A 6-bit 800-MS/s Pipelined A/D Converter With Open-Loop Amplifiers

A 6-bit 800-MS/s pipelined A/D converter (ADC) achieves SNDR and SFDR of 33.7 dB and 47.5 dB, respectively. Employing voltage-mode open-loop amplifiers in gain stages, global gain control techniques, and two-bank-interleaved architecture, the proposed pipelined A/D converter relaxes stringent design tradeoffs between speed and power. Fabricated in a 0.18-mum CMOS technology, the ADC consumes 105 mW from a 1.8-V power supply while the active area is only 0.5 mm²     

一种12位50MS/s CMOS流水线A/D转换器

采用TSMC 0.18μm 1P6M工艺设计了一个12位50 MS/s流水线A/D转换器（ADC）。为了减小失真和降低功耗,该ADC利用余量增益放大电路（MDAC）内建的采样保持功能,去掉了传统的前端采样保持电路;采用时间常数匹配技术,保证输入高频信号时,ADC依然能有较好的线性度;利用数字校正电路降低了ADC对比较器失调的敏感性。使用Cadence Spectre对电路进行仿真。结果表明,输入耐奎斯特频率的信号时,电路SNDR达到72.19 dB,SFDR达到88.23 dB。当输入频率为50 MHz的信号时,SFDR依然有80.51 dB。使用1.8 V电源电压供电,在50 MHz采样率下,ADC功耗为128 mW。     

A 600-MS/s 5-bit pipeline A/D converter using digital reference calibration

The design of a 600-MS/s 5-bit analog-to-digital (A/D) converter for serial-link receivers has been investigated. The A/D converter uses a closed-loop pipeline architecture. The input capacitance is only 170 fF, making it suitable for interleaving. To maintain low power consumption and increase the sampling rate beyond the amplifier settling limit, the paper proposes a calibration technique that digitally adjusts the reference voltage of each pipeline stage. Differential input swing is 400 mV/sub p-p/ at 1.8-V supply. Measured performance includes 25.6 dB and 19 dB of SNDR for 0.3-GHz and 2.4-GHz input frequencies at 600 MS/s for the calibrated A/D converter. The suggested calibration method improves SNDR by 4.4 dB at 600 MS/s with /spl plusmn/0.35 LSB of DNL and /spl plusmn/0.15 LSB of INL. The 180 /spl times/ 1500 /spl mu/m/sup 2/ chip is fabricated in a 0.18-/spl mu/m standard CMOS technology and consumes 70 mW of power at 600 MS/s.     

A 150 MS/s 133$~mu$W 7 bit ADC in 90 nm Digital CMOS

In recent years the energy efficiency of A/D converters has been improved significantly. Only 5 years ago an energy efficiency of 1 pJ/conversion step was considered state-of-the-art. Now power efficiencies are reported in fJ/conversion step. In this paper two new converter techniques are presented that further improve upon reported energy efficiencies of A/D converters. The first technique implements the quantization with a comparator-based asynchronous binary search (CABS). The second technique implements the SAR control algorithm on the comparators (SAR-CC) that are also used to do the quantization. Both these techniques have been applied in a fully dynamic 7 bit A/D converter that uses a two-step 1b coarse and 6b fine architecture . The 1b coarse converter is implemented using the SAR-CC principle, the 6b fine converter is implemented using the CABS principle. The 7 bit prototype implementation in 90 nm digital CMOS on a 1 V supply achieves 6.4ENOB, 40 dB SNDR at 150 MS/s consuming 133$~mu{hbox {W}}$ giving 10 fJ/conversion step energy efficiency (FOM). A second prototype implementing a stand-alone 6b CABS converter (the sub-A/D converter of the 7 bit converter) achieves 32 dB SNDR at 250 MS/s with 140$~mu{hbox {W}}$ of power consumption, which results in a FOM of 15 fJ/conversion step.      

A 6-GSamples/s multi-level decision feedback equalizer embedded in a 4-bit time-interleaved pipeline A/D converter

A 4-bit 6-GS/s pipeline A/D converter with 10-way time-interleaving is demonstrated in a 0.18-/spl mu/m CMOS technology. The A/D converter is designed for a serial-link receiver and features an embedded adjustable single-tap DFE for channel equalization. The ISI subtraction of the DFE is performed at the output of each pipeline stage; hence the effective feedback delay requirement is relaxed by 6/spl times/. Code-overlapping of the 1.5-bit pipeline stage along with digital error correction is used to absorb and remove the remainder of the ISI. The measured A/D converter performance at 6-GSamples/s shows 22.5 dB of low-frequency input SNDR for the calibrated A/D converter with /spl plusmn/0.25 LSB and /spl plusmn/0.4 LSB of INL and DNL, respectively. The input capacitance is 170 fF for each A/D converter. The DFE tap coefficient is adjustable from 0 to 0.25 with 6-bits of programmable weight. With a DFE coefficient of 0.2, the measured DFE performance shows 2.5 dB of amplitude boosting for a 3-GHz input sinusoid. The 1.8/spl times/1.6 mm/sup 2/ chip consumes 780 mW of power from a 1.8-V power supply.     

A low power 12-bit 200-kS/s SAR ADC with a differential time domain comparator

A low power 12-bit 200-kS/s SAR ADC is proposed.This features a differential time domain comparator whose offset is cancelled by using a charge pump and a phase frequency detector instead of the preamplifiers usually needed in a high resolution comparator.The proposed ADC is manufactured in 0.18-μm CMOS technology and the measured SNR and SNDR are 62.5 dB and 59.3 dB,respectively,with a power consumption of 72μW at a 200-kS/s sampling rate.The device operates with a 1.8-V power supply and achieves a FOM of 477 fJ/conversion-step.     

A 10-b, 100-MS/s CMOS A/D converter

A new architecture for a CMOS A/D converter overcomes many of the known problems in the parallel operation of multiple pipelined stages. The input signal is sampled in one channel, and after quantization to 4 b, the residue is distributed into many channels. A prototype implemented in 1-μm CMOS achieves 60 dB signal-to-noise plus distortion ratio (SNDR) at low conversion rates, with a resolution bandwidth of greater than 20 MHz. The SNDR drops by 3 dB at a 95 MHz conversion rate, and the bandwidth remains the same     

一个用于12位40-MS/s低功耗流水线ADC的MDAC电路设计

文中设计了一个用于12位40MHz采样率低功耗流水线ADC的MDAC电路.通过对运放的分时复用,使得一个电路模块实现了两级MDAC功能,达到降低整个ADC功耗的目的.通过对MDAC结构的改进,使得该模块可以达到12bit精度的要求.通过优化辅助运放的带宽,使得高增益运放能够快速稳定.本设计在TSMC0.35μmmixsignal3.3V工艺下实现,在40MHz采样频率下,以奈奎斯特采样频率满幅(Vpp=2V)信号输入,其SINAD为73dB,ENOB为11.90bit,SFDR为89dB.整个电路消耗的动态功耗为9mW.     

A 0.7-V 870-$mu$ W Digital-Audio CMOS Sigma-Delta Modulator

This paper introduces a power-efficient, chopper-stabilized switched-capacitor sigma-delta $(SigmaDelta)$ modulator that combines delayed input feedforward and single-comparator tracking multi-bit quantization to achieve high-precision, low-voltage analog-to-digital (A/D) conversion. An experimental prototype of the proposed architecture has been integrated in a 0.18-$mu{hbox {m}}$ CMOS technology. The prototype operates from a 0.7-V supply voltage with a sampling rate of 5 MSamples/sec and consumes only 870$ muhbox{W}$ of total power. The converter achieves a dynamic range of 100 dB, a peak signal-to-noise ratio (SNR) of 100 dB and a peak signal-to-noise and distortion ratio (SNDR) of 95 dB for a 25-kHz signal bandwidth.      

采用改进型1.5位/级结构的10位100MHz流水线模数转换器

介绍了一个采用改进型1.5位/级结构的10位100MHz流水线结构模数转换器.测试结果表明,模数转换器的信噪失真比最高可以达到57dB,在100MHz输入时钟下,输入信号为57MHz的奈奎斯特频率时,信噪失真比仍然可以达到51dB.模数转换器的差分非线性和积分非线性分别为0.3LSB和1.0LSB.电路采用0.18μm混合信号CMOS工艺实现,芯片面积为0.76mm2.     

A 6-bit 600-MS/s 5.3-mW Asynchronous ADC in 0.13-μm CMOS

An asynchronous analog-to-digital converter (ADC) based on successive approximation is used to provide a high-speed (600-MS/s) and medium-resolution (6-bit) conversion. A high input bandwidth (>4 GHz) was achieved which allows its use in RF subsampling applications. By using asynchronous processing techniques, it avoids clocks at higher than the sample rate and speeds up a nonbinary successive approximation algorithm utilizing a series nonbinary capacitive ladder with digital radix calibration. The sample rate of 600 MS/s was achieved by time-interleaving two single ADCs, which were fabricated in a 0.13-mum standard digital CMOS process. The ADC achieves a peak SNDR of 34 dB, while only consuming an active area of 0.12mm² and having power consumption of 5.3 mW     

一种基于电阻型数模转换器每级输出3位的6-bit 410-MS/s单通道异步逐次逼近模数转换器

该设计采用SMIC 65-nm CMOS工艺,实现了一款可应用于超宽带通信领域的单通道低功耗6位410-MS/s异步逐次逼近模数转换器(SAR ADC)。通过采用电阻型数模转换器、每级输出3位数字码字结构,以及改进的异步控制逻辑,该ADC在370-MS/s采样率时,无杂散动态范围(SFDR)达到41.95-dB,信号噪声失真比(SNDR)达到28.52-dB。在采样率为410MS/s时,该设计仍能达到40.71-dB的SFDR和30.02-dB的SNDR。通过动态比较器的使用,实现了低功耗设计。测试结果表明,在410-MS/s采样率下,电路总功耗为2.03mW,对应的品质因子(FOM)为189.17fJ/step。     

0.13 μm CMOS 60 dB SFDR的8 bit 250 MS/s模数转换器

论述了一种高速度低功耗的8位250 MHz采样速度的流水线型模数转换器(ADC).在高速度采样下为了实现大的有效输入带宽,该模数转换器的前端采用了一个采样保持放大器(THA).为了实现低功耗,每一级的运放功耗在设计过程中具体优化,并在流水线上逐级递减.在250 MHz采样速度下,测试结果表明,在1.2 V供电电压下,所有模块总功耗为60 mw.在19 MHz的输入频率下,SFDR达到60.1 dB,SNDR为46.6 dB,有效比特数7.45.有效输入带宽大于70 MHz.该ADC采用TSMC 0.13μm CMOS 1P6M工艺实现,芯片面积为800 μm×700μm.     

A Low-Power Low-Voltage 10-bit 100-MSample/s Pipeline A/D Converter Using Capacitance Coupling Techniques

This paper presents a low-power low-voltage 10-bit 100-MSample/s pipeline analog-to-digital converter (ADC) using capacitance coupling techniques. A capacitance coupling sample-and-hold stage achieves high SFDR with 1.0-V supply voltage at a high sampling rate. A capacitance coupling folded-cascode amplifier effectively saves the power consumption of the gain stages of the ADC in a 90-nm digital CMOS technology. The SNDR and the SFDR are 55.3 dB and 71.5 dB, respectively, and the power consumption is 33 mW     

A power-efficient 10-bit 40-MS/s sub-sampling pipelined CMOS analog-to-digital converter

This paper presents a 10-bit 40-MS/s pipelined analog-to-digital converter (ADC) in a 0.13-μm CMOS process for subsampling applications. A simplified opamp-sharing scheme between two successive pipelined stages is proposed to reduce the power consumption. For subsampling, a cost-effective fast input-tracking switch with high linearity is introduced to sample the input signal up to 75 MHz. A two-stage amplifier with hybrid frequency compensation is developed to achieve both high bandwidth and large swing with low power dissipation. The measured result shows that the ADC achieves over 77 dB spurious free dynamic range (SFDR) and 57.3 dB signal-to-noise-plus-distortion ratio (SNDR) within the first Nyquist zone and maintains over 70 dB SFDR and 55.3 dB SNDR for input signal up to 75 MHz. The peak differential nonlinearity (DNL) and integral nonlinearity (INL) are ±0.2 LSB and ±0.3 LSB, respectively. The ADC consumes 15.6 mW at the sampling rate of 40 MHz from a 1.2-V supply voltage, and achieves a figure-of-merit (FOM) value of 0.22 pJ per conversion step.     

A wide input bandwidth 7-bit 300-MSample/s folding and current-mode interpolating ADC

A 7-bit Nyquist folding and interpolating analog-to-digital converter (ADC) that converts at 300 MSamples/s is presented. Using current-mode signal processing techniques for analog preprocessing and a front-end sample-and-hold, the proposed 7-bit folding and interpolating ADC yields a wide input bandwidth up to 60 MHz with six effective number of bits. The ADC consumes 200 mW from a 3.3-V power supply. The chip occupies 1.2 mm/sup 2/ active area, fabricated in 0.35-/spl mu/m CMOS.     

A 10 b, 20 Msample/s, 35 mW pipeline A/D converter

This paper describes a 10 b, 20 Msample/s pipeline A/D converter implemented in 1.2 μm CMOS technology which achieves a power dissipation of 35 mW at full speed operation. Circuit techniques used to achieve this level of power dissipation include digital correction to allow the use of dynamic comparators, and optimum scaling of capacitor values through the pipeline. Also, to be compatible with low voltage mixed-signal system environments, a switched capacitor (SC) circuit in each pipeline stage is implemented and operated at 3.3 V with a new high-speed, low-voltage operational amplifier and charge pump circuits. Measured performance includes 0.6 LSB of INL, 59.1 dB of SNDR (Signal-to-Noise-plus-Distortion-Ratio) for 100 kHz input at 20 Msample/s. At Nyquist sampling (10 MHz input) SNDR is 55.0 dB. Differential input range is ±1 V, and measured input referred RMS noise is 220 μV. The power dissipation at 1 MS/s is below 3 mW with 58 dB of SNDR     

A 12-bit 20-Msample/s pipelined analog-to-digital converter with nested digital background calibration

A 12-bit 20-Msample/s pipelined analog-to-digital converter (ADC) is calibrated in the background using an algorithmic ADC, which is itself calibrated in the foreground. The overall calibration architecture is nested. The calibration overcomes the circuit nonidealities caused by capacitor mismatch and finite operational amplifier (opamp) gain both in the pipelined ADC and the algorithmic ADC. With a 58-kHz sinusoidal input, test results show that the pipelined ADC achieves a peak signal-to-noise-and-distortion ratio (SNDR) of 70.8 dB, a peak spurious-free dynamic range (SFDR) of 93.3 dB, a total harmonic distortion (THD) of -92.9 dB, and a peak integral nonlinearity (INL) of 0.47 least significant bit (LSB). The total power dissipation is 254 mW from 3.3 V. The active area is 7.5 mm/sup 2/ in 0.35-/spl mu/m CMOS.     

一种10位250 MS/s电荷域流水线ADC

提出了一种高速、低功耗、小面积的10位 250 MS/s 模数转换器(ADC)。该ADC采用电荷域流水线结构,消除了高增益带宽积的跨导运算放大器,降低了ADC功耗。采用流水线逐级电荷缩减技术,降低了后级电路的电荷范围,减小了芯片面积。测试结果表明,在250 MS/s采样速率、9.9 MHz输入正弦信号的条件下,该ADC的无杂散动态范围(SFDR)为64.4 dB,信噪失真比(SNDR)为57.7 dB,功耗为45 mW。     

A 10-bit 100 MSamples/s BiCMOS D/A Converter

This paper presents a 10-bit Digital-to-Analogue Converter (DAC) based on the current steering principle. The DAC is processed in a 0.8µm BiCMOS process and is designed to operate at a sampling rate of 100MSamples/s. The DAC is intended for applications using direct digital synthesis, and focus has been set on reducing dynamic nonlinearities to achieve a high spurious free dynamic range (SFDR) at high generated frequencies. The main part of the DAC consists of a matrix of current cells. Each current cell contains an emitter-coupled logic (ECL) flip-flop, clocked by a global ECL clock to ensure accurate clocking. A bipolar differential pair, with a cascode CMOS current sink, steered by the differential output of the ECL flip-flop, is used in each current cell to steer the current. The DAC operates at 5V, and has a power consumption of approximately 650mW. The area of the chip-core is 2.2mm × 2.2mm. The measured integral nonlinearity (INL) and differential nonlinearity (DNL) are both approximately 2 LSB. At a generated frequency of f _g0.1 f _s(f _s = 100MSamples/s) the measured SFDR is 50dB, and at f _g0.3 f _s the measured SFDR is as high as 43dB. The DAC is operating up to a sampling frequency of approximately 140MSamples/s. The DAC uses the hierarchical switching scheme and therefore the dynamic performance is not described well using the conventional glitch energy. A new energy measure that replaces the conventional glitch energy is therefore proposed. This energy measure is especially useful during the design phase.