of Cd²⁺ removal from aqueous solutions through adsorption using powdered corn cobs (PCC). Corn cobs were collected from a selected location, washed to remove sand, air dried, ground and sieved into different particle sizes. The selected properties of PCC were determined using acid digestion method. Adsorption capacities through kinetics of Cd²⁺ removal from synthetic solutions, typical raw water and domestic‐institutional wastewater were studied. Effects of pH, PCC particle size, initial concentration of Cd²⁺ and temperature on adsorption capacities were monitored through pseudo first‐ and second‐order models, Elovich and intraparticle diffusion models to present adsorption rate parameters. The study revealed that PCC contained 86.89% volatile solids, had 4.56% acid solubility, 0.52 water solubility and 2.33% ash content. PCC removed Cd²⁺ from aqueous solutions (synthetic, raw water, and wastewater). The relationship between time and concentration of Cd²⁺ remaining in the solution followed exponential functions with squared correlation coefficient ranging from 0.9928 to 0.9993, 0.8701 to 0.9284, and 0.8514 to 0.9290 for synthetic solution, raw water, and typical domestic‐institutional wastewater, respectively. Mechanism of cadmium adsorption onto PCC was in two separate stages linear portions in the first parts, while the final parts are curves indicating intraparticle diffusion. It was concluded that PCC is an effective adsorbent for Cd²⁺ removal. The estimated production cost was 0.068 USD as against 0.50, 2.12, and 3.12 USD for producing adsorbents from empty fruit bunches; pencom shell and sugar cane based activated carbons, respectively.     

用改性粘土的吸附混凝去除Zn~(2+)

用凹凸棒土或膨润土制备 5种吸附剂 ,分别与一种混凝剂连用以治理含锌电镀废水。探讨最佳的吸附条件和过程机理。结果表明废水 pH值对锌去除率影响是值得注意的。当Zn2 + 离子初始质量浓度为 5 15 0mg/L时 ,最佳pH值为 9.0 ,改性膨润土用量 1g/L时 ,锌和色度去除率高达 99.8%以上。本法比传统的方法 ,如单纯中和法和沉淀法 ,要好得多