Single-Mode As–S Glass Fibers

Single-mode As–S glass fibers with a core diameter from 3 to 20 m and a clad diameter of 125 m are prepared by the double-crucible method. The cutoff wavelength of the fibers is 0.9–6 m. The lowest transmission losses in the fibers at 2.2–2.3 m are 100 dB/km, and their mean bending strength is 800–1000 MPa.     

The role of starting powder size on the compressive response of stand-alone plasma-sprayed alumina coatings

Cylindrical stand-alone tubes of plasma-sprayed alumina were tested in uniaxial compression at room temperature, using strain gages to monitor axial strains. The effect of lamella size on the mechanical response was investigated by employing different starting powders to fabricate samples. The average powder sizes investigated included 9 m, 19 m and 32 m alumina; the resulting effective lamella diameters were 10 m, 28 m, and 55 m, respectively. Similar stress-strain hysteresis was observed on unloading in all tubes, independent of lamella size. A strong correlation between the failure stress and the cumulative strain at failure was also observed for tubes fabricated from the three powders. For samples with approximately constant densities, tubes plasma sprayed with the 9 m powder exhibited greater moduli than tubes sprayed from either 19 or 32 m powders. This difference was attributed to the greater percentage of unmelted -Al₂O₃ in the coating.     

Microstructure-property studies in friction-stir welded, Thixomolded magnesium alloy AM60

Thixomolded magnesium alloy AM60 plates joined by friction-stir welding were observed to be as strong or stronger than the unwelded base material. The thixotropic microstructures of the as-molded plates consisted of either 3% or 18% primary solid fraction of -Mg globules (45 m average size) in a eutectic mixture consisting of -Mg grains (10 m) surrounded by Mg₁₇Al₁₂ intermetallic grains in the -Mg grain boundaries (having an average size of 1–2 m). This complex, composite microstructure became a homogeneous (Mg + 6% Al)), recrystallized, equiaxed grain (10–15 m) microstructure in the weld zone.     

Crystal growth of U2D2 solid3He

We have measured the growth rate of single crystal U2D2 solid³He in the superfluid B phase as a function of chemical potential difference between the solid and liquid for temperatures between 0.4 and 0.9 T_N. The growth rate was not proportional to , with very slow growth rates for less than about 10 erg/cm³. For larger values of the growth rate depended weakly on temperature and the growth was attributed to a quantum growth mechanism due to screw dislocations. The melting rate was too fast to be measured quantitatively, but was slower at higher temperatures.     

A note on the similarity solutions for free convection on a vertical plate

Summary The similarity solutions for free convection on a vertical plate when the (non-dimensional) plate temperature is x and when the (non-dimensional) surface heat flux is –x are considered. Solutions valid for 1 and 1 are obtained. Further, for the first problem it is shown that there is a value ₀, dependent on the Prandtl number, such that solutions of the similarity equations are possible only for >₀, and for the second problem that solutions are possible only for >–1 (for all Prandtl numbers). In both cases the solutions becomes singular as ₀ and as –1, and the natures of these singularities are discussed.     

Measurements of chemical potentials in superconducting tin whiskers

A superconductor / normal conductor potential probe pair was used to measure differences between the time-averaged electrochemical potentials _p of Cooper pairs and of quasiparticle excitations caused by a phase-slip center in several experimental situations. The results can only be understood by assuming that at a larger distance from the phase-slip center differs from the proposal of Skocpol, Beasley, and Tinkham by showing a swinging over or swinging below _p . We propose a modified slope of as a function of site. Possible explanations are discussed. The multiple-contact samples used also allow the study of the influence of phase-slip centers already present on the relaxation of nonequilibrium quasiparticles.     

Particle size control of 1,3,5-triamino-2,4,6-trinitrobenzene by recrystallization from DMSO

Batches of up to 46g of the insensitive explosive 1,3,5-triamino-2,4,6-trinitrobenzene (TATB) have been recrystallized from DMSO in an effort to prepare larger particle-size material for recycling previously-used TATB and also for use in special formulations. The first part of the study investigated the conditions required to shift the particle-size distribution maximum from 50–70 m to several hundred micrometres in diameter. Distributions peaking at 200–246 m were successfully produced by varying the cooldown rate and degree of agitation during cooling. The second part of the study emphasized regeneration of the standard 50–70 m distribution from submicron size (ultrafine TATB) particles. The distributions peaking at 76–88 m, 27–31 m, and 15–17 m, successfully bracketed the target particle sizes, were grown by changing the degree of solution saturation. The choice of saturation temperature for the TATB/DMSO solution was based on earlier small-scale recrystallization and solubility work.     

Electron-phonon coupling as a mechanism for high-temperature superconductivity

We have solved the Eliashberg gap equations which are valid for arbitrary phonon frequency, (_ph), electron-phonon coupling constant, (), and screened Coulomb interaction, ( ^*). We have used values of (_ph),, and ( ^*) appropriate to the cuprate superconductors, and calculated the density of states, the pair potential., and the value of the gap at T=0 K. Using the linearized Eliashberg equations in the matrix representation, we have calculatedT _c and 2/k T _c . We have found that we can account for the highT _c 's in the cuprates with reasonable values for, ^*, and _ph.     

Spectral Reflectivity of Ceramics of Cubic Zirconium Oxide on the Wavelength of 0.63 μm under Intense Surface Heating above the Melting Point and Subsequent Cooling

The experimental data on the normally hemispherical reflectivity of zirconium oxide ceramics are obtained for the wavelength of 0.63 m in the course of the first cycle of heating by concentrated laser radiation up to temperatures above the melting point and free cooling in ambient air. The obtained data are compared with analogous results of the second and subsequent cycles of heating and cooling. Analysis is made of the effect of the temperature field in the heated layer on the reflectivity and on the effective temperature measured by a pyrometer.     

Porous HA ceramic for bone replacement: Role of the pores and interconnections – experimental study in the rabbit

Hydroxyapatite (HA) porous ceramics are increasingly used in biomedical applications. Their physical characteristics, such as porous volume, require perfect control of the pore shape, as well as the number and the size of their interconnections.The aim of our study was to evaluate a new HA ceramic using polymethylmethacrylate microbeads (PMMA) as the porous agent. Four interconnection sizes (30, 60, 100 and 130 m) with a 175–260 m pore size and three pore sizes (175–260, 260–350 and 350–435 m) for a 130 m interconnection size were tested. Various HA implants were appraised by microscopic evaluation in a 4.6×10 mm rabbit femur cancellous bone defect 12 weeks after implantation. The best osteoconduction result was obtained in the center of the ceramic by means of a 130 m interconnection size and a 175–260 m mean pore size. Bone formation obtained within the pores was double that obtained in our previous study where naphtalen microbeads were used as the porous agents.© 2001 Kluwer Academic Publishers     

High-Rate IR Laser Evaporation of Silica Glass

IR (10.6 m) laser irradiation of silica glass preforms ensures rapid evaporation of the surface layer. The resulting deposit consists of amorphous SiO₂ with a particle size of 70 nm.     

Shock consolidation of diamond powders

Fine and coarse diamond powders were shock-compacted at peak pressures of 77, 90, and 108 GPa. The densification and consolidation mechanisms of diamond powders under shock compression were investigated. The densification behaviour of the diamond powders depended strongly on the particle size of the starting materials. Fine diamond powders were densified primarily by plastic deformation, while coarse diamond powders were densified mainly by particle fracture. The relative densities of the compacted diamond samples increased with an increase in the initial particle size of the diamond and with shock pressure. The consolidation mechanism of the diamond powders under shock compression was closely related to the densification mechanism, and depended on the initial particle size of the diamond. At a shock pressure of 90 GPa, particle sizes of 2 to 4 m grade and 10 to 20 m grade were desirable as the starting material in order to produce well-bonded diamond compacts. Diamond compacts having microhardness values over 80 GPa were obtained from 2 to 4 m grade and 10 to 20 m grade diamond powders at a shock pressure of 90 G Pa, and their relative densities were 88.5% and 91.0%, respectively.     

Numerical study of spectral intensity of emission and absorption of the CO2 and CO molecules under vibrationally nonequilibrium conditions

Numerical calculations are performed of the spectral intensity of emission and absorption of the 4.3- and 2.7-m bands of CO₂ and of the 4.7-m band of CO under conditions of nonequilibrium excitation of the vibrational degrees of freedom.Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 42, No. 5, pp. 805–813, May, 1982.     

Submicron diameter nickel filaments and their polymer-matrix composites

Discontinuous nickel filaments of diameter 0.4 m and having a carbon core of diameter 0.1 m were fabricated by electroplating nickel on discontinuous carbon filaments. They exhibited a grain size of 0.016 m and electrical resistivity of about 5 × 10^–6 ·cm. In an amount as low as 7 vol.% in a polymer (polyether sulfone) matrix, they resulted in a composite exhibiting electromagnetic interference shielding effectiveness of 87 dB and reflection coefficient 0.95 at 1–2 GHz, tensile strength 52 MPa, tensile ductility 1.0%, and density 1.87 g/cm³.     

Hydrothermal synthesis of barium titanate fine particles from amorphous and crystalline titania

Barium titanate fine particles of cubic system were synthesized hydrothermally from aqueous barium hydroxide solutions with fine particles of either amorphous or crystalline (rutile) titania in suspension. The mean size of barium titanate particles prepared from amorphous titania ranged from 0.03 m to 0.11 m, depending on hydrothermal conditions. The particle size approximately agreed with the crystallite size (0.04–0.09 m). On the other hand, the mean size of barium titanate particles prepared from rutile titania ranged from 0.2 to 0.7 m, which was about six times as large as the crystallite size. The difference of sizes of barium titanate particles prepared might be ascribed to the difference in dissolution rates of amorphous or crystalline titania particles.Nomenclature mean particle size, m - BT barium to titanium molar ratio - d crystallite size, m - K shape factor appearing in Equation 3 - half value breadth of diffraction peak - lattice strain - Bragg diffraction angle, degree - wave length of X-ray, urn - _g geometric standard deviation defined by 84.1%-size/50%-size in a log normal size distribution     

Structure parameters of metal-fiber heat pipe wicks

The results of an experimental investigation of local and average values of permeability and effective pore diameter for metal-fiber wicks, using a laser-Doppler velocity measurement, are presented and discussed.Notation K permeability coefficient, m² - V filtration rate, m/sec - viscosity, N·sec/m² - dp/dx pressure gradient - rms deviation - f_i probability density distribution,m^–1 - D pore diameter,m - E excess - A asymmetry The 50-Year Anniversary of the Great October Socialist Revolution Kiev Polytechnic Institute.Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 35, No. 5, pp. 777–781, November, 1978.     

Preparation of barium titanate ultrafine particles from amorphous titania by a hydrothermal method and specific dielectric constants of sintered discs of the prepared particles

Barium titanate ultrafine particles were synthesized from amorphous titania by a hydrothermal method. The mean size of the barium titanate particles prepared at a hydrothermal treatment time of 4 h, was nearly equal to 0.04 5 m in the range of barium-to-titanium molar ratio (BT) 2, and approximately agreed well with the crystallite size. At a BT molar ratio of 1.0, the mean particle size increased to 0.2 m, while the crystallite size remained constant at 0.045 m. When the particle size ranged from 0.12–0.20 m, prepared for the BT molar ratio of 1.0–1.4, the specific dielectric constant for a sintered disc composed of these particles attained a value of 5000 or more. As the BT molar ratio increased to exceed 1.5, when the mean particle size decreased from 0.13 m to 0.045 m, the specific dielectric constant for the sintered disc was decreased greatly. The specific dielectric constant for the sintered disc can be correlated well with the size of the composing particles.     

Magnetic Co2Y ferrite, Ba2Co2Fe12O22 fibres produced by a blow spun process

Gel fibres of Co2Y,Ba2Co2Fe12O22, were blow spun from an aqueous inorganic sol and calcined at temperatures of up to 1200°C. The ceramic fibres were shown by X-ray diffraction to form crystalline Co2Y at 1000°C, and surface area and porosity measurements indicated an unusually high degree of sintering at this temperature. The fibres also demonstrated a small grain size of 1–3 m across the hexagonal plane and 0.1–0.3 m thickness at 1000°C. This only increased to 3 m in diameter and 1 m thickness even at temperature up to 1200°C. The fibrous nature combined with the improved microstructures could be an important factor in improving the magnetic properties of this material.     

Preparation of Si3N4 whiskers by reaction of wheat husks with NH3

-Si₃N₄ whiskers that are 1–10 mm long and 0.5–1.1 m thick were obtained by the reaction of wheat husks with NH₃ at 1250–1450 °C. A maximum whisker yield of about 30% was obtained at 1450 °C with the addition of an iron impurity. Whiskers with 1.3–2.2 m thickness (average 1.6 m) were obtained by the addition of an H₂S impurity. Thin whiskers with periodic thick and thin diameters were also obtained.     

Structure and properties of injection-moulded nylon-6

The microstructure and morphology of injection-moulded nylon-6 has been studied using wide-angle and small-angle X-ray diffraction, optical microscopy and a density measurement technique. A non-spherulitic surface layer consisting of a metastable pseudohexagonal phase surrounds the moulding and the thickness of the layer is sensitive to mould temperature. This outer structure gives way to a monoclinic phase containing spherulites between 3 and 6 m diameter. The central core of the moulding consists almost entirely of the phase with spherulites 6 m diameter, approximately. Exposure of nylon-6 to boiling water had no significant effect on the morphology of the moulding but the phase in the surface layer was transformed to the monoclinic phase.