氨化Si基Ga2O3/V薄膜制备GaN纳米线

为了制备高质量的GaN纳米结构,采用磁控溅射技术先在硅衬底上制备Ga2O3/V薄膜,然后在流动的氨气中进行氨化反应,成功制备出GaN纳米线.采用X射线衍射(XRD)、傅里叶红外吸收光谱(FTIR)、扫描电子显微镜(SEM)和透射电子显微镜(TEM)对样品进行分析.研究结果表明,采用此方法得到了六方纤锌矿结构的GaN纳米线,且900℃时制备的纳米线质量最好,直径在60nm左右,长度达到十几微米.     

氨化Si基Ga2O3/Co薄膜制备GaN纳米线

采用磁控溅射技术先在硅衬底上制备Ga2O3/Co薄膜,然后在900℃时于流动的氨气中进行氨化反应制备GaN薄膜.X射线衍射(XRD)、傅立叶红外吸收光谱(FTIR)、选区电子衍射(SAED)和高分辨透射电子显微镜(HRTEM)的分析结果表明,采用此方法得到了六方纤锌矿结构的GaN单晶纳米线.通过扫描电镜(SEM)观察发现纳米线的形貌,纳米线的尺寸在 50～200nm之间.     

化学气相沉积法制备GaN纳米线和纳米棒

采用浸渍法在未抛光的硅衬底上涂抹一层NiCl2薄膜,通过化学气相沉积法(CVD)制备出高质量的GaN纳米线和纳米棒.X射线衍射(XRD)、傅立叶红外吸收光谱(FTIR)、选区电子衍射(SAED)和高分辨透射电子显微镜(HRTEM)的分析结果表明,采用此方法得到了六方纤锌矿结构的GaN单晶纳米线.通过扫描电镜(SEM)观察发现纳米线的形貌,纳米线的直径在50～200nm之间,纳米棒的直径在200～800nm之间.     

Si基Au催化合成镁掺杂GaN纳米线

通过一种新奇的方法在硅衬底上成功地合成了掺杂镁的氮化镓纳米线,用金属镁粉末作为掺杂源,然后在900℃时于流动的氨气中进行氨化Ga2P3薄膜制备GaN纳米线.X射线衍射(XRD)、扫描电镜(SEM)、透射电子显微镜(TEM)、选区电子衍射(SAED)和能量弥散X射线谱(EDX)的分析结果表明,采用此方法得到的GaN纳米线为六方纤锌矿结构,纳米线的直径大约在60～100nm之间,纳米线的长约十几个微米.EDX分析表明纳米线掺杂了镁.室温下以325nm波长的光激发样品表面,发现由于镬的掺杂使GaN的发光峰有较大的蓝移.最后,简单讨论了GaN纳米线的生长机制.     

氨化Si基Ga2O3/Ti制备GaN纳米线

采用磁控溅射技术先在硅衬底上制备Ga2O3/Ti薄膜,然后在950℃时于流动的氨气中进行氨化反应制备GaN薄膜.X射线衍射(XRD)、傅立叶红外吸收光谱(FTIR)、选区电子衍射(SAED)和高分辨透射电子显微镜(HRTEM)的结果表明采用此方法得到了六方纤锌矿结构的GaN单晶纳米线.通过扫描电镜(SEM)观察发现纳米线的形貌,纳米棒的尺寸在50～150nm之间.     

氨化Ga_2O_3/Pd/Sapphire薄膜制备GaN纳米线

利用金属元素钯作催化剂,采用磁控溅射后氨化法,成功的在Sapphire衬底上制备出GaN纳米线。X射线衍射和X射线光电子能谱研究显示合成的纳米线具有六方纤锌矿GaN结构。通过扫描电子显微镜,透射电子显微镜和高分辨透射电子显微镜观察分析得出GaN纳米线为单晶结构,其纳米线的直径约为10～60nm,长度达几十个微米。室温下以325nm波长的光激发样品表面,发现GaN带边发光峰有较弱的蓝移。最后简单讨论了GaN纳米线的生长机制。     

氨化Ga2O3/TiO2/Si薄膜制备GaN纳米线

为了制备高质量的GaN纳米结构,采用磁控溅射技术先在硅衬底上制备Ga2O3／TiO2薄膜,然后在950℃时于流动的氨气中进行氨化反应,成功制备出GaN纳米线．采用X射线衍射（XRD）、傅里叶红外吸收光谱（FTIR）、扫描电子显微镜（SEM）和高分辨透射电子显微镜（HRTEM）对样品进行分析．研究结果表明,采用此方法得到了六方纤锌矿结构的GaN单晶纳米线,纳米线的直径在100～400nm,纳米线的长度在3～10μm．     

模板法制备CuO分叉纳米线

通过3次阳极氧化制备具有分叉结构的氧化铝模板,在氧化铝模板的纳米孔洞中,用电化学方法沉积铜纳米线,经过500℃、30h氧化处理,成功制备出具有分叉结构的CuO纳米线.分别用扫描电子显微镜(SEM)、透射电子显微镜(TEM)和X射线衍射仪(XRD)对样品的形貌和晶体结构进行了表征测试.SEM观察结果氧化铝模板的纳米孔洞相互平行、分布均匀,枝干的孔心距约为120nm,枝叉的孔心距约为70nm.TEM观察显示纳米线各部分粗细均匀.样品的XRD分析表明分叉纳米线阵列的晶体结构为CuO.     

复合锌镍纳米线结构和磁性研究

采用直流电化学沉积方法,在多孔阳极氧化铝模板纳米孔洞中制备出直径约90nm,长度超过10μm的金属Ni/Zn纳米线有序阵列.通过扫描电子显微镜(SEM),透射电子显微镜(TEM),原子力显微镜(AFM),X射线衍射仪(XRD),振动样品磁强计(VSM)对模板及所制备的样品进行形貌、结构及相关性能的表征和测试.结果表明所制备的Ni/Zn纳米线具有沿[111]方向择优生长特性,易磁化方向沿纳米线长轴方向.     

金属钨纳米线阵列的制备

用气相方法在较低的温度(900℃)下在单晶硅基片表面制备出金属钨的单晶纳米线阵列,用扫描电子显微镜(SEM)、透射电子显微镜(TEM)和X-ray衍射(XRD)等手段对其进行了分析和表征.结果表明:在900℃制备的阵列单晶钨纳米线沿〈111〉方向生长,具有bcc结构,直径约为150 nm,长度为10-30μm.     

Insertion of triangulated surfaces into a meccano tetrahedral discretization by means of mesh refinement and optimization procedures

In this paper, we present a new method for inserting several triangulated surfaces into an existing tetrahedral mesh generated by the meccano method. The result is a conformal mesh where each inserted surface is approximated by a set of faces of the final tetrahedral mesh. First, the tetrahedral mesh is refined around the inserted surfaces to capture their geometric features. Second, each immersed surface is approximated by a set of faces from the tetrahedral mesh. Third, following a novel approach, the nodes of the approximated surfaces are mapped to the corresponding immersed surface. Fourth, we untangle and smooth the mesh by optimizing a regularized shape distortion measure for tetrahedral elements in which we move all the nodes of the mesh, restricting the movement of the edge and surface nodes along the corresponding entity they belong to. The refining process allows approximating the immersed surface for any initial meccano tetrahedral mesh. Moreover, the proposed projection method avoids computational expensive geometric projections. Finally, the applied simultaneous untangling and smoothing process delivers a high‐quality mesh and ensures that the immersed surfaces are interpolated. Several examples are presented to assess the properties of the proposed method.     

Certification Institutions Expected to Update and Transfer Information on Present Standards

Standards are the basis for production enterprises to organize production, ex-factory inspection, trade (delivery) and technical exchanges, product certification, quality arbitration and supervision.……     

From Industry 4.0 to Research 4.0. Development of High Performance Fibers in the Light of Digitization

We associate a variety of innovations with the term ＂Industry 4.0＂. The pioneer of many 4.0 modifications forms the basisfor the trend towards the integrated di...     

Flow calorimeter for enthalpy increment measurements on condensed gases

A flow calorimeter for enthalpy increment measurements on condensed gases is presented. A better knowledge of the properties of the liquefied natural gas is needed, and therefore a liquid loop has been designed for our flow calorimeter. The fluid loop in the calorimeter is designed in order to avoid the two-phase region, since two phases would give compositional disturbances in the measurements. The avoidance of the two-phase region is made possible by increasing the pressure of the test fluid after the measurement section, then heating the fluid at super-critical pressure past the critical point. Finally, the fluid is throttled to the low-pressure gas state at the inlet condition of the compressor that circulates the fluid. To perform the pressure increase, a new cryogenic pump has been designed. To evaluate the new equipment, measurements were taken on liquid ethane over the temperature range 146–256 K at pressure between 0.9 and 5.1 MPa.     

Refrigerators Enter a New Era of Health Preservation Frestech initiates the establishment of China's first standard for household sterilization refrigerators

On November 30, 2007, the China Association for Standardization (CAS) held a press conference at Beijing Diaoyutai State Guest House. Leaders from the China Household Electric Appliance Research Institute, the China Household Electric Appliance Association, and the China Consumers' Association attended and made speeches.……     

Roman iron and steel: A review

ABSTRACT

The production of ferrous metal increased during the Roman Late Republican period, Principate and Empire. The direct bloomery process was used to extract the metal from its ores using slag-tapping and slag-pit furnaces. The fuel was charcoal and an air blast was introduced by bellows-operated tuyères. Iron formed as a bloom, often as a spongy mass of metal, which contained impurities from the smelting process, including unreacted ore, fuel, slag and fragments from the furnace walls, while the metal was often inhomogeneous with varied carbon contents. Blooms were either smithed directly into bars or ingots or they were broken up, which also allowed the removal of gross impurities and a selection of pieces with similar properties to be made. These could then be forge-welded together and formed into characteristically shaped ingots. Making steel in the furnace seems to have been achieved: it depended on the ore and the furnace and conditions within it. Surface carburization was also carried out. Iron and steel were used extensively in construction and for tools and weapons. Fire welding was often used to add pieces of steel to make the edges of tools and weapons, which could be heat-treated by quenching to harden them.     

Optimum-Simulation von Ernteprozessen

Zusammenfassung Bei der Gestaltung von Ernteprozessen — beispielsweise des Prozesses Mähdrusch, Körnertransport und -abnahme — als transportverbundene Fließarbeitsverfahren mit mindestens zwei verschiedenen Arbeitsmitteln gibt es einen großen Optimierungsspielraum. Solche Prozesse sind mehrstufige Bedienungsprozesse mit gemischter Anordnung der Bedienungseinrichtungen. Außerdem besitzen sie stark ausgeprägte räumliche Aspekte. Es wird vor allem gezeigt, welche Merkmale solcher Prozesse in Simulationsmodellen abgebildet sein müssen, welche Zielgrößen in Abhängigkeit von welchen Einflußgrößen unter Berücksichtigung welcher Prozeßbedingungen ermittelt werden sollten und wie der Bewertungsprozeß zur Ermittlung der gewünschten Informationen gestaltet werden muß.     

A study of centrifugal cast high boron high speed steel

In the present study a high‐boron high speed steel (HSS) roll material was designed. Many expensive alloy elements have been substituted by cheap boron alloy, and high‐boron high speed steel roll has been manufactured by centrifugal casting method. The microstructures, mechanical properties and wear resistance of centrifugal casting high‐boron high speed steel roll have been investigated by optical microscopy (OM), scanning electron microscopy (SEM), and X‐ray diffraction (XRD) analysis, hardness test, impact test and wear test. The results indicated that the solidification microstructures of high‐boron high speed steel roll consisted of M₂(B,C), (W,Mo)₂(B,C), M₃(B,C), M₂₃(B,C)₆ type borocarbides and martensite, a small amount of retained austenite. Borocarbides were continuously distributed over the grain boundary. After quenching from 1050 °C, local broken network appeared in partial borocarbides, and fine secondary borocarbide precipitated from the matrix. After tempering from 525 °C, the amount of precipitated borocarbide increased significantly. After heat treatment, the hardness of high‐boron high speed steel roll excelled 60 HRC, and its impact toughness excelled 8.0 J/cm². The single groove steel rolling amount of high‐boron high speed steel rolls increases by 500% than that of bainite cast iron roll, when the rolls are used in K₁ mill housing of bar mill.     

Thixotropy of Systems with Shear Thinning and Plastic Flow Behavior

The definition of the thixotropy is a decrease in viscosity with time in shear and a subsequent recovery of viscosity after the shear deformation is removed.We ...