矩形通道内冲孔矩形小翼涡流发生器的流动换热特性

雷诺数Re=214～10 703时,通过数值模拟方法对布置有冲孔和无孔的两种矩形小翼涡流发生器的矩形通道进行了传热和流阻特性的研究。计算结果表明:在低雷诺数下,冲孔矩形小翼涡流发生器的传热因子j值与无孔矩形小翼涡流发生器相差不大,而在高雷诺数下,冲孔涡流发生器的传热因子j值略低于无孔涡流发生器,大约低1.03%～3.05%。在相同的雷诺数下,无孔矩形小翼涡流发生器的阻力因子f大于冲孔涡流发生器,而且随着雷诺数的增大二者的差距也越来越大。通过对比综合性能指标可知,两种通道的综合性能指标均随着雷诺数的增加而减小,而且冲孔矩形小翼涡流发生器的综合性能要优于无孔矩形小翼涡流发生器。     

加涡产生器的管片式换热器换热与阻力特性的数值研究

通过数值模拟的方法,研究了小翼式涡产生器对错排圆管管片式换热芯子换热与阻力特性的影响,比较了光板与加涡产生器强化板芯的速度场、横向平均Nu数以及平均对流换热系数、阻力系数的变化规律,为进一步提高其换热性能、改进翅片结构、设计新型换热器提供了理论依据。     

Transversal tube pitch effects on local heat transfer characteristics of the flat tube bank fin mounted vortex generators and their sensitivity to nonuniform temperature of the fin

The tube bank fin is commonly used to increase the area of the heat transfer surface with a small heat transfer coefficient of a heat exchanger. If vortex generators (VGs) are punched on the fin surface, the heat transfer performance of the fin can be improved. This paper focused on the effect of transversal tube pitch on the local heat transfer performance of the three-row flat tube bank fin mounted with VGs. On the fin surface, constructing the flow channel but without mounted VGs, the transversal tube pitch was greater, and the span averaged Nusselt number downstream was larger because fewer interactions of vortices would be generated from different VGs located upstream. When the area goodness factor was used as the criteria on the condition of one tube unit of heat exchanger for commonly used fin materials and fin thickness, the transversal tube pitch has considerable effect on the heat transfer enhancement of VGs. Large transversal tube pitch is more sensitive to fin material than to fin thickness.     

Turbulent heat transfer enhancement in a triangular duct using delta‐winglet vortex generators

The augmentation of convective heat transfer of a turbulent flow using delta‐winglet vortex generators (VG) in a triangular duct was experimentally investigated. Two side walls of the heated test section are electrically heated with a constant heat flux while the lower wall is indirectly heated. Single, double, and triple pairs of VG are utilized. Each pair of VG was punched on one wall of the test duct. The effects of the number of VG pairs, the VG angle of attack, the VG location from the leading edge of the test duct, the VG geometry, and Reynolds number are examined in this paper. The results indicate that the Nusselt number and friction factor are relatively proportional to the size, number, and the inclination angle of the VG. The Nusselt number increases and the friction factor decreases as the Reynolds number increases. The present results were compared with the available literature and they show good agreement. Correlation equations of Nusselt number and friction factor for turbulent flow are developed, for the cases studied, as a function of Reynolds number and VG angle of attack. © 2011 Wiley Periodicals, Inc. Heat Trans Asian Res; Published online in Wiley Online Library ( wileyonlinelibrary.com/journal/htj ). DOI 10.1002/htj.20382     

通道内设置涡发生器时的强化传热研究现状与展望

随着强化传热技术的研究发展，各种形式的涡发生器的强化传热效果日益受到国内外的重视。文章比较全面地介绍了近年来国内外关于通道内布置各类涡发生器时的强化传热研究状况，并提出了有待进一步开展的研究内容。     

Heat transfer enhancement by using a rectangular wing vortex generator on the triangular shaped fins of a plate‐fin heat exchanger

The present numerical analysis pertains to the heat transfer enhancement in a plate‐fin heat exchanger employing triangular shaped fins with a rectangular wing vortex generator on its slant surfaces. The study has been carried out for three different angles of attack of the wing, i.e., 15°, 20° and 26°. The aspect ratio of the wing is not varied with its angle of attack. The flow considered herein is laminar, incompressible, and viscous with the Reynolds number not exceeding 200. The pressure and the velocity components are obtained by solving the continuity and the Navier– Stokes equations by the Marker and Cell method. The present analysis reveals that the use of a rectangular wing vortex generator at an attack angle of 26° results in about a 35% increase in the combined spanwise average Nusselt number as compared to the plate‐triangular fin heat exchanger without any vortex generator. © 2010 Wiley Periodicals, Inc. Heat Trans Asian Res; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/htj.20285     

纵向涡强化竖直平板自然对流换热的实验研究

对纵向涡强化竖直平板自然对流换热进行了实验研究。结果表明，在一定的Rayleigh数范围内，直角三角翼纵向涡发生器的攻角、翼高、翼宽等几何参数是影响强化换热的主要因素。存在最佳攻角；宽高比一定时，翼高和翼宽的变化会影响换热的效果。发现在直角三角翼阵列中前排直角三角翼产生的纵向涡可以强化后排直角三角翼纵向涡的换热。将直角三角翼与矩形低肋换热表面的性能作了对比性实验，在其他条件相同的情况下，直角三角翼强化换热的效果优于矩形低肋。     

Heat transfer enhancement of turbulent duct flow by vortex generators attached to a large eddy break-up manipulator

An experimental study was conducted to investigate the characteristics of wall heat transfer and momentum loss for turbulent duct flow disturbed by insertion of a complicated body composed of a Large Eddy Break-Up (LEBU) plate and winglet-type vortex generators. It was found that the LEBU plate reduces the wall heat transfer in the region downstream of the insertion position and that this suppression of heat transfer could be recovered by attaching vortex generators to the LEBU plate, i.e., conspicuous heat transfer enhancement was achieved over a large streamwise distance. The spatial distribution of the heat transfer coefficient obtained shows the same features as that observed in a previous study of a flat plate turbulent boundary layer. Therefore, the flow and thermal field structure of the turbulent duct flow downstream of the inserted body should be basically the same as those in the same region of the turbulent boundary layer. The effect of a notch, open in the LEBU plate behind the vortex generator, on heat transfer and pressure drop was also examined. The notch simulates the hole of the LEBU plate to be produced in a practical application when a vortex generator is produced by punching from the original plain LEBU plate. It was found that a vortex generator with an open notch works best in augmenting the wall heat transfer and also in suppressing the increase of momentum loss. © 1999 Scripta Technica, Heat Trans Asian Res, 28(3): 189–200, 1999     

多种纵向涡发生器配置方案流动换热的数值模拟

为了深入挖掘三角翼纵向涡发生器在两个相对壁面布置的强化换热潜力,采用数值模拟方法,在雷诺数3 000～18 000的范围内研究了5种纵向涡发生器配置的流动换热情况,配置方式包括单面布置的共同上、下流配置,双面布置的共同上、下流配置,以及混合配置。结果表明：纵向涡可以很好地提高场协同效果,换热强度不完全取决于通道中的二次流强度,还取决于通道中的场协同性;在所有配置中,混合配置具有最高的二次流强度、最佳的场协同效果以及换热性能,可以将光滑通道的Nu提高28.3%～35.3%;另外4种配置可分别将光滑通道的Nu提高21.4%～32.0%,20.0%～29.2%,26.3%～34.3%和23.7%～28.0%;建议选用Re<6 000范围内的混合配置,此时其具有1.03～1.10的综合换热因子以及1.32～1.35的Nu/Nu₀。     

Flow visualization of wave-type vortex generators having inline fin-tube arrangement

This study presents visual observation of enlarged fin-and-tube heat exchangers with and without the presence of vortex generators. Three samples of fin-and-tube heat exchanger having inline arrangements are examined, including one plain fin and two wave-type vortex generators. For plain fin geometry at Re=500, the horseshoe vortex generated by the tube row is not so pronounced, and a very large secondary flow circulation is seen between the first and second row. This flow re-circulation phenomenon is almost disappeared with the presence of proposed vortex generators. The presence of vortex generators significantly increase the vortrical motions of the horseshoe vortices hitting on the tubes. A much better mixing characteristics is seen by introducing the vortex generators. The frictional penalty of the proposed vortex generators are about 25-55% higher than that of the plain fin geometry. The penalty of pressure drops of the proposed vortex generators relative to plain fin geometry is relatively insensitive to change of Reynolds number.     

Experimental study on heat transfer enhancement in the vertical nature convection by using delta‐winglet longitudinal vortex generators

This paper focuses on the study of heat transfer enhancement in natural vertical convection by using delta‐winglet longitudinal vortex generators. In the experimental range of Rayleigh numbers, the effect of attack angle, height, and width of the winglet of longitudinal vortex generator (LVG) on heat transfer performance was experimentally investigated. The results showed that there was an optimal attack angle and that the height and width can affect the heat transfer. In terms of array performance, it was shown that initial arrays could enhance the performance of later arrays. Moreover, the effects of LVG and low rectangular fins were compared. The results showed that the effect of LVGs was greater than that of low rectangular fins. © 2006 Wiley Periodicals, Inc. Heat Trans Asian Res, 35(6): 402–409, 2006; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/htj.20126     

Heat transfer augmentation in a plate‐fin heat exchanger using a rectangular winglet

This study presents numerical computation results on laminar convection heat transfer in a plate‐fin heat exchanger, with triangular fins between the plates of a plate‐fin heat exchanger. The rectangular winglet type vortex generator is mounted on these triangular fins. The performance of the vortex generator is evaluated for varying angles of attack of the winglet i.e., 20, 26, and 37° and Reynolds number 100, 150, and 200. The computations are also performed by varying the geometrical size and location of the winglet. The complete Navier–Stokes equation and the energy equation are solved by the (Marker and Cell) MAC algorithm using the staggered grid arrangement. The constant wall temperature thermal boundary conditions are considered. Air is taken as the working fluid. The heat transfer enhancement is seen by introducing the vortex generator. Numerical results show that the average Nusselt number increases with an increase in the angle of attack and Reynolds number. For the same area of the LVG, the increase in length of the LVG brings more heat transfer enhancement than increasing the height. The increase in heat transfer comes with a moderate pressure drop penalty. © 2010 Wiley Periodicals, Inc. Heat Trans Asian Res; Published online in Wiley Online Library ( wileyonlinelibrary.com ). DOI 10.1002/htj.20318     

带短肋翅片管的强化传热机理研究

同时对普通翅片管和带有两个短肋的翅片管在均匀流场中、不同雷诺数下进行了流场和传热的数值模拟,分析了带有短肋的翅片管强化传热的机理。结果表明,由于翅片上带有的短肋和短肋后面的开孔,减少了翅片管管后流动的死滞区,提高了局部地区流体的流速,增加了扰动,从而起到了强化传热的作用。取入口雷诺数为20000时,加装短肋后可使总传热量增加5.1%,平均表面传热系数增加23.56%。随着雷诺数的增加,总换热量增加,强化传热效果也增强。     

纵向涡发生器强化传热管的实验研究

介绍了一种高效强化传热管,沿传热管内壁轴向均匀排布三列成对的纵向涡发生器,在常壁温条件下进行加热空气在管内流动的冷却实验,研究强化传热管的传热和阻力特性。结果表明,在过渡流区管内置纵向涡发生器的强化传热大大增强,Nu增大为光管的2.02.3倍,阻力损失也相应有所增加,提出一种比较优化的发生器的形状设计,探讨了传热和阻力随设置间距变化的规律。     

Experimental study on heat transfer enhancement on natural convection in a vertical plate by using longitudinal vortex generators arranged in rows

Longitudinal vortices are capable of producing beneficial effects in heat transfer enhancement. Experiments in natural convection heat transfer enhancement were done on a vertical flat heating plate using delta‐winglet longitudinal vortex generators (LVGs) arranged in rows. In an experimental range of Rayleigh number, the height and width of the winglet of the longitudinal vortex generator (LVG), the array form of the longitudinal vortex generators on the heat transfer performance were experimentally investigated, and the best height of the winglet of the longitudinal vortex generator was obtained. The results showed the change of the array form of the longitudinal vortex generators could affect the heat transfer effect. Finally by arranging some longitudinal vortex generator arrays with the appropriate interval, the whole heat transfer effect of the interval could reach a prime value. © 2006 Wiley Periodicals, Inc. Heat Trans Asian Res, 35(5): 351–358, 2006; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/htj.20119     

多排纵向涡发生器强化竖直平板自然对流换热的实验研究

对多排纵向涡发生器对竖直平板自然对流的强化效果进行了研究。结果表明，在一定Rayleigh数范围内，直角三角翼纵向涡发生器的翼高、翼宽以及多排布置的阵列方式是影响强化换热的主要因素。在高宽比一定的情况下，存在最佳翼高。发现多排布置时LVG阵列方式的不同会影响换热效果；且要使得整个板的强化换热效果达到最佳，应选择沿竖直发热板长度方向间隔的布置多排LVG，并适当拉大间隔距离。     

椭圆管散热器传热及阻力性能试验研究

对空气横掠片距不相等的叉排椭圆翅片管散热器的传热及阻力性能进行了试验研究,得到试件在一系列工况下的传热与管外流动阻力数据,并对试验数据进行分析计算,从总传热系数K中分离出管外空气侧的对流换热系数h,给出有工程应用价值的管外换热准则关系式及管外阻力准则关系式。认为椭圆管管外的平均换热效果优于圆管。在相同的流通截面积下椭圆管传热周边较长,换热面积相应增加,因此结构上允许布置得更紧凑。     

Numerical analysis on heat transfer enhancement by longitudinal vortex based on field synergy principle

Three-dimensional numerical simulation results are presented for a fin-and-tube heat transfer surface with vortex generators. The effects of the Reynolds number (from 800 to 2 000) and the attack angle (30° and 45°) of a delta winglet vortex generator are examined. The numerical results are analyzed on the basis of the field synergy principle to explain the inherent mechanism of heat transfer enhancement by longitudinal vortex. The secondary flow generated by the vortex generators causes the reduction of the intersection angle between the velocity and fluid temperature gradients. In addition, the computational evaluations indicate that the heat transfer enhancement of delta winglet pairs for an aligned tube bank fin-and-tube surface is more significant than that for a staggered tube bank fin-and-tube surface. The heat transfer enhancement of the delta winglet pairs with an attack angle of 45° is larger than that with an angle of 30°. The delta winglet pair with an attack angle of 45° leads to an increase in pressure drop, while the delta winglet pair with the 30° angle results in a slight decrease. The heat transfer enhancement under identical pumping power condition for the attack angle of 30° is larger than that for the attack angle of 45° either for staggered or for aligned tube bank arrangement. Translated from Journal of Xi’an Jiao Tong University, 2006, 40(7): 757–761 [译自: 西安交通大学学报]     

Flow visualization of annular and delta winlet vortex generators in fin-and-tube heat exchanger application

This study presents flow visualization and frictional results of enlarged fin-and-tube heat exchangers with and without the presence of vortex generators. Two types of vortex generators and a plain fin geometry were examined in this study. For plain fin geometry at Re=500, the horseshoe vortex generated by the tube row is not so pronounced, and the horseshoe vortex separates into two streams as it flows across the second row and consequently loses its vortical strength. This phenomenon may supports the “maximum phenomenon” in low Reynolds number region reported by previous studies. With the presence of annular vortex generator, the presence of a pair of longitudinal vortices formed behind the tube is seen. The strength of the counter-rotating vortices increases with the annular height and the strength of the longitudinal vortices is so strong that may swirl with the horseshoe vortices and other flow stream. For the same winlet height, the delta winlet shows more intensely vortical motion and flow unsteadiness than those of annular winlet. This eventually leads to a better mixing phenomenon. However, it is interesting to know that the corresponding pressure drops of the delta winlet are lower than those of annular winlet. Compared to the plain fin geometry, the penalty of additional pressure drops of the proposed vortex generators is relatively insensitive to change of Reynolds number.     

Numerical study of fluid flow and heat transfer in a flat-plate channel with longitudinal vortex generators by applying field synergy principle analysis

Three dimensional numerical simulations are performed on laminar heat transfer and fluid flow characteristics of a flat-plate channel with longitudinal vortex generators (LVGs). The effects of two different shaped LVGs, rectangular winglet pair (RWP) and delta winglet pair (DWP) with two different configurations, common-flow-down (CFD) and common-flow-up (CFU), are studied. The numerical results indicate that the application of LVGs effectively enhances heat transfer of the channel. According to the performance evaluation parameter, (Nu/Nu₀)/(f/f₀), the channel with DWP has better overall performance than RWP; the CFD and CFU configurations of DWP have almost the same overall performance; the CFD configuration has a better overall performance than the CFU configuration for RWP. The basic mechanism of heat transfer enhancement by LVGs can be well described by the field synergy principle.