共查询到20条相似文献,搜索用时 187 毫秒
1.
循环流化床烟气脱硫中物料平衡计算及试验研究 总被引:1,自引:0,他引:1
通过对干法烟气脱硫物料平衡计算,确定脱硫塔内固体颗粒物平衡浓度和达到平衡浓度所需要的时间, 并和实测值加以比较.在一台循环流化床烟气脱硫装置上,研究了固体颗粒物浓度对装置脱硫效率影响、阻力特性以及固体颗粒物循环对脱硫装置稳定运行的影响.结果表明,固体颗粒物的循环可以使脱硫效率提高10%-15%, 脱硫系统物料循环平衡的时间大约为30 min.综合实验结果,循环流化床烟气脱硫塔内固体颗粒物浓度宜控制在 600-1 000 g/m3之间. 相似文献
2.
3.
循环流化床常温半干法烟气脱硫技术的工程示范研究 总被引:4,自引:0,他引:4
在清华大学试验电厂开展了常温半干法循环流化床烟气脱硫技术的工程示范研究。示范装置的设计处理烟气量为20.000Nm^3/h。脱硫塔内部采用了特殊的结构.以实现物料的内循环。针对影响脱硫效率的主要因素,如反应塔出口烟气温度与绝热饱和露点的温度差(ASAT),钙硫比,床内物料浓度。以及CaCl2添加剂等,进行了一系列的试验。试验表明,当钙硫比为1.3,ASAT为7C时,脱硫效率可以达到85%;在同样条件下,在石灰浆中添加少量的CaCl2,脱硫效率可达到90%。同时,对系统脱硫过程进行理论分析,提出增加脱硫离子反应时间的方法。图6参7 相似文献
4.
在银川热电厂5号炉(150t/h)回流式循环流化床烟气脱硫装置开展了半干法循环流化床烟气脱硫技术的工程试验研究,该脱硫装置的设计处理烟气量为16000m^3/h。脱硫塔内部及顶部采用了特殊回流结构设计,实现物料塔内内循环。减少除尘装置入口浓度。通过工业试验,研究了钙硫比、喷水量等参数对系统脱硫效率的影响。试验结果表明,当钙硫比为1.3、塔内温度70℃、塔内浓度为800g/m^3时,系统脱硫效率可以达到90%,粉尘排放浓度为80mg/m^3,脱硫系统阻力小于1.5kPa。 相似文献
5.
循环流化床物料平衡是循环流化床燃烧的核心和基础,它影响到循环流化床燃烧效率和脱硫效率,并决定燃烧室内的热负荷分布。循环流化床“一进二出”的物料平衡系统是循环流化床的核心概念,也是理解循环流化床物料平衡的关键。本文介绍并分析了循环床物料平衡的某些问题,如循环流化床定态设计、床料质量和物料平衡模型等。循环流化床运行需要高的“床料质量”和较大物料循环量,要求流化床锅炉分离器分离效率曲线存在一个清晰的100%分离粒径截止点。循环流化床内物料平衡除了受分离器效率影响外,还受到给煤成灰及磨耗特性、床内颗粒分层、排渣方式及效率等因素的影响。 相似文献
6.
采用三准则相似理论设计了循环流化床烟气脱硫气固两相流动试验台.通过对循环流化床脱硫反应器试验装置内沿高度方向阻力分布和不同高度截面上局部颗粒质量通量的测量,详细地研究了脱硫反应器内气固两相流动规律和内循环特性.结果表明:脱硫反应器阻力主要集中在文丘里管段,而且随着循环物料量和气体流量的增加,系统阻力显著增加;脱硫反应器内气固两相流动呈典型的环核流动结构,边壁下降流颗粒浓度高,中心区域上升流颗粒浓度低,且固体质量回流比率随着脱硫反应器高度的上升而下降.研究结果为循环流化床烟气脱硫系统的设计与放大提供了依据. 相似文献
7.
在一台75t/h燃煤锅炉上,设计建造了双循环流化床烟气悬浮脱硫系统,在脱硫系统运行前后,对配套电除尘器入口处烟气的温度、湿度、化学成份、粉尘的粒径、表观形貌和比电阻等相关特性进行了比较分析。结果显示,在脱硫系统运行后,可使除尘器入口处烟气的湿度增加,温度降低,尘粒的比电阻下降,从而提高了系统的脱硫效率与电除尘器的除尘效率。还研究了循环流化床烟气脱硫装置对电除尘器工作稳定性和除尘效率的影响,同时提出了应对措施。 相似文献
8.
9.
10.
11.
在中温(400℃~800℃)干法循环流化床烟气脱硫工艺中,由于反应产物CaSO4的比摩尔容积大于脱硫剂CaO的比摩尔容积,进而使得SO2气体在脱硫剂颗粒内的扩散变得非常困难,从而影响了脱硫反应的进行和脱硫剂的利用率。为了提高钙利用率,采用中高温(800℃)硫化、低温(150℃)蒸汽活化的方法来处理乏脱硫剂。在文中提出了移动床式蒸汽活化器和流动床式蒸汽活化器两种方案,并进行了计算和分析。 相似文献
12.
《Energy Conversion and Management》2005,46(7-8):1043-1057
An EHC (electrically heated catalyst) of a four stroke motorcycle engine with heat storing material was used to investigate the effect of input energy on the carbon monoxide (CO) conversion efficiency after cold start. The factors studied included the length of the heat storing material, heating temperature and pre-heating time.The stainless steel heat storing material was 15 mm wide and 0.3 mm deep and was installed at the inlet and mid-section of the catalyst. The settings of the parameters were heat storing material lengths of 30 and 60 cm, pre-heating time of 5, 15 and 25 s, a CO setting level of 1.3% and 1.8% and a heating temperature of 140, 180 and 220 °C.It was revealed that for the shorter heat storing material, better conversion efficiency was attained when heating at the inlet. Heating at the mid-section of the catalyst with the same length of heat storing material resulted in less energy stored, quicker heat dissipation and more frequent re-heating required. In contrast, with a longer heat storing material, the temperature rise was more gradual and more heat was absorbed, resulting in a more stable overall temperature development. It was further showed that under the same input energy, the shorter heat storing material provided a higher CO conversion efficiency than the longer material. Further, a threshold total input energy for achieving a CO conversion efficiency above 65% was found to be 100 kJ. 相似文献
13.
为了进一步优化微燃烧室的设计,以最大化提高微燃烧室的能量转换效率及微热光电系统的整体工作效率,在前期工作的基础上设计了不同多孔介质材料及喷嘴/燃烧室内径比的多孔介质微燃烧室.通过实验验证,针对多孔介质微燃烧室内的氢氧预混燃烧进行了数值模拟计算,研究结果表明,多孔介质材料,喷嘴/燃烧室内径比对微燃烧室内的微尺度燃烧有重要影响,微燃烧室在多孔介质材料为SiC, 喷嘴/燃烧室内径比为0.27时燃烧效率最高,有利于提高微热光电系统的整体效率. 相似文献
14.
15.
This paper adopts the hybrid numerical method to research the heat conduction of the functionally graded materials (FGM) plates under the exponential heat source load. Based on the heat balance equation, the hybrid numerical method theory is established through the method of weighted residuals. Then inversely Fourier transformed equation is applied to get the temperature distribution of FGM plates. And the temperature variation law at different positions is obtained in the loading time. The results show that at different positions temperature changing was consistent with heat source and gradually reduced with the distance away from the heat source. The heat transfer efficiency is related to the material performance of the surface. 相似文献
16.
《Energy Policy》2013
Scenario-based studies agree that the technical potential for CO2 emissions reduction from the housing stock is large. This paper explores how a market might be developed for the refurbishment activities assumed in these scenarios, taking the existing market for repair, maintenance and improvement (RMI) as its starting point. Interviews with 16 small and medium-sized enterprises (SMEs) in the construction industry reveal the interdependence of products, practices and processes in housing renovation activities. Conservative practice as well as innovation can be understood as the outcome of multi-lateral influences on firms from other firms, clients, the material buildings and products in their working lives, and from regulations and regulators. Contractors' openness to innovation is contingent on an informal approach to risk assessment, taking account of cost, time efficiency, client demands, and installer confidence in the reliability of the resulting work. The implications of the research are discussed in relation to the need for new practices and processes on refurbishment projects, raising questions for future research on key questions of quality assurance, performance over time, the application of standards, and vocational training. 相似文献
17.
为了提高长轴深井泵的机组效率,在重庆市某大型长轴深井泵站改造的基础上,开展了生产性试验研究,以长轴深井泵机组为研究对象,进行了出厂与场地对比测试、影响因素变化前后场地对比测试等,探讨了转速、中间轴承材料等因素对机组效率的影响。结果表明,转速与中间轴承材料的选择可改变泵头效率与泵轴摩擦损失,进而影响机组效率,因此综合多种因素合理选择转速与中间轴承材料、减少轴的机械摩擦损失及合理确定选泵高效段范围是提高长轴深井泵机组效率、节约能耗的重要措施。 相似文献
18.
Numerical investigation of the thermal mechanism of the solid-liquid phase changing process
下载免费PDF全文
![点击此处可从《储能科学与技术》网站下载免费的PDF全文](/ch/ext_images/free.gif)
由于相变换热储能技术可以协调能量在时间和空间尺度的分配,成为了目前研究的热点问题。本工作用焓值法分别对充填低温无机盐相变材料的二维和三维管壳式相变储能换热器模型的储/放热特性进行了模拟研究,采用Boussinesq近似研究了液相区密度变化引起的自然对流的影响。研究表明换热器的入口温度对相变换热效率影响显著;在储热过程中自然对流发挥了重要作用,换热效率与液相区的运动状态直接相关,而放热过程中的热交换主要依靠热传导完成;三维模拟的结果表明换热管出口温度与管壁的平均努赛尔数高度相关,且换热管水平放置的换热效率略低于竖直放置。 相似文献
19.
明渠水面照射式紫外消毒器灭菌效能研究 总被引:4,自引:1,他引:3
研究明渠水面照射式紫外消毒对大肠菌群和细菌的杀灭效果,为明渠水面照射式紫外消毒用于污水消毒的运行和工程设计提供依据。采用配水和某污水处理厂二级出水,试验不同水层厚度(分别为5~25mm)条件下,不同流量(分别为2.5~20L/h)时,紫外线对大肠菌群和细菌的杀灭情况。试验结果表明,明渠水面照射式紫外消毒对大肠菌群和细菌的杀灭效果较好,同时受水层厚度和流量的影响,在一定条件下可发挥其最佳的效能。为提高消毒效果,建议在消毒箱内壁粘贴一些增强紫外线反射光的材料,以提高紫外光的利用率,建议在生产条件下采用并联多极组合式。 相似文献
20.
严寒地区多数农村住宅建筑围护结构热损失严重,造成其采暖能耗增加,强化建筑围护结构的保温性是提高建筑采暖效率的方式之一。以位于严寒地区的安达市某传统农宅为研究对象,采用EnergyPlus对该住宅围护结构的保温性能进行研究,并分析了建筑能耗情况,获得了建筑墙体、玻璃、屋顶等围护结构部位采用保温后的节能效率。研究结果表明:安达地区节能效率较好的墙体和屋顶保温材料为XPS保温板、玻璃窗结构形式为6mm+12mm+6mmLow-E低辐射玻璃;传统农宅采用建筑保温材料后,其节能率可达72.0%,从而降低了农村住宅采暖能耗,并可维持室内良好的热环境。 相似文献